Controlled radical polymerization of alkyl acrylates and styrene using a half-sandwich molybdenum(III) complex containing diazadiene ligands

The half-sandwich molybdenum(III) complex CpMoCl₂(ⁱPr₂-dad) (ⁱPr₂-dad=ⁱPr-NCH-CHN-ⁱPr) proved to be an effective metal catalyst for the controlled radical polymerization of methyl acrylate, butyl acrylate, and styrene. In conjunction with an alkyl iodide [R-I: CH₃CH(COOEt)I] as an initiator and in the presence or absence of Al(O-i-Pr)₃ as a co-catalyst, the molybdenum-based system gave polymers with narrow molecular weight distributions. The in situ addition of styrene to a macroinitiator of poly(methylacrylate) afforded an AB-type block copolymer.     

Synthesis and MALDI-TOF-MS of PS-PMA and PMA-PS block copolymers

The synthesis of well-defined block copolymers from styrene and methyl acrylate via ATRP is discussed in this contribution. Kinetic studies on these block copolymerizations as well as characterization studies were performed to investigate the monomer composition in the respective PS and PMA blocks. MALDI-TOF-MS was performed to clarify the exact number of repeating units of each block and the total number of units in the block copolymer. Block copolymers up to 22 kDa could be analyzed by MALDI-TOF-MS, whereby polymers with PMA as first block showed a large second distribution corresponding to PMA homopolymers. However, SEC demonstrated that only a small amount of homopolymer was present indicating that care needs to be taken with interpreting MALDI-TOF-MS data, which is a qualitative rather than a quantitative technique.     

Thiol-ended polyethylene oxide as reactive stabilizer for dispersion polymerization of styrene

 Radical dispersion polymerization of styrene in aqueous ethanol solutions was performed in the presence of a new reactive polyethylene oxide stabilizer with thiol end groups. This reactive stabilizer was compared to the more conventional poly (N-vinyl pyrrolidone). Particles size distribution, molecular weights and kinetics were investigated. Monodispersed polymer particles with diameter in the range 200–2000 nm were obtained depending on the amount of stabilizer used. In all cases, the polyethylene oxide (PEO) sequence of the dispersant was partly incorporated at the surface of the latex particles, but the grafting yield of polyethylene oxide chains was always limited and did not exceed 15%. Part of the stabilizer being unreacted or reacted with low molecular weight polystyrene remained in the continuous phase. Received: 26 September 1996 Accepted: 4 March 1997     

Synthesis of poly(vinyl acetate)-b-poly(dimethylsiloxane)-b-poly(vinyl acetate) triblock copolymers by iodine transfer polymerization

Iodine transfer polymerization of vinyl acetate in bulk, initiated by α,α′-azobisisobutyronitrile at 80 °C, has been successfully performed in the presence of an α,ω-diiodo-poly(dimethylsiloxane) macrotransfer agent. The formation of a triblock copolymer PVAc-b-PDMS-b-PVAc has been proved by ¹H NMR and size exclusion chromatography analyses. The analysis of the chain-ends has been performed using ¹H NMR. It was found that a large amount of inverse chain-ends is present at the end of the polymerization. Moreover, the formation of several other side products by degradation of the functional chain-ends has been evidenced.     

Y-shaped block copolymers of poly(ethylene glycol) and poly(N-isopropylacrylamide) synthesized by ATRP

Novel Y-shaped block copolymers of poly(ethylene glycol) and poly(N-isopropylacrylamide),PEG-b-(PNIPAM)_2,were successfully synthesized through atom transfer radical polymerization(ATRP).A difunctional macroinitiator was prepared by esterification of 2,2-dichloroacetyl chloride with poly(ethylene glycol) monomethyl ether(PEG).The copolymers were obtained via the ATRP of N-isopropylacrylamide(NIPAM) at 30℃with CuCl/Me_6TREN as a catalyst system and DMF/H_2O(v/v = 3:1) mixture as solvent.The resulting copo...     

