ESTIMATION OF ACTIVATED ENERGY OF DESORPTION OF n-HEXANE ON ACTIVATED CARBONS BY TPD TECHNIQUE

1. INTRODUCTION In some cities of China, cancer and breath system diseases caused by the pollution of volatile organic compounds (VOCs) have been obviously increasing. The VOCs includes BTEX (benzene, toluene, ethylbenzene, and xylene), aldehydes, cresol, phenol, acetic acid, polynuclear aromatic hydrocarbons (PAHs), which have long-term human health implications. Emission of the VOCs has threatened the health of people seriously [1,2]. The pollution of the VOCs mostly hails from…     

ESTIMATION OF ACTIVATED ENERGY OF DESORPTION OF n-HEXANE ON ACTIVATED CARBONS BY TPD TECHNIQUE

In this paper, six kinds of activated carbons such as Ag+-activated carbon, Cu2+-activated carbon, Fe3+- activated carbon, activated carbon, Ba2+- activated carbon and Ca2+-activated carbon were prepared. The model for estimating activated energy of desorption was established. Temperature-programmed desorption (TPD) experiments were conducted to measure the TPD curves of n-hexanol and then estimate the activation energy for desorption of n-hexanol on the activated carbons. Results showed that the activation energy for the desorption of n-hexanol on the Ag+- activated carbon, the Cu2+- activated carbon and the Fe3+- activated carbon were higher than those of n-hexanol on the activated carbon, the Ca2+- activated carbon and the Ba2+- activated carbon.     

Characteristics of Nonafluorobutyl Methyl Ether (NFE) Adsorption onto Activated Carbon Fibers and Different-Size-Activated Carbon Particles

The characteristics of adsorption of 1,1,1,2,2,3,3,4,4-nonafluorobutyl methyl ether (NFE), a chlorofluorocarbon (CFC) replacement, onto six different activated carbon; preparations (three activated carbon fibers and three different-sized activated carbon particles) were investigated to evaluate the interaction between activated carbon surfaces and NFE. The amount of NFE adsorbed onto the three activated carbon fibers increased with increasing specific surface area and pore volume. The amount of NFE adsorbed onto the three different-sized-activated carbon particles increased with an increase in the particle diameter of the granular activated carbon. The differential heat of the NFE adsorption onto three activated carbon fibers depended on the porosity structure of the activated carbon fibers. The adsorption rate of NFE was also investigated in order to evaluate the efficiency of NFE recovery by the activated carbon surface. The Sameshima equation was used to obtain the isotherms of NFE adsorption onto the activated carbon fibers and different-sized-activated carbon particles. The rate constant k for NFE adsorption onto activated carbon fibers was larger for increased specific surface area and pore volume. The rate of NFE adsorption on activated carbons of three different particle sizes decreased with increasing particle diameter at a low initial pressure. The adsorption isotherms of NFE for the six activated carbons conformed to the Dubinin-Radushkevich equation; the constants BE(0) (the affinity between adsorbate and adsorbent) and W(0) (the adsorption capacity) were calculated. These results indicated that the interaction between the activated carbon and NFE was larger with the smaller specific surface area of the activated carbon fibers and with the smaller particle diameter of the different-sized-activated carbon particles. The degree of packing of NFE in the pores of the activated carbon fibers was greater than that in the pores of the granular activated carbons. Copyright 2000 Academic Press.     

ACTIVATION ENERGY OF DESORPTION OF DIBENZOFURAN ON ACTIVATED CARBONS

Three kinds of commercial activated carbons, such as Norit RBI, Monolith and Chemviron activated carbons, were used as adsorbents for adsorption of dibenzofiuran. The average pore size and specific surface area of these activated carbons were measured Temperature Programmed Desorption (‘TPD) experiments were conducted to measure the TPD curves of dibenzofuran on the activated carbons, and then the activation energy for desorption of dibenzofuran on the activated carbons was estimated. The results showed that the Chemviron and the Norit RB1 activated carbon maintained higher specific surface area and larger micropore pore volume in comparison with the Monolith activated carbon, and the activation energy for the desorption of dibencofuran on these two activated carbons was higher than that on the Monolith activated carbon. The smaller the pore of the activated carbon was, the higher the activated energy of dibenzofiuran desorption was.     

