Crystallization and melting of isotactic polypropylene crystallized from quiescent melt and stress‐induced localized melt

Temperature dependency of crystalline lamellar thickness during crystallization and subsequent melting in isotactic polypropylene crystallized from both quiescent molten state and stress‐induced localized melt was investigated using small angle X‐ray scattering technique. Both cases yield well‐defined crystallization lines where inverse lamellar thickness is linearly dependent on crystallization temperature with the stretching‐induced crystallization line shifted slightly to smaller thickness direction than the isothermal crystallization one indicating both crystallization processes being mediated a mesomorphic phase. However, crystallites obtained via different routes (quiescent melt or stress‐induced localized melt) show different melting behaviors. The one from isothermal crystallization melted directly without significant changing in lamellar thickness yielding well‐defined melting line whereas stress‐induced crystallites followed a recrystallization line. Such results can be associated with the different extent of stabilization of crystallites obtained through different crystallization routes. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 957–963     

Two‐dimensional Fourier transform infrared spectroscopy study of biosynthesized poly(hydroxybutyrate‐co‐hydroxyhexanoate) and poly(hydroxybutyrate‐ co‐hydroxyvalerate)

Generalized two‐dimensional (2D) Fourier transform infrared correlation spectroscopy was used to investigate the effect of the comonomer compositions on the crystallization behavior of two types of biosynthesized random copolymers, poly(hydroxybutyrate‐co‐hydroxyhexanoate) and poly(hydroxybutyrate‐co‐hydroxyvalerate). The carbonyl absorption band around 1730 cm^?1 was sensitive to the degree of crystallinity. 2D correlation analysis demonstrated that the 3‐hydroxyhexanoate units preferred to remain in the amorphous phase of the semicrystalline poly(hydroxybutyrate‐co‐hydroxyhexanoate) copolymer, resulting in decreases in the degree of crystallinity and the rate of the crystallization process. The poly(hydroxybutyrate‐co‐hydroxyvalerate) copolymer maintained a high degree of crystallinity when the 3‐hydroxyvalerate fraction was increased from 0 to 25 mol % because of isodimorphism. The crystalline and amorphous absorption bands for the carbonyl bond for this copolymer, therefore, changed simultaneously. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 649–656, 2002; DOI 10.1002/polb.10126     

Crystallization and morphology of poly(vinylidene fluoride)/poly(3‐hydroxybutyrate) blends. II. Morphology and crystallization kinetics by time resolved X‐ray scattering

The development of the morphology in poly(vinylidene fluoride)/poly(3‐hydroxybutyrate) (PVDF/PHB) blends upon isothermal and anisothermal crystallization is investigated by time‐resolved small‐ and wide‐angle X‐ray scattering. The components are completely miscible in the melt but crystallize separately; they crystallize stepwise at different temperatures or sequentially with isothermal or anisothermal conditions, respectively. The PVDF crystallizes undisturbed whereas PHB crystallizes in a confined space that is determined by the existing supermolecular structure of the PVDF. The investigations reveal that composition inhomogeneities may initially develop in the remaining melt or in the amorphous phases of the PVDF upon crystallization of that component. The subsequent crystallization of the PHB depends on these heterogeneities and the supermolecular structure of PVDF (dendritically or globularly spherulitic). PHB may form separate spherulites that start to grow from the melt, or it may develop “interlocking spherulites” that start to grow from inside a PVDF spherulite. Occasionally, a large number of PVDF spherulites may be incorporated into PHB interlocking spherulites. The separate PHB spherulites may intrude into the PVDF spherulites upon further growth, which results in “interpenetrating spherulites.” Interlocking and interpenetrating are realized by the growth of separate lamellar stacks (“fibrils”) of the blend components. There is no interlamellar growth. The growth direction of the PHB fibrils follows that of the existing PVDF fibrils. Depending on the distribution of the PHB molecules on the interlamellar and interfibrillar PVDF regions, the lamellar arrangement of the PVDF may contract or expand upon PHB crystallization and the adjacent fibrils of the two components are linked or clearly separated. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 974–985, 2004     

Crystallization and morphology of poly(vinylidene fluoride)/poly(3‐hydroxybutyrate) blends. III. Crystallization and phase diagram by differential scanning calorimetry

