Luminescence of CaGa<Subscript>2</Subscript>Se<Subscript>4</Subscript>:Eu crystals

We have studied photoluminescence and thermoluminescence (PL and TL) in CaGa₂Se₄:Eu crystals in the temperature range 77–400 K. We have established that broadband photoluminescence with maximum at 571 nm is due to intracenter transitions 4f⁶ 5d–4f⁷ (⁸S_7/2) of the Eu²⁺ ions. From the temperature dependence of the intensity (log I–10³/T), we determined the activation energy (E _a = 0.04 eV) for thermal quenching of photoluminescence. From the thermoluminescence spectra, we determined the trap depths: 0.31, 0.44, 0.53, 0.59 eV. The lifetime of the excited state 4f6 5d of the Eu²⁺ ions in the CaGa₂Se₄ crystal found from the luminescence decay kinetics is 3.8 μsec. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 76, No. 1, pp. 112–116, January–February, 2009.     

Ion conduction and space-charge polarization processes in Li<Subscript>2</Subscript>Ge<Subscript>7</Subscript>O<Subscript>15</Subscript> crystals

The electrical properties of a lithium heptagermanate (Li₂Ge₇O₁₅) crystal have been studied in DC and AC measuring fields at temperatures from 500 to 700 K. In a DC field, a substantial decrease of electrical conductivity σ with time has been detected. On the basis of kinetic dependences σ(t), estimates of the charge carrier diffusion coefficient D have been obtained. In the frequency range 10¹–10⁵ Hz, the spectra of complex impedance ρ*(f) have been measured. The analysis of diagrams in the complex plane (ρ″–ρ′) has been performed within the equivalent circuit approach. It has been shown that, in the considered temperature and frequency intervals, the electrical properties of Li₂Ge₇O₁₅ crystals have been determined by the hopping conduction of interstitial lithium ions A _Li and accumulation of charge carriers near the blocking Pt electrodes.     

Polarization modes in the Ba<Subscript>2</Subscript>Mg<Subscript>2</Subscript>Fe1<Subscript>2</Subscript>O<Subscript>22</Subscript> multiferroic

The spectra of complex permittivity of a Ba₂Mg₂Fe₁₂O₂₂ single crystal belonging to the family of Y-type hexaferrites have been measured over a wide temperature range (10–300 K) with the aim of determining the dynamic parameters of the phonon and magnetic subsystems in the terahertz and infrared frequency ranges (3–4500 cm⁻¹). A factor-group analysis of the vibrational modes has been performed, and the results obtained have been compared with the experimentally observed resonances. The oscillator parameters of all nineteen phonon modes of E _u symmetry, which are allowed by the symmetry of the Ba₂Mg₂Fe₁₂O₂₂ crystal lattice, have been calculated. It has been found that, at temperatures below 195 and 50 K, the spectral response exhibits new absorption lines due to magnetic excitations.     

NMR study and electrical properties investigation of Zn<Subscript>2</Subscript>P<Subscript>2</Subscript>O<Subscript>7</Subscript>

The α-Zn₂P₂O₇ compound was obtained by conventional solid-state reaction. The sample was characterized by X-ray powder diffraction, solid state ³¹P NMR MAS, and electrical impedance spectroscopy. The solid state ³¹P MAS NMR, performed at 121.49 MHz, shows three isotropic resonances at −21.1, −18.8, and −15.8 ppm, confirming the non-equivalency of the three PO₄ groups in the α-Zn₂P₂O₇ form. They are characterized by different chemical shift tensor parameters with the local geometrical features of the tetrahedra. Electrical impedance measurements of β-Zn₂P₂O₇, form stable for temperature greater than 403 K, were performed as a function of both temperature and frequency. The electrical conduction and dielectric relaxation have been studied. The AC conductivity obeys the universal power law. The approximation type correlated barrier hopping model explains the universal behavior of the n exponent. The impedance plane plot shows semicircle arcs at different temperatures, and an electrical equivalent circuit has been proposed to explain the impedance results. The circuits consist of the parallel combination of bulk resistance R _p and constant phase elements CPE. The simulated spectra show a good correlation with the experimental data.     

