孤子分子/类噪声脉冲可切换的混合锁模光纤激光器

不同类型脉冲之间的演化是被动锁模光纤激光器丰富动力学的体现。报道了一种可实现多种脉冲切换的混合锁模光纤激光器,当泵浦功率为400 mW时实现了孤子分子、谐波锁模、孤子簇之间的相互切换。增加泵浦功率至600 mW时获得了类噪声脉冲输出,对应的输出功率和单脉冲能量分别为15.2 mW和0.86 nJ。通过调节偏振控制器实现了类噪声脉冲中心波长从1 895 nm到1 930 nm可调谐。所搭建的激光器具有锁模脉冲可切换,波长可调谐,能自启动等优点。     

Linewidth narrowing and polarization control of erbium-doped fiber laser by self-injection locking

A novel and simple self-injection locking (SIL) configuration of distributed feedback (DFB) fiber laser is presented. By injecting the feedback light into the cavity of the fiber laser, it can realize that the line-width can be narrowed by half compared with the same system without SIL. Meanwhile the stable single-polarization lasing is achieved and the degree of polarization is improved from 0.165 to 0.989. Then the self-pulsation behavior of the DFB fiber laser is investigated in the injection-locked and unlocked system respectively and the output power fluctuation is reduced from about 4 to 0.1 dBm by injection locking. And the power output characteristics of the DFB fiber laser are also researched by changing the pump current. With increasing the pump current from 30 to 275 mA, the output power of the DFB fiber laser increases linearly and the injection-locked output increases slightly more quickly than the unlocked output. The results have a great potential application in optical communication and high sensitive fiber sensors.     

两路双包层光纤激光器互注入锁相实验研究

提出了一种利用45°半透半反分束镜和角锥反射器实现两路光纤激光器的能量相互注入,从而获得相干合成激光输出的新方法,分析了其锁相原理.在实验上成功实现了两路独立振荡双包层光纤激光器的互注入锁相输出,在远场观察到了清晰稳定的干涉条纹（可见度约0.57）,获得了超过10W的相干合成激光输出,功率合成效率约为76%.实验表明,这种互注入锁相方法可以在更高功率条件下运行,是光纤激光相干合成领域一种有前途的新技术. 关键词： 光纤激光器 相干合成 互注入锁相     

激光注入误差对多模光纤传能特性影响分析

采用ZEMAX软件对激光光纤注入系统进行了建模,仿真分析了激光注入光纤横向偏移、角度偏移对光纤传输激光能量特性的影响.结果表明,光纤输出激光能量分布与激光注入对准误差密切相关.注入误差引起光纤初始输入段激光峰值功率密度的剧烈波动,出现了一个激光峰值功率密度极大值,这个极大值是可以达到光纤截面内激光平均功率密度的数十倍;横向偏移激发大量斜光线产生,使光纤输出激光能量分布匀化;角度偏移仅影响光纤内子午光线与斜光线的传播方向,对光纤内激光能量分布的匀化作用较弱.     

掺钕保偏光纤激光器的研究

对掺钕光纤激光器输出功率沿光纤的分布以及不同光纤长度下抽运功率和输出功率沿光纤的分布进行了数值模拟.以808nm半导体激光器为抽运源，掺钕双包层保偏光纤为增益介质，对保偏光纤激光器进行了探索性的实验研究.分别就光纤不同弯曲形状和弯曲半径对激光器输出功率指标和偏振特性的影响进行了研究，实验中发现在1060nm和1092nm处有两个峰值.在波长1060nm处得到了7.35W的连续偏振激光输出，斜率效率为58.3％. 关键词： 激光技术 光纤激光器 掺钕保偏光纤 偏振     

