Surface modification of indium tin oxide anode with self-assembled monolayer modified Ag film for improved OLED device characteristics

Modification of electrodes has attracted much attention in the study of organic semiconductor devices. A self-assembled monolayer (SAM) of 4-fluorothiophenol is employed to modify the Ag film on the surface of indium tin oxide (ITO) to improve the hole injection and the surface morphology. The modified anode was characterized by X-ray photoelectron spectroscopy (XPS), atomic force microscope (AFM), and UV–vis transmittance spectra. To investigate the effect of the modification on the device characteristics, typical double layer devices with the structure of anode/-naphthylphenylbiphenyl diamine (NPB, 60 nm)/tris-(8-hydroxyquinoline) aluminum (Alq₃, 60 nm)/LiF(0.7 nm)/Al(100 nm) were fabricated using the modified anode and the bare ITO. The effect of Ag layer thickness on the device performance is also investigated. The results revealed that SAM modified ultra-thin Ag film is an effective buffer layer for organic light emitting diode. The device using the ITO/Ag (5 nm)/SAM as anode show improved device characteristics than that of using bare ITO as anode. The enhancements in luminance and efficiency are attributed to enhanced hole injection and smooth surface between anode and the organic material. The Ag thickness of 5 nm is chosen as an acceptable compromise between substrate transparency and the device performance.     

Strain due to nickel diffusion into hydrogen-terminated Si(1 1 1) surface

We studied the affection of thin (i.e., 0.2–0.8 nm) Ni films on hydrogen-terminated Si(1 1 1) substrate surface by using strain-sensitive X-ray diffraction. It was reported that Ni deposition onto hydrogen-terminated Si surface apparently does not cause film growth, but rather diffuses into the Si crystal, creating an “Ni diffusion layer” up to Ni deposition 0.8 nm thick. Measured rocking curves of the Si 1 1 3 reflection and integrated intensities of the rocking curves for the substrate provide information about the evolution of the strain field introduced near the substrate surface during Ni diffusion into the substrate. Comparing the measured and calculated rocking curves indicates that compression of the {1 1 1} spacing of the Si occurs gradually up to an Ni thickness of 0.6 nm, and that above this thickness, strain relaxation occurs.

We found that the slope of the integrated intensity of the rocking curve versus X-ray wavelength correlates to the strain field near the surface, in the same way that the shape of the rocking curves correlate to the strain field near the surface. Dynamical diffraction calculations indicate that measurement of the slope of the integrated intensity of the rocking curve versus X-ray wavelength is useful for strain analysis, because the dependence is not only sensitive to strain fields, but is also insensitive to the effect of absorption by the overlayer, which otherwise would cause deformation of the shape of the rocking curve.     

Coating zinc oxide submicron crystals on poly(methyl methacrylate) chips and spheres via ultrasound irradiation

Ultrasound irradiation is used for anchoring zinc oxide submicron crystals with a main diameter and length of 280 nm and 470 nm, respectively, onto the surface of poly(methyl methacrylate) PMMA chips (2 mm diameter), and zinc oxide crystals with a mean diameter and length of 150 nm and 230 nm, respectively, onto the surface of the PMMA spheres (1–10 μm). The zinc oxide crystals were obtained by sonochemical irradiation of a mixture containing the PMMA, zinc (II) acetate dihydrate, ethanol, water, and 24 wt.% aqueous ammonia for 2 h, yielding a PMMA–zinc oxide composite. By controlling the atmosphere and reaction conditions, we could achieve well-adhered zinc oxide crystals on the surface of poly(methyl methacrylate). The resulting zinc oxide–PMMA composite was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), energy-dispersive X-ray analysis (EDX), high-resolution scanning electron microscopy (HRSEM), and photoluminescence (PL) spectroscopy. The zinc oxide-deposited PMMA chips (loaded with 0.03–1.0 wt.% ZnO) were successfully homogenized in melt by extrusion and then injection molded into small, disc-shaped samples. These samples were analyzed with respect to their directional spectral optical properties in UV, Vis and IR spectroscopy.     

STM and LEED observations of erbium silicide nanostructures grown on Si(1 0 0) surface: atomic-scale understandings

In this work, erbium silicide is grown on the Si(1 0 0) surface by depositing Er onto the substrate and annealing at 600–700 °C. Many nanowires of Er silicide are formed with lengths in the range 10–100 nm. The formation and evolution of this nanostructure are investigated at atomic scale directly with scanning tunneling microscopy and low-energy electron diffraction. The direction of these nanowires is found perpendicular to that of Si dimer rows. It is shown that Er coverage and annealing temperature have an effect on the formation of nanowires. On the surface between nanowires, new (5×2) and c(5×4) reconstructions are observed, giving an implication to understand the growth behaviors of Er silicide on Si(1 0 0) surface.     

