210Pb and 210Po radionuclides in the urban air of Lodz, Poland

The concentration of two important radionuclides: ²¹⁰Pb and its decay product ²¹⁰Po in the urban air in the center of the Polish city of Lodz were measured during the winter and spring seasons of 2008–2009. Urban airborne particulate matter was collected using two methods: an Anderson 9-stage impactor, and a high-volume aerosol sampler type ASS500 working in the frames of the aerosol sampling network in Poland, established for radionuclide monitoring. Average concentrations for 10 months sampling period for ²¹⁰Pb and ²¹⁰Po were 0.556 and 0.067 mBq/m³, respectively. However remarkable fluctuations due to meteorological condition were observed: from 0.010 to 0.431 mBq/m³ for ²¹⁰Po and from 0.167 to 1.847 mBq/m³ for ²¹⁰Pb. The highest concentrations, almost 60% of the total activities, of both radionuclides were found in the first two fine aerosol fractions with particle diameters below 0.36 μm. The aerosol residence times calculated from the ²¹⁰Po/²¹⁰Pb ratio ranged from 7 to 120 days.     

Environmental radioactivity measurements in north–western Greece following the Fukushima nuclear accident

The impact of the Fukushima nuclear accident in north–western Greece was assessed through an environmental monitoring programme activated by the Nuclear Physics Laboratory of the University of Ioannina. Measurements of ¹³¹I were carried out in atmospheric particulate, ovine milk and grass samples. In daily aerosol samplings, radioiodine was first detected on March 25–26, 2011 and reached maximum levels, up to 294 μBq m^?3, between April 2 and April 4, 2011. In ovine milk samples, ¹³¹I concentrations ranged from 2.0 to 2.7 Bq L^?1 between April 2 and April 6, 2011, while an average activity of 2.7 Bq kg^?1 was measured in grass samples on April 4, 2011. The ^134,137Cs isotopes were below detection limits in all samples and could only be determined in the air, by analysis of multiple daily filters. A maximum average activity concentration of ¹³⁷Cs amounting to 24 μBq m^?3 was measured during the period from April 5 to April 9, 2011, with the ¹³⁴Cs/¹³⁷Cs activity ratio being close to unity. Activity concentrations were consistent with measurements conducted in other parts of the country and were well below those reported in May 1986 after the Chernobyl accident. The committed effective dose to the whole body and to the thyroid gland from inhalation of ¹³¹I was estimated for the adult and infant population and was found to be of no concern for the public health.     

Outdoor 222Radon concentrations monitoring in relation with particulate matter levels and possible health effects

Air quality monitoring could potentially improve exposure estimates for use in epidemiological studies. We investigated air quality by monitoring concentrations of ²²²Rn near the ground and particulate matter (PM) with an aerodynamic diameter less than or equal to 10 μm (PM10) and 2.5 μm (PM2.5) for Bucharest-Magurele periurban area. Atmospheric radon concentrations have been continuously monitored near the ground at 1 m height as well as at 10 m height. This paper presents time-series of radon concentrations monitoring in air near the ground measured during 1 January 2011–1 January 2012 by use of solid state nuclear track detectors SSNTD CR-39, exposed for 10 days periods. The daily average atmospheric radon concentration near the ground registered at 1 m height was found to be in range of 40.25 ± 7.53 Bq/m³, which was comparable with the daily average radon concentration of 44.92 ± 9.94 Bq/m³ recorded for period 1 August 2011–20 December 2011 at 10 m height by AlphaGUARD Radon monitor. Also, was done a comparative analysis of spatio-temporal variations in time series of outdoor radon concentration and PM in two size fractions (PM10 and PM2.5) in Bucharest Magurele area for 2011 year. The predominant recorded component in PM10 was PM2.5. Observational results show that recorded yearly average PM2.5 and PM10 concentrations were 35.96 μg/m³ and 40.91 μg/m³, respectively. The average ratio of PM2.5/PM10 was 87.9 % at this sampling site. However, in densely populated Bucharest urban and suburban areas the mean daily EC limit values for PM10, PM2.5 and attached ²²²Rn are frequently exceeded leading to serious public concern during the last years. The ambient air pollution measurements like as PM10 and PM2.5 levels are used as a proxy for personal exposure levels. Have been investigated also meteorological effects on the temporal patterns of atmospheric radon and particle matter.     

