Development of carbon paste electrode modified with cadmium ion-imprinted polymer for selective voltammetric determination of Cd2+

A simple and fast voltammetric method based on a new electrode composed of carbon paste electrode/bifunctional hybrid ion imprinted polymer (CPE/IIP) was developed for the quantification of Cd²⁺ in water samples. The voltammetric measurements by Differential Pulse Voltammetry were performed by using CPE containing 11.0 mg of IIP under phosphate buffer solution at concentration 0.1 mol L^?1 and pH 6.5. The electrochemical method was carried out by Cd²⁺ preconcentration at ?1.2 V during 210 s, followed by anodic stripping. The performance of IIP towards Cd²⁺ determination was evaluated by comparison to non-imprinted polymer, whose detectability of IIP was much higher (45%). The sensitivity of the sensor was found to be 0.0105 µA/µg L^?1. The limits of detection and limits of quantification were found to be 4.95 μg L^?1 and 16.4 μg L^?1, respectively. The developed method was successfully applied to Cd²⁺ determination in mineral, tap and lake water samples, whose results are in agreement with thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS) used as reference analytical technique. According to achieved results, the developed method can be used for routine analysis of quality control of water samples from different sources.     

Differential pulse voltammetric determination of trace rotenone using molecularly imprinted polymer microspheres

A new voltammetric method for the determination of rotenone is described. It is based on the reduction of an electroactive derivative of rotenone on the surface of an electrode. Rotenone in water was pre-concentrated using a new type of molecularly imprinted polymer microspheres and can react with hydrazine chloride to produce the electroactive derivative. The experimental conditions were discussed. Under optimum conditions, it was found that the peak potential (Ep) of the derivative of rotenone is ?1.02 V (vs. Ag/AgCl). Using the proposed procedure rotenone can be determined in the range 0.2–400 μg L^?1. The detection limit for rotenone is 0.1 μg L^?1 and the relative standard deviation for 100 μg L^?1 rotenone is 1.99 %. The method was applied to the determination of rotenone in water samples with satisfactory results.     

LC–MS Method for the Sensitive Determination of Metoclopramide: Application to Rabbit Plasma, Gel Formulations and Pharmaceuticals

To support real biological sample application, a simple, selective and rapid LC–MS method has been developed and validated for the sensitive determination of metoclopramide in rabbit blood, ex vivo permeation studies and pharmaceutical dosage form. LC–MS analysis was performed isocratically on a Zorbax SB-C₁₈ column with a mobile phase consisting of methanol:ammonium acetate buffer (pH 3.0) 75:25 (v/v) at a flow rate of 0.70 mL min^?1. The outlet of the column was connected to a single quadrupole mass spectrometer with positive mass spectrometric detection. Ions were detected in the positive multiple reaction monitoring mode. The assay was linear over the concentration range of 1.25–200 pg μL^?1 with a limit of detection of 0.077 pg μL^?1 for standard solutions and 2.5–200 pg μL^?1 with a limit of detection of 0.42 pg μL^?1 for serum samples. The method is applicable, covering a variety of pharmaceutical and biological studies. Metoclopramide was extracted from rabbit blood by liquid–liquid extraction using ether as the extraction solvent. The reproducibility of the method was found to be between 0.96 and 1.98 % (RSD) values. The proposed method has been extensively validated for the determination of metoclopramide in all working media. The sample preparations, flow rate and run time of the analytical systems are not time consuming. Moreover, for the stability of metoclopramide, the effect of temperature, UV light, H₂O₂, HCl and NaOH were also investigated.     

Analysis of eight pyrethroids in water samples by liquid–liquid microextraction based on solidification of floating organic droplet combined with gas chromatography

A novel method was developed for the determination of eight pyrethroids in water samples by liquid–liquid microextraction based on solidification of floating organic droplets followed by gas chromatography with electron capture detection. The type and volume of the extraction solvents, extraction time, sample solution temperature, stirring rate and ionic strength were studied and optimized. Under the optimum conditions, enrichment factors ranged from 824 to 1,432, and the limit of detection range from 2.0 to 50 ng?L^?1. The calibration graph is linear from 0.15 to 80 μg?L^?1 for cyfluthrin, fenvalerate, fluvalinate and deltamethrin, 0.09 to 80 μg?L^?1 for fenpropathrin, 0.006 to 80 μg?L^?1 for lambda-cyhalothrin, 0.026 to 80 μg?L^?1 for permethrin, 0.01 to 80 μg?L^?1 for cypermethrin. The correlation coefficients (r) varied from 0.9961 to 0.9988. The method was successfully applied to the determination of pyrethroid pesticide residues in tap water, well water, reservoir water, and river water. Recoveries ranged from 79.0% to 113.6%, and relative standard deviations are between 4.1% and 8.7%.     