Enhanced dispersion and stability of gold nanoparticles on stoichiometric and reduced TiO2(1 1 0) surface in the presence of molybdenum

Mo, Au and their coadsorbed layers were produced on nearly stoichiometric and oxygen-deficient titania surfaces by physical vapor deposition (PVD) and characterized by low energy ion scattering (LEIS), X-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy (AES) and scanning tunnelling microscopy (STM). The behavior of Au/Mo bimetallic layers was studied at different relative metal coverages and sample temperatures.

STM data indicated clearly that the deposition of Au on the Mo-covered stoichiometric TiO₂(1 1 0) surface results in an enhanced dispersion of gold at 300 K. The mean size of the Au nanoparticles formed at 300 K on the Mo-covered TiO₂(1 1 0) was significantly less than on the Mo-free titania surface (2 ± 0.5 nm and 4 ± 1 nm, respectively). Interestingly, the deposition of Mo at 300 K onto the stoichiometric TiO₂(1 1 0) surface covered by Au nanoparticles of 3–4 nm (0.5 ML) also resulted in an increased dispersity of gold. The driving force for the enhanced wetting at 300 K is that the Au–Mo bond energy is larger than the Au–Au bond energy in 3D gold particles formed on stoichiometric titania. In contrast, 2D gold nanoparticles produced on ion-sputtered titania were not disrupted in the presence of Mo at 300 K, indicating a considerable kinetic hindrance for breaking of the strong Au-TiO_x bond.

The annealing of the coadsorbed layer formed on a strongly reduced surface to 740 K did not cause a decrease in the wetting of titania surface by gold. The preserved dispersion of Au at higher temperatures is attributed to the presence of the oxygen-deficient sites of titania, which were retained through the reaction of molybdenum with the substrate. Our results suggest that using a Mo-load to titania, Au nanoparticles can be produced with high dispersion and high thermal stability, which offers the fabrication of an effective Au catalyst.     

Structural and optical features of nanoporous silicon prepared by electrochemical anodic etching

Nanoporous silicon (NPS) samples were prepared by electrochemical anodic etching of p-type (0 0 1) silicon wafers in HF solution, and some of them were aged in air. The nanostructural, optical and chemical features of the NPS were investigated in terms of etching and aging conditions. The surface of the porous Si exhibits an etched layer with a thickness of 30–40 nm; this layer appears to consist of aggregates of 5–10 nm size nano-crystallites. The NPS exhibited broad photoluminescence (PL) spectra with its peak in the red light region (740 nm). After aging the porous samples for 4 weeks in air, we observed the PL intensity became approximately a fifth of that of the as-prepared one, along with a blue shift. It is very likely that the blue shift of the PL peak was caused by the shrinkage of the Si nano-crystallites due to the oxidation in the surface of the nano-crystallites.     

Coercive field behavior of permalloy antidot arrays based on self-assembled template fabrication

High-density magnetic antidot arrays have been fabricated by deposition of Fe₂₀Ni₈₀ thin films on self-assembled nanoporous alumina membranes (NAM) with high-order hexagonal symmetry. The magnetic properties induced by the size and the geometry configuration of the holes introduced in a Fe₂₀Ni₈₀ thin film are discussed based on hysteresis loops measured as a function of temperature. The precursor NAMs have pore diameters ranging between 35 and 95 nm (55 and 75 nm after the film deposition) and a lattice parameter of 105 nm. An enormous increase of coercitivity, as compared with the corresponding continuous films, was observed for temperatures between 2 and 300 K. This effect depends on the size and surface density of holes in the Fe₂₀Ni₈₀ antidot arrays. Rutherford backscattering spectrometry (RBS) measurements were performed in order to better clarify the magnetic material that was eventually deposited within the NAM pores.     

