Palladium monolayer and palladium alloy electrocatalysts for oxygen reduction

We investigated the oxygen-reduction reaction (ORR) on Pd monolayers on various surfaces and on Pd alloys to obtain a substitute for Pt and to elucidate the origin of their activity. The activity of Pd monolayers supported on Ru(0001), Rh(111), Ir(111), Pt(111), and Au(111) increased in the following order: Pd/Ru(0001) < Pd/Ir(111) < Pd/Rh(111) < Pd/Au(111) < Pd/Pt(111). Their activity was correlated with their d-band centers, which were calculated using density functional theory (DFT). We found a volcano-type dependence of activity on the energy of the d-band center of Pd monolayers, with Pd/Pt(111) at the top of the curve. The activity of the non-Pt Pd2Co/C alloy electrocatalyst nanoparticles that we synthesized was comparable to that of commercial Pt-containing catalysts. The kinetics of the ORR on this electrocatalyst predominantly involves a four-electron step reduction with the first electron transfer being the rate-determining step. The downshift of the d-band center of the Pd "skin", which constitutes the alloy surface due to the strong surface segregation of Pd at elevated temperatures, determined its high ORR activity. Additionally, it showed very high methanol tolerance, retaining very high catalytic activity for the ORR at high concentrations of methanol. Provided its stability is satisfactory, this catalyst might possibly replace Pt in fuel-cell cathodes, especially those of direct methanol oxidation fuel cells (DMFCs).     

A first principles study of oxygen reduction reaction on a Pt(111) surface modified by a subsurface transition metal M (M = Ni, Co, or Fe)

We have performed first-principle density functional theory calculations to investigate how a subsurface transition metal M (M = Ni, Co, or Fe) affects the energetics and mechanisms of oxygen reduction reaction (ORR) on the outermost Pt mono-surface layer of Pt/M(111) surfaces. In this work, we found that the subsurface Ni, Co, and Fe could down-shift the d-band center of the Pt surface layer and thus weaken the binding of chemical species to the Pt/M(111) surface. Moreover, the subsurface Ni, Co, and Fe could modify the heat of reaction and activation energy of various elementary reactions of ORR on these Pt/M(111) surfaces. Our DFT results revealed that, due to the influence of the subsurface Ni, Co, and Fe, ORR would adopt a hydrogen peroxide dissociation mechanism with an activation energy of 0.15 eV on Pt/Ni(111), 0.17 eV on Pt/Co(111), and 0.16 eV on Pt/Fe(111) surface, respectively, for their rate-determining O2 protonation reaction. In contrast, ORR would follow a peroxyl dissociation mechanism on a pure Pt(111) surface with an activation energy of 0.79 eV for its rate-determining O protonation reaction. Thus, our theoretical study explained why the subsurface Ni, Co, and Fe could lead to multi-fold enhancement in catalytic activity for ORR on the Pt mono-surface layer of Pt/M(111) surfaces.     

First-principles analysis of the effects of alloying Pd with Ag for the catalytic hydrogenation of acetylene-ethylene mixtures