Determination of Mycotoxins Using Hollow Fiber Dispersive Liquid–Liquid–Microextraction (HF-DLLME) Prior to High-Performance Liquid Chromatography – Tandem Mass Spectrometry (HPLC - MS/MS)

A modified hollow-fiber-supported dispersive liquid-liquid microextraction (HF-DLLME) method was developed for the determination of aflatoxins and ochratoxin A in food samples. The various parameters affecting the efficiency of extraction, such as pH, salt addition, extraction time, stirring rate, desorption time, type and volume of extractant and disperser solvents were carefully studied and optimized using two step strategies. The linearity of the evaluated results was 0.1 to 30?μg L^?1 for aflatoxins and 0.1 to 20?μg L^?1 for ochratoxin A, with regression coefficients (R²) exceeding 0.9990. The precision was satisfactory with relative standard deviation values less than 11%. The method accuracy was within the recommended range from 70% to 120% and analyte accuracy between 83% and 101%. The limits of detection and quantification were in the range from 0.04 to 0.06?μg L^?1 and 0.08 to 0.13?μg L^?1, respectively, for multi-aflatoxins, and 0.02 to 0.04?µg L^?1 and 0.08 to 0.10?µg L^?1, respectively, for ochratoxin A. The developed method was successfully applied for the determination of mycotoxins in food samples.     

Simple Determination of 4-Methylimidazole in Soft Drinks by Headspace SPME GC–MS

A simple method to detect 4-methylimidazole in soft drinks is described. This method is based on headspace solid-phase micro-extraction and gas chromatography–mass spectrometry (HS-SPME GC–MS). The HS-SPME parameters (selection of fiber, extraction temperature, heating time, and pH) were optimized and selected. Under the established condition, the detection and the quantification limit were 1.9 and 6.0 μg L^?1 using 4 mL of the liquid sample, respectively. The relative standard deviation for five independent determinations at 100.0 and 500.0 μg L^?1 was less than 8 %. The calibration curve was y = 0.6027x–0.0033 with a linearity of r ² = 0.997. Using the proposed method, the levels of 4-MEI were detected in a range from 94.0 to 324.8 μg L^?1. The comparison of liquid chromatography tandem mass spectrometry (LC–MS/MS) with the proposed method was performed and the agreement with LC–MS/MS for all samples was acceptable.     

Sensitive immunoassay for the β-agonist ractopamine based on glassy carbon electrode modified with gold nanoparticles and multi-walled carbon nanotubes in a film of poly-arginine

We are presenting an electrochemical immunosensor for the determination of the β-agonist and food additive ractopamine. A glassy carbon electrode (GCE) was modified with gold nanoparticles and a film of a composite made from poly(arginine) and multi-walled carbon nanotubes. Antibody against ractopamine was immobilized on the surface of the modified GCE which then was blocked with bovine serum albumin. The assembly of the immunosensor was followed by electrochemical impedance spectroscopy. Results demonstrated that the semicircle diameter increases, indicating that the film formed on the surface hinders electron transfer due to formation of the antibody-antigen complex on the modified electrode. Under optimal conditions, the peak current obtained by differential pulse voltammetry decreases linearly with increasing ractopamine concentrations in the 0.1 nmol?L^?1 to 1 μmol?L^?1 concentration range. The lower detection limit is 0.1 nmol?L^?1. The sensor displays good stability and reproducibility. The method was applied to the analysis of spiked swine feed samples and gave satisfactory results. Figure

Immunoassay for ractopamine based on glassy carbon electrode modified with gold nanoparticles and a film of a composite made from poly (arginine) and multi-walled carbon nanotubes was proposed. Under optimal conditions, the peak currents obtained by differential pulse voltammetry decreases linearly with increasing ractopamine concentrations in the 0.1 nmol?L^?1 to 1 μmol?L^?1 concentration range. The detection limit is 0.1 nmol?L^?1.     