Method for independent control of particle size and distance in rhodium epitaxy on TiO2(110)-(1×2) surface An STM study

A method for independent control of the particle size and distance is presented for rhodium epitaxy on TiO₂(110)-(1×2) surface. The real space imaging of the surface morphology was performed by scanning tunneling microscopy. The amount of the deposited rhodium was checked by Auger electron spectrometry. The method consists of two steps: (i) evaporation of 0.001–0.050 ML equivalent of rhodium at room temperature with a post-annealing at 1100 K (“seeding”); (ii) post-deposition of rhodium for growing of the Rh nanoparticles formed in step (i) (“growing”). The mechanism of this procedure is based on the large difference of the surface diffusion coefficient between Rh adatoms and Rh nanocrystallites larger than 1–2 nm. In the first step the average distance between the metal particles is controlled in the range 5–200 nm, the second step determines the particles size (2–50 nm). This work demonstrates that the diffusion processes of metal nanoparticles of different sizes and the growing modes of the crystallites can be studied in detail by application of seeded surfaces.     

Vanadium oxide nanostructures on Rh(1 1 1): Promotion effect of CO adsorption and oxidation

The adsorption of CO and the reaction of CO with pre-adsorbed oxygen at room temperature has been studied on the (2 × 1)ORh(1 1 1) surface and on vanadium oxideRh(1 1 1) “inverse model catalyst” surfaces using scanning tunnelling microscopy (STM) and core-level photoemission with synchrotron radiation. Two types of structurally well-defined model catalyst V₃O₉Rh(1 1 1) surfaces have been prepared, which consist of large (mean size of 50 nm, type I model catalyst) and small (mean size <15 nm, type II model catalyst) two-dimensional oxide islands and bare Rh areas in between; the latter are covered by chemisorbed oxygen. Adsorption of CO on the oxygen pre-covered (2 × 1)ORh(1 1 1) surface leads to fast CO uptake in on-top sites and to the removal of half (0.25 ML) of the initial oxygen coverage by an oxidation clean-off reaction and as a result to the formation of a coadsorbed (2 × 2)O + CO phase. Further removal of the adsorbed O with CO is kinetically hindered at room temperature. A similar kinetic behaviour has been found also for the CO adsorption and oxidation reaction on the type I “inverse model catalyst” surface. In contrast, on the type II inverse catalyst surface, containing small V-oxide islands, the rate of removal of the chemisorbed oxygen is significantly enhanced. In addition, a reduction of the V-oxide islands at their perimeter by CO has been observed, which is suggested to be the reason for the promotion of the CO oxidation reaction near the metal-oxide phase boundary.     

Adsorption of oxygen and carbon dioxide on cesium-reconstructed Ag(1 1 0) surface

The adsorption of oxygen and carbon dioxide on cesium-reconstructed Ag(1 1 0) surface has been studied with scanning tunneling microscopy (STM) and temperature programmed desorption (TPD). At 0.1 ML Cs coverage the whole surface exhibits a mixture of (1 × 2) and (1 × 3) reconstructed structures, indicating that Cs atoms exert a cooperative effect on the surface structures. Real-time STM observation shows that silver atoms on the Cs-covered surface are highly mobile on the nanometer scale at 300 K. The Cs-reconstructed Ag(1 1 0) surface alters the structure formed by dissociative adsorption of oxygen from p(2 × 1) or c(6 × 2) to a p(3 × 5) structure which incorporates 1/3 ML Ag atoms, resulting in the formation of nanometer-sized (10–20 nm) islands. The Cs-induced reconstruction facilitates the adsorption of CO₂, which does not adsorb on unreconstructed, clean Ag(1 1 0). CO₂ adsorption leads to the formation of locally ordered (2 × 1) structures and linear (2 × 2) structures distributed inhomogeneously on the surface. Adsorbed CO₂ desorbs from the Cs-covered surface without accompanied O₂ desorption, ruling out carbonate as an intermediate. As a possible alternative, an oxalate-type surface complex [OOC–COO] is suggested, supported by the occurrence of extensive isotope exchange between oxygen atoms among CO₂(a). Direct interaction between CO₂ and Cs may become significant at higher Cs coverage (>0.3 ML).     

Investigation of phosphorus surface segregation by X-ray scattering measurements

The surface segregation of phosphorus in silicon at low temperatures is studied by using δ doping structures grown by molecular beam epitaxy. The samples are characterized by X-ray crystal truncation rod (CTR) scattering using synchrotron radiation as the light source. The 1/e decay length of P segregation and segregation barrier energy are obtained by fitting the CTR curves within kinematical approximation of X-ray diffraction theory. The surface segregation of P is strong at a growth temperature of 450 °C, with a 1/e decay length of 14 nm, while for growth temperatures below 350 °C, P segregation is negligible with a 1/e decay length not larger than 4 nm. The segregation barrier energy is determined to be 0.43 eV.     