ACTIVATION ENERGY OF DESORPTION OF DIBENZOFURAN ON ACTIVATED CARBONS

1. INTRODUCTION With the development of municipalization in China, more and more cities are challenged by the problem of how to dispose of the dramatically increased municipal waste. Generally, most of municipal solid waste is landfilled or dumped openly in the suburbs. It causes not only land waste, but also serious environment pollution. In order to solve efficiently the environment pollution caused by municipal solid waste, incineration technique was introduced in some big cities such…     

Adsorption of urea onto granular activated alumina: A comparative study with granular activated carbon

ABSTRACT

This study investigated the ability of granular activated alumina to remove urea from wastewater through adsorption, and compared its performance with granular activated carbon. XRF, EDX, XRD, and TGA were used to investigate the adsorbents. The removal of urea as a function of pH value was studied. The point of zero charge for activated alumina was found to be 8.8, while that for activated carbon was found to be 7.1. The experimental data of the adsorption process were explored by fitting to different kinetic models to determine the adsorption kinetics and mechanisms. Then, the equilibrium data were examined by fitting to various two-parameter and three-parameter isotherm models. Results showed that the removal efficiency increased with the increasing pH value. The maximum removal efficiencies were 24% and 31% for granular activated alumina and granular activated carbon, respectively, at pH?=?9.0. Kinetic studies showed that adsorption of urea onto both activated alumina and activated carbon can be expressed by pseudo second order kinetics. Equilibrium studies showed that the adsorption isotherms could be expressed by the Redlich-Peterson isotherm and Temkin isotherm for activated alumina and activated carbon, respectively. Adsorbents were investigated using FTIR and SEM, and results showed the occurrence of adsorption.     

Adsorption properties of activated carbon from waste newspaper prepared by chemical and physical activation

Adsorption properties of activated carbons prepared from waste newspaper by chemical and physical activation were investigated using water vapor, ammonia, methane, and methylene blue (MB) as adsorbents. The water vapor adsorption isotherms show type V behavior and the maximum vapor adsorption of the chemically and physically activated products is about 1050 and 450 ml/g, respectively. The higher water vapor adsorption of the chemically activated products is attributed to the higher specific surface area (S(BET)) and greater hydrophilic activity (arising from the surface oxygen-containing functional groups) than in the physically activated products. The adsorption of ammonia and methane was measured by temperature-programmed desorption (TPD). NH(3) adsorption is found to be higher in the chemically activated product than in the physically activated product while methane adsorption is slightly higher in the physically activated products even though these have lower S(BET) values. In the MB adsorption, the chemically activated products show higher adsorption (390 mg/g) than the physically activated product. These results are suggested to be related to the surface characteristics.     

ESTIMATION OF ACTIVATED ENERGY OF DESORPTION OF n—HEXANE ON ACTIVATED CARBONS BY PTD TECHNIQUE

In this paper,six kinds of activated carbons such as Ag^+-activated carbon,Cu^2+activated carbon,Fe^3+-activated carbon,activated carbon,Ba^2+-activated carbon and Ca^2+activated carbon were prepared.The model for estimating activated energy of desorption was established.Temperature-programmed desorption(TPD)experiments were conducted to measure the TPD curves of n-hexanol and then estimate the activation energy for desorption of n-hexanol on the activated carbons.Results showed that the activation energy for the desorption of n-hexanol on the Ag^+-activated carbon,the Cu^2+-activated carbon and the Fe^3+-activated carbon were higher than those of n-hexanol on the activated carbon,the Ca^2+-activated carbon and the Ba^2+-activated carbon.     

