Particle-in-cell mode beam dynamics simulation of the low energy beam transport for the SSC-linac injector

A new SSC-linac system (injector into separated sector cyclotron) is being designed in the HIRFL (heavy ion research facility of Lanzhou). As part of SSC-Linac, the LEBT (low energy beam transport) consists of seven solenoids, four quadrupoles, a bending magnet and an extra multi-harmonic buncher. The total length of this segment is about 7 meters. The beam dynamics in this LEBT has been studied using three-dimensional PIC (particle-in-cell) code BEAMPATH. The simulation results show that the continuous beam from the ion source is first well analyzed by a charge-to-mass selection system, and the beam of the selected charge-to-mass ratio is then efficiently pre-bunched by a multi-harmonic buncher and optimally matched into the RFQ (radio frequency quadrupole) for further acceleration. The principles and effects of the solenoid collimation channel are discussed, and it could limit the beam emittance by changing the aperture size.     

Design of the low energy beam transport line for the China spallation neutron source

The design of the China Spallation Neutron Source (CSNS) low-energy beam transport (LEBT) line, which locates between the ion source and the radio-frequency quadrupole (RFQ), has been completed with the TRACE3D code. The design aims at perfect matching, primary chopping, a small emittance growth and sufficient space for beam diagnostics. The line consists of three solenoids, three vacuum chambers, two steering magnets and a pre-chopper. The total length of LEBT is about 1.74 m. This LEBT is designed to transfer 20 mA of H-pulsed beam from the ion source to the RFQ. An induction cavity is adopted as the pre-chopper.The electrostatic octupole steerer is discussed as a candidate. A four-quadrant aperture for beam scraping and beam position monitoring is designed.     

用于强流中子发生器的低能束流传输线的设计模拟

兰州大学设计研发的ZF-400强流中子发生器设计D-T中子产额6×1012 n/s,主要由ECR离子源、低能束流传输线（LEBT）、加速管、旋转靶等部分组成。LEBT负责将从离子源引出的束流进行分析聚焦并注入到加速管中。LEBT对束流的聚焦及分析的好坏程度决定了加速管中束流的损失程度、中子的产额以及靶的寿命。本工作就该强流中子发生器所需的低能传输线进行了设计。使用螺线管、分析磁铁和四极透镜组合的方案。利用TRACK软件对此方案进行模拟,得到符合要求的束流线及元件的参数。用TraceWin进行了验证模拟,验证结果符合要求。另外,通过软件模拟确定了杂质离子损失的位置,据此设计了束流管道冷却方案。通过模拟发现,这种透镜的组合方式可以让整个LEBT以较低的功率获得低损失、高纯度的打靶束流。The ZF-400 Intense Neutron Generator, which is designed by Lanzhou University with an expected neutron yield of 6×1012 n/s, is consist of ECR ion source, low energy beam transport (LEBT) line, accelerating tube and rotating target. The beam extracted from ECR source is analyzed and focused through LEBT, then, the beam is introduced into the accelerating tube. The focus and analysis ability of LEBT is very important for the beam loss, neutron yield and target's life. A LEBT line for intense neutron generator is designed in this paper, the project consisted of a solenoid, a bend magnet and three quadrupole lens. The qualified LEBT and its parameters have been got through the simulation with TRACK code. Then TraceWin program was employed to check this simulation and the result satisfied our requirement. Besides, the loss position of impurity ions was known through the simulation, and a project of beam line's cooling system was designed according to this result. Through the simulation, we find the optimal lens combination plan which can obtain lower beam loss and higher beam purity at low running power of LEBT.     

一种用于C-ADS低能束流传输线束流强度控制的新型可调限束光阑

为了实现超导直线加速器束流强度的连续可调,并满足加速器在线稳定可靠运行,针对我国加速器驱动次临界系统(C-ADS)低能束流传输线(LEBT)的束流强度调控,提出了一种新型的可调限束光阑。可调限束光阑采用两个相对旋转的镜像对称转芯,转芯的孔径在某一范围内可以实现连续变化,以刮除不需要的外部粒子,提高束流品质,降低束损,最重要的是可实现束流强度的在线连续可调,并满足圆形束的要求。仿真和试验结果表明,在0~10 mA范围内,可以有效地卡掉不需要的外部粒子束流,并实现束流强度的在线连续调节。该装置为质子直线加速器提供了一种方便的束流调试方法,能够满足ADS直线加速器稳定可靠的在线运行。     