The effect of alloying Pd with Ag on the hydrogenation of acetylene is examined by analyzing the chemisorption of all potential C(1) (atomic carbon, CH, methylene, and methyl) and C(2) (acetylene, vinyl, ethylene, ethyl, ethane, ethylidene, ethylidyne, and vinylidene) surface intermediates and atomic hydrogen along with the reaction energies for the elementary steps that produce these intermediates over Pd(111), Pd(75%)Ag(25%)/Pd(111), Pd(50%)Ag(50%)/Pd(111), and Ag(111) surfaces by using first-principle density functional theoretical (DFT) calculations. All of the calculations reported herein were performed at 25% surface coverage. The adsorption energies for all of the C(1) and C(2) intermediates decreased upon increasing the composition of Ag in the surface. Both geometric as well as electronic factors are responsible for the decreased adsorption strength. The modes of adsorption as well as the strengths of adsorption over the alloy surfaces in a number of cases were characteristically different than those found over pure Pd (111) and Ag (111). Adsorbates tend to minimize their interaction with the Ag atoms in the alloy surface. An electronic analysis of these surfaces shows that there is, in general, a shift in the occupied d-band states away from the Fermi level when Pd is alloyed with Ag. The s and p states also appear to contribute and may be responsible for small deviations from the Hammer-N?rskov model. The effect of alloying is more pronounced on the calculated reaction energies for different possible surface elementary reactions. Alloying Pd with Ag reduces the exothermicity (increases endothermicity) for bond-breaking reactions. This is consistent with experimental results that show a decrease in the decomposition products in moving from pure Pd to Pd-Ag alloys.(2-5) In addition, alloying increases the exothermicity of bond-forming reactions. Alloying therefore not only helps to suppress the unfavorable decomposition (bond-breaking) reaction rates but also helps to enhance the favorable hydrogenation (bond-forming) reaction rates.     

Comparative theoretical study of formaldehyde decomposition on PdZn, Cu, and Pd surfaces

Methanol steam reforming, catalyzed by Pd/ZnO (PdZn alloy), is a potential source of hydrogen for on-board fuel cells. CO has been reported to be a minor side product of methanol decomposition that occurs in parallel to methanol steam reforming on PdZn catalysts. However, fuel cells currently used in vehicles are very sensitive to CO poisoning. To contribute to the understanding of pertinent reaction mechanisms, we employed density functional slab model calculations to study the decomposition of formaldehyde, a key intermediate in methanol decomposition and steam reforming reactions, on planar surfaces of Pd, Cu, and PdZn as well as on a stepped surface of PdZn. The calculated activation energies indicate that dehydrogenation of formaldehyde is favorable on Pd(111), but unfavorable on Cu(111) and PdZn(111). On the stepped PdZn(221) surface, the dehydrogenation process was calculated to be more competitive to formaldehyde desorption than on PdZn(111). Thus, we ascribe the experimentally observed small amount of CO, formed during steam reforming of methanol on the Pd/ZnO catalyst, to occur at metallic Pd species of the catalyst or at defect sites of PdZn alloy.     

氢和硫原子在Pd、Au和Cu及PdAu、PdCu合金(111)表面吸附的密度泛函研究

用密度泛函理论研究了氢和硫原子在金属Pd、Au、Cu以及合金PdM3、Pd2M2 和Pd3M(111)表面的吸附(M=Au, Cu), 得到了覆盖率为0.25时最稳定的吸附位、结合能以及吸附前后表面的驰豫情况. 结果表明, 氢和硫均与Pd形成最稳定的吸附, Cu次之, Au的吸附最弱, 其在三种纯金属(111)表面的最稳定吸附位均为fcc位. 由于PdAu合金具有较大的晶格常数, Pd3Au 合金吸附氢的结合能甚至较纯Pd更大, 除此之外, 氢和硫在PdM合金表面的吸附基本随M组分的增加而减弱, 而最稳定的吸附位随金属种类和组成变化而变化. 根据计算得到的吸附结合能, 发现与PdCu合金相比, PdAu合金在Au含量较低(约25%, 摩尔分数)时, 氢和硫吸附的结合能下降较慢, 而Au含量较高(跃50%)时, 结合能迅速下降, 这表明含金量为25%-50%的PdAu合金有可能在保持相近透氢性能的同时, 比PdCu合金具有更好的抗硫毒性.     