高分子热活化延迟荧光材料研究进展

高分子热活化延迟荧光材料能够利用热活化的反向系间窜越过程将三线态激子转变为单线态激子而发出荧光,理论上可以实现100%的内量子效率,突破了传统高分子荧光材料内量子效率不超过25%的极限,因而代表了未来低成本高效率高分子发光材料的发展方向。 近年来,高分子热活化延迟荧光材料在分子设计方面取得了重要进展,形成了主链型、侧链型和树枝状高分子热活化延迟荧光材料等材料体系,同时其器件性能得到了大幅提升,部分材料的器件效率达到了高分子磷光材料的水平。 本文从材料和器件两个方面,围绕高分子热活化延迟荧光材料的分子结构、光物理特性和器件性能,总结和评述了国内外研究者在该领域方向的研究进展,并分析了未来发展面临的机遇和挑战。     

Kinetic and equilibrium studies of urea adsorption onto activated carbon: Adsorption mechanism

We found that activated carbon effectively removed urea from solution and that urea adsorption onto activated carbon followed a pseudo-second-order kinetic model. We classified the urea adsorption on activated carbon as physical adsorption and found that it was best described by the Halsey adsorption isotherm, suggesting that the multilayer adsorption of urea molecules on the adsorption sites of activated carbon best characterized the adsorption system. The mechanism of adsorption of urea by activated carbon involved two steps. First, an amino (–NH₂) group of urea interacted with a carbonyl (–C?O) group and a hydroxyl (?OH) group on the surface of activated carbon via dipole–dipole interactions. Next, the –C?O group of the urea molecule adsorbed to the activated carbon interacted with another –NH₂ group from a second urea molecule, leading to multilayer adsorption.     

Adsorption of toluene and toluene–water vapor mixture on almond shell based activated carbons

The aim of work is to study the adsorption of a common volatile organic compound such as toluene using activated carbons prepared by chemical activation with phosphoric acid of a lignocellulosic precursor, almond shell, under different conditions. The Impregnation ratio, temperature and time of activation were modified to obtain activated carbons with different characteristics. Regarding the characteristics of the activated carbons, the effects of porous structure and surface chemistry on the toluene adsorption capacity from toluene isotherms have been analysed. Results show that the control of properties of the activated carbons, particularly porous structure, highly dependent on the preparation conditions, plays a decisive role on the toluene adsorption capacity of the activated carbons. Concerning the experiments of toluene adsorption conducted in dynamic mode, activated carbons prepared at low temperatures of activation show higher breakthrough times than those obtained for activated carbons prepared at higher activation temperatures. The amount of toluene adsorbed in presence of water vapor in the gas stream lead to a decrease ranging from 33 to 46 % except for carbons prepared at higher temperatures activated that show only a slight decrease in the amount of toluene adsorbed. Activated carbons can be regenerated with soft heat treatment showing a slight decrease in the adsorption capacity. The high toluene adsorption capacities as well as the high breakthrough times obtained in presence of water vapor make these activated carbons suitable for commercial applications.     

Polymer-supported tetrafluorophenol: a new activated resin for chemical library synthesis

A new tetrafluorophenol activated resin that facilitates the use of 19F NMR to quantitate loading is presented. This new resin provides a useful tool for acylation, and a novel activated polymeric sulfonate ester to generate sulfonamides. This activated resin reacts with a wide scope of N-nucleophiles including primary and secondary amines, and anilines. This new activated resin methodology provides a powerful tool for pure single-compound library synthesis.     

活性炭纤维吸附脱除NO过程中NO氧化路径分析

在小型固定床吸附实验台上开展了黏胶基活性炭纤维吸附脱除NO的实验研究。采用H₂O₂溶液浸渍以及热处理方法对活性炭纤维表面进行修饰,以获得表面孔隙结构接近而含氧官能团含量不同的样品;考察样品在惰性氮气气氛、含氧气氛下吸附脱除NO的效果,以及表面含氧含氮官能团的变化规律。探讨了含氧官能团在NO催化氧化过程中的作用及含氧气氛下O₂对于NO转化为NO₂的影响,分析了活性炭纤维表面吸附的NO向NO₂的主要转化途径。结果表明,在氮气气氛下活性炭纤维表面C-O官能团对吸附态的NO起到氧化作用,吸附态NO被C-O官能团氧化生成-NO₂官能团;在含氧气氛下活性炭纤维吸附NO后表面出现-NO₂、-NO₃官能团,通过长时间实验测定三种样品在含氧气氛下对NO吸附的效果,发现三种样品稳定时催化氧化效果一致,表明含氧官能团对初始NO的物理吸附影响较大,而对整个吸附过程影响较小。吸附在活性炭纤维表面上的NO与环境气氛中的游离态O₂发生氧化反应是NO转变为NO₂的主要途径。     