Spectral and kinetic characteristics of CdI<Subscript>2</Subscript> and CdI<Subscript>2</Subscript>:Pb scintillators

We have studied the effect of lead dopant on the optical absorption, photoluminescence, and x-ray luminescence spectra, and the scintillation characteristics of CdI₂ at room temperature. The crystals for the study were grown by the Stockbarger-Bridgman method. Activation of CdI₂ from the melt by the compound PbI₂ leads to the appearance in the absorption spectra in the near-edge region of an activator band at 395–405 nm, which is interpreted as an A band connected with electronic transitions from the ¹S₀ state to the ³P₁ levels in the Pb²⁺ ion. For x-ray excitation, CdI₂:Pb²⁺ crystals with optimal dopant concentration (∼1.0 mol%) are characterized by a light yield with maximum in the 570–580 nm region that is an order of magnitude higher than for CdI₂ crystals in the 490–500 nm band. For α excitation, the radioluminescence kinetics for cadmium iodide is characterized by a very short (∼0.3 nsec) rise time and fast decay of luminescence, with τ₁ ≈ 4 nsec and τ₂ = 10–76 nsec. Depending on the conditions under which the crystals were obtained, the fast component fraction is 95%–99%. The crystal is characterized by a similar scintillation pulse in the case of excitation by x-ray pulses. The radioluminescence pulse shape for CdI₂:Pb in the decay stage is predominantly exponential, with luminescence decay time constants τ₁ ≈ 10 nsec and τ₂ = 200–250 nsec. This system is characterized by low afterglow, at the level for the Bi₄G₃O₁₂ scintillator. We have demonstrated the feasibility of using CdI₂:Pb as a scintillator for detecting α particles. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 75, No. 6, pp. 825–830, November–December, 2008.     

Electrical properties,equivalent circuit,and dielectric relaxation studies on [(C<Subscript>3</Subscript>H<Subscript>7</Subscript>)<Subscript>4</Subscript>N]<Subscript>2</Subscript>Cd<Subscript>2</Subscript>Cl<Subscript>6</Subscript> polycrystalline

The Ac electrical conductivity and the dielectric relaxation properties of the [(C₃H₇)₄N]₂Cd₂Cl₆ polycrystalline sample have been investigated by means of impedance spectroscopy measurements over a wide range of frequencies and temperatures, 209 Hz–5 MHz and 361–418 K, respectively. The purpose is to make a difference between the electrical and dielectric properties of the polycrystalline sample and single crystal. Besides, a detailed analysis of the impedance spectrum suggests that the electrical properties of the material are strongly temperature-dependent. Plots of (Z" versus Z') are well fitted to an equivalent circuit model consisting of a series combination of grains and grains boundary elements. Moreover, the temperature dependence of the electrical conductivity in the different phases follows the Arrhenius law and the frequency dependence of σ (ω) follows the Jonscher’s universal dynamic law. Furthermore, the modulus plots can be characterized by full width at half height or in terms of a nonexperiential decay function φ(t) = exp(t/t)^β. Finally, the imaginary part of the permittivity constant is analyzed with the Cole–Cole formalism.     

Tunable bluish green to yellowish green Ca<Subscript>2(1-x)</Subscript>Sr<Subscript>2x</Subscript>Al<Subscript>2</Subscript>SiO<Subscript>7</Subscript>:Eu<Superscript>2+</Superscript> phosphors for potential LED application

A series of solid solutions with a general formula of Ca_2(1-x)Sr_2xAl₂SiO₇:Eu²⁺ were synthesized by a high temperature solid state reaction. The structure, diffuse reflection spectra, photoluminescence spectra, color-coordinate parameters and lifetimes of phosphors were investigated. XRD results show that Ca₂Al₂SiO₇ is totally miscible with Sr₂Al₂SiO₇. These solid solution phosphors show a broad excitation band of 350–450 nm that matches well with the output lights of near-UV LEDs and tunable emission from bluish green to yellowish green. These optical properties originate from the 4f⁷–4f⁶5d transition of Eu²⁺ ions. The crystal field strength was considered to be tailed by controlling the host composition, which leads to the shift of absorption band and emission band, and the varying of color coordinates. PACS  78.55.-m; 42.70.-a; 61.05.C-     

Magnetic properties of LiNi<Subscript>0.5</Subscript>Mn<Subscript>0.47</Subscript>Al<Subscript>0.03</Subscript>O<Subscript>2</Subscript> as positive electrode for Li-ion batteries

