Pre‐irradiation grafting of styrene/divinylbenzene (DVB) onto poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP) films from isopropanol (iPrOH) solution was investigated with respect to the effect of irradiation dose, film thickness, cross‐linker concentration, and reaction temperature. A mathematical model was applied to the kinetic curves to extract information on the polymerization rate, the radical‐recombination rate, and the grafting through time. It turned out that the two closely correlated reaction rates for polymerization and radical recombination can be varied over a wide range by changing the irradiation dose, the cross‐linker concentration, and the reaction temperature. On the other hand, the time until the grafting front has progressed to the center of the film is mainly affected by the film thickness and the reaction temperature. The formation of homopolymer in the grafting solution increases steeply with temperature and cross‐linker concentration. 相似文献
Summary: The reaction of triphosgene with poly(ethylene glycol) yielded poly(ethylene glycol) dichloroformate. This difunctional cross‐linker was allowed to react with poly(ε‐caprolactone) bearing carbanionic sites obtained by activation with lithium diisopropylamide. The reaction resulted in the cross‐linking of poly(ε‐caprolactone) chains by poly(ethylene glycol) segments, giving copolymer networks that gel in both organic and aqueous media.
Schematic of the PCL‐g‐PEG copolymers synthesized here. 相似文献
A supramolecular cross‐linked cross‐linker, capable of introducing rotaxane cross‐links to vinyl polymers, has been developed for the rational synthesis of polyrotaxane networks. The experimental results reveal that the combination of an oligocyclodextrin (OCD) and a terminal bulky group‐tethering macromonomer (TBM) forms a polymer‐network structure having polymerizable moieties through supramolecular cross‐linking. Radical polymerization of a variety of typical vinyl monomers in the presence of the vinylic supramolecular cross‐linker (VSC) afforded the corresponding vinyl polymers cross‐linked through the rotaxane cross‐links (RCP) as transparent stable films in high yields under both photoinitiated and thermal polymerization conditions. A poly(N,N‐dimethylacrylamide)‐based hydrogel synthesized by using VSC, RCPDMAAm, displayed a unique mechanical property. The small‐angle X‐ray scattering (SAXS) results, indicating patterns characteristic of a polyrotaxane network, clearly suggested the presence and role of the rotaxane cross‐links. The confirmation of the introduction of rotaxane‐cross‐links into vinyl polymers strongly reveals the significant usefulness of VSC. 相似文献
A polystyrene‐cross‐linking tricyclohexylphosphine (PS‐TCP) was synthesized through radical emulsion polymerization of 4‐tert‐butylstyrene as a monomer and tris(trans‐4‐styrylcyclohexyl)phosphine as a threefold cross‐linker. The PS‐TCP showed enhanced ligand performance compared to the corresponding polystyrene‐triphenylphosphine hybrid PS‐TPP and tricyclohexylphosphine in Pd‐catalyzed Suzuki–Miyaura and Buchwald–Hartwig reactions of aryl chlorides. 相似文献
Carboxymethyl cellulose (CMC) is functionalized with norbornene groups to undergo thiol‐norbornene cross‐linking reactions. Hydrogels synthesized from a single norbornene‐modified carboxymethyl cellulose (NorCMC) via a light‐initiated thiol‐ene cross‐linking reaction with a variety of dithiol cross‐linkers yield hydrogels with a tunable compression modulus ranging from 1.7 to 103 kPa. Additionally, thermoresponsiveness is spatiotemporally imparted to NorCMC hydrogels by photopatterning a dithiol‐terminated poly(N‐isopropyl acrylamide) cross‐linker, enabling swelling and topological control of the hydrogels as a function of incubation temperature. NorCMC hydrogels are cytocompatible as the viability of encapsulated human mesenchymal stem cells (hMSCs) is greater than 85% after 21 d while using a variety of cross‐linkers. Moreover, hMSCs can remodel, adhere, and spread in the NorCMC matrix cross‐linked with a matrix metalloproteinase‐degradable peptide, further demonstrating the utility of these materials as a tunable biomaterial. 相似文献