The crystallization of poly(vinylidene fluoride) (PVDF)/poly(3‐hydroxybutyrate) (PHB) blends was studied with differential scanning calorimetry, from which the phase diagram was derived. Strong miscibility was underlined by the large negative Flory–Huggins interaction parameter (?0.25). The crystallization of the blend components differed remarkably. Whereas PVDF always crystallized in the surroundings of a homogeneous melt, PHB crystallized in a volume that was confined by the already existing PVDF spherulites, partly in their surroundings and partly inside. Under isothermal conditions, PVDF usually crystallized regularly in three dimensions with predominant quench‐induced athermal nucleation. The Avrami exponent for PVDF dendritic spherulitic growth was, however, distinctly smaller than that for compact growth, and this revealed the two‐dimensional lamellar growth inside. This deviation from ideal Avrami behavior was caused by the development of compositional inhomogeneities as PVDF crystallization proceeded, and this decelerated the kinetics. PHB crystallized three‐dimensionally with mixed thermal and athermal nucleation outside the PVDF spherulites. Inside the PVDF spherulites, PHB crystallization proceeded in a fibrillar fashion with thermal nucleation; the growth front followed the amorphous paths inside the dendritic PVDF spherulites. The crystallization was faster than that in the melt of uncrystallized PVDF. Solid PVDF acts possibly heterogeneously nucleating, accelerating PHB crystallization. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 287–295, 2005     

Effects of carbon nanotubes on crystallization and melting behavior of poly(L‐lactide) via DSC and TMDSC studies

In this work, multiwalled carbon nanotubes (MWNTs) were surface‐modified and grafted with poly(L ‐lactide) to obtain poly(L ‐lactide)‐grafted MWNTs (i.e. MWNTs‐g‐PLLA). Films of the PLLA/MWNTs‐g‐PLLA nanocomposites were then prepared by a solution casting method to investigate the effects of the MWNTs‐g‐PLLA on nonisothermal and isothermal melt‐crystallizations of the PLLA matrix using DSC and TMDSC. DSC data found that MWNTs significantly enhanced the nonisothermal melt‐crystallization from the melt and the cold‐crystallization rates of PLLA on the subsequent heating. Temperature‐modulated differential scanning calorimetry (TMDSC) analysis on the quenched PLLA nanocomposites found that, in addition to an exothermic cold‐crystallization peak in the range of 80–120 °C, an exothermic peak in the range of 150–165 °C, attributed to recrystallization, appeared before the main melting peak in the total and nonreversing heat flow curves. The presence of the recrystallization peak signified the ongoing process of crystal perfection and, if any, the formation of secondary crystals during the heating scan. Double melting endotherms appeared for the isothermally melt‐crystallized PLLA samples at 110 °C. TMDSC analysis found that the double lamellar thickness model, other than the melting‐recrystallization model, was responsible for the double melting peaks in PLLA nanocomposites. Polarized optical microscopy images found that the nucleation rate of PLLA was enhanced by MWNTs. TMDSC analysis found that the incorporation of MWNTs caused PLLA to decrease the heat‐capacity increase (namely, ΔC_p) and the C_p at glass transition temperature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1870–1881, 2007     

Visualization of the Recrystallization of Solution‐Grown Poly[(R)‐3‐hydroxybutyrate] Lamellar Crystals

Morphological changes of solution‐grown poly[(R)‐3‐hydroxybutyrate] lamellar crystals during heating were directly investigated by atomic force microscopy. The thickening of lamellar crystals was further visualized by enzymatic degradation of less‐ordered crystal regions in thermally treated lamellar crystals. The morphological changes of lamellar crystals induced by thermal treatment are due to recrystallization.     

Effect of poly(butylene succinate) crystals on spherulitic growth of poly(ethylene oxide) in binary blends of the two substances