The layered LiNi_0.5Mn_0.47Al_0.03O₂ was synthesized by wet chemical method and characterized by X-ray diffraction and analysis of magnetic measurements. The powders adopted the α-NaFeO₂ structure. This substitution of Al for Mn promotes the formation of Li(Ni_0.47²⁺Ni_0.03³⁺Mn_0.47⁴⁺Al_0.03³⁺)O₂ structures and induces an increase in the average oxidation state of Ni, thereby leading to the shrinkage of the lattice unit cell. The concentration of antisite defects in which Ni²⁺ occupies the (3a) Li lattice sites in the Wyckoff notation has been estimated from the ferromagnetic Ni²⁺(3a)–Mn⁴⁺(3b) pairing observed below 140 K. The substitution of 3% Al for Mn reduces the amount of antisite defects from 7% to 6.4–6.5%. The analysis of the magnetic properties in the paramagnetic phase in the framework of the Curie–Weiss law agrees well with the combination of Ni²⁺ (S = 1), Ni³⁺ (S = 1/2) and Mn⁴⁺ (S = 3/2) spin-only values. Delithiation has been made by the use of K₂S₂O₈. According to this process, known to be softer than the electrochemical one, the nickel ions in the (3b) sites are converted into Ni⁴⁺ in the high spin configuration, while Ni²⁺(3a)–Mn⁴⁺(3b) ferromagnetic pairs remain, as the Li⁺(3b) ions linked to the Ni²⁺(3a) ions in the antisite defects are not removed. The results show that the antisite defect is surrounded by Mn⁴⁺ ions, implying the nonuniform distribution of the cations in agreement with previous NMR and neutron experiments.     

Synthesis and nanostructural investigation of TiO<Subscript>2</Subscript> nanorods doped by SiO<Subscript>2</Subscript>

TiO₂ Nano rods can be used as dye-sensitized solar cells, various sensors and photocatalysts. These nanorods are synthesized by a hydrothermal corrosion process in NaOH solution at 200°C using TiO₂ powder as the source material. In the present work, the synthesis of TiO₂ nanorods in anatase, rutile and Ti₇O₁₃ phases and synthesis of TiO₂ nanorods by incorporating SiO₂ dopant, using the sol–gel method and alkaline corrosion are reported. The morphologies and crystal structures of the TiO₂ nanorods are characterized using field emission scanning electron microscopy (FE-SEM), atomic force microscopy (AFM) and X-ray diffraction (XRD) study. The obtained results show not only an aggregation structure at high calcination temperatures with spherical particles but also Ti–O–Si bonds having four-fold coordination with oxygen in SiO^4 −.     

Anti-stokes luminescence of solid AgCl<Subscript>0.95</Subscript>I<Subscript>0.05</Subscript> solutions

An anti-Stokes luminescence band with λ_max = 515 nm of microcrystals of solid AgCl_0.95I_0.05 solutions excited by a radiation flux of density 10¹³–10¹⁵ quanta/cm²·sec in the range 600–800 nm at 77 K was detected. It is shown that the intensity of this luminescence and the frequency of its excitation depend on the prior UV-irradiation of samples. Analysis of the stimulated-photoluminescence spectra and the anti-Stokes luminescence excitation spectra of the indicated microcrystals has shown that to the centers of anti-Stokes luminescence excitation correspond local levels in the forbidden band of the crystals. These states are apparently due to the atomic and molecular disperse silver particles that can be inherent in character or formed as a result of a low-temperature photochemical process. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 72, No. 6, pp. 738–742, November–December, 2005.     

Optical absorption spectra and magnetic phase transitions in TbFe<Subscript>3</Subscript>(BO<Subscript>3</Subscript>)<Subscript>4</Subscript>

Optical absorption spectra of the trigonal crystal of TbFe₃(BO₃)₄ in the vicinity of the ⁷F₆ → ⁵D₄ transition in a Tb³⁺ ion were studied as a function of temperature (2–70 K) and magnetic field strength (0–60 kOe) at 2 K. The splitting of the excited states of Tb³⁺ due to both the magnetic ordering of iron and an external magnetic field was determined. Abrupt splitting of the absorption lines of Tb³⁺ at temperature T_N of the magnetic ordering of the subsystem of iron was revealed, suggesting that the nature of such splitting is not entirely magnetic.     