Determination of Aroma Compounds from Alcoholic Beverages in Spiked Blood Samples by Means of Dynamic Headspace GC–MS

Some aroma compounds found in alcoholic beverages are characteristic of a certain beverage (i.e. 2,4-decadienoic acid ethyl ester is characteristic of pear spirit and 5-butyltetrahydro-4-methylfuran-2-on “whiskey lactone” is characteristic of aged spirits like whiskey). These substances were detectable in beverages but not in blood samples. The aim of this investigation was to find a sensitive sampling technique for aroma compounds in whole blood samples. This technique may be used in forensic toxicology for examination of drinking claims. The method comprises dynamic headspace sampling using a purge and trap concentrator, followed by quantitative gas chromatography–mass spectrometry (dynamic HS–GC–MS). The influence of sample preparation, trap adsorbents and sample temperature as well as desorption time and purge time on the quality of the analytical results were investigated. The following optimal parameters were determined: stirred and diluted whole blood sample without salt addition, use of Carbotrap C as trap material, sample temperature at 80 °C, desorption time 20 min and purge time 30 min. These optimal parameters were used for the determination of detection limits (LOD). The LOD of aroma compounds by means of dynamic headspace sampling were compared with the results of conventional sampling: the static headspace technique. Limits of detection for the aroma compounds with conventional static headspace GC are in the range 400–10,000 μg L^?1. Dynamic headspace–GC was found to be a more sensitive sampling technique for most of the aroma compounds investigated (e.g. C₄–C₈ ethyl esters, benzoic acid ethyl ester, linalool oxide and 4-ethylguaiacol) with detection limits between 1 and 50 μg L^?1, but there were also limits to the sampling of substances with lower volatility like decanoic acid ethyl ester, 2,4-decadienoic acid ethyl ester, eugenol and whiskey lactone with detection limits of about 1,000 μg L^?1.     

A magnetic metal-organic framework as a new sorbent for solid-phase extraction of copper(II), and its determination by electrothermal AAS

We report on the synthesis of Fe₃O₄-functionalized metal-organic framework (m-MOF) composite from Zn(II) and 2-aminoterephthalic acid by a hydrothermal reaction. The magnetic composite is iso-reticular and was characterized by FTIR, X-ray diffraction, SEM, magnetization, and TGA. The m-MOF was then applied as a sorbent for the solid-phase extraction of trace levels of copper ions with subsequent quantification by electrothermal AAS. The amount of sorbent applied, the pH of the sample solution, extraction time, eluent concentration and volume, and desorption time were optimized. Under the optimum conditions, the enrichment factor is 50, and the sorption capacity of the material is 2.4 mg g^?1. The calibration plot is linear over the 0.1 to 10 μg L^?1 Cu(II) concentration range, the relative standard deviation is 0.4 % at a level of 0.1 μg L^?1 (for n?=?10), and the detection limit is as low as 73 ng L^?1. We consider this magnetic MOF composite to be a promising and highly efficient material for the preconcentration of metal ions.

A SPE-LC-MS/MS Method for the Detection of Low Concentrations of Pharmaceuticals in Industrial Waste Streams

A SPE-LC-MS/MS method was developed and validated for the determination of three active pharmaceutical ingredients [API A (3-([2-(diaminomethyleneamino)thiazol-4-yl]methylthio)-N′-sulfamoyl propanimid amide, API B 5-[(2 R)-2-[2-(2-ethoxyphenoxy)ethylamino]propyl]-2-methoxybenzenesulfonamide hydrochloride, API C 1-azabicyclo[2.2.2]octan-8-yl (1S)-1-phenyl-3,4-dihydro-1H-isoquinoline-2-carboxylate] in the wastewater of a chemical synthesis production facility. The SPE-LC-MS/MS method was validated in actual influent and effluent samples. Linearity, LOD, LOQ, repeatability, intermediate precision, and recovery were determined. An LOQ of 400 μg · L^?1, 1.0 μg · L^?1, and 6 μg · L^?1, repeatability of 2.5% CV, 14.8% CV, and 11.9% CV, intermediate precision of 7.8% CV, 11.0% CV, and 8.7% CV and SPE recovery of 114%, 103%, and 91% was determined for API A, B, and C, respectively, in influent. An LOQ of 400 μg · L^?1, 0.8 μg · L^?1, and 6 μg · L^?1, repeatability of 2.0% CV, 11.0% CV, and 10.9% CV, intermediate precision of 1.7% CV, 6.8% CV, and 10.2% CV and SPE recovery of 116%, 96%, and 115% was established for API A, B, and C, respectively, in effluent. Coefficients of correlation for each analyte were >0.9301 confirming the linearity of the method. The LC-MS/MS method was used for an on-going monitoring program for these pharmaceuticals in wastewater. The method development techniques, validation procedures, and results from real wastewater samples are presented in this paper.     