Monitoring of atmospheric 3H around Narora Atomic Power Station

Atmospheric tritium activity is measured regularly around Narora Atomic Power Station (NAPS) since gaseous waste, which contains tritium, is being released through a 145 m high stack at NAPS site. Atmospheric data collected during 2004–2008 shows a large variation of ³H concentration in air, fluctuating in the range of ≤0.2–91.6 Bq m^?3. Significantly, higher tritium levels were measured in samples near the site boundary (1.6 km) of NAPS compared to off-site locations. The atmospheric dilution factor was found to be in the range of 1.1 × 10^?7–7.3 × 10^?7 s m^?3. The scavenging ratio of NAPS site was found to be varying from 0.2 × 10⁴ to 14.1 × 10⁴ (Bq m^?3 rain water per Bq m^?3 air). The inhalation dose to a member of general public at different distances (1.6–30 km) from NAPS site was found to be ranged from 0.08–0.21 μSv year^?1.     

Determination of Pyrethroid and Organophosphorus Insecticides in Indoor Air by Microwave-Assisted Extraction with Gas Chromatography/Mass Spectrometry

The goal of this study was to evaluate the efficiency of microwave-assisted extraction for the recovery of pyrethroid and organophosphorus insecticides adsorbed on quartz fiber filters and C18 disks used for indoor air sampling. The extraction solvent, temperature, and time were optimized by spiking tests. The recoveries for the insecticides obtained by microwave-assisted extraction with acetone at 50°C for 5 min were between 71.9% and 119.2% with relative standard deviations between 0.3% and 9.3% at two spike levels (0.1 µg and 1.0 µg). The results of the microwave-assisted extraction under the validation conditions were comparable to those obtained by Soxhlet extraction, which was used as a reference technique. In a preliminary analysis, resmethrin and tetramethrin were determined in the indoor air of an apartment unit at concentrations of 7.8 ng/m³ and 66.0 ng/m³, respectively, using the microwave-assisted extraction-based method with gas chromatography/mass spectrometry.     

Determination of 13 estrogenic endocrine disrupting compounds in atmospheric particulate matter by pressurised liquid extraction and liquid chromatography-tandem mass spectrometry

This paper describes the optimisation of an analytical method for the simultaneous determination of up to 13 estrogenic endocrine disrupting compounds (EDCs), including natural and synthetic estrogens, alkylphenols, bisphenol A and phthalate esters, in atmospheric particulate matter. This methodology is based on pressurised liquid extraction and liquid chromatography-tandem mass spectrometry and is the first method described for analysis of estrogens in air. Samples were collected with high-volume samplers equipped with quartz microfiber filters. Two selected reaction monitoring transitions were chosen for identification and confirmation of the target compounds. Quantitation was performed by the internal standard method with the use of deuterated surrogate standards. The analytical features of the method were satisfactory: absolute recoveries were around 45 % for all compounds, except estrogens (～29 %), because of matrix effects. Repeatability was in all cases below 15 %. Quantitation limits of the method ranged from 5 pg/m³ (for diethylphthalate) to 83 pg/m³ (for 17-α-ethynylestradiol). As a part of the validation procedure, the developed method was applied to the analysis of eight air particulate samples (fine grain-size particles, PM_2.5) collected in industrial, urban and non-polluted suburban areas of A Coruña (NW of Spain). Results evidenced the presence of dibutylphthalate, diethylhexylphthalate and nonylphenol in all samples. The highest concentration corresponded to dibutylphthalate (54.7 ng/m³) in an industrial area. Daily exposure to these EDCs in terms of estradiol equivalents (3 pg/day for toddlers and 5 pg/day for adults) is not expected to pose a risk to human health.     