Pore structure and adsorption performance of the KOH-activated carbons prepared from corncob

Carbonaceous adsorbents with controllable surface area were chemically activated with KOH at 780 degrees C from chars that were carbonized from corncobs at 450 degrees C. The pore properties, including BET surface area, pore volume, pore size distribution, and mean pore diameter of these activated carbons, were characterized by the t-plot method based on N(2) adsorption isotherms. Two groups are classified according to the types of adsorption/desorption isotherms. Group I corncob-derived activated carbons, with KOH/char ratios from 0.5 to 2, exhibited BET surface area ranging from 841 to 1221 m(2)/g. Group II corncob-derived activated carbons, with KOH/char rations from 3 to 6, showed high BET surface areas, from 1976 to 2595 m(2)/g. From scanning electron microscopic (SEM) results, the surface morphology of honeycombed holes on corncob-derived activated carbons was significantly influenced by the KOH/char ratios. The adsorption kinetics of methylene blue, basic brown 1, acid blue 74, 2,4-dichlorophenol, 4-chlorophenol, and phenol from water at 30 degrees C were studied on the two groups of activated carbons, which were suitably described by two simplified kinetic models, pseudo-first-order and pseudo-second-order equations. The effective particle diffusivities of phenols and dyes at the corncob-derived activated carbons of group II are higher than those of ordinary activated carbons. The high-surface-area activated carbons were demonstrated to be promising adsorbents for pollution control and for other applications.     

Competitive adsorption and desorption of a bi-solute mixture: effect of activated carbon type

This study aims to clarify the effects of carbon activation type and physical form on the extent of adsorption capacity and desorption capacity of a bi-solute mixture of phenol and 2-chlorophenol (2-CP). For this purpose, two different PACs; thermally activated Norit SA4 and chemically activated Norit CA1, and their granular countertypes with similar physical characteristics, thermally activated Norit PKDA and chemically activated Norit CAgran, were used. The thermally activated carbons were better adsorbers for phenol and 2-CP compared with chemically activated carbons, but adsorption was more reversible in the latter case. 2-CP was adsorbed preferentially by each type of activated carbon, but adsorption of phenol was strongly suppressed in the presence of 2-CP. The simplified ideal adsorbed solution (SIAS) model underestimated the 2-CP loadings and overestimated the phenol loadings. However, the improved and modified forms of the SIAS model could better predict the competitive adsorption. The type of carbon activation was decisive in the application of these models. For each activated carbon type, phenol was desorbed more readily in the bi-solute case, but desorption of 2-CP was less compared with single-solute. This was attributed to higher energies of 2-CP adsorption.     

一步法制备糖蜜基活性炭及其界面吸附行为

以糖厂废弃的糖蜜为原料,Na_2CO_3为活化剂,采用一步直接化学活化法制备了糖蜜基活性炭(AC).采用X射线衍射(XRD)、扫描电子显微镜(SEM)、N_2吸附-脱附及元素分析手段对产物进行了表征,证实其为多孔的石墨化碳材料,比表面积高达1023 m~2/g.研究了糖蜜基活性炭对溶液中的重金属离子Pb(Ⅱ)的脱除性能,结果表明:糖蜜基活性炭的吸附容量高于市售活性炭(CC),且所需吸附时间和投炭量均低于市售活性炭;其吸附动力学符合准二级动力学的Langmuir吸附,为单分子层的化学吸附;吸附Pb(Ⅱ)的糖蜜基活性炭可循环再生和重复使用.     