Thermodynamic guidelines for the design of bimetallic catalysts for oxygen electroreduction and rapid screening by scanning electrochemical microscopy. M-co (M: Pd, Ag, Au)

We propose guidelines for the design of improved bimetallic (and related) electrocatalysts for the oxygen reduction reaction (ORR) in acidic media. This guide is based on simple thermodynamic principles assuming a simple mechanism where one metal breaks the oxygen-oxygen bond of molecular O(2) and the other metal acts to reduce the resulting adsorbed atomic oxygen. Analysis of the Gibbs free energies of these two reactions guides the selection of combinations of metals that can produce alloy surfaces with enhanced activity for the ORR when compared to the constituent metals. Selected systems have been tested by fabricating arrays of metallic catalysts consisting of various binary and ternary combinations of Pd, Au, Ag, and Co deposited on glassy carbon (GC) substrates. The electrocatalytic activity of these materials for the ORR in acidic medium was examined using scanning electrochemical microscopy (SECM) in a new rapid-imaging mode. This was used to rapidly screen arrays covering a wide range of catalyst compositions for their activity for the ORR in 0.5 M H(2)SO(4). Using the SECM technique, we have identified combinations of metals with enhanced electrocatalytic activities when compared with the constituent, pure metals. Addition of Co to Pd, Au, and Ag clearly decreases the ORR overpotential, in agreement with the proposed model. Catalyst spots that exhibited enhanced electrocatalytic activity in the SECM screening technique were then examined using classical rotating disk electrode (RDE) experiments. The activity of carbon black supported catalyst mixtures on a GC RDE and the electrocatalytic activity determined using the SECM screening technique showed excellent agreement. C/Pd-Co electrodes (10-30% Co) exhibited remarkable activity for ORR catalysis, close to that of carbon-supported Pt.     

Theoretical Modelling and Facile Synthesis of a Highly Active Boron‐Doped Palladium Catalyst for the Oxygen Reduction Reaction

A highly active alternative to Pt electrocatalysts for the oxygen reduction reaction (ORR), which is the cathode‐electrode reaction of fuel cells, is sought for higher fuel‐cell performance. Our theoretical modelling reveals that B‐doped Pd (Pd‐B) weakens the absorption of ORR intermediates with nearly optimal binding energy by lowering the barrier associated with O₂ dissociation, suggesting Pd‐B should be highly active for ORR. In fact, Pd‐B, facile synthesized by an electroless deposition process, exhibits 2.2 times and 8.8 times higher specific activity and 14 times and 35 times less costly than commercial pure Pd and Pt catalysts, respectively. Another computational result is that the surface core level of Pd is negatively shifted by B doping, as confirmed by XPS, and implies that filling the density of states related to the anti‐bonding of oxygen to Pd surfaces with excess electrons from B doping, weakens the O bonding to Pd and boosts the catalytic activity.     

Zn modification of the reactivity of Pd(111) toward methanol and formaldehyde

The adsorption and reaction of methanol and formaldehyde on two-dimensional PdZn alloys on a Pd(111) surface were studied as a function of the Zn content in the alloy in order to understand the role of Zn in Pd/ZnO catalysts for the steam reforming of methanol (SRM). Temperature programmed desorption (TPD) and high resolution electron energy loss spectroscopy (HREELS) data show that Zn atoms incorporated into the Pd(111) surface dramatically decrease the dehydrogenation activity and alter the preferred bonding sites for adsorbed CO, CH3O, and CH2O intermediates. The experimental results obtained in this study are consistent with previous theoretical studies of this system and provide new insight into how Zn alters the reactivity of Pd.     

Single-Atom Alloys for the Electrochemical Oxygen Reduction Reaction

Single-atom alloys (SAAs) consisting of isolated transition-metal atoms doped in the surface of coinage metal hosts exhibit unique catalytic properties, harnessing the high activity of the dopant metals with the selectivity of the coinage metal hosts. Here we use density functional theory (DFT) to study SAAs comprised of Ni, Pd, Pt, Co and Rh doped into Ag and Au hosts, as candidate electrocatalysts for the oxygen reduction reaction (ORR) in proton-exchange membrane (PEM) fuel-cells. Our calculations reveal that the PdAu SAA exhibits a slightly lower theoretical overpotential, enhanced selectivity for 4-e⁻ ORR, and tolerance to CO-poisoning compared to Pt(111). While the number of active sites of PdAu SAA is lower than that of Pt(111), the aforementioned desirable properties could bring the overall catalytic performance thereof close to that of Pt/C, indicating that the PdAu SAA could be a viable material for electrocatalytic ORR in PEM fuel-cells.     