Optimization of parameters for the alcoholic-assisted dispersive liquid–liquid microextraction of estrogens in water

Extraction and determination of estrogens in water samples were performed using alcoholic-assisted dispersive liquid–liquid microextraction (AA-DLLME) and high-performance liquid chromatography (UV/Vis detection). A Plackett–Burman design and a central composite design were applied to evaluate the AA-DLLME procedure. The effect of six parameters on extraction efficiency was investigated. The factors studied were volume of extraction and dispersive solvents, extraction time, pH, amount of salt and agitation rate. According to Plackett–Burman design results, the effective parameters were volume of extraction solvent and pH. Next, a central composite design was applied to obtain optimal condition. The optimized conditions were obtained at 220 μL 1-octanol as extraction solvent, 700 μL ethanol as dispersive solvent, pH 6 and 200 μL sample volume. Linearity was observed in the range of 1–500 μg L^?1 for E2 and 0.1–100 μg L^?1 for E1. Limits of detection were 0.1 μg L^?1 for E2 and 0.01 μg L^?1 for E1. The enrichment factors and extraction recoveries were 42.2, 46.4 and 80.4, 86.7, respectively. The relative standard deviations for determination of estrogens in water were in the range of 3.9–7.2 % (n = 3). The developed method was successfully applied for the determination of estrogens in environmental water samples.     

Sensitive electrochemical detection of picloram utilising a multi-walled carbon nanotube/Cr-based metal-organic framework composite-modified glassy carbon electrode

This study describes the utilisation of a glassy carbon electrode modified with a composite of multi-walled carbon nanotube and Cr-based metal-organic framework (MIL-101, Cr-BDC, BDC = 1,4-benzenedicarboxylate) for the sensitive, simple and fast voltammetric determination of picloram in environmental samples. Under optimum conditions, additions of picloram using square wave voltammetry showed linear ranges of picloram concentrations from 24.15 to 3018 µg?L^?1 (0.1–12.5 μM) and from 3018 to 9658 µg?L^?1 (12.5–40 μM) with a detection limit of 14.49 µg?L^?1 (0.06 µM). The method was successfully applied to the determination of picloram in tap and river water samples spiked with picloram without any purification step by the standard addition method. The good recovery values obtained ranging from 97.5% to 105.0% revealed the reliability and accuracy of the method.     

Sensitive Analysis of Malondialdehyde in Human Urine by Derivatization with Pentafluorophenylhydrazine then Headspace GC–MS

A sensitive method based on derivatization with pentafluorophenylhydrazine then headspace gas chromatography–mass spectrometry has been used for analysis of malondialdehyde in human urine. Preparation of urine sample by one-step derivatization/evaporation was performed by reaction of malondialdehyde with pentafluorophenylhydrazine in a headspace vial for 10 min; the derivatives were then injected in GC–MS analysis. The reaction was performed at pH 3, and total analysis time was 35 min. The method detection limit was 0.04 μg L^?1. For MDA concentrations of 2.0 and 10.0 μg L^?1 the relative standard deviation was less then 5%. The concentration of MDA in urine was measured to be 0.199 ± 0.252 μmol g^?1 creatinine (0.022 ± 0.028 μmol mmol^?1 creatinine).     

Determination of cadmium, chromium and copper in high salt samples by LA-ICP-OES after electrodeposition—preliminary study

A novel method is presented for determination of heavy metal ions in a high-saline matrix. It is based on the electrodeposition of the ions and subsequent laser ablation coupled to inductively coupled plasma optical emission spectrometry (LA-ICP-OES). Three arrangements for electrodeposition were worked out, two of them with stationary working electrodes. Materials for use in the working electrodes, and conditions for electrodeposition of Cd, Cr and Cu (pH, deposition current, time of electrolysis) were studied. Nickel was found to be the best electrode material. The metals accumulate on the surface of electrode and were then evaporated/ablated with a Nd:YAG laser focused into the ICP-OES spectrometer. The detection limits are 0.13 mg?L^?1 for Cd, 0.15 mg?L^?1 for Cu, and 1.9 mg?L^?1 for Cr in case of a stationary bottom working electrode, and 0.25 mg?L^?1 for Cd, 0.05 mg?L^?1 for Cu, 0.8 mg?L^?1 for Cr when using a rotating electrode. The relative standard deviation is in range from 3.8 to 10.3%. Waste water was analyzed in this way by the standard addition method.     