Reduction of Iron(III) Ion by Activated Carbon Fiber

The mechanisms of adsorption of iron(II) ion, iron(III) ion, and reduced iron(III) ion onto an activated carbon fiber and the ability of carbon fibers to reduce iron(III) ion were investigated on the basis of the amounts of iron ion adsorbed. The amount of iron(II) ion adsorbed onto the activated carbon fiber increased with increasing adsorption temperature. Iron(II) ion was more easily removed by the activated carbon fiber than iron(III) ion. Iron(III) ion was adsorbed onto the activated carbon fiber after being reduced to iron(II) ion. The reduction ability of A-20 was stronger than that of A-10 because the hydrophilic groups of A-20 were larger than those of A-10. It is concluded that the activated carbon fiber has a reduction effect on iron(III) ion and that the reduction effect of the activated carbon fiber depended on the number of hydrophilic groups on the activated carbon fiber. Copyright 2000 Academic Press.     

A novel study on synthesis of egg shell based activated carbon for degradation of methylene blue via photocatalysis

Egg shell-based activated carbon was successfully synthesized by the simple chemical activation process. Orthophosphoric acid and sodium hydroxide used as an activation agent. XRD pattern reveals the hexagonal structure of activated carbon. The functional group presents in activated carbon was identified using FT-IR spectroscopy. SEM images show irregular shapes of carbon. The photocatalytic performance of investigated activated carbon by illuminating methylene blue dye under UV–Visible irradiations. Photocatalytic activity of activated carbon results maximum degradation efficiency of 83%. Adsorption efficiency have been increased with respect of time for degradation of dye. Free radicals and superoxide’s play a significant role is decolourization of methylene blue. Photocatalytic activity of activated carbon synthesized by Orthophosphoric acid results shows the high degradation efficiency when compared to NaOH.     

Study of chromium(VI) adsorption onto modified activated carbons with respect to analytical application

Two different types of modification of activated carbon, by treatment with concentrated solution of HNO₃ and outgassing treatment at high temperature, were studied in order to obtain the most effective adsorption of chromium(VI) ions from water solution. The basic parameters affecting the adsorption capacity of Cr(VI) ions on modified activated carbons were studied in details and the effect of modifications of activated carbons has been determined by studying the initial runs of adsorption isotherms. The obtained Cr(VI) adsorption isotherms were well fitted in the Freundlich equation. The reduction of Cr(VI) to Cr(III) and further ion exchange mechanism of adsorption onto oxidizing activated carbon and surface precipitation to Cr(OH)₃ in case of outgassing activated carbon were found as the main adsorption mechanisms of Cr(VI) ions onto modified activated carbons. Presence of chlorides and nitrates in studied adsorption system strongly decreased the adsorption ability of Cr(VI) onto outgassing activated carbon and mechanism of this behavior is proposed.     

Adsorption of sodium dodecylbenzenesulfonate on activated carbons: effects of solution chemistry and presence of bacteria

The objective of the present investigation was to determine the effectiveness of activated carbon in removing sodium dodecylbenzenesulfonate (SDBS) and to analyze the chemical and textural characteristics of the activated carbons that are involved in the adsorption process. Studies were also performed on the influence of operational variables (pH, ionic strength, and presence of microorganisms) and on the kinetics and interactions involved in the adsorption of this pollutant on activated carbon. The kinetics study of SDBS adsorption revealed no problems in its diffusion on any of the activated carbons studied, and Weisz-Prater coefficient (C WP) values were considerably lower than unity for all activated carbons studied. SDBS adsorption isotherms on these activated carbons showed that: (i) adsorption capacity of activated carbons was very high (260-470 mg/g) and increased with larger surface area; and (ii) dispersive interactions between SDBS and carbon surface were largely responsible for the adsorption of this pollutant. SDBS adsorption was not significantly affected by the solution pH, indicating that electrostatic adsorbent-adsorbate interactions do not play an important role in this process. The presence of electrolytes (NaCl) in the medium favors SDBS adsorption, accelerating the process and increasing adsorption capacity. Under the working conditions used, SDBS is not degraded by bacteria; however, the presence of bacteria during the process accelerates and increases SDBS adsorption on the activated carbon. Microorganism adsorption on the activated carbon surface increases its hydrophobicity, explaining the results observed.