Synthesis of hyperbranched-linear star block copolymers by atom transfer radical polymerization of styrene using hyperbranched poly(siloxysilane) (HBPS) macroinitiator

Hyperbranched-linear star block copolymers, hyperbranched poly(siloxysilane)-block-polystyrene (HBPS-b-PSt), were prepared by atom transfer radical polymerization (ATRP) of styrene in xylene, using bromoester-terminated HBPS (HBPS-Br (P3), M_n = 7500, M_w/M_n = 1.76) as a macroinitiator. The number-average molecular weights of the obtained polymers (M_n) were in the range of 21,800-60,000 and molecular weight distributions were unimodal throughout the reaction (M_w/M_n = 1.28-1.40). These polymers showed 5 wt.% decomposition temperature (T_d5) over 300 °C. The DSC thermograms of the resulting polymers indicated two glass transition temperatures (T_g). The T_g of HBPS segment shifted to higher value while the T_g of PSt segment shifted to lower value compared with those of the homopolymers. Preliminary physical characterization related to the solution viscosity of the resulting block copolymers is also reported.     

Controlled/“living” atom transfer radical polymerization of methyl methacrylate in the synthesis of triblock copolymers from a poly(oxyethylene) macroinitiator

Atom transfer radical polymerization of methyl methacrylate initiated by a poly(oxyethylene) macroinitiator by the esterification of PEG 1500 with 2-chloro propionyl chloride was synthesized. These polymerization proceeds both in bulk and solution with a quantitative initiation efficiency, leading to A-B-A triblock copolymers. The macroinitiators and their block copolymers were characterized by FT-IR, FT-NMR and GPC analyses. In bulk polymerization, the kinetic study showed that the relationship between ln[M]₀/[M] vs time was linear showing that there is a constant concentration of active species throughout the polymerization and follow the first order kinetics with respect to monomer. Moreover, the experimental molecular weight of the block copolymers increased linearly with the monomer conversion and the polydispersity index remained between 1.3 and 1.5 throughout the polymerization. No formation of homo poly(methyl methacrylate) could also be detected, and all this confirms that the bulk polymerization proceeds in a controlled/“living” manner.     

Atom transfer radical polymerization of styrene from different poly(ethylene terephthalate) surfaces: Films, fibers and fabrics

Poly(ethylene terephthalate) (PET) is a semi-crystalline thermoplastic polyester used in many fields. For a variety of applications, however, it is necessary to impart desired properties by introducing specific functional groups on the surface. A simple method for growing polymer brushes by atom transfer radical polymerization (ATRP) on PET films, fibers and fabrics was devised. The different PET surfaces were first reacted with 1,2-diaminoethane by aminolysis reaction to incorporate primary amino and alcohol functions on the surface. Then, in a second step, ATRP initiator was grafted by reaction with bromoisobutyryl bromide. The efficiency of these reactions was confirmed by using colorimetric titration and X-ray photoelectron spectroscopy (XPS). Surface-initiated ATRP was performed in bulk using styrene monomer with CuBr/PMDETA catalytic system in the presence of a sacrificial initiator (ethyl 2-bromoisobutyrate). Good control of the polymerization was obtained as attested by comparison of polystyrene molar masses obtained in solution from sacrificial initiator with those obtained from the surface after cleavage. Wetting properties were found to vary systematically depending to the type of functionalization and grafting. Evolution of surface morphology according to reaction steps was investigated using atomic force microscopy (AFM).     

酶促缩聚和原子转移自由基聚合法合成AB型两亲性嵌段共聚物

Novozyme-435催化10-羟基癸酸进行自缩聚反应得到线性聚酯, 端基分别是羟基(—OH)和羧基(—COOH), 在三乙胺催化下, 分别用α-溴代丙酰溴和三甲基氯硅烷(TMSCL)进行端基官能化生成一个单官能度的大分子引发剂, 在CuCl/2,2'-联吡啶(bpy)催化体系中, 引发甲基丙烯酸环氧丙酯(GMA)的原子转移自由基反应(ATRP), 得到聚(10-羟基癸酸酯)/聚甲基丙烯酸环氧丙酯(PHDA-b-PGMA) AB 型两亲性嵌段共聚物, 其结构及分子量(分布)通过核磁共振和凝胶渗透色谱(GPC)确证. 此AB型两亲性嵌段共聚物在水溶液中能自组装形成纳米粒子, 用原子力显微镜(AFM)观察粒子的形状和大小.     