带有质量分析系统的强流质子束低能传输线研究

强流质子源与低能传输线（LEBT）是作为CIADS注入器的超导强流质子直线加速器的关键前端系统。目前LEBT采用双螺线管匹配结构设计,并安装有限制锥,但仍然不能避免少量H₂+和H₃+进入后端加速装置,这对直线加速器长期运行稳定性与可靠性会产生一定影响。为此,在LEBT加入分析磁铁对混合束（H+,H+2,H₃+）进行分离再注入后端加速器腔体,将是一个有效的方案。本研究对经过带有30度分析磁铁的LEBT的强流质子束的束流品质进行了模拟与实验测量。结果表明,分析磁铁高阶磁场的影响使经过分析磁铁的强流质子束束流品质变差,并且该影响随着束流包络的增大而增大。这些结果为CIADS注入器的低能传输线设计提供了参考依据。High current proton source and the low energy beam transport(LEBT) are the key front-end systems for CIADS injector:high current proton linac accelerator. CIADS injector's LEBT adopts double solenoid matching structure, using a limit cone which can partially avoid H₂+ and H₃+ which injecting into the back-end linac accelerator may impact the long-term stability and reliability of the whole system. It will be an effective method to separate the hybrid ions (H+, H₂+, H₃+) by adding a dipole magnet at LEBT. In this article, we simulated and mesasured the high current proton beam quality behind the LEBT with a 30 degree dipole. The results show that the the proton beam quality is significantly effected by high-order magnetic fields of the dipole magnet, and the effect increases with the increase of the beam envelope. The achieved result is useful for the LEBT design of CIADS injector.     

PIC mode simulation of solenoid collimation channel

A new SSC(Separated Sector Cyclotron)-Linac is being designed to serve as an injector for the SSC at the HIRFL(Heavy Ion Research Facility Lanzhou).The beam intensity at the LEBT(Low Energy Beam Transport)for the heavy ions after the selection is typically low and the space charge effects are inconspicuous.The space charge effects become obvious when the beam current increases to a few hundred microamperes.The emittance growth deriving from the space charge effects may be particularly troublesome for the following linac and cyclotron.An optical system containing three solenoids has been designed for the LEBT to limit the beam emittance and to avoid the unnecessary beam loss in the cyclotron,as well as for the purpose of immunizing the LEBT emittance growth due to the space charge effects.The results of the PIC(Particle-In-Cell)mode simulation illustrate that this channel could limit the beam emittance growth and increase the beam brightness.     

Design of magnet and control of the beam emittance for Penning H- ion source

The design requirement and principle of the deflection magnet for Magnetron and Penning H- ion source are discussed.It is proved that there exists a maximum emittance for the beam that may be transformed by the magnet into a state with equal Twiss parameters of αr=αy and βr =βy,which is the requisite condition to get a minimum emittance at the entrance of RFQ after transporting by a LEBT with solenoids.For this maximum emittance,the corresponding magnetic field gradient index is 1.     

Matching by solenoids in space charge dominated LEBTs

The betatron matching of a rotationally asymmetric beam in space charge dominated low-energy beam transports (LEBTs) where solenoids are used for the transverse matching has been studied.For better understanding, the coupling elements of a beam matrix are interpreted in special forms that are products of a term defined by the Larmor rotation angle and another by the difference between the beam matrix elements in the two transverse planes.The coupling form originally derived from the rotationally symmetric field in solenoids still holds when taking into account the rotationally asymmetric space charge forces that are due to the unequal emittance in the two transverse planes.It is shown in this paper that when an LEBT mainly comprising solenoids transports a beam having unequal emittance in the two transverse planes and the linear space charge force is taken into account, the initial Twiss parameters can be modified to obtain the minimum and equal emittance at the LEBT exit.The TRACE3D calculations also prove the principle.However, when quadrupoles that are also rotationally asymmetric are involved in between solenoids, the coupling between the two transverse planes becomes more complicated and the emittance increase is usually unavoidable.A matching example using the CSNS (China Spallation Neutron Source) LEBT conditions is also presented.     

Study on the pre-chopper in CSNS LEBT

Physical designing of the pre-chopper in CSNS LEBT is carried out,which includes the deflecting voltage,the length and the width of the deflecting plates,and the gap between the deflecting plates.The most outstanding feature of the design is that both the gap and the width vary with the beam envelope size.So both the requried deflecting voltage and the loaded capacitance are lowered.In order to avoid destruction of the space charge neutralization by the pre-chopper in the whole LEBT,an electron-trapping electrode is arranged to confine the electrostatic field of the pre-chopper to the local area.To examine the reliability of the pre-chopping design in CSNS LEBT,a similar pre-chopping design in ADS RFQ LEBT is set up and an experiment on the pre-chopper is prepared.3-dimensional simulations are carried out to determine the loaded capacitance and the applied voltage of the electron-trapping electrode.     

