Static and dynamic sorption study of heavy metal ions on amino-functionalized SBA-15

Amino-functionalized SBA-15 mesoporous silica (SBA-15-NN) was synthesized using the normal grafting procedure of SBA-15 with [3-(2-Aminoethyl) aminopropyl] trimethoxysilane. Under optimal conditions, SBA-15-NN exhibited a higher adsorption capacity toward metal ions than SBA-15 in static adsorption. The results showed that the flow rate of 2?mL?min^?1 might be the optimum flow rate in dynamic adsorption, and the higher initial metal ion concentration is favorable for the adsorption of Zn(II), Co(II), and Ni(II) onto SBA-15-NN. The results indicated that SBA-15-NN could effectively remove multiple metal ions from aqueous solution as a good adsorption material.     

Correlation between pore-expanding and dye adsorption of platelet C/SBA-15 prepared by carbonization and oxidation of P123-TMB/SBA-15 composites

Platelet SBA-15 with significantly shortened and larger mesopores were prepared with different dosage of trimethylbenzene (TMB) in the assembly process, and then functionalized with acidic oxygen groups by oxidation of carbon layer that obtained by carbonization of P123-TMB organic species occluded in the silica pores. The preparation procedure involved three steps, namely, (a) synthesis platelet SBA-15 with larger mesopores, (b) carbonization, using P123 in the pore directly as the carbon source, and (c) oxidation with K₂S₂O₈. The resulting oxidation and carbonization of platelet SBA-15 (CST-ox, where C = carbon, S = SBA-15, T = trimethylbenzene, and ox refers to oxidation) composites contained of carbonaceous matter with acid oxygen groups (e.g. –COOH, –C=O and –OH) attached onto the deposited carbon layer. The structural characteristics of the parent silica were retained in the oxidized composite materials, which exhibit high surface area, large pore volume and well-ordered porosity. The oxygen-functionalized CST-ox composites with larger mesopores were found to be excellent adsorbents towards methylene blue. Especially, the adsorption equilibrium time was significantly reduced from 60 to 20 min, and the maximum adsorption capacity was increased from 379 to 420 mg/L, for which may be closely associated with the larger pore size, highly shortened meso-channels and the functionalized carbon layers. The adsorption kinetic data were analysed using pseudo-first-order, pseudo-second-order and Weber’s intraparticle diffusion models. Also equilibrium data were fitted to the Langmuir, Freundlich isotherm models and isotherm constants were determined. Thermodynamic parameters such as changes in the free energy of adsorption (ΔG ⁰), enthalpy (ΔH ⁰) and entropy (ΔS ⁰) were calculated.     

Functionalized SBA-15 materials as carriers for controlled drug delivery: influence of surface properties on matrix-drug interactions

Mesoporous SBA-15 materials were functionalized with amine groups through postsynthesis and one-pot synthesis, and the resulting functionalized materials were investigated as matrixes for controlled drug delivery. The materials were characterized by FTIR, N(2) adsorption/desorption analysis, zeta potential measurement, XRD, XPS, and TEM. Ibuprofen (IBU) and bovine serum albumin (BSA) were selected as model drugs and loaded onto the unmodified and functionalized SBA-15. It was revealed that the adsorption capacities and release behaviors of these model drugs were highly dependent on the different surface properties of SBA-15 materials. The release rate of IBU from SBA-15 functionalized by postsynthesis is found to be effectively controlled as compared to that from pure SBA-15 and SBA-15 functionalized by one-pot synthesis due to the ionic interaction between carboxyl groups in IBU and amine groups on the surface of SBA-15. However, SBA-15 functionalized by one-pot synthesis is found to be more favorable for the adsorption and release of BSA due to the balance of electrostatic interaction and hydrophilic interaction between BSA and the functionalized SBA-15 matrix.     