Growth of metallic nanowires on anisotropic Si substrates: Pb on vicinal Si(0 0 1), Si(7 5 5), Si(5 3 3), and Si(1 1 0)

The spontaneous formation of mesoscopic Pb-wires, on 4° off-cut Si(0 0 1) vicinal surface, Si(7 5 5), Si(5 3 3), and Si(1 1 0) substrates was studied by low-energy electron microscopy. Before the deposition of Pb the substrates were modified by predeposition of a submonolayer amount of Au followed by annealing. The Au-induced reconstruction creates quasi-one-dimensional facets and superstructures. Their width ranged from several hundred nm in the case of the vicinal Si(0 0 1) down to atomic scale size, for the Si(1 1 0) surface. The best-developed arrays of parallel aligned mesoscopic wires were obtained during the deposition of Pb on substrates cooled slightly below room temperature. Wires with length to width ratio reaching 130 were produced on the Si(7 5 5) and the Si(5 3 3) substrates. The width of these nanowires was uniform over the whole substrate and was about 60 nm. The driving forces for the formation of the mesoscopic wires are the anisotropic strain due to the large misfit between the Pb and the Si lattice and one-dimensional diffusion of Pb.     

The effect of thickness and annealing condition on the microstructure and magnetic properties of Fe/Pt multilayer thin films

[Fe(0.5 nm)/Pt(0.5 nm)]₄₀, [Fe(1 nm)/Pt(1.5 nm)]₂₀ and [Fe(3 nm)/Pt(3 nm)]₁₀ multilayer were prepared by DC magnetron sputtering. By conventional furnace annealing (CA) at 270–600 °C for various time, all of the films still remained the disordered structure with the soft magnetic phase. By rapid thermal annealing (RTA) at 500 °C for various time, we obtained the [Fe(1 nm)/Pt(1.5 nm)]₂₀ and [Fe(3 nm)/Pt(3 nm)]₁₀ films with L1₂ ordered FePt₃ phase which was almost ferromagnetic at room temperature. However, the [Fe(0.5 nm)/Pt(0.5 nm)]₄₀ films was still disordered state even under RTA. Compared with CA, RTA exposed an outstanding effect on accelerating the phase transition when the film thickness is over [Fe(0.5 nm)/Pt(0.5 nm)]₄₀.     

Regular step formation on concave-shaped surfaces on 6H–SiC(0 0 0 1)

A concave-shaped surface has been prepared in a 6H–SiC(0 0 0 1) substrate by mechanical grinding. As a consequence, the different crystallographic planes building up the 6H–SiC polytype are cut under continuously changing polar angles in all azimuthal directions. Through hydrogen etching, this curved surface breaks up into a whole set of surfaces vicinal to the initial 6H(0 0 0 1) orientation. The local structural reorganisation after hydrogen etching has been studied by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Two types of local bond environments are present at the step edges leading to a strong anisotropy in the surface etching with hydrogen. As a result, the distribution of the terrace width and the step heights varies with the azimuthal angle and reflects the sixfold symmetry of the bulk crystal. For most azimuthal directions, an alternation of large and small terraces, separated by steps of 0.75 nm heights (height of half the 6H polytype, three bilayers) is observed and only for well defined azimuthal directions, equally spaced terraces separated by steps of 1.5 nm height (one unit cell of 6H–SiC, six bilayers) are found. In addition, the polar variations have been studied by taking various line-scans along the concave-shaped surface with AFM. It seems that for polar angles above 3°, step bunching of several SiC steps occurs whereas below 3° the bimodal terrace width distribution is observed.     

Depth dependence of photoluminescence and chemical bonding in porous silicon

Porous silicon (PS) is studied by stepwise peeling of the surface layer to clarify the non-uniformity in the photoluminescence (PL) and correlate it with the in-depth chemical bonding and structure of the 30 μm thick layer. The PL intensity grows by an order of magnitude after the peeling off of the first 10 μm and decreases five times in the next 5 μm while the peak maximum position shifts from 730 to 800 nm. X-ray photoelectron spectroscopy (XPS) measurements show that Si–Si and Si–O bonds are present both on the surface and below, and the preferential oxidation state of silicon changes from 3+ and 4+ on the surface to 1+ and 2+ below 10 μm. Using Raman spectroscopy silicon nanocrystals are shown to exist. Their mean size can be estimated at about 3 nm. These results show that the strongest PL comes from a region in the PS layer where silicon nanocrystallites are surrounded by oxides with a low level of oxidation and not from the strongly oxidized surface layer.     