Pd(111), Pd(100)及Pd(110)表面H2和O2直接合成H2O2的密度泛函理论研究

采用周期性密度泛函理论研究了H₂和O₂在Pd(111),Pd(100)及Pd(110)表面上直接合成H₂O₂的反应机理,对反应的主要基元步骤进行了计算和分析.结果表明,Pd(111)表面对H₂O₂直接合成的催化选择性最好,表面原子密度较低的Pd(100)表面和Pd(110)表面上含有O-O键的表面物种解离严重,不利于H₂O₂的生成.H₂O₂的选择性与含有O-O键表面物种的O-O键能和表面物种的结合能有关.含有O-O键的表面物种在表面的结合能越大,越容易发生解离,不利于形成H₂O₂.     

Atomic ensemble and electronic effects in Ag-rich AgPd nanoalloy catalysts for oxygen reduction in alkaline media

The ability to design and characterize uniform, bimetallic alloy nanoparticles, where the less active metal enhances the activity of the more active metal, would be of broad interest in catalysis. Herein, we demonstrate that simultaneous reduction of Ag and Pd precursors provides uniform, Ag-rich AgPd alloy nanoparticles (~5 nm) with high activities for the oxygen reduction reaction (ORR) in alkaline media. The particles are crystalline and uniformly alloyed, as shown by X-ray diffraction and probe corrected scanning transmission electron microscopy. The ORR mass activity per total metal was 60% higher for the AgPd(2) alloy relative to pure Pd. The mass activities were 2.7 and 3.2 times higher for Ag(9)Pd (340 mA/mg(metal)) and Ag(4)Pd (598 mA/mg(metal)), respectively, than those expected for a linear combination of mass activities of Ag (60 mA/mg(Ag)) and Pd (799 mA/mg(Pd)) particles, based on rotating disk voltammetry. Moreover, these synergy factors reached 5-fold on a Pd mass basis. For silver-rich alloys (Ag(≥4)Pd), the particle surface is shown to contain single Pd atoms surrounded by Ag from cyclic voltammetry and CO stripping measurements. This morphology is favorable for the high activity through a combination of modified electronic structure, as shown by XPS, and ensemble effects, which facilitate the steps of oxygen bond breaking and desorption for the ORR. This concept of tuning the heteroatomic interactions on the surface of small nanoparticles with low concentrations of precious metals for high synergy in catalytic activity may be expected to be applicable to a wide variety of nanoalloys.     

NO Chemisorption on Pt(111), Rh/Pt(111), and Pd/Pt(111)

The chemisorption of NO on clean Pt(111), Rh/Pt(111) alloy, and Pd/Pt(111) alloy surfaces has been studied by first principles density functional theory (DFT) computations. It was found that the surface compositions of the surface alloys have very different effects on the adsorption of NO on Rh/Pt(111) versus that on Pd/Pt(111). This is due to the different bond strength between the two metals in each alloy system. A complex d-band center weighting model developed by authors in a previous study for SO2 adsorption is demonstrated to be necessary for quantifying NO adsorption on Pd/Pt(111). A strong linear relationship between the weighted positions of the d states of the surfaces and the molecular NO adsorption energies shows the closer the weighted d-band center is shifted to the Fermi energy level, the stronger the adsorption of NO will be. The consequences of this study for the optimized design of three-way automotive catalysts, (TWC) are also discussed.     