Mesoporous SBA-15 materials modified with PW or W active species as catalysts for the epoxidation of olefins with H<Subscript>2</Subscript>O<Subscript>2</Subscript>

Five catalysts containing PW or W active species that anchored onto aminosilylated mesoporous silica SBA-15 by a post-grafting route were prepared and the resulting PW or W/APTES/SBA-15 hybrid materials were characterized by XRD, N₂ adsorption/desorption, surface area analysis, TEM, FT-IR, and ICP (inductively coupled plasma atomic emission spectroscopy). The names of these catalysts have been abbreviated as SBA-15m-a, SBA-15m-b, SBA-15m-c, SBA-15m-d, and SBA-15m-e according to the different active species. The PW or W active species were highly dispersed in the channels of the modified mesoporous materials. The interaction between PW or W species and amino groups grafted on the channel surface of SBA-15 led to the immobilization of PW or W species. Their catalytic activity in the epoxidation of cyclooctene with H₂O₂ as oxidant was investigated. Among them, SBA-15m-a showed the best performance, with 98.9% conversion and 98.4% selectivity. The catalyst could be reused for six times with a little decrease in activity.     

Guest-host encapsulation of microporous zeolites in ordered mesoporous materials by molecular simulations

The present work provides the first study of ordered mesoporous materials SBA-15 coated with microporous zeolites ZSM-5 using molecular simulations. Several model structures with characteristics such as periodic arrangement of mesopores, randomly arranged micropores, surface hydroxyls and bulk deformations of SBA-15 were used. Cartesian coordinates of ZSM-5 unit lattice were obtained from the literature and the 100 face of H-ZSM-5 unit cell was then placed on the surface of SBA-15 and the entire structure was equilibrated to obtain final configuration. The resulting structure was characterized using simulated small angle and wide angle X-ray diffraction, Connolly surface area (to compare BET area), accessible pore volume for nitrogen molecules (to compare with t-plot volume of micro and mesopores) and methane adsorption at 303 K. The orientation of ZSM-5 on the SBA-15 had no effect on the surface area, pore volume or adsorption capacity. In order to find out if the addition of microporous ZSM-5 should increase the total methane adsorption capacity due to addition of micropores, we studied adsorption on bare and coated SBA-15. However, total adsorption capacity was found to decrease, while the number of methane molecules adsorbed per unit cell of the SBA-15 structure increased. An existing experimental method (J. Am. Chem. Soc., 2004, 126, 14324) of the synthesizing hybrid ZSM-5/SBA-15 structure was studied using accessible micropore volume (by t-plot). It was found that the procedure made all the micropores inaccessible. A modification of the method or use of other host materials is suggested to use the benefits of narrow micropore distribution in ZSM-5.     

Adsorption and structural properties of channel-like and cage-like organosilicas

Channel-like and cage-like mesoporous silicas, SBA-15 (P6mm symmetry group) and SBA-16 (Im3m symmetry group), were modified by introducing single ureidopropyl surface groups, mixed ureidopropyl and mercaptopropyl surface groups, and single bis(propyl)disulfide bridging groups. These hexagonal and cubic organosilicas were prepared under acidic conditions via co-condensation of tetraethyl orthosilicate (TEOS) and proper organosilanes using poly(ethylene oxide)-block-poly(propylene oxide)-block-poly(ethylene oxide) amphiphilic block copolymer templates, P123 (EO₂₀PO₇₀EO₂₀) and F127 (EO₁₀₆PO₇₀EO₁₀₆). The modified SBA-15 and SBA-16 materials were synthesized by varying the molar ratio of organosilane to TEOS in the initial synthesis gel. The removal of polymeric templates, P123 and F127, was performed with ethanol/hydrochloric acid solution. In the case of SBA-15 the P123 template was fully extracted, whereas this extraction process was less efficient for the removal of F127 template from the SBA-16-type organosilicas; in the latter case a small residue of F127 was retained. The adsorption and structural properties of the resulting materials were studied by nitrogen adsorption-desorption isotherms at −196^∘C (surface area, pore size distribution, pore volumes), powder X-Ray diffraction, CHNS elemental analysis and high-resolution thermogravimetry. The structural ordering, the BET specific surface area, pore volume and pore size decreased for both channel-like and cage-like mesoporous organosilicas with increasing concentration of incorporated organic groups.     