同带抽运高效率光纤放大器

以光纤光栅为谐振腔搭建了波长为1020 nm的光纤激光器,并通过两级级联放大获得了590 mW的最大输出功率. 利用获得的波长为1020 nm的激光进行了波长为1064 nm种子光同带抽运放大,实验研究了不同增益光纤长度时放大器的输出功率和转换效率. 当增益光纤长度为8.5 m时,放大器最大输出功率为385 mW,斜率效率为81%. 进行了波长为976 nm的半导体激光器直接抽运波长为1064 nm种子光的实验. 在增益光纤长度最优时,其斜率效率为56.4%. 实验结果表明,同带抽运方式比传统抽运方式具有更高的转换效率. 研究结果可为波长为1020 nm的激光高功率放大和波长为1064 nm的光纤激光高功率同带抽运放大提供一定的参考. 关键词： 同带抽运 光纤放大器 斜率效率     

All-fiber passive mode-locked laser to generate ps pulses based in a symmetrical NOLM

We experimentally investigate an all-fiber passively mode-locked laser generating ps pulses. The experimental setup is a figure eight fiber laser configuration, including a power-symmetric Nonlinear Optical Loop Mirror (NOLM) with highly twisted low-birefringence fiber in the loop. NOLM switching is achieved by polarization asymmetry between the counter-propagating beams in the loop. We used a Quarter-Wave Retarder in the loop to break the polarization symmetry. Using a polarizer beam-splitter cube as the NOLM output we got the best quality output pulses from the laser. At this output, we are monitoring the output pulse polarization component which is parallel to the input NOLM component. We achieved stable generation of ～25 ps pulses at the repetition frequency of 0.78 MHz with milliwatts average output power. The mode-locked laser ran in stable operation for hours.     

28 W环绕式高密度注入波导激光器

报道了一种新型结构形式的环绕式高密度注入波导激光器原理样机。采用环绕式高密度侧面注入技术,利用经过特殊工艺处理的裸增益光纤,当注入泵浦功率320 W时,获得了最高输出功率为28 W的连续激光,斜率效率20%,中心波长1080 nm。结果表明,环绕式高密度注入波导结构形式是可行的,且输出功率和斜率效率具有较大的提升空间。     

强泵浦下掺Yb3+双包层光纤激光器输出特性数值分析和实验研究

对强泵浦下线形腔掺Yb3+双包层光纤激光器输出特性进行了理论和实验研究。通过数值模拟,分析了泵浦光及激光在光纤中的分布、输出功率与泵浦功率的关系、光纤长度及腔镜反射率对激光输出功率的影响。在实验中,利用D型掺Yb3+双包层光纤获得了输出功率10 6W的光纤激光输出,斜率效率达86%。测量了在不同输出耦合条件下的输出功率、阈值泵浦功率和斜率效率,理论分析与实验结果基本一致,为进一步提高光纤激光器功率提供了理论和实验依据。     

Switching of a Semiconductor Laser with Multi-Detuned Optical Inputs by Controlling Injection Current

The multistability of a Fabry-Perot semiconductor diode laser for an injection current is presented when multi-optical inputs detuned from the cavity-resonant wavelength of a semiconductor laser are injected. m+1 Multi-stable states are shown to be produced in the optical output versus injection current characteristics for m detuned optical inputs. It is shown that optical output can be switched in any one of the optical input wavelengths in a relatively fast response time by applying injection current pulses. Analytical expression based on linear stability analysis is presented to predict the switching time to free oscillating mode, and larger optical input power and detuning are effective to shorten the switching time. The results here are believed to be useful to extend wavelength switching to a scope of electronic manipulation without modulation of optical inputs and can be applicable to actual devices.     

Output Characteristics of High-Power Continuous Wave Raman Fiber Laser at 1239 nm Using Phosphosilicate Fiber

A high-power singlemode Raman fiber laser (RFL) with maximum output power of 4.11 W and maximum power conversion efficiency of 47.40% at 1239 nm is realized using continuous wave 8.4 W Yb-doped double-clad fiber laser as a pump, 700 m phosphosilicate fiber, and a Raman cavity formed by a pair of fiber Bragg grating mirrors at 1239 nm. The output characteristics of the RFL at 1239 nm for different fiber lengths and output mirror reflectance are reported. Theoretical simulation is done to numerically optimize for fiber length and output coupler reflectivity to obtain maximum first Stokes power.     