The effects of the lamellar growth direction, extinction rings, and spherulitic boundaries of poly(butylene succinate) (PBSU) on the spherulitic growth of poly(ethylene oxide) (PEO) were investigated in miscible blends of the two crystalline polymers. In the crystallization process from a homogeneous melt, PBSU first developed volume‐filling spherulites, and then PEO spherulites nucleated and grew inside the PBSU spherulites. The lamellar growth direction of PEO was identical with that of PBSU even when the PBSU content was about 5 wt %. PEO, which intrinsically does not exhibit banded spherulites, showed apparent extinction rings inside the banded spherulites of PBSU. The growth rate of a PEO spherulite, G_PEO, was influenced not only by the blend composition and the crystallization temperature of PEO, but also by the growth direction with respect to PBSU lamellae, the boundaries of PBSU spherulites, and the crystallization temperature of PBSU, T_PBSU. The value of G_PEO first increased with decreasing T_PBSU when a PEO spherulite grew inside a single PBSU spherulite. Then, G_PEO decreased when T_PBSU was further decreased and a PEO spherulite grew through many tiny PBSU spherulites. This behavior was discussed based on the aforementioned factors affecting G_PEO. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 539–547, 2009     

Comparison of different nucleating agents on crystallization of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerates)

In this study, thymine and melamine were introduced as nucleating agents for poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerates) (PHBVs) and poly(3‐hydroxybutyrate) (PHB), and their effects were compared with that of boron nitride (BN). Because the overall crystallization rate of PHBVs decreases significantly with the increase in the 3‐hydroxyvalerate comonomer content, the study focused on the crystallization of PHBVs. Isothermal crystallization kinetics of the neat PHBVs and the nucleated PHBVs were studied by differential scanning calorimetry (DSC). The Avrami equation was derived and the parameters were assessed for the nucleation and crystal growth mechanism. The nucleation and crystal growth were examined using polarized optical microscopy. All nucleating agents had similar particle sizes and showed good dispersion in the polymer matrix, as revealed by scanning electron microscopy. The results indicated that BN and thymine significantly increased the overall crystallization rate for all PHBVs studied and demonstrated very similar nucleating effects. Melamine reacted with PHBVs and accelerated the thermal degradation, and hence was less effective in nucleating PHBVs. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1564–1577, 2007     

Correlation between crystallization kinetics and microdomain morphology in block copolymer blends exhibiting confined crystallization

The crystallization kinetics of poly(ethylene oxide) (PEO) blocks in poly(ethylene oxide)‐block‐poly(1,4‐butadiene) (PEO‐b‐PB)/poly(1,4‐butadiene) (PB) blends were previously found to display a one‐to‐one correlation with the microdomain morphology. The distinct correlation was postulated to stem from the homogeneous nucleation‐controlled crystallization in the cylindrical and spherical PEO microdomains, where there existed a direct proportionality between the nucleation rate and the individual domain volume. This criterion was valid for confined crystallization in which the crystallization was spatially restricted within the individual domains. However, it was possibly not applicable to PEO‐b‐PB/PB, in that the melt mesophase was strongly perturbed upon crystallization. Therefore, it may be speculated that the crystal growth front developed in a given microdomain could intrude into the nearby noncrystalline domains, yielding the condition of cooperative crystallization. To establish an unambiguous model system for verifying the existence of microdomain‐tailored kinetics in confined crystallization, we crosslinked amorphous PB blocks in PEO‐b‐PB/PB with a photoinitiated crosslinking reaction to effectively suppress the cooperative crystallization. Small‐angle X‐ray scattering revealed that, in contrast to the noncrosslinked systems, the pre‐existing domain morphology in the melt was retained upon crystallization. The crystallization kinetics in the crosslinked system also exhibited a parallel transition with the morphological transformation, thereby verifying the existence of microdomain‐tailored kinetics in the confined crystallization of block copolymers. Homogeneous nucleation‐controlled crystallizations in cylindrical and spherical morphologies were demonstrated in an isothermal crystallization study in which the corresponding crystallinity developments followed a simple exponential rule not prescribed by conventional spherulitic crystallization. Despite the effective confinement imposed by the crosslinked PB phase, crystallization in the lamellar phase still proceeded through a mechanism analogous to the spherulitic crystallization of homopolymers. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 519–529, 2002; DOI 10.1002/polb.10121     

Effect of thermal history on the free volume properties of semi‐crystalline poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) membranes by positron annihilation lifetime spectroscopy