Piper nigrum: Micropropagation, Antioxidative enzyme activities, and Chromatographic Fingerprint Analysis for Quality Control

A reliable in vitro regeneration system for the economical and medicinally important Piper nigrum L. has been established. Callus and shoot regeneration was encouraged from leaf portions on Murashige and Skoog (MS) medium augmented with varied concentrations of plant growth regulators. A higher callus production (90 %) was observed in explants incubated on MS medium incorporated with 1.0 mg?L^?1 6-benzyladenine (BA) along with 0.5 mg?L^?1 gibberellic acid after 4 weeks of culture. Moreover, a callogenic response of 85 % was also recorded for 1.0 mg?L^?1 BA in combination with 0.25 mg?L^?1 α-naphthalene acetic acid (NAA) and 0.25 mg?L^?1 2,4-dichlorophenoxyacetic acid or 0.5 mg?L^?1 indole butyric acid (IBA) along with 0.25 mg?L^?1 NAA and indole acetic acid. Subsequent sub-culturing of callus after 4 weeks of culture onto MS medium supplemented with 1.5 mg?L^?1 thiodiazoran or 1.5 mg?L^?1 IBA induced 100 % shoot response. Rooted plantlets were achieved on medium containing varied concentrations of auxins. The antioxidative enzyme activities [superoxide dismutase (SOD), peroxidase (POD), catalase (CAT), and ascorbate peroxidase (APX)] revealed that significantly higher SOD was observed in regenerated plantlets than in other tissues. However, POD, CAT, and APX were higher in callus than in other tissues. A high-performance liquid chromatography (HPLC) fingerprint analysis protocol was established for quality control in different in vitro-regenerated tissues of P. nigrum L. During analysis, most of the common peaks represent the active principle “piperine.” The chemical contents, especially piperine, showed variation from callus culture to whole plantlet regeneration. Based on the deviation in chromatographic peaks, the in vitro-regenerated plantlets exhibit a nearly similar piperine profile to acclimated plantlets. The in vitro regeneration system and HPLC fingerprint analysis established here brought a novel approach to the quality control of in vitro plantlets, producing metabolites of interest with substantial applications for the conservation of germplasm.     

Voltammetric sensor based on magnetic particles modified composite electrode for determination of triamterene in biological sample

Some diuretic substances are controlled and monitored by the World Anti-Doping Agency as prohibited substances for use by athletes, such as triamterene (TRT). Thus, this work describes a voltammetric method based on graphite-epoxy composite electrode modified by tosyl-functionalized magnetic particles (GECE/MPs-To) for determination of TRT diuretic in urine sample. The TRT presented an oxidation peak at +1.24 V at GECE/MPs-To with irreversible behavior. Controlled potential electrolysis of the TRT at +1.26 V indicated the two electrons are transferred during amine group oxidation and the main product was identified by LC-MS/MS. The anodic peak current is 25 % higher at the modified electrode, suggesting that TRT is adsorbed on the magnetic particles. Using optimized conditions by using multivariate optimization of the parameters inherent of the square wave voltammetry, a calibration curve was constructed with a linear relationship for TRT from 0.500 to 99.8 μmol L^?1. The limits of detection and quantification were 1.47 and 4.91?×?10^?7 mol L^?1, respectively. The proposed method was applied to urine sample and validated by LC-MS/MS technique where the values found and compared between the two techniques showed no significant difference at 95 % confidence.     