Immobilization of hemoglobin on SBA-15 applied to the electrocatalytic reduction of H<Subscript>2</Subscript>O<Subscript>2</Subscript>

The direct electron transfer between hemoglobin (Hb) and an electrode was realized by first immobilizing the protein onto SBA-15.The results of the immobilization showed that the adsorption was pH-dependent with a maximum adsorption near the isoelectric point of the protein, and SBA-15 with a larger pore diameter showed greater adsorption capacity for Hb. UV–vis spectroscopy and nitrogen adsorption analysis indicated that Hb was adsorbed within the channel of SBA-15 and no significant denaturation occurred to the protein. The Hb/SBA-15 composite obtained was used for the fabrication of a Hb biosensor to detect hydrogen peroxide. A pair of well-defined redox peaks at −0.337 and −0.370 V on the Hb/SBA-15 composite modified glassy carbon electrode was observed, and the electrode reactions showed a surface-controlled process with a single proton transfer at a scan rate range from 20 to 1,000 mV/s. The sensor showed a fast amperometric response, a low detection limit (2.3 × 10⁻⁹ M) and good stability for the detection of H₂O₂. The electrochemical results indicated that the immobilized Hb still retained its biological activity.     

有序介孔二氧化硅对正丁醛的吸附性能

合成了一系列具有不同孔结构与性质的有序介孔二氧化硅材料SBA-15、MCM-41、SBA-16、KIT-6, 同时通过改变水热温度制备了不同孔径大小的SBA-15, 并利用小角X射线散射、透射电镜、扫描电镜和氮气吸附-脱附等手段, 对其介孔结构进行了表征. 以正丁醛为探针分子, 考察了其对有机醛的吸附, 并与Y-沸石的吸附性能做了对比. 结果表明, 材料的介孔比表面积与其对正丁醛的吸附量成正比, 吸附等温线符合Langmuir 模型, 属于单层吸附, 具有最大介孔比表面积的MCM-41对正丁醛的吸附量最大(484 mg·g^-1). 最后将SBA-15添加到卷烟滤嘴中, 实验结果表明, SBA-15能显著降低卷烟烟气中巴豆醛的释放量.     

Piroxicam Loading onto Mesoporous Silicas by Supercritical CO2 Impregnation

Piroxicam (PRX) is a commonly prescribed nonsteroidal anti-inflammatory drug. Its efficacy, however, is partially limited by its low water solubility. In recent years, different studies have tackled this problem and have suggested delivering PRX through solid dispersions. All these strategies, however, involve the use of potentially harmful solvents for the loading procedure. Since piroxicam is soluble in supercritical CO₂ (scCO₂), the present study aims, for the first time, to adsorb PRX onto mesoporous silica using scCO₂, which is known to be a safer and greener technique compared to the organic solvent-based ones. For comparison, PRX is also loaded by adsorption from solution and incipient wetness impregnation using ethanol as solvent. Two different commercial mesoporous silicas are used (SBA-15 and Grace Syloid^® XDP), which differ in porosity order and surface silanol population. Physico-chemical analyses show that the most promising results are obtained through scCO₂, which yields the amorphization of PRX, whereas some crystallization occurs in the case of adsorption from solution and IWI. The highest loading of PRX by scCO₂ is obtained in SBA-15 (15 wt.%), where molecule distribution appears homogeneous, with very limited pore blocking.     

Characterization and acidic properties of Al-SBA-15 materials prepared by post-synthesis alumination of a low-cost ordered mesoporous silica

A series of Al-containing SBA-15 type materials with different Si/Al ratio, were prepared by post-synthesis modification of a pure highly ordered mesoporous silica SBA-15 obtained by using sodium silicate as silica source, and amphiphilic block copolymer as structure-directing agent. A high level of aluminum incorporation was achieved, reaching an Si/Al ratio of up to 5.5, without any significant loss in the textural properties of SBA-15. These materials were fully characterized by powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), ²⁷Al NMR spectroscopy, and N₂ adsorption at 77 K. The acid properties of these materials have been evaluated by NH₃-TPD, adsorption of pyridine and deuterated acetonitrile coupled to FTIR spectroscopy. The effective acidity of these materials was evaluated using two catalytic reactions: 2-propanol dehydrogenation and 1-butene isomerization. The adsorption of basic probe molecules and the catalytic behavior revealed an evolution of the acid properties with the Al content. These studies have shown that the Al-SBA-15 materials contain Brønsted and Lewis acid sites with medium acidity which makes them appropriate to be used as acid catalysts in heterogeneous catalysis, catalytic supports, and adsorbents.     