Free volume properties of a series of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) membranes, which were produced by various nonisothermal crystallization processes (rapid‐, step‐, and slow‐cooling processes), were investigated using positron annihilation lifetime (PAL) spectroscopy over a temperature range of 25–90 °C. From the annihilation lifetime parameters, the temperature dependence of free volume size, amount, size distribution, and fractional free volume and thermal expansion properties of free volume were discussed. A model which assumed that amorphous phase was subdivided into mobile and rigid amorphous fractions (MAF and RAF) in the semicrystalline polymer was considered to interpret the temperature dependence of those free volume properties. Morphological observation of the semicrystalline polymer by small‐angle X‐ray scattering (SAXS) indicated that the rapid‐cooled (cold‐crystallized) membranes showed a much thinner thickness of the repeating lamellar/amorphous layers and most likely higher amount of RAF, which restrained the chain motion, than the step‐ and slow‐cooled (melt‐crystallized) membranes. The difference of free volume properties among various PHBV membranes was created according to the crystalline structure of the polymer from different thermal history. The polymer crystallized with slower cooling rate induced higher crystallinity and resulted in less free volume amount and lower fractional free volume. In addition, the thermal expansion coefficients of free volume size were affected by the crystallization rate of PHBV polymer. Larger distribution of the free volume size of melt‐crystallized membranes was observed as a result of the bimodal distribution of the lamellar periodicity and less amount of RAF than that of the cold‐crystallized membranes. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 855–865, 2009     

Retardation Effect of Enzymatic Degradation of Microbial Polyesters at the Surface by Blending with Polystyrene

The enzymatic surface degradation behavior of the blend films of polystyrene (PS) with poly[((R)‐3‐hydroxybutyrate)‐co‐((L )‐3‐hydroxyvalerate)] (P(3HB‐co‐3HV)) or poly((R)‐3‐hydroxybutyrate (P(3HB)) were investigated using atomic force microscopy (AFM). It was found that the blends of PS with P(3HB‐co‐3HV) or P(3HB) are immiscible in both the amorphous and melt states. The degradation of both P(3HB‐co‐HV) and P(3HB) was significantly retarded at the initial stages of enzymatic attack by hydrophobic PS (up to 20 wt.‐%).     

Miscibility and crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) and methoxy poly(ethylene glycol) blends

Poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) (PHB‐HHx) and methoxy poly(ethylene glycol) (MPEG) blends were prepared using melt blending. The single glass transition temperature, T_g, between the T_gs of the two components and the negative χ value indicated that PHB‐HHx and MPEG formed miscible blends over the range of compositions studied. The Gordon–Taylor equation proved that there was an interaction between PHB‐HHx and MPEG in their blends. FTIR supported the presence of hydrogen bonding between the hydroxyl group of MPEG and the carbonyl group of PHB‐HHx. The spherulitic morphology and isothermal crystallization behavior of the miscible PHB‐HHx/MPEG blends were investigated at two crystallization temperatures (70 and 40 °C). At 70 °C, melting MPEG acted as a noncrystalline diluent that reduced the crystallization rate of the blends, while insoluble MPEG particles acted as a nucleating agent at 40 °C, enhancing the crystallization rate of the blends. However, no interspherulitic phase separation was observed at the two crystallization temperatures. The constant value of the Avrami exponent demonstrated that MPEG did not affect the three‐dimensional spherulitic growth mechanism of PHB‐HHx crystals in the blends, although the MPEG phase, such as the melting state or insoluble state, influenced the crystallization rate of the blends. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2852–2863, 2006     

Lamellar‐level morphology induced by combined crystallization and liquid–liquid demixing in a poly(ethylene terephthalate)/poly(ethylene‐2,6‐naphthalate) blend

The lamellar‐level morphology of an extruded poly(ethylene terephthalate) (PET)/poly(ethylene‐2,6‐naphthalate) (PEN) blend was investigated with small‐angle X‐ray scattering (SAXS). Measurements were made as a function of the annealing time in the melt and the crystallization temperature. The characteristic morphological parameters at the lamellar level were determined by correlation function analysis of the SAXS data. At a low crystallization temperature of 120 °C, the increased amorphous layer thickness was identified in the blend, indicating that some PEN was incorporated into the interlamellar regions of PET during crystallization. The blend also showed a larger lamellar thickness than pure PET. A reason for the increase in the lamellar thickness might be that the formation of thinner lamellar stacks by secondary crystallization was significantly restricted because of the increased glass‐transition temperature. At high crystallization temperatures above 200 °C, the diffusion rates of noncrystallizable components were faster than the growth rates of crystals, with most of the noncrystallizable components escaping from the lamellar stacks. As a result, the blend showed an interfibrillar or interspherulitic morphology. © 2002 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 317–324, 2002     