Radon concentration in air, hot spring water, and bottled mineral water in one hot spring area in Thailand

Hot springs are famous as spa resorts throughout the world. However, these areas usually have high natural radioactivity from radon gas. In this study radon concentrations in air, hot spring water, and bottled mineral water produced in a spa area of Suan Phueng district, Ratchaburi province, Thailand were measured. Radon concentrations in air were in the range of 10–17 and 11–147 Bq/m³ for outdoor and indoor, respectively. Committed effective dose from inhale of radon were assessed and found to be in the range of 0.004–0.025, 0.25–0.6, and 1.134 mSv/y for visitor, local people and resort workers, respectively. These doses were in the range of 1.2 mSv/y regulated by UNSCEAR for the general public. Radon in hot spring water ranged from 2–154 Bq/L. Radon in bottled mineral water produced from the hot spring water were in the range of 17–22 and 0.2–0.3 Bq/L for those that stored for 7 and 90 days, respectively, after production. Radon concentration levels were in the range of the US Environmental Protection Agency reference level for radon in air which is 148 Bq/m³ and alternative maximum concentration limit (AMCL) for raw water which is 150 Bq/L. However, when considering the USEPA (Maximum concentration limit), 11 Bq/L, for radon in drinking water, the mineral water should be stored for at least 8–9 days after bottling before selling to the market.     

Investigation of radon and thoron concentrations in a landmark skyscraper in Tokyo

The temporal variation of the radon concentration, and the radon and thoron concentrations every 3 months for a year were measured using two types of devices in a landmark skyscraper, the Tokyo Metropolitan Government Daiichi Building. In the measurement of temporal variation of the radon concentration using a pulse type ionization chamber, the average radon concentration was 21 ± 13 Bq m^?3 (2–68 Bq m^?3). The measured indoor radon concentration had a strong relationship with the operation of the mechanical ventilation system and the activities of the office workers. The radon concentration also increased together with temperature. Other environmental parameters, such as air pressure and relative humidity, were not related to the radon concentration. In the long-term measurements using a passive radon and thoron discriminative monitor, no seasonal variation was observed. The annual average concentrations of radon and thoron were 16 ± 8 and 16 ± 7 Bq m^?3, respectively. There was also no relationship between the two concentrations. The annual average effective dose for office workers in this skyscraper was estimated to be 0.08 mSv y^?1 for 2000 working hours per year. When considering the indoor radon exposure received from their residential dwellings using the annual mean radon concentration indoors in Japan (15.5 Bq m^?3), the annual average effective dose was estimated to be 0.37 mSv y^?1. This value was 31 % of the worldwide average annual effective dose.     

Ground level ozone (O3) associated with radon (222Rn) and particulate matter (PM) concentrations in Bucharest metropolitan area and adverse health effects

The aim of this paper is to contribute with new information in the application of ground based radon (²²²Rn) observations to atmospheric research, namely its relation with air pollution due to ground-level ozone (O₃) and particle matter in two size fractions (PM10 and PM2.5) for Bucharest metropolitan area in Romania. During January 1–December 31, 2011, ground levels of radon, ozone and particulate matter (PM) have been continuously monitored in synergy with the main meteorological parameters (air temperature, humidity and pressure), and daily global air quality indices. A systematic analysis of surface ozone observations of ground level radon, ozone and PM is presented. Observational results indicate the following yearly daily mean ground level concentrations: 40.26 ± 7.54 Bq/m³ for radon, 90.51 μg/m³ for ozone, 35.96 μg/m³ for PM2.5, and 40.91 μg/m³ for PM10. The assessment of the results showed the influence of local and meteorological conditions on the daily mean radon, ozone and PM concentrations. However, in densely populated metropolitan area of Bucharest the mean daily values of ozone, PM2.5, PM10, and attached ²²²Rn are sometimes higher than European Community limit values leading to serious public concern during the last years. Due to the high risk of increased levels of O₃, PM2.5, PM10, and attached ²²²Rn on human health respiratory function (especially for children and older persons), and urban green, the results are very useful for atmospheric, radiological protection, epidemiological and environmental studies.     

Determination of Cd and Pb in Honey by SF‐ICP‐MS: Validation Figures and Uncertainty of Results

Abstract

A method based on microwave‐assisted acid digestion of honey and quantification of Cd and Pb by Sector Field Inductively Coupled Plasma Mass Spectrometry was in‐house validated and the combined uncertainty was estimated according to the Eurachem/Citac Guide. Limits of detection and quantification were 0.07 and 0.20 ng g^?1 for Cd, and 0.70 and 2.10 ng g^?1 for Pb; recovery was 103.9% for Cd and 98.5% for Pb; repeatability was 10.7% for Cd and 18.5% for Pb; within‐laboratory reproducibility was 15.2% for Cd and 21.4% for Pb. Relative combined uncertainty in honey was 15% for Cd and 22% for Pb, with the main contribution coming from the within‐laboratory reproducibility. The method showed robustness when subjected to different working conditions and when applied to various Italian honeys. Cadmium content ranged 0.2–1.37 ng g^?1 and Pb 4.6–30.5 ng g^?1 in flower honeys, while the highest concentrations were presented by honeydew honeys.     