Pt‐Pd‐Co Trimetallic Alloy Network Nanostructures with Superior Electrocatalytic Activity towards the Oxygen Reduction Reaction

Pt alloy nanostructures show great promise as electrocatalysts for the oxygen reduction reaction (ORR) in fuel cell cathodes. Herein, three‐dimensional (3D) Pt‐Pd‐Co trimetallic network nanostructures (TNNs) with a high degree of alloying are synthesized through a room temperature wet chemical synthetic method by using K₂PtCl₄/K₃Co(CN)₆–K₂PdCl₄/K₃Co(CN)₆ mixed cyanogels as the reaction precursor in the absence of surfactants and templates. The size, morphology, and surface composition of the Pt‐Pd‐Co TNNs are investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), selected‐area electron diffraction (SAED), energy dispersive spectroscopy (EDS), EDS mapping, X‐ray diffraction (XRD), and X‐ray photoelectron spectroscopy (XPS). The 3D backbone structure, solid nature, and trimetallic properties of the mixed cyanogels are responsible for the 3D structure and high degree of alloying of the as‐prepared products. Compared with commercially available Pt black, the Pt‐Pd‐Co TNNs exhibit superior electrocatalytic activity and stability towards the ORR, which is ascribed to their unique 3D structure, low hydroxyl surface coverage and alloy properties.     

Microkinetic Modeling of Ethane Hydrogenolysis on Metals

The microkinetic analysis of ethane hydrogenolysis in the framework of the Sinfelt-Taylor mechanism is carried out using UBI-QEP data on the energetics of elementary steps. On single-crystalline surfaces of Pd(111), Pt(111), and Ni(111), the reaction predominantly occurs via ethyl formation in which the C-C bond is cleaved. The surface concentration of ethylidyne is very low, and ethyl has the highest concentration among all hydrocarbon fragments. For the conditions studied in this work, the activity in ethane hydrogenolysis increases in the series Pd(111) < Pt(111) < Ni(111). According to the results of kinetic modeling, the reaction occurs via quasi-equilibrium steps of adsorption and dissociation of hydrogen and ethane and further, practically irreversible formation of methane.     

CO2在金属表面活化的能学方法研究

应用UBI-QEP方法, 估算了CO2-在金属表面的吸附热, 并计算了CO2在Cu(111)、Pd(111)、Fe(111)、Ni(111)表面的各种反应途径的活化能垒. 结果表明, CO2-在4种过渡金属表面相对的稳定性和CO2解离吸附的活性顺序一致,均为Fe>Ni>Cu>Pd. 说明CO2-可能是CO2解离吸附的关键中间体. 在Cu、Pd、Ni表面上, CO2解离吸附的最终产物是CO,而在Fe表面其最终会解离成C和O. 在Cu、Fe、Ni表面, CO2加氢活化是一种有效模式, 而在Pd上则不容易进行. 在Cu和Pd表面,碳酸盐物种也可能是CO2活化的重要中间体.     