Highly ordered Ti-SBA-15: Efficient H2 adsorbent and photocatalyst for eco-toxic dye degradation

Highly ordered 2D-hexagonal mesoporous titanium silicate Ti-SBA-15 materials (space group p6mm) have been synthesized hydrothermally in acidic medium employing amphiphilic tri-block copolymer, Pluronic F127 as structure directing agent. Samples are characterized by powder X-ray diffraction, transmission electron microscopy, scanning electron microscopy, FT IR spectroscopy, UV-visible diffuse reflectance measurements, N₂ adsorption/desorption and TG-DTA analysis. XRD and TEM results suggested the presence of highly ordered mesophase with hexagonal pore arrangements. BET surface area for Ti-SBA-15 (924 m² g⁻¹) is considerably higher than the pure silica SBA-15 (611 m² g⁻¹) prepared following the same synthetic route. UV-visible and FT-IR studies suggested the incorporation of mostly tetrahedral titanium (IV) species, along with some six-coordinated sites in the silicate network. This material shows very good H₂ adsorption capacity at higher pressure and excellent catalytic activity in the photocatalytic degradation of ecologically abundant dye methylene blue.     

Amino-functionalized pore-expanded SBA-15 for CO2 adsorption

The adsorption of CO₂ on pore-expanded SBA-15 mesostructured silica functionalized with amino groups was studied. The synthesis of conventional SBA-15 was modified to obtain pore-expanded materials, with pore diameters from 11 to 15 nm. Post-synthesis functionalization treatments were carried out by grafting with diethylenetriamine (DT) and by impregnation with tetraethylenepentamine (TEPA) and polyethyleneimine (PEI). The adsorbents were characterized by X-ray diffraction, N₂ adsorption–desorption at 77 K, elemental analysis and Transmission Electron Microscopy. CO₂ capture was studied by using a volumetric adsorption technique at 45 °C. Consecutive adsorption–desorption experiments were also conducted to check the cyclic behaviour of adsorbents in CO₂ capture. An improvement in CO₂ adsorption capacity and efficiency of amino groups was found for pore-expanded SBA-15 impregnated materials in comparison with their counterparts prepared from conventional SBA-15 with smaller pore size. PEI and TEPA-based adsorbents reached significant CO₂ uptakes at 45 °C and 1 bar (138 and 164 mg CO₂/g, respectively), with high amine efficiencies (0.33 and 0.37 mol CO₂/mol N), due to the positive effect of the larger pore diameter in the diffusion and accessibility of organic groups. Pore-expanded SBA-15 samples grafted with DT and impregnated with PEI showed a good stability after several adsorption–desorption cycles of pure CO₂. PEI-impregnated adsorbent was tested in a fixed bed reactor with a diluted gas mixture containing 15 % CO₂, 5 % O₂, 80 % Ar and water (45 °C, 1 bar). A noteworthy adsorption capacity of 171 mg CO₂/g was obtained in these conditions, which simulate flue gas after the desulphurization step in a thermal power plant.     

Modulation of the Activity of Gold Clusters Immobilized on Functionalized Mesoporous Materials in the Oxidation of Cyclohexene via the Functional Group. The Case of Aminopropyl Moiety