用于1MeV 分离作用RFQ加速器改造的ECR氧离子源及LEBT系统的研制

An ECR O~ ion source and LEBT system have been developed for the upgrade of 1MeV Integral Split Ring RFQ at Peking University.To satisfy the requirement of RFQ,a more than 10mA oxygen beam has been extracted at 22kV through a 5mm diameter aperture.Its normalized root-mean-square emmitance is less than 0.1π·mm·mrad,which is required by RFQ accelerator.The LEBT matching section is redesigned upon the bench test results.The preliminary results will be presented in this paper.     

加速器驱动次临界系统注入器离子源控制系统

强流质子源及低能传输线是加速器驱动次临界系统(ADS)项目注入器的重要组成部分,为了保证其工作效率设计了一种基于实验物理及工业控制系统(EPICS)架构的远程控制系统。根据被控设备硬件接口的特点及控制需求分别采用可编程控制器(PLC)和串口服务器等作为控制部件,在主控机中使用LabVIEW编程实现了对系统内所有设备的监控,并借助于DSC模块把设备状态和参数等以过程变量的形式进行网络发布。设计的控制系统具有结构简单、工作可靠的特点,已经在系统调试中发挥了重要作用。     

A design study on the CSNS LEBT pre-chopper

The China Spallation Neutron Source (CSNS) front end incorporates a pre-chopper in the Low Energy Beam Transport line (LEBT) that will remove a 530 ns section of beam at approximately 1 MHz rate, which is the RF frequency of the ring at injection. It’s one of the most critical devices for properly controlling the injecting beam loss. Physical designing of the pre-chopper is carried out, and the RFQ itself is used as the beam dump of the chopper system. In order to examine the reliability of the pre-chopper design, the beam study of a similar chopper system is successfully performed. The results of physical design and experiments are presented.

     

一台2.45GHz强流中子源

A 2.45GHz microwave-driven ion source is being used to provide 40mA of deuterium ion beam (peak current) for an RFQ accelerator as part of a neutron source system.We have also designed a 60kV electrostatic LEBT using computer simulations.In our experiment,we measured the hydrogen and deuterium ion beam currents as functions of discharge power,gas flow,and magnetic field strength.The required beam current was obtained using leas than 700W of net microwave power with a gas flow of less than 1.5sccm.From the rise time data,it was determined that in order to obtain a high percentage of atomic ions in the beam, the beam extraction should start after 1ms of switching on the microwave power.At steady state,the proton fraction was above 90%.     

低能强流质子束空间电荷补偿度研究(英文)

对于低能强流离子束来说,空间电荷效应的存在将导致束流发散、发射度增加等一系列问题,从而降低束流品质。幸运的是,当束流由离子源引出通过低能传输线时会与其中的剩余气体发生电离反应,产生二次电子与二次离子;二次电子在束流自身产生的电场作用下,在束流中积累并中和部分空间电荷,达到抑制空间电荷效应的效果。为了测量空间电荷中和程度,中国科学院近代物理研究所研制了一台三栅网式能量分析仪用以测量电离过程中产生的二次离子能量来间接计算空间电荷中和度。实验结果表明,对于40 keV, 18.5 mA的质子束,真空度为1.510*3 Pa 时得到最佳补偿度;真空度一定的情况下,空间电荷补偿度随束流流强增加而变大。For high-intensity low-energy ion beams, space charge effect is a main cause of beam divergence  and emittance growth. Fortunately, residual gas molecules in the drift space tend to be ionized and neutralize the beam space charge spontaneously. The level of Space Charge Neutralization (SCN)is measured through the detection of created secondary ion energy distribution in the beam region. A so-called non-interceptive Three-grid Energy Analyzer (TEA) has been designed and manufactured at Institute of Modern Physics, Chinese Academy of Sciences (IMP). This paper will present the detailsof the TEA detector and the application to diagnose proton beam SCN level in the Low Energy Beam Transport (LEBT) line. As a preliminary result, for an 18.5 mA proton beam a best compensating point appears at the vacuum pressure of 1.510*3 Pa. And the neutralization level is advanced with thegrowth of beam current in a constant vacuum pressure.     

LAPECR2离子源在320kV高压平台上的试运行

The high charge state all permanent Electron Cyclotron Resonance Ion Source(ECRIS)LAPECR2 (Lanzhou All Permanent magnet ECR ion source No.2)has been successfully put on the 320kV HV platform at IMP and also has been connected with the successive LEBT system.This source is the largest and heaviest all permanent magnet ECRIS in the world.The maximum mirror field is 1.28T(without iron plug)and the effective plasma chamber volume is as large as (?)67mm×255mm.It was designed to be operated at 14.5GHz and aimed to produce medium charge state and high charge state gaseous and also metallic ion beams.The source has already successfully delivered some intense gaseous ion beams to successive experimental terminals.This paper will give a brief overview of the basic features of this permanent magnet ECRIS.Then commissioning results of this source on the platform,the design of the extraction system together with the successive LEBT system will be presented.     