Compatibilizing effect of a graft copolymer on bacterial poly(3‐hydroxybutyrate)/poly(methyl methacrylate) blends

Blends of isotactic (natural) poly(3‐hydroxybutyrate) (PHB) and poly(methyl methacrylate) (PMMA) are partially miscible, and PHB in excess of 20 wt % segregates as a partially crystalline pure phase. Copolymers containing atactic PHB chains grafted onto a PMMA backbone are used to compatibilize phase‐separated PHB/PMMA blends. Two poly(methyl methacrylate‐g‐hydroxybutyrate) [P(MMA‐g‐HB)] copolymers with different grafting densities and the same length of the grafted chain have been investigated. The copolymer with higher grafting density, containing 67 mol % hydroxybutyrate units, has a beneficial effect on the mechanical properties of PHB/PMMA blends with 30–50% PHB content, which show a remarkable increase in ductility. The main effect of copolymer addition is the inhibition of PHB crystallization. No compatibilizing effect on PHB/PMMA blends with PHB contents higher than 50% is observed with various amounts of P(MMA‐g‐HB) copolymer. In these blends, the graft copolymer is not able to prevent PHB crystallization, and the ternary PHB/PMMA/P(MMA‐g‐HB) blends remain crystalline and brittle. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1390–1399, 2002     

Ring‐banded spherulites in poly(pentamethylene terephthalate): A model of waving and spiraling lamellae

A new aryl polyester, poly(pentamethylene terephthalate) (PPT) with five methylene groups in the repeat unit, was synthesized. Its multiple‐melting behavior and crystal structure were analyzed with differential scanning calorimetry and wide‐angle X‐ray diffraction. In addition, the spherulitic/lamellar morphology of melt‐crystallized PPT was investigated. Typical Maltese‐cross spherulites (with no rings) were seen in melt‐crystallized PPT at low temperatures (70–90 °C), but ring patterns were seen in PPT crystallized only at temperatures ranging from 100 to 115 °C, whereas rings disappeared with crystallization above 120 °C. The mechanisms of the rings in PPT were explained with several coordinated directional changes (wavy changes, twisting changes, and combinations) in the lamellae during growth. Scanning electron microscopy, in combination with atomic force microscopy, further proved that the ringed spherulites originated from the aggregation of sufficient numbers of edge‐on lamellar crystals; the radial‐growth edge‐on/flat‐on lamellae could be twisted and/or waved to form realistic band patterns. A postulated model properly described a possible origin of the ring bands through combined mechanisms of waving (zigzagging) and twisting (spiraling) of the lamellae during crystallization. Superimposed twisting and/or wavy models during crystallization were examined as examples. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4421–4432, 2004     

Structure and deformation recovery of the thermoplastic polyurethane spherulite

We investigated the structure and deformation behavior of the thermoplastic polyurethane (TPU) spherulite by optical microscopy, tensile testing, Hv light scattering, and small angle X‐ray scattering. The TPU spherulite structure obtained by melt crystallization was coarse consisting of bundle‐like structure containing hard segment (HS) lamellar domain in which the HS domains were stacked and the HS chain direction was perpendicular to the longitudinal axis of the HS domain. By stretching, the spherulite was deformed to ellipsoidal one and the stacked HS lamellar domains were tilted in the stretching direction. The deformed spherulite and the tilted HS domain in the spherulite were recovered to the unstretched state by retraction. The recovery of the structure is ascribed to the characteristic spherulite structure consisting of rubbery soft segment matrix physically cross‐linked with the stacked HS domain. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1585–1594     

Morphology development and crystallization behavior of poly(ethylene terephthalate)/phenoxy blend