Gold nanoclusters and isolated gold atoms have been produced in a two-liquid phase procedure that involves a solution of gold in aqua regia and rosemary essential oil as organic layer. These gold entities have been immobilized on the ordered mesoporous silica material SBA-15 functionalized with different amounts of aminopropyl groups. The resulting materials have been characterized by XRD, N₂ adsorption, chemical analysis, TGA, ²⁹Si MAS NMR, ¹³C CP/MAS NMR, UV-vis spectroscopy, XPS, and STEM. The Au-containing materials retain the ordering and porosity of the pristine support. Gold content varies in the range of 0.07–0.7 wt% as a function of the specific immobilization conditions, while STEM evidences the presence of isolated gold atoms. XPS shows a shift of the Au 4f BE toward values lower than those of metallic gold. The catalytic activity in the oxidation of cyclohexene with molecular oxygen at atmospheric pressure parallels the Au content of the aminopropyl-SBA-15 supports. This activity is higher than that of analogous Au entities immobilized on SBA-15 functionalized with thiol or sulfonate groups, the activity decreasing in the order Au-NH₂ > Au-SO₃⁻ > Au-SH. This behavior has been attributed to differences in the interaction strength between the functional group and the Au entities, which is optimum for the aminopropyl groups.     

以廉价国产化试剂合成大孔径高度有序介孔氧化硅分子筛

新一代大孔径（１～３０nm）介孔分子筛在大分子转化、吸附、生物大分子分离以及电磁、传感器、光电子等领域均具有广泛的应用前景犤１～４犦。由昂贵的长链有机季铵盐阳离子表面活性剂为模板合成的MCM－４１介孔分子筛，由于其孔径小，水热稳定性差，受到了较大的限制。与其相比，以嵌段高分子共聚物为模板剂合成的介孔分子筛SBA－１５具有孔径均一，有序度高，并且其孔径大以及水热性能良好等优点，近年来得到了广泛的研究犤５～９犦。其骨架上修饰有机硅烷，可用于重金属的分离、回收，以及蛋白质的控释与分离。利用主－客体方法在SB…     

MOR/SBA-15复合分子筛的合成、表征及其催化性能评价

采用MOR纳米晶和正硅酸四乙酯为硅源,P123三嵌段共聚物为模板剂水热合成MOR/SBA-15复合分子筛催化剂。采用XRD、SEM、TEM和EDX等手段对催化剂进行了表征,在固定床反应器中评价二甲醚制乙醇催化性能。结果表明,通过控制合适的MOR纳米晶种及MOR纳米晶种在SBA-15水热合成体系中的添加量,可以成功地将MOR纳米晶作为SBA-15的结构单元嫁接到SBA-15的介孔骨架中,水热合成的MOR/SBA-15复合分子筛催化剂同时具有MOR和SBA-15的XRD特征衍射峰,相比于SBA-15,其比表面积和总孔体积由756 m2·g~(-1),1.07 cm3·g~(-1)降低至628 m2·g~(-1),0.85 cm3·g~(-1),平均孔径由8.1 nm提高到9.3nm,Cu修饰的MOR/SBA-15复合分子筛催化剂同时具有Cu MOR羰基化和Cu SBA-15加氢的双功能催化性能,其催化剂评价结果显示二甲醚转化率为43.6%左右,乙醇选择性为95.3%,Cu MOR/SBA-15复合分子筛催化剂实现了二甲醚到乙醇的一步转化。     

Thermal stability of high surface area silicon carbide materials

The synthesis of mesoporous silicon carbide by chemical vapor infiltration of dimethyl dichlorosilane into mesoporous silica SBA-15 and subsequent dissolution of the silica matrix with HF was investigated. The influence of the synthesis parameters of the composite material (SiC/SBA-15) on the final product (mesoporous SiC) was determined. Depending on the preparation conditions, materials with specific surface areas from 410 to 830 m² g⁻¹ and pore sizes between 2 and 10 nm with high mesopore volume (0.31-0.96 cm³ g⁻¹) were prepared. Additionally, the thermal stability of mesoporous silicon carbide at 1573 K in an inert atmosphere (argon) was investigated, and compared to that of SBA-15 and ordered mesoporous carbon (CMK-1). Mesoporous SiC has a much higher thermal textural stability as compared to SBA-15, but a lower stability than ordered mesoporous carbon CMK-1.     