Accelerator development in India for ADS programme

At BARC, development of a Low Energy High Intensity Proton Accelerator (LEHIPA), as front-end injector of the 1 GeV accelerator for the ADS programme, has been initiated. The major components of LEHIPA (20 MeV, 30 mA) are a 50 keV ECR ion source, a 3 MeV Radio Frequency Quadrupole (RFQ) and a 20 meV drift tube linac (DTL). The Low Energy Beam Transport (LEBT) and Medium Energy Beam Transport (MEBT) lines match the beam from the ion source to RFQ and from RFQ to DTL respectively. Design of these systems has been completed and fabrication of their prototypes has started. Physics studies of the 20–1000 MeV part of the Linac are also in progress. In this paper, the present status of this project is presented.      

Multi-Gaussian Schell-model vortex beam

Multi-Gaussian Schell-model (MGSM) beam was introduced recently (Sahin and Korotkova, 2012 [34], and Korotkova et al., 2012 [35]). In this paper, multi-Gaussian Schell-model vortex (MGSMV) beam is introduced as a natural extension of MGSM beam. The explicit expression for the cross-spectral density of a MGSMV beam propagating through a stigmatic ABCD optical system is derived and the focusing properties of a MGSMV beam are studied in detail. It is found that we can shape the focused beam profile by varying the initial beam parameters, which will be useful in material thermal processing and particle trapping.     

Analysis of beam quality for the laser beams after spectral beam combining

The beam quality of the laser beams after spectral beam combining (SBC) has been analyzed in this paper. Based on the propagation model of the spectral beam combining system, the expression for the output field of an individual beam passing through the spectral beam combining system with lens aberration has been given and the intensity distribution of the combined beam has been studied by the principle of incoherent superposition. Consequently, according to the intensity second-order moments method, the M²-factor of the combined beam has been calculated and the effect of lens aberration on the characteristics of the combined beam has been analyzed quantitatively. It can be shown that the SBC system can improve the beam quality of laser array significantly, and the M²-factor of the combined beam passing through the ideal spectral beam combining system is almost the same as that of an individual beam. For the spectral beam combining system with lens aberration, the spherical aberration has greater effect on the off-axis beam than on the on-axis beam, and the beam quality of combined beam degrades with increase in lens aberration.     

A particle-in-cell mode beam dynamics simulation of medium energy beam transport for the SSC-Linac

A new linear accelerator system, called the SSC-Linac injector, is being designed at HIRFL (the heavy ion research facility of Lanzhou). As part of the SSC-Linac, the medium energy beam transport (MEBT) consists of seven magnetic quadrupoles, a re-buncher and a diagnose box. The total length of this segment is about 1.75 m. The beam dynamics simulation in MEBT has been studied using the TRACK 3D particle-in-cell code, and the simulation result shows that the beam accelerated from the radio frequency quadrupole (RFQ) matches well with the acceptance of the following drift tube linac (DTL) in both the transverse and longitudinal phase spaces, and that most of the particles can be captured by the final sector focusing cyclotron for further acceleration. The longitudinal emittance of the RFQ and the longitudinal acceptance of the DTL was calculated in detail, and a multi-particle beam dynamics simulation from the ion source to the end of the DTL was done to verify the original design.     

Flat-top beam profile generated using a fiber-bundle prism-coupled beam shaper

In this paper, an optical beam shaping system is theoretically and experimentally investigated. The optical system design software ZEMAX is used to simulate and analyze the reported beam shaping design. By using this software ray tracing diagrams are presented with the aim of studying the direct beam propagation, total reflection rays, and the lost rays. The prism duct output beam shape and radiance profiles in both position space and angle space are also studied. For experimental investigation, a two-stage beam shaping design including a fiber-bundle and a prism duct is used. A source light is used for the fiber-bundle illumination and the photograph image of the output beam is taken by a digital camera. The fiber-bundle output beam cross section is a rectangular shape with a dimension of 25.65 mm width and 2.44 mm height. In another experiment, the prism output beam is captured by a CCD camera. The prism output beam shape depends on the prism exit face, which is a rectangle (4.15 mm × 3.55 mm) for this case. The image date of the prism output beam is converted to a response curve, which is approximately a flat-top profile. The experimental image profiles are compared with the simulated image profiles and there is a good agreement between the observed results.