Determination of bismuth in atmospheric particulate matter by hydride generation and atomic absorption spectrometry

The particulates are collected on Whatman 41 cellulose filters and decomposed with sulfuric acid and hydrogen peroxide; bismuth is then measured by hydride generation/atomic absorption spectrometry. The detection limis is 0.08 ng m^?3 if 500 m³ of air is filtered through an 11-cm filter. Generally, the precision is better than 10%. The concentrations found in Ghent, Belgium varied between 0.1 and 0.8 ng m^?3. Bismuth was also determined in NBS Orchard leaves (SRM 1571); a value of 98.5 ± 15 ng g^?1 was found.     

Determination of Hg isotopic compositions in certified reference material NIES No. 13 Human Hair by cold vapor generation multi-collector inductively coupled plasma mass spectrometry

Hg isotopic ratios of NIES CRM No. 13 Human Hair were analyzed using cold vapor generation coupled to multi-collector inductively coupled plasma mass spectrometer to meet the growing demand for better understanding of Hg exposure routes by using Hg isotopic compositions in human hair samples. To validate and assure the accuracy of our analytical method, (1) the reproducibility of the Hg isotopic measurement was monitored and (2) the Hg isotopic compositions of four secondary reference materials—IAEA-085, IAEA-086, and CRPG-RL24H—were measured. Our results for NIES CRM No. 13 show the mass-dependent fractionation values of δ ¹⁹⁹Hg = (2.13 ± 0.07) ‰, δ ²⁰⁰Hg = (0.98 ± 0.08) ‰, δ ²⁰¹Hg = (2.77 ± 0.10) ‰, δ ²⁰²Hg = (1.89 ± 0.10) ‰, and δ ²⁰⁴Hg = (2.76 ± 0.16) ‰ (2SD, n = 11) and the mass-independent fractionation values of Δ ¹⁹⁹Hg = (1.65 ± 0.06) ‰, Δ ²⁰⁰Hg = (0.04 ± 0.04) ‰, Δ ²⁰¹Hg = (1.36 ± 0.07) ‰, and Δ ²⁰⁴Hg = (?0.04 ± 0.11) ‰ (2SD, n = 11). Interlaboratory comparison of the CRM performed at the University of Pau showed good agreement with the values obtained at NIES.     

A new approach for determination of crustal and trace elements in airborne particulate matter

An ICP-OES procedure was developed for fast and accurate determination of various crustal (Al, Ca, Fe, Mg, Si) and trace elements (Ba, Cu, Mn, Na, K, Sr, Ti, Zn) in airborne particulate matter. The method is based on a preliminary treatment of the aerosol samples with a mixture of nitric acid and hydrogen peroxide at elevated temperature leading to a mineralization of the organic sampling substrate, dissolution of soluble material and homogeneous suspension of the remaining non-soluble fraction. After dilution the derived slurry solutions were measured using ICP-OES. The reproducibility of analysis given as the relative standard deviation (% RSD) varied between 3.2 and 6.8% for bulk constituents such as Al, Ca, Fe, Mg and Si whereas values ranging from 3.5 to 9.1% were obtained for trace metals present with distinctly lower abundance in PM10 (e.g. Ba, Cu, Mn, Sr, Zn). The limits of detection (LOD) calculated as three times the standard deviation (3σ) of the signal derived from filter blank samples ranged from approximately 1?ng?m^?3 (Sr) to 71?ng?m^?3(Ca). The developed procedure was evaluated by comparing the obtained results with the findings derived for the same set of aerosol samples analyzed using a microwave procedure for sample dissolution with subsequent ICP-OES analysis. Finally the developed procedure was applied for the analysis of crustal and trace elements in PM10 samples collected at an urban site (Getreidemarkt, Vienna) and a rural site (Hartberg, Styria), in Austria. The concentrations of the investigated crustal elements varied between some hundred ng?m^?3 and few µg?m^?3 with highest concentrations for Fe and Si, distinctly reduced concentrations ranging from some ng?m^?3 (Sr) to more than hundred ng?m^?3 (K) were found for trace elements. Observed PM10 concentrations were found to be in accordance to literature findings from urban sites in central Europe.     