Fabrication of zinc oxide/poly(styrene) grafted nanocomposite latex and its dispersion

Zinc oxide nanoparticles, with an average size of about 40 nm, were encapsulated by polystyrene using in situ emulsion polymerization in the presence of 3-methacryloxypropyltrimethoxysilane (MPTMS) as a coupling agent and polyoxyethylene nonylphenyl ether (OP-10) as a surfactant. Polymerization mechanism of nanocomposite latex was discussed. Transmission electron microscopy (TEM) proved the presence of ZnO nanoparticle appeared to be monodisperse in nanosize in polymer composite particles. ZnO/PS nanocomposites were characterized by Fourier transform infrared spectra (FT-IR), X-ray photoelectron spectroscopy (XPS), thermo-gravimetric analysis (TGA) and differential scanning calorimetry (DSC). The results of FT-IR and XPS revealed that the surface of ZnO particle was successfully grafted by PS through the link of the coupling agent between ZnO and polymer. TGA and DSC results indicated an enhancement of thermal stability of composite materials compared with the pure polymer. SEM (scanning electron microscope) images showed a perfect dispersion of the ZnO particles in latex film. In addition, UV-visible absorption measurements demonstrated that the ZnO/PS composite coatings display a perfect performance of absorbing UV light.     

Synthesis of Poly(styrene sulfonyl chloride) via reversible addition-fragmentation chain transfer polymerization and characterization thereof for membrane applications

Reversible addition-fragmentation chain transfer (RAFT) polymerization has been examined for the synthesis of poly (styrene sulfonyl chloride) (PSSC) of high molecular weight and narrow polydispersity index (PDI). PSSC, contains reactive sulfonyl chloride that can allow use of organic solvent for membrane casting, and chemical modification through reactive sulfonyl groups. For PSSC preparation, end-capped styrene i.e. styrene sulfonyl chloride (SSC) is used as a monomer, which is derived from sodium 4-vinylbenzenesulfonate by chlorination with thionyl chloride. Fourier transform infrared spectroscopy, Raman spectroscopy and Proton nuclear magnetic resonance spectroscopy, have been successfully used to confirm the polymer architecture. End-group of PSSC containing RAFT agent (Cyanomethyl N-methyl-N-phenylcarbamodithioate), is also confirmed by fragmentation analysis using Gas chromatography-mass spectroscopy. Evaluation of PSSC by X-ray diffraction and differential scanning calorimetry showed that resulting polymer is predominantly amorphous in nature and has a glass transition temperature of 119 ​°C. Gel permeation chromatography data reveals formation of high molecular weight (84 ​kDa) PSSC with and low PDI (1.4). Moreover, PSSC can be converted to polyelectrolyte and can be crosslinked by interfacial polymerization concept; hence, it would have considerable prospective for membrane preparation for fuel cell and water purification.     

Direct synthesis of amphiphilic block copolymers, consisting of poly(methyl methacrylate) and poly(sodium styrene sulfonate) blocks through atom transfer radical polymerization

Amphiphilic block copolymers of methyl methacrylate (MMA) and sodium styrene sulfonate (SSNa) were successfully synthesized via direct atom transfer radical polymerization (ATRP) of SSNa. First, poly(sodium styrene sulfonate) (PSSNa) or poly(methyl methacrylate) (PMMA) macroinitiators were prepared using proper ATRP systems for each case. In some cases, functional initiators, which allow further reactions, were used. The macroinitiators were characterized and further used to synthesize PSSNa/PMMA block copolymers, by using proper solvent combinations, such as N,N-dimethylformamide/water or methanol/water at appropriate volume ratios, in order to ensure solubility of the synthesized amphiphilic copolymers. The molecular weight of the copolymers was determined by gel permeation chromatography, using water as eluent. By using a combination of analytical techniques like ¹H NMR, FTIR and thermogravimetry, the chemical structure and the actual copolymer composition were determined. Since, the block copolymers were soluble in water, forming hydrophilic/hydrophobic domains in aqueous solution, their micellization behavior was further studied by pyrene fluorescence probing.     