Adsorption-assistant detection of trace uranyl ion with high sensitivity and selectivity in the presence of SBA-15

A new strategy adsorption-assistant detection of trace uranyl ion is developed in this work employing fluorescence techniqe. Specifically, mesoporous molecular sieve SBA-15 is introduced in the process of determination of uranyl by esculin to enhance the sensitivity and selectivity. A linear detecting range of 0.001–0.05 μM and a limit of detection of 6 nM are achieved, which is probably due to the adsorption of both esculin and uranyl ion onto SBA-15. The K_SV value is 8.69?×?10⁶ mol^?1 L, which was ca. 40 times of that without SBA-15.     

Study on the controllable synthesis of SH-MCM-41 mesoporous materials and their adsorption properties of the La3+, Gd3+ and Yb3+

Sulfhydryl MCM-41 (SH-MCM-41) mesoporous materials were prepared via a hydrothermal method, and -SH was successfully imported by a post-grafting method. The structure and surface properties of the materials were characterized using Fourier Transform infrared spectroscopy, X-ray diffraction and Transmission Electron Microscopy analysis. The low concentrations of La³⁺, Gd³⁺ and Yb³⁺ adsorption on the material were investigated. This paper discusses the effects of system factors, such as pH and the solid-liquid ratio, on the performance of the adsorption process. The adsorption thermodynamics and kinetics were also explored. Experimental results indicated that the materials were in good order and had high specific surface area (956 m²/g) with an average pore diameter of 2.1 nm; the mercapto groups were successfully grafted onto a molecular sieve, and the best grafted amount was 1.46 × 10^?3 mol/g. The materials showed preferable adsorption of La³⁺, Gd³⁺ and Yb³⁺ with maximum adsorption capacities of 560.56 mg/g, 467.60 mg/g and 540.68 mg/g, respectively. The adsorption process can be described by the Freundlich isotherm model, and the adsorption data fits pseudo-second-order kinetics. After repeating the elution-regeneration cycle four times, the adsorption capacity of rare earth ions was mostly maintained, indicating that the adsorbent can be regenerated well and recycled to save costs. It has potential in practical application.     

One-step direct synthesis of mesoporous aluminosilicates Al-SBA-15 with cage-like macropores by using micrometer-sized aluminum balls

Ordered mesoporous aluminosilicate Al-SBA-15 materials with cage-like macropores have been synthesized by using micrometer-sized aluminum balls as an Al source, tetraethyl orthosilicate (TEOS) as a silica source, and triblock copolymer Pluronic P123 as a template. The resulting materials were fully characterized by XRD, N₂ adsorption, SEM, TEM, ICP-AES, and ²⁷Al MAS-NMR. The products (Al-SBA-15) have ordered two-dimensional (2-D) hexagonal mesostructures (space group p6mm). The calcined Al-SBA-15 materials exhibit disordered macropores with diameters of about 70–80 nm and ordered mesopores with a diameter of ∼5 nm, a BET surface area of about 500 m²/g, Si/Al ratio of 40–80, and a ratio of tetrahedral Al to octahedral Al sites of about 2:1. This combination of properties gives these materials potential applications in areas such as adsorption, catalysis and separation. Supported by the National Natural Science Foundation of China (Grant Nos. 20890123 & 20721063), Shanghai Science & Technology Committee (08DZ2270500), and Shanghai Leading Academic Discipline Project (No.B108)     

Organo-modified mesoporous silica for sorption of carbon dioxide

Abstract  

Organo-modified mesoporous silica SBA-15 has been studied for sorption of carbon dioxide (CO₂). The SBA-15 sample was functionalized with a branched chain polymer, polyethylenimine (PEI), of different molecular weights (1,300 and 2,000 g mol⁻¹). Surface modification was carried out by impregnation of silica by PEI or by grafting with (3-chloropropyl)triethoxysilane, followed by substitution of chlorine atoms by PEI ligands. The prepared modified mesoporous materials were characterized by nitrogen adsorption/desorption at 77 K, high-resolution transmission electron microscopy, small-angle X-ray scattering, and thermal methods. Sorption of CO₂ was studied by gravimetric method at 303 K. The total amount of sorbed CO₂ varied between 0.19–0.67 mmol/g for respective samples. Regeneration of the materials after adsorption was achieved by thermal treatment at 343 K.