部分氧化碳化硅提高钯催化氧还原反应性能

燃料电池具有能量转换效率高的优点,是能量转换与储存的高效器件之一.目前,燃料电池阴极氧还原反应(ORR)动力学缓慢,并且催化ORR大量使用铂碳(Pt/C)催化剂,由于Pt储量少,价格高,载体碳材料易发生碳蚀导致催化剂稳定性降低,限制了其进一步商业化应用.钯(Pd)与Pt为同族元素,具有相似的电子结构和化学性质,其储量是Pt的50倍,同时,Pd具有良好的抗甲醇毒性和抗一氧化碳毒性,因此,被视为燃料电池中阴极Pt催化剂的潜在替代品.但商用Pd/C催化剂的ORR活性较Pt/C差,因此,大量的研究工作集中在提高Pd基ORR催化剂的活性方面:将Pd与具有3d轨道的金属形成合金或将Pd负载到不同的载体上.通过选择合适的载体影响Pd的电子结构,从而提高催化剂活性和稳定性,是一种较简单的、有利于规模化生产Pd基ORR催化剂的方法.碳化硅(SiC)具有良好的电化学稳定性、热稳定性、机械强度和较强的供电子能力,可被用作ORR的金属催化剂载体.然而,由于金属与SiC作用较弱,需要制备特殊形貌的SiC或将SiC表面改性;通常,这些SiC基载体的制备过程复杂并且成本高.而在有氧条件下制备、保存或使用SiC时,其表面不可避免地被氧化,这种在温和条件下生成的表面具有含氧官能团的SiC,由于制备过程简便,可以大规模生产,且与金属有强的相互作用,是一种很有前景的ORR的Pd基催化剂载体.对于用于替代Pt基催化剂的负载型Pd基ORR催化剂的开发和大规模制造来说,对载体表面改性的深入了解是一个重要并且具有挑战性的课题.目前尚未发现关于SiC表面的含氧基团对ORR性能影响的报道.因此,详细考察SiC载体上含氧基团在ORR中的作用对于理解、设计和开发具有优异ORR性能的SiC负载催化剂至关重要.本文采用沉积沉淀法在表面部分氧化的碳化硅(O-SiC)均匀负载了平均直径为5.2 nm的Pd纳米颗粒.与20 wt%商业Pt/C相比,制备的2.5 wt%Pd/O-SiC催化剂显示出较好的ORR活性(半波电位正向移动10 mV),较好的稳定性(10 h后,电流密度损失3.5%vs.34.9%),和较高的抗甲醇毒性.结构表征及密度泛函理论(DFT)计算结果表明,与Pd/C相比,Pd/O-SiC具有优异的ORR性能主要是由于O-SiC载体对Pd纳米颗粒具有电子调控作用,使Pd带负电.富电子Pd增强了ORR关键中间体OOH的吸附,降低了反应的吉布斯自由能,从而提高了ORR活性.另外,O-SiC载体对Pd纳米颗粒具有大的结合能和较好的SiC稳定性,增强了Pd/O-SiC催化剂的抗甲醇毒性及稳定性.DFT计算结果表明,SiC表面部分氧化后,仍保持对Pd的较高结合能,同时大幅增强了催化剂对中间体的吸附,降低了ORR关键电化学步骤吉布斯自由能,从而提高了氧还原性能.因此,本工作明确了SiC表面氧化的作用,同时提供了一种简易大规模制备高效负载型铂基替代ORR催化剂的策略.     

Experimental and theoretical investigation of the stability of Pt-3d-Pt(111) bimetallic surfaces under oxygen environment

The stability of the Pt-3d-Pt(111) (3d = Ti, V, Cr, Mn, Fe, Co, or Ni) bimetallic surface structures in the presence of adsorbed oxygen has been investigated by means of density functional theory (DFT). The dissociative binding energies of oxygen on Pt-3d-Pt(111) (i.e., subsurface 3d monolayer) and 3d-Pt-Pt(111) (i.e., surface 3d monolayer) were calculated. All of the Pt-3d-Pt(111) surfaces were found to have weaker oxygen binding energies than pure Pt(111) whereas all of the 3d-Pt-Pt(111) surfaces were found to have stronger oxygen binding energies than pure Pt(111). The total heat of reaction was calculated for the segregation for 3d metal atoms from Pt-3d-Pt(111) to 3d-Pt-Pt(111) when exposed to a half monolayer of oxygen. All of the Pt-3d-Pt(111) subsurface structures were predicted to be thermodynamically unstable with adsorbed oxygen. In addition, the segregation of subsurface Ni and Co to the surfaces of Pt-Ni-Pt(111) and Pt-Co-Pt(111) was investigated experimentally using Auger electron spectroscopy (AES) and high-resolution electron energy loss spectroscopy (HREELS). AES and HREELS confirmed the trend predicted by DFT modeling and showed that both the Pt-Ni-Pt(111) and Pt-Co-Pt(111) surface structures were unstable in the presence of adsorbed oxygen. The activation barrier of the segregation of surbsurface Ni and Co atoms was determined to be 15 +/- 2 and 7 +/- 1 kcal/mol, respectively. These results are further discussed for their implication in the design and selection of cathode bimetallic electrocatalysts for the oxygen reduction reaction (ORR) in polymer electrode membrane (PEM) fuel cells.     