Pharmaceutical grade sodium [99mTc] pertechnetate from low specific activity 99Mo using an automated 99Mo/99mTc-TCM-autosolex generator

Performance study of a computer controlled automated closed cyclic module for the separation and recovery of ^99mTc from low specific activity (n, γ) ⁹⁹Mo using methyl ethyl ketone (MEK) solvent extraction technique named ⁹⁹Mo/^99mTc-TCM-AUTOSOLEX (Technetium automated solvent extraction) Generator is described. The entire system is automated and controlled by a user-friendly PC based graphical user interface that actually supervises process via an embedded system based electronic controller. The average yield of separation of ^99mTc was above 85 % and ⁹⁹Mo breakthrough in ^99mTc pertechnetate was <0.002 %. The sodium pertechnetate obtained was a clear solution having pH 6–7, Radiochemical (RC). Purity >99 %, MEK content <0.1 % (v/v), Al and Mo content <10 µg/ml. R. C. Purity of ^99mTc-radiopharmaceuticals studied was not less than 96 %. Bio-Quality control studies confirm that sodium pertechnetate obtained was sterile and pyrogen free. Imaging studies in animals and humans with limited radiopharmaceuticals show that the quality of ^99mTc-pertechenate obtained in the present module was good enough to do clinical study.     

Mixed immunoassay design for multiple chemical residues detection

In this research, a mixed immunoassay design for multiple chemical residues detection based on combined reverse competitive enzyme-linked immunosorbent assay (ELISA) procedure was developed. This method integrated two reverse ELISA reactions in one assay by labeling horseradish peroxidase to deoxynivalenol (DON) and orbifloxacin. Within this method, IC50 of the two mAbs for each analyte we produced ranged from 23?～?68 ng?mL^?1 for DONs and 4.1?～?49 ng?mL^?1 for quinolones (QNs). The limit of detection measured by IC10 was achieved at 0.45–1.3 ng?mL^?1 for DONs and 0.59–6.9 ng?mL^?1 for QNs, which was lower than the maximum residue levels. Recoveries in negative samples spiked at concentrations of 100, 200, and 500 ng?mL^?1 ranged from 91.3 to 102.2 % for DONs and 88.7–98.05 % for QNs with relative standard deviation less than 9.88 and 12.67 %. The results demonstrated that this developed immunoassay was suitable for screening of low molecular weight contaminants.

Radionuclides from Fukushima accident in Thessaloniki, Greece (40°N) and Milano, Italy (45°)

¹³¹I, ¹³⁷Cs and ¹³⁴Cs were observed in environmental samples in Milano (40°N), Italy and Thessaloniki (45°N), Greece, soon after the nuclear accident in Fukushima, Japan. The radionuclide concentrations were determined and studied as a function of time. In Thessaloniki the ¹³¹I in air was observed for the first time on March 24, 2011. In Milano, the first evidence of Fukushima fallout has been confirmed with ¹³¹I and ¹³⁷Cs measured in wet precipitation collected 2 days later. The maximum ¹³¹I activity concentration in air of 467 ± 25 μBq m^?3, observed in Milano on April 3–4, 2011, was almost similar to the highest value of 497 ± 53 μBq m^?3 observed in Thessaloniki. The ¹³⁴Cs/¹³⁷Cs activity ratio values in air were around 1 in both regions. Soil, grass and milk samples were contaminated with ¹³¹I and ¹³⁷Cs at a low level. Finally, a dose assessment for these two areas showed clearly that the detected activities in all environmental samples were far below levels of concern.     