原子转移自由基聚合制备聚(甲基丙烯酸甲酯-b-苯乙烯)时单体聚合顺序对嵌段效率的影响

采用原子转移自由基聚合研究了聚（ 甲基丙烯酸甲酯 ｂ 苯乙烯） 嵌段共聚物的合成,实验结果表明,当先进行甲基丙烯酸甲酯的聚合,然后再进行苯乙烯的聚合时,得到了完全的嵌段共聚物;反之,如果改变单体的聚合顺序,则嵌段效率很低．用聚合物末端Ｃ—Ｘ（Ｘ＝ Ｃｌ,Ｂｒ） 键的断裂能对实验结果进行了解释．     

Synthesis of styrene/methyl methacrylate copolymers by atom transfer radical polymerization: 2D NMR investigations

Copolymers of styrene and methyl methacrylate were synthesized by atom transfer radical polymerization using methyl 2‐bromopropionate as initiator and CuBr/N,N,N′,N′,N″‐pentamethyldiethylenetriamine as catalyst. Molecular weight distributions were determined by gel permeation chromatography. The composition of the copolymer was determined by ¹H NMR. The comonomer reactivity ratios, determined by both Kelen–Tudos and nonlinear error‐in‐variables methods, were r_S = 0.64 ± 0.08, r_M = 0.63 ± 0.08 and r_S = 0.66, r_M = 0.65, respectively. The α‐methyl and carbonyl carbon resonances were found to be compositionally and configurationally sensitive. Complete spectral assignments of the ¹H and ¹³C NMR spectra of the copolymers were done by distortionless enhancement by polarization transfer and two‐dimensional NMR techniques such as heteronuclear single quantum coherence and heteronuclear multiple quantum coherence. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2076–2085, 2006     

Synthesis of bis-allyloxy functionalized polystyrene and poly (methyl methacrylate) macromonomers using a new ATRP initiator

A new bis-allyloxy functionalized ATRP initiator, viz, 4,4-bis (4-(allyloxy) phenyl) pentyl-2-bromo-2-methylpropanoate was synthesized starting from commercially available 4,4-bis (4-hydroxyphenyl) pentanoic acid. Atom transfer radical polymerization of styrene in bulk and that of methyl methacrylate in anisole using CuBr/N,N,N′,N′,N″-pentamethyldiethylenetriamine system was carried out. The kinetic study of styrene polymerization showed controlled polymerization behavior. Bis-allyloxy functionalized well-defined polystyrene (M_n^GPC: 13,600–28,250, PDI: 1.07–1.09) and poly (methyl methacrylate) (M_n^GPC: 10,100–18,450, PDI: 1.23–1.34) macromonomers were obtained. The presence of allyloxy functionality was confirmed by ¹H NMR spectroscopy. The reactivity of allyloxy functionality was demonstrated by carrying out organic reactions such as addition of bromine and hydrosilylation on polystyrene macromonomer. Polystyrene macromonomer with bis-allyloxy functionality was transformed into bis-epoxy functionalized polystyrene macromonomer using 3-chloroperoxybenzoic acid.     

Tethering hydrophilic polymer brushes onto PPESK membranes via surface-initiated atom transfer radical polymerization

Surface-initiated atom transfer radical polymerization (ATRP) was used to graft hydrophilic comb-like poly((poly(ethylene glycol) methyl ether methacrylate), or P(PEGMA), brushes from chloromethylated poly(phthalazinone ether sulfone ketone) (CMPPESK) membrane surfaces. Prior to ATRP, chloromethylation of PPESK was beforehand performed and the obtained CMPPESK was prepared into porous membranes by phase inversion process. It was demonstrated that the benzyl chloride groups on the CMPPESK membrane surface afforded effective macroinitiators to graft the well-defined polymer brushes. Attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS) confirmed the grafting of P(PEGMA) chains. Water contact angle measurements indicated that the introduction of P(PEGMA) graft chains promoted remarkably the surface hydrophilicity of PPESK membranes. The effects of P(PEGMA) immobilization on membrane morphology, permeability and fouling resistance were investigated. It was found that the comb-like P(PEGMA) grafts brought smaller pore diameters and higher solute rejections to PPESK membranes. The results of dynamic anti-fouling experiments showed the anti-fouling ability of the membranes was significantly improved after the grafting of P(PEGMA) brushes.     