The morphological development and crystallization behavior of a poly(ethylene terephthalate)/poly(hydroxyl ether of bisphenol A) (phenoxy) blend were studied with time‐resolved light scattering, optical microscopy, differential scanning calorimetry, and small‐angle X‐ray scattering (SAXS). During annealing at 280 °C, liquid–liquid phase separation via spinodal decomposition proceeded in the melt‐extruded specimen. After the formation of a domain structure, the blend slowly underwent phase homogenization by the interchange reactions between the two polymers. Specimens annealed for various times (t_s) at 280 °C were subjected to a temperature drop and the effects of liquid‐phase changes on crystallization were then investigated. The shifts in the position of the cold‐crystallization peaks indicated that the crystallization rate is associated with the composition change of the separated phases as well as the change of the sequence distribution in polymer chains during annealing. The morphological parameters at the lamellar level were determined by a correlation function analysis on the SAXS data. The crystal thickness (l_c) increased with t_s, whereas the amorphous layer thickness (l_a) showed little dependence on t_s. Observation of a constant l_a value revealed that a large number of noncrystallizable species formed by the interchange reactions between the two polymers were excluded from the lamellar stacks and resided in the interfibrillar regions, interspherulitic regions, or both. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 223–232, 2008     

New insight into melting and crystallization behavior in semicrystalline poly(ethylene terephthalate)

After isothermal crystallization, poly(ethylene terephthalate) (PET) showed double endothermic behavior in the differential scanning calorimetry (DSC) heating scan. During the heating scans of semicrystalline PET, a metastable melt which comes from melting thinner lamellar crystal populations formed between the low and the upper endothermic temperatures. The metastable melt can recrystallize immediately just above the low melting temperature and form thicker lamellae than the original ones. The thickness and perfection depends on the crystallization time and crystallization temperature. The crystallization kinetics of this metastable melt can be determined by means of DSC. The kinetics analysis showed that the isothermal crystallization of the metastable PET melt proceeds with an Avrami exponent of n = 1.0 ∼ 1.2, probably reflecting one‐dimensional or irregular line growth of the crystal occurring between the existing main lamellae with heterogeneous nucleation. This is in agreement with the hypothesis that the melting peaks are associated with two distinct crystal populations with different thicknesses. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 53–60, 2000     

Nucleation and Crystallization of PLDA-b-PE and PLLA-b-PE Diblock Copolymers

The nucleation and crystallization of two types of strongly segregated poly(lactide)-block-polyethylene diblock copolymers with an approximate 50/50 composition has been investigated. One material contains an amorphous PLDA block (PLDA-b-PE) and the other contains a semicrystalline PLLA block (PLLA-b-PE). The overall isothermal crystallization rate of the PLLA block was slowed down as compared to homo-PLLA by the covalently bonded PE chains that were molten at the PLLA crystallization temperatures. This crystallization rate depression of the PLLA block produces a coincident crystallization process when PLLA-b-PE is cooled down from the melt at rates larger than 2 °C/min. The overall crystallization rate of the PE block is faster when it is covalently bonded to previously crystallized PLLA than when it is attached to a rubbery PDLA block, this results from a nucleation effect of PLLA on the PE block. Polarized Light Optical Microscopy (PLOM) confirmed the confined nature of the crystallization process within lamellar microdomains for both diblock copolymers, since neither PLLA nor PE are capable of breaking out and spherulites can not be formed.     

Growth and kinetics of in vitro poly([R]‐(–)‐3‐hydroxybutyrate) granules interpreted as particulate polymerization with coalescence

Transmission electron microscopy (TEM) and Cryo‐TEM were used to study the growth kinetics of poly(3‐hydroxybutyrate) granules produced by in vitro polymerization. The in vitro formation of poly(3‐hydroxybutyrate) uses a recombinant form of the PHA synthase to polymerize [R]‐(–)‐3‐hydroxybutyryl‐CoA. Since the in vitro reaction contains only synthase and monomer, it is a simpler system than the in vivo biosynthesis of poly(3‐hydroxybutyrate). TEM and Cryo‐TEM were used in conjunction with image analysis to examine the granules that were formed in the in vitro reaction. The in vitro reaction yielded spherical granules of rapidly increasing size; the initially observed granules were already larger than 0.1 μm. While the average granule diameter and volume increased with reaction time, the number of granules decreased throughout the reaction due to coalescence. Basic kinetic parameters, including K_M and V_max were determined and compared to those reported for the in vivo biosynthesis of poly(3‐hydroxybutyrate). In addition it was found that the granules formed by this process were essentially noncrystalline. A computer simulation of the reaction, based on initial formation of relatively large microporous granules that consolidate by expulsion of water during polymerization, accounted for the shape of the kinetic curves.