Preparation and characterization of the polymer electrolyte system ENR50/PVC/EC/PC/LiN(CF<Subscript>3</Subscript>SO<Subscript>2</Subscript>)<Subscript>2</Subscript> for electrochemical device applications

Polymer electrolytes containing epoxidised natural rubber (ENR50)/poly(vinyl chloride) (PVC) blend as a polymer host, a solvent mixture of ethylene carbonate (EC) and propylene carbonate (PC) as a plasticizer, and lithium imide, LiN (CF₃SO₂)₂, as a salt were studied. Polymer electrolytes that were obtained by solvent cast yielded solid dry rubbery films with a thickness range of 110–125 μm. Impedance spectroscopy, Fourier transform infra red (FTIR) spectroscopy, differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) were performed on these samples. The prepared solid polymer electrolytes exhibit ionic conductivities in the order 10⁻⁴ S cm⁻¹ at room temperature as expected. However, the physical properties of the electrolytes have improved significantly when optimal composition has been selected. Paper presented at the International Conference on Solid State Science and Technology 2006, Kuala Terengganu, Malaysia, Sept. 4–6, 2006.     

Synthesis and luminescent properties of Eu<Superscript>3+</Superscript>- and Eu<Superscript>2+</Superscript>-activated sodium pyrophosphate Na<Subscript>4</Subscript>P<Subscript>2</Subscript>O<Subscript>7</Subscript>

The luminescent properties of Eu³⁺ and Eu²⁺ ions in sodium pyrophosphate, Na₄P₂O₇, have been studied. The excitation spectrum of the Eu³⁺ emission in Na₄P₂O₇ consists of several sets of bands in the range 280–535 nm due to 4f–4f transitions of Eu³⁺ ions and a broad band with a maximum at about 240 nm interpreted to be due to a charge transfer (CT) transition from oxygen 2p states to empty states of the Eu³⁺ 4f⁶-configuration. Although the CT band energy is large enough, the quantum efficiency (η) of the Eu³⁺ emission in Na₄P₂O₇ under CT excitation was estimated to be very low (η ≤ 0.01). In terms of a configurational coordinate model, this fact is interpreted as a result of the high efficiency of a radiationless relaxation from the CT state to the ⁷F₀ ground state of Eu³⁺ ions occupying sodium sites in Na₄P₂O₇. A strong reducing agent is required in order to stabilize Eu²⁺ ions in Na₄P₂O₇ during the synthesis. Several nonequivalent Eu²⁺ luminescence centers in Na₄P₂O₇ were found.     

Electrical characterization of the [N(CH<Subscript>3</Subscript>)<Subscript>4</Subscript>][N(C<Subscript>2</Subscript>H<Subscript>5</Subscript>)<Subscript>4</Subscript>]ZnCl<Subscript>4</Subscript> compound

The [N(CH₃)₄][N(C₂H₅)₄]ZnCl₄ compound has been synthesized by a solution-based chemical method. The X-ray diffraction study at room temperature revealed an orthorhombic system with P2₁2₁2 space group. The complex impedance has been investigated in the temperature and frequency ranges 420–520 K and 200 Hz–5 MHz, respectively. The grain interior and grain boundary contribution to the electrical response in the material have been identified. Dielectric data were analyzed using the complex electrical modulus M ^* for the sample at various temperature. The modulus plots can be characterized by full width at half height or in terms of a non-exponential decay function ϕ(t) = exp[(−t/τ) ^β ]. The detailed conductivity study indicated that the electrical conduction in the material is a thermally activated process. The variation of the AC conductivity with frequency at different temperatures obeys the Almond and West universal law.     

Preparation of nanosized Bi<Subscript>2</Subscript>WO<Subscript>6</Subscript> using different content of starting materials and their photoactivities

A series of nanosized Bi₂WO₆ catalysts was synthesized using various starting materials, and they were characterized by X-ray diffractometry, transmission electron microscopy, and diffuse reflectance spectroscopy. Rhodamine-B (RhB) photodegradation in aqueous medium was employed as a probe reaction to test the photoactivity of the as-prepared samples. Dependence of the photocatalytic activities on different contents of the starting materials was examined under visible irradiation (λ > 400 nm). The sample prepared in the following conditions: reaction time 24 h, the pH of the solution 7, the Bi³⁺ amount in the start precipitates 5 mmol — exhibited the highest photochemical activity when the hydrothermal temperature was settled at 180°C. Published in Zhurnal Prikladnoi Spektroskopii, Vol. 76, No. 2, pp. 243–249, Martch–April, 2009.     