Practicality of Tetragonal Nano-Zirconia as a Prospective Sorbent in the Preparation of 99Mo/99mTc Generator for Biomedical Applications

The feasibility of using tetragonal nano-zirconia (t-ZrO₂) as an effective sorbent for developing a ⁹⁹Mo/^99mTc chromatographic generator was demonstrated. The structural characteristics of the sorbent matrix were investigated by different analytical techniques such as XRD, BET surface area analysis, FT-IR, TEM etc. The material synthesized was nanocrystalline, in tetragonal phase with an average particle size of ~7 nm and a large surface area of 340 m² g^?1. The equilibrium sorption capacity of t-ZrO₂ is >250 mg Mo g^?1. The present study indicates that ⁹⁹Mo is both strongly and selectively retained by t-ZrO₂ at acidic pH and ^99mTc could be readily eluted from it, using 0.9% NaCl solution. A 9.25 GBq (250 mCi) t-ZrO₂ based chromatographic ⁹⁹Mo/^99mTc generator was developed and its performance was repeatedly evaluated for 10 days. ^99mTc could be eluted with >85% yield having acceptable radionuclidic, radiochemical and chemical purity for clinical applications. The compatibility of the product in the preparation of ^99mTc labeled formulations such as ^99mTc-EC and ^99mTc-DMSA was evaluated and found to be satisfactory.     

Analysis of anthropogenic and biogenic lipids in the aerosol of a coastal area in East Mediterranean Sea

Summary The concentrations of lipids were determined in atmospheric particle samples, collected seasonally, in an urban coastal area of the Island of Crete. Lipid compound classes, such as n-alkanes, hopanes and steranes, PAH, fatty alcohols, fatty acids and fatty acids selts, were determined by GC-FID and GC-MS analysis. The concentrations ranged between 56–215 ng/m³ for n-alkanes, 10–52 ng/m³ for PAH, 2–31 ng/m³ for fatty alcohols, 13–279 ng/m³ for fatty acids and 24–220 ng/m³ for fatty acid salts. -Oxocarboxylic acids were also determined as salts, indicating the atmospheric oxidation of unsaturated fatty acids.     

A double-stage tube furnace—acid-trapping protocol for the pre-concentration of mercury from solid samples for isotopic analysis

High-precision mercury (Hg) stable isotopic analysis requires relatively large amounts of Hg (>10 ng). Consequently, the extraction of Hg from natural samples with low Hg concentrations (<1–20 ng/g) by wet chemistry is challenging. Combustion–trapping techniques have been shown to be an appropriate alternative [1]. Here, we detail a modified off-line Hg pre-concentration protocol that is based on combustion and trapping. Hg in solid samples is thermally reduced and volatilized in a pure O₂ stream using a temperature-programmed combustion furnace. A second furnace, kept at 1,000 °C, decomposes combustion products into H₂O, CO₂, SO₂, etc. The O₂ carrier gas, including combustion products and elemental Hg, is then purged into a 40 % (v/v) acid-trapping solution. The method was optimized by assessing the variations of Hg pre-concentration efficiency and Hg isotopic compositions as a function of acid ratio, gas flow rate, and temperature ramp rate for two certified reference materials of bituminous coals. Acid ratios of 2HNO₃/1HCl (v/v), 25 mL/min O₂ flow rate, and a dynamic temperature ramp rate (15 °C/min for 25–150 and 600–900 °C; 2.5 °C/min for 150–600 °C) were found to give optimal results. Hg step-release experiments indicated that significant Hg isotopic fractionation occurred during sample combustion. However, no systematic dependence of Hg isotopic compositions on Hg recovery (81–102 %) was observed. The tested 340 samples including coal, coal-associated rocks, fly ash, bottom ash, peat, and black shale sediments with Hg concentrations varying from <5 ng/g to 10 μg/g showed that most Hg recoveries were within the acceptable range of 80–120 %. This protocol has the advantages of a short sample processing time (～3.5 h) and limited transfer of residual sample matrix into the Hg trapping solution. This in turn limits matrix interferences on the Hg reduction efficiency of the cold vapor generator used for Hg isotopic analysis.     

Collection and Determination of Mercury in Air

A method has been developed for the determination of low concentrations of mercury in air (nanograms/m³), i.e. in the range of the believed natural levels of mercury in the atmosphere (20 ng/m³). Mercury vapour has been collected from up to 200 1 of air in glass tubes containing thin films of gold on sieved ceramic powder. In the laboratory the absorbed mercury was then released into a quartz-window cell by heating the tube in an oven at 500°C.

In this paper it is demonstrated that, by using extremely thin films of precipitated gold, quantitative recovery is obtained and memory effects, which result from the use of thicker films, are avoided.