Stepwise dansyl grafting on the kaolinite interlayer surface

A block copolymer (PS-b-poly(l-Glu)) composed of polystyrene and poly(l-glutamic acid) was used as a stabilizer for dispersion polymerization of styrene. When dispersion polymerization of styrene was conducted at 70 °C in 80% dimethylformamide-water with 0.5 wt% PS-b-poly(l-Glu), spherical polystyrene particles with D_n = 0.72 μm and narrow size distribution were obtained. Whereas AIBN concentration did not have any effects on particle size, molecular weight of the polystyrene particles was strongly dependent on the initiator concentration. As concentration of the PS-b-poly(l-Glu) increased from 0.2 to 1.0 wt%, particle size decreased from D_n = 0.91 to 0.69 μm with keeping surface area occupied by one poly(l-glutamic acid) chain about S = 50 nm². On the other hand, an increase in initial concentration of styrene from 2 to 20 wt% caused an increase in particle size from D_n = 0.48 to 1.36 μm and a decrease in surface area per poly(l-glutamic acid) block from S = 91 to 45 nm². Colloidal stability of the polystyrene particles in aqueous solution was responsive to pH due to the surface-grafted poly(l-glutamic acid). For dispersion polymerization of styrene, the PS-b-poly(l-Glu) functions as both a stabilizer and a surface modifier.     

“Living” radical polymerization of styrene catalyzed by cyclometalated ruthenium(II) complexes bearing nonlabile ligands

Cationic substitutionally inert cyclometalated ruthenium (II) and osmium (II) complexes, ([Mt(o‐C₆H₄‐2‐py)(LL)₂]PF₆), where LL‐1,10‐phenanthroline (phen) or 2,2′‐bipyridine (bipy), were used for radical polymerization of styrene. Gradual modification of the complexes within the series allowed comparison of the catalytic activity and the redox properties. There was no correlation between the reducing powers of the complexes and their catalytic activities. The osmium compound of the lowest reduction potential was not active. All the ruthenium complexes catalyzed the polymerization of styrene in a controlled manner; but the level of control and the catalytic activity were different under the same polymerization conditions. [Ru(o‐C₆H₄‐2‐py)(phen)₂]PF₆ demonstrated the best catalytic performance though its redox potential was the highest. It catalyzed the “living” polymerization with a reasonable rate at a catalyst‐to‐initiator ratio of 0.1. 1 equiv. of Al(OiPr)₃ accelerated the polymerization and improved the control, but higher amount of Al(OiPr)₃ did not speed up the polymerization and moved the process into the uncontrollable regime. Under the most optimal conditions, the controlled polymerization occurs fast without any additive and the catalyst degradation. Added free ligands inhibited the polymerization suggesting that the catalytically active ruthenium intermediates are generated via the reversible dechelation of bidentate phen or bipy ligands. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3814–3828, 2009     

ATRP技术制备末端和中间功能化的温度敏感性聚N,N-二乙基丙烯酰胺

合成了2种含有二硫吡啶结构的原子转移自由基聚合(ATRP)引发剂,ATRP引发剂结构采用核磁共振氢谱(1H-NMR)表征.结果显示,二硫吡啶结构被成功引入引发剂结构末端或链中间.利用2种ATRP引发剂分别制备了链末端功能化和链中间功能化的聚N,N-二乙基丙烯酰胺(pDEAAm).采用1H-NMR和凝胶渗透色谱(GPC)对聚合物结构和分子量进行了表征.1H-NMR结果显示,二硫吡啶基团被引入聚合物链末端或中间.GPC结果表明,末端功能化和中间功能化的聚N,N-二乙基丙烯酰胺(pDEAAm)分子量分布指数分别为1.21和1.23,实现了分子量的可控聚合.并且,具有2个引发位点的引发剂引发单体得到聚合物的分子量较大.采用紫外-可见分光光度法研究了聚合物在溶液中的温度响应性.紫外-可见分光光度法结果说明,pDEAAm溶液在28°C发生相分离,在溶液中表现出温度响应性,且最低临界溶解温度(LCST)为28°C.在末端功能化和中间功能化温敏型pDEAAm可用于嵌段共聚物的合成以及与生物大分子的定位结合.特别对于中间功能化的pDEAAm,有望用于星型聚合物和多臂聚合物的设计和制备.