Broadband infrared luminescence from transparent glass–ceramics containing Ni<Superscript>2+</Superscript>-doped <Emphasis Type="BoldItalic">β</Emphasis> -Ga<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocrystals

Transparent Ni²⁺-doped β-Ga₂O₃ glass–ceramics were synthesized. The nanocrystal phase in the glass–ceramics was identified to be β-Ga₂O₃ and its size was about 3.6 nm. It was confirmed from the absorption spectra that the ligand environment of Ni²⁺ ions changed from the trigonal bi-pyramid fivefold sites in the as-cast glass to the octahedral sites in the glass–ceramics. The broadband infrared emission centering at 1270 nm with full width at half maximum (FWHM) of more than 250 nm was observed. The fluorescence lifetime was about 1.1 μs at room temperature. The observed infrared emission could be attributed to the ³ T _2g (³ F )→³ A _2g (³ F ) transition of octahedral Ni²⁺ ions. It is suggested that the Ni²⁺-doped transparent β-Ga₂O₃ glass–ceramics with broad bandwidth and long lifetime have a potential as a broadband amplification medium. PACS 42.70.-a; 42.70.Ce; 81.40.Tv     

Improvement of the intergranular pinning energy in uniaxially compacting (Bi-Pb)<Subscript>2</Subscript>Sr<Subscript>2</Subscript>Ca<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>10+δ</Subscript> ceramic samples

Measurements of the electrical resistivity as a function of temperature, ρ(T), for different values of applied magnetic field, B_a (0 ≤ B_a ≤ 50 mT), were performed in polycrystalline samples of Bi_1.65Pb_0.35Sr₂Ca₂ Cu₃O_10+δ subjected to different uniaxial compacting pressure (UCP). We have found appreciable differences in the grain orientation between samples by using X-ray diffractometry. From the X-ray diffraction patterns performed, in powder and pellet samples, we have estimated the Lotgering factor along the (00l) direction, F_(00l). The results indicate that F_(00l) increases ~23% with increasing UCP suggesting that grains of these samples are preferentially aligned along the c-axis, which is parallel to the compacting direction. The resistive transition of the samples have been interpreted in terms of the thermally activated flux-creep model. In addition, the effective intergranular pinning energy, U₀, have been determined for different applied magnetic field. The magnetic field dependence of U₀, for B_a > 8 mT, was found to follow a H^{- α} dependence with α = 0.5 for all samples. The analysis of the experimental data strongly suggested that increasing UCP results in appreciable changes in both the grain alignment and the grain connectivity of the samples. We have successfully interpreted the data by considering the existence of three different superconducting levels within the samples: the superconducting grains, the weak-links, and the superconducting clusters.     

Photoluminescence of nanoparticles of (Ga<Subscript>2</Subscript>S<Subscript>3</Subscript>)<Subscript>0.95</Subscript>(Eu<Subscript>2</Subscript>O<Subscript>3</Subscript>)<Subscript>0.05</Subscript> solid solution

We have ground bulk samples to obtain nanoparticles of (Ga₂S₃)_1–x (Eu₂O₃) _x solid solutions, the sizes of which were determined using an atomic force microscope. The photoluminescence spectra of the nanoparticles were studied in the temperature interval 77–300 K. We have established the mechanisms for emission and transfer of energy from the matrix to the rare-earth ion, and we determined the Stokes shift (ΔS = 0.7 eV), the Huang–Rhys parameter (S = 16), and the optical phonon energy (ħ−ω = 23 meV).     

Spectral-luminescent investigations of glasses and glass-ceramic materials in Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-GeO<Subscript>2</Subscript>-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> system

Glasses of 2Bi₂O₃-3GeO₂-xFe₂O₃ composition, where x = 0–1.5, are obtained under oxidizing and reducing conditions. Glass-ceramic materials are produced by the thermal treatment of the glasses, the properties of which, as well as those of the original glasses, are studied by the methods of X-ray phase analysis and optical and luminescent spectroscopy. It is found that the Fe³⁺/Fe²⁺ ion ratio in the samples changes depending on the synthesis conditions of the original glasses and crystallization process.     

Investigation of ion transport in Li<Subscript>8</Subscript>ZrO<Subscript>6</Subscript> and Li<Subscript>6</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript> solid electrolytes

Lithium ionic conductivity and spin-lattice relaxation rates were measured in Li₈ZrO₆ and Li₆Zr₂O₇ solid electrolytes. It was found that the Li₈ZrO₆ solid electrolyte undergoes a transition to the superionic state in the temperature range 673–703 K. It was shown that Li⁺ ions are mobile in particular lattice positions of the Li₆Zr₂O₇ phase, and that ionic conductivity is monotonic at an activation energy of 79.4 kJ/mol.