Enhanced transient reactivity of an O-sputtered Au(1 1 1) surface

The interaction of SO₂ with oxygen-sputtered Au(1 1 1) (θ_oxygen  0.35 ML) was studied by monitoring the oxygen and sulfur coverages as a function of SO₂ exposure. The morphology of the sputtered Au is relatively smooth on a long length scale, but rough on a finer scale with islands averaging 15 nm. The rough surface is not stable to scanning with the STM. Two reaction regimes were observed: oxygen depletion followed by sulfur deposition. An enhanced, transient sulfur deposition rate is observed at the oxygen depletion point. This effect is specifically pronounced if the Au surface is continuously exposed to SO₂. The enhanced reactivity towards S deposition seems to be linked to the presence of highly reactive, under-coordinated Au atoms. Adsorbed oxygen appears to stabilize, but also to block these sites. In absence of the stabilization effect of adsorbed oxygen, i.e. at the oxygen depletion point, the enhanced reactivity decays on a timescale of a few minutes. These observations shed a new light on the catalytic reactivity of highly dispersed gold nanoparticles.     

Synthesis and physico-chemical characteristics of nanosized particles produced by laser ablation of a nickel target in water

Ablation of Ni targets in water by laser impact (532 nm, 40 mJ/pulse, 10 Hz and 8 ns duration) focused on massive samples (2 mm diameter) generates colloids with fine nanoparticles. The amount of metal released in the solution (measured by mass loss of the target or ICP) was found to increase first linearly with time, but slower after 8 min of impact. The size distribution of the nanoparticles thus produced was measured (by TEM) to be in the range 3–5.3 nm in diameter, with a tendency for the size to be smaller for larger number of laser shots. Actually, nickel oxide nanoparticles were produced, rather than nickel nanoparticles as it was shown by HRTEM. XPS photoemission measurements evidenced the presence of nickel oxide species on the crater of the nickel sample surface after laser ablation.     

Two-dimensional nanopatterning by PDMS relief structures of polymeric colloidal crystals

A new constructive method of fabricating a nanoparticle self-assembly on the patterned surface of a poly(dimethylsiloxane) (PDMS) relief nanostructure was demonstrated. Patterned PDMS templates with close-packed microwells were fabricated by molding against a self-assembled monolayer of polystyrene spheres. Alkanethiol-functionalized gold nanoparticles with an average particle size of 2.5 nm were selectively deposited onto a hydrophobic self-assembled monolayer printed on the substrate by the micro-contact printing (μCP) of the prepared PDMS microwell, in which the patterned gold nanoparticles consisted of close-packed hexagons with an average diameter of 370 nm. In addition, two-dimensional colloidal crystals derived from PMMA microspheres with a diameter of 380 nm and a negative surface charge were successfully formed on the hemispherical microwells by electrostatic force using positively charged PAH-coated PDMS as a template to produce multidimensional nanostructures.     

Surface resistance measurements at the metal/electrolyte interface of Ag(100) and Ag(111) thin film electrodes

The conductivity of thin film metal electrodes with a thickness of the order of the mean free path of the conduction electrons (50 nm at 300 K) is sensitive to several processes on the metal surface (e.g. adsorption and desorption of ions). We developed epitaxially grown Ag(100)/MgO(100) and Ag(111)/TiO₂(110) electrodes of 20 nm thickness. The change in the surface resistance of Ag(100) thin film electrodes during adsorption of the halide ions Cl⁻, Br⁻ and I⁻ shows the different strengths of specific adsorption. We investigated the phase transition of thiocyanate (SCN⁻) on Ag(100) electrodes by combining the surface resistance method with voltammetric, capacitance and ex-situ XPS measurements. The influence of adsorbed uracil on the resistance of Ag(100) films was demonstrated. The surface resistance is very sensitive to small concentrations of metal cations (e.g. Tl⁺). The surface resistance of Ag(100) and Ag(111) thin film electrodes shows the typical difference in the stripping potential of Tl⁺ of about 100 mV.     

Using diffractive optical element and Zygo interferometer to test large-aperture convex surface

A valid method for measuring the large-aperture convex surface by using a curved diffractive optical element (DOE) and a Zygo interferometer is demonstrated experimentally. In this method, the direct use of source and high-resolution CCD camera of Zygo interferometer represents a major advance in the areas of adjustment. The DOE, fabricated by combining laser direct writing and lithography, results in higher accuracy, efficiency and lower cost for testing aspheric compared with other types of DOE employed. We have fabricated one optical test system and measured a 110-mm-diameter convex surface of errors 44.3 nm rms and 311 nm P–V.