Ionic liquid-based headspace single-drop microextraction coupled to gas chromatography for the determination of chlorobenzene derivatives

A novel method, based on the coupling of ionic liquid-based headspace single-drop microextraction (SDME) with gas chromatography (GC), is developed for the determination of chlorobenzene derivatives. For the SDME of five chlorobenzene derivatives, a 1.0 μL 1-octyl-3-methylimidazolium hexafluorophosphate microdrop is exposed for 20 min to the headspace of a 15 ml aqueous sample containing 20% (w/v) NaCl placed in 25 ml vial at 40 °C. Then, the extractant is directly injected into the injector block of the GC instrument. To avoid ionic liquid leaking into the chromatographic column, a small glass tube is placed in the injection block. Under optimized operation conditions, linear relation between peak areas and analyte concentrations up to 1.5 mg L^?1 has been obtained The detection limits range from 0.1 to 0.5 μg L^?1 for the various analytes. The relative standard deviations at 1.0 μg L^?1 range from 7.7 to 12.4%, and the enrichment factors from 41 to 127. The method is simple and sensitive, and does not suffer from the influence of a solvent peak. Its applicability is demonstrated by the determination of chlorobenzenes in wastewater samples.     

Determination of neptunium in a reprocessing plant by an on-line solid-phase extraction/electrochemical detection system

In this study, a flow-based electrochemical detection system coupled to a solid-phase extraction column was developed for the determination of neptunium in the presence of Pu(IV). Np(V) in the sample solution was completely oxidized to Np(VI) via electrolysis using a column electrode composed of carbon fibers. The column electrode effluent was then loaded onto a TEVA^® column, and subsequently onto a UTEVA^® column using 3 mol L^?1 HNO₃. Pu(IV) was retained on the TEVA column and separated from Np(VI), while Np(VI) was retained on the UTEVA column. Np(VI) was eluted from the UTEVA column with 0.01 mol L^?1 HNO₃ and then introduced directly into a flow-through electrolysis cell. An electrochemical amperometric method with a working potential of +0.1 V (vs. Ag/AgCl) was used to detect Np(VI). The current produced due to the reduction of Np(VI) was continuously monitored and recorded, and the Np concentration was calculated from the peak area. The relative standard deviation of 10 analyses was 2.4 % for an Np solution (0.50 mg L^?1) containing 1.0 μg Np. The detection limit, which was determined to be three times the standard deviation, was 35 μg L^?1 (70 ng Np).     

Multiresidue Analysis of Pesticides in Vegetables and Citrus Fruits by LC–MS–MS

In this work, an analytical multiresidue method using liquid chromatography tandem-mass spectrometry (LC–MS–MS) with triple quadrupole in selected reaction monitoring (SRM) mode for the simultaneous determination of 54 pesticides in vegetables (pepper and tomato) and citrus fruits (orange and lemon) has been developed. The procedure involves initial single phase extraction of sample with acetonitrile by agitation, followed by liquid–liquid partition aided by “salting out” process using NaCl. The average recovery by the LC–MS–MS method obtained for these compounds varied from 65.5 to 114.5% with a relative standard deviation between 2.3 and 8.3%. The method presents good linearity over the range assayed 10–500 μg L^?1 (except famoxadone 50–1,000 μg L^?1) and the detection limits for the pesticides studied varied from 0.03 to 14.9 μg kg^?1. The proposed method was used to determine pesticide levels in vegetables and citrus fruit samples from different experimental orchards and greenhouses from the Region of Murcia.     

Sensitive Analysis of Wilforidine in Human Plasma by LC-APCI-MS/MS

Wilforidine is a potentially efficient medicine to cure autoimmune diseases. In this paper, a sensitive and selective liquid chromatographic method coupled with atmospheric -pressure chemical ionization mass spectrometry (LC–APCI–MS/MS) has been developed for quantification of wilforidine in human plasma. Samples were deproteinized with acetonitrile and cleaned by solid-phase extraction. The chromatographic separation was performed on an analytical RRHD C₁₈ column (50 × 2.1 mm) using ammonium acetate solution (10.0 mmol L^?1)/acetonitrile (30/70, v/v) as the mobile phase at a flow rate of 0.7 mL min^?1. Detection was carried out by the positive multiple reaction monitoring mode with transitions of m/z 780 → 684 for wilforidine, and 646 → 586 for aconitine (internal standard), respectively. The calibration curve was linear (r = 0.9991) in the concentration range of 0.5–100.0 μg L^?1 with a lower limit of quantification of 0.5 μg L^?1 in plasma. Intra- and inter-day relative standard deviations were less than 6.8 and 13.1 %, respectively, and the recoveries were between 88.0 and 96.0 %. This accurate and highly specific assay provides a useful method for evaluating the pharmacokinetics of wilforidine in human plasma.