Acetate coverage effect on the reactivity of vinyl acetate synthesis on Pd/Au alloy surfaces

Vinyl acetate (VA) synthesis on Pd/Au(111) and Pd/Au(100) surfaces has been systematically investigated through first-principles density functional theory (DFT) calculations. The DFT results showed that for VA synthesis, the ‘Samanos’ reaction mechanism (i.e., direct coupling of coadsorbed ethylene and acetate species and subsequent β-hydride elimination to form VA) is more favorable than the ‘Moiseev’ mechanism (i.e., ethylene first dehydrogenates to form vinyl species which then couple with the coadsorbed acetate species to form VA). More importantly, it was found the surface coverage of acetate has a significant effect on the reactivity of VA synthesis, and the activation energy of the rate-controlling step on Pd/Au(100) surface is smaller than that on Pd/Au(111) surface (0.88 vs. 0.95 eV), indicating the former is more active than the latter.     

A theoretical study of surface reduction mechanisms of CeO(2)(111) and (110) by H(2).

Reaction mechanisms for the interactions between CeO(2)(111) and (110) surfaces are investigated using periodic density functional theory (DFT) calculations. Both standard DFT and DFT+U calculations to examine the effect of the localization of Ce 4f states on the redox chemistry of H(2)-CeO(2) interactions are described. For mechanistic studies, molecular and dissociative local minima are initially located by placing an H(2) molecule at various active sites of the CeO(2) surfaces. The binding energies of physisorbed species optimized using the DFT and DFT+U methods are very weak. The dissociative adsorption reactions producing hydroxylated surfaces are all exothermic; exothermicities at the DFT level range from 4.1 kcal mol(-1) for the (111) to 26.5 kcal mol(-1) for the (110) surface, while those at the DFT+U level are between 65.0 kcal mol(-1) for the (111) and 81.8 kcal mol(-1) for the (110) surface. Predicted vibrational frequencies of adsorbed OH and H(2)O species on the surfaces are in line with available experimental and theoretical results. Potential energy profiles are constructed by connecting molecularly adsorbed and dissociatively adsorbed intermediates on each CeO(2) surface with tight transition states using the nudged elastic band (NEB) method. It is found that the U correction method plays a significant role in energetics, especially for the intermediates of the exit channels and products that are partially reduced. The surface reduction reaction on CeO(2)(110) is energetically much more favorable. Accordingly, oxygen vacancies are more easily formed on the (110) surface than on the (111) surface.     

Adsorption and Decarbonylation Reaction of Furfural on the Pd(111) and M/Pd(111)(M=Ni,Cu and Ru) Surfaces

By performing with density functional theory(DFT) method, the detailed adsorption process and the catalytic decarbonylation mechanisms of furfural over Pd(111) and M/Pd(111)(M = Ni, Cu, Ru) surfaces toward furan were clarified. The results of atomic size factor, formation energy and d-band center showed that Ru/Pd(111) surface was the most stable and active. The adsorption energies of furfural on the different surfaces followed the order Ru/Pd(111) Cu/Pd(111) Pd(111) Ni/Pd(111). After analyzing Mulliken atomic charge population and the deformation density, we can find that on Ru/Pd(111) surface, the number of charge transfer was the most and the interaction was the strongest. Therefore, its adsorption energy was the highest. Furthermore, the furfural decarbonylation pathway is more kinetically feasible on bimetallic surface, and the reaction is the most likely to occur on Ru/Pd(111).