(Acetoxymethyl)silanes 2 , 7 a – c , and 10 a – c with at least one alkoxy group, of the general formula (AcOCH2)Si(OR)3?n(CH3)n (R: Me, Et, iPr; n=0, 1, 2), were synthesized from the corresponding (chloromethyl)silanes 1 , 6 a – c , and 9 a – c by treatment with potassium acetate under phase‐transfer‐catalysis conditions. These compounds were found to provide 2,2,5,5‐organo‐substituted 1,4‐dioxa‐2,5‐disilacyclohexanes 3 , 8 a – c , and 11 a – c if treated with organotin(IV) catalysts such as dioctyltin oxide. The reaction proceeds through transesterification of the acetoxy and alkoxy units followed by ring‐closure to form a dimeric six‐membered ring. The corresponding alkyl acetates are formed as the reaction by‐products. With these mild conditions, the method overcomes the drawbacks of previously reported synthetic routes to furnish 2,2,5,5‐tetramethyl‐1,4‐dioxa‐2,5‐disilacyclohexane ( 3 ) and even allows the synthesis of 1,4‐dioxa‐2,5‐disilacyclohexanes bearing hydrolytically labile alkoxy substituents at the silicon atom in good yields and high purity. These new materials were fully characterized by NMR spectroscopy, elemental analysis, mass spectrometry, and X‐ray analysis (trans‐ 8 a ). 相似文献
A novel neutral polymer, {[Co2(C7H3NO4)2(H2O)4]·2H2O}n, was hydrothermally synthesized using pyridine‐2,5‐dicarboxylate (2,5‐PDC2−) as the organic linker. It features a two‐dimensional layer structure constructed from one‐dimensional {[Co(2,5‐PDC)2]2−}n chains interlinked by [Co(H2O)4]+ units. The two CoII cations occupy special positions, sitting on inversion centres. Each 2,5‐PDC2− anion chelates to one CoII cation via the pyridine N atom and an O atom of the adjacent carboxylate group, and links to two other CoII cations in a bridging mode via the O atoms of the other carboxylate group. In this way, the 2,5‐PDC2− ligand connects three neighbouring CoII centres to form a two‐dimensional network. The two‐dimensional undulating layers are linked by extensive hydrogen bonds to form a three‐dimensional supramolecular structure, with the uncoordinated solvent molecules occupying the interlamellar region. 相似文献
In this paper, a novel highly cross‐linked porous monolithic stationary phase having a long alkyl chain ligand (C16) was introduced and evaluated in CEC. The monolithic stationary phase was prepared by in situ copolymerization of 1‐hexadecene, trimethylolpropane trimethacrylate, and 2‐acrylamido‐2‐methyl‐1‐propanesulfonic acid (AMPS) in the presence of ternary porogenic solvent (cyclohexanol/1,4‐butanediol/water). In preparing monoliths, the ternary cross‐linker trimethylolpropane trimethacrylate was usually applied to preparing molecularly imprinted polymers or molecularly imprinted solid‐phase extraction, instead of binary cross‐linker ethylene dimethacrylate. 1‐Hexadecene was introduced to provide the non‐polar sites (C16) for chromatographic retention, while AMPS was used to generate the EOF for transporting the mobile phase through the monolithic capillary. Monolithic columns were prepared by optimizing proportion of porogenic solvent and AMPS content in the polymerization solution as well as the cross‐linkers. The monolithic stationary phases could generate a strong and stable EOF in various pH values and exhibit an RP‐chromatographic behavior for neutral compounds. For charged compounds, the separation was mainly based on the association of hydrophobic, electrostatic and electrophoretic interaction. 相似文献
A bottom‐up strategy was used for the synthesis of cross‐linked copolymers containing the organocatalyst N‐{(1R)‐2′‐{[(4‐ethylphenyl)sulfonyl]amino}[1,1′‐binaphthalen]‐2‐yl}‐D ‐prolinamide derived from 2 (Scheme 1). The polymer‐bound catalyst 5b containing 1% of divinylbenzene as cross‐linker showed higher catalyst activity in the aldol reaction between cyclohexanone and 4‐nitrobenzaldehyde than 5a and 5c . Remarkably, the reaction in the presence of 5b was carried out under solvent‐free, mild conditions, achieving up to 93% ee (Table 1). The polymer‐bound catalyst 5b was recovered by filtration and re‐used up to seven times without detrimental effects on the achieved diastereo‐ and enantioselectivities (Table 2). The catalytic procedure with polymer 5b was extended to the aldol reaction under solvent‐free conditions of other ketones, including functionalized ones, and different aromatic aldehydes (Table 3). In some cases, the addition of a small amount of H2O was required to give the best results (up to 95% ee). Under these reaction conditions, the cross‐aldol reaction between aldehydes proceeded in moderate yield and diastereo‐ and enantioselectivity (Scheme 2). 相似文献