一种掺钕光纤激光器与倍频技术实现的数值模拟

从双包层光纤激光器的速率方程和光传输方程出发，建立数学模型，进行数值计算并对掺钕光纤激光器输出功率沿光纤的分布以及不同光纤长度下抽运功率和输出功率沿光纤的分布进行了数值模拟。以808nm半导体激光器为抽运源，掺钕双包层光纤为增益介质，并以KTP作为倍频晶体，计算并模拟其倍频效率和相位匹配角。最后，对光纤激光器及其倍频的实现进行了模拟研究。结果表明，该光纤激光器能够高效率地实现可见光输出。     

LD泵浦掺铥(Tm3+)光纤激光器的数值分析

首先从掺铥光纤激光器的速率方程和光传输方程出发,建立数学模型,通过Matlab软件进行数值计算,分析了泵浦光和激光沿光纤的分布以及各能级离子数的变化.在不同掺杂浓度下,研究了小信号增益与入纤泵浦功率的关系以及泵浦光和激光功率与增益介质长度的关系.在不同泵浦功率下,研究了输出功率与输出耦合镜反射率的关系.进一步对不同泵浦吸收系数,研究了斜率效率和泵浦阈值与光纤长度的关系.分析结果表明存在最佳光纤长度和最佳耦合输出透过率,使得激光输出功率达到最佳值.     

Integrated injection seeded terahertz source and amplifier for time-domain spectroscopy

We used a terahertz (THz) quantum cascade laser (QCL) as an integrated injection seeded source and amplifier for THz time-domain spectroscopy. A THz input pulse is generated inside a QCL by illuminating the laser facet with a near-IR pulse from a femtosecond laser and amplified using gain switching. The THz output from the QCL is found to saturate upon increasing the amplitude of the THz input power, which indicates that the QCL is operating in an injection seeded regime.     

端面泵浦掺Yb3+双包层光纤激光器

从双包层光纤激光器的速率方程出发，得到了光纤中泵浦光与激光的功率分布、输出功率与泵浦功率的关系、腔镜反射率及光纤长度对输出功率的影响。研究结果表明：输出激光功率与光纤长度及后腔镜反射率有很强的依赖关系，存在一个输出功率最大的最佳光纤长度。后腔镜反射率越大，输出激光功率越小；当光纤长度较短时，在输出端放置反射镜使泵浦光高反射，可以提高输出功率和效率。通过对端面泵浦掺Yb3+双包层光纤激光器进行理论分析和实验研究，得到输出激光的中心波长为1088.3nm，斜率效率为33.7%，最大输出功率为1.75W。     

激光线宽对单次通过PPMgO:LN晶体倍频效率的影响

通过单次穿过PPMgO:LN晶体产生了2.06 W的780 nm可调谐的连续倍频光. 采用1560 nm的分布反馈式(DFB)半导体激光器、光栅外腔半导体激光器(ECDL)和分布反馈式掺铒光纤激光器(DFB-EDFL)分别作为掺铒光纤放大器(EDFA)的注入光源, 所用的EDFA具有保持窄线宽的功能, 因此可以忽略它对基波线宽的展宽. 研究了激光线宽对单次通过PPMgO:LN 晶体的倍频效率的影响. 控制三台激光器各自注入EDFA的功率一致, 同时也保持EDFA 的输出功率. 在基波功率为12.42 W 时, 使用DFB半导体激光器注入EDFA时得到了1.36 W的780 nm倍频光输出, 转换效率为11.0%; 使用ECDL作为种子源时得到了1.78 W 的780 nm倍频光输出, 转换效率为14.3%; 使用DFB-EDFL作为种子源时得到了2.06 W的780 nm倍频光输出, 转换效率为16.6%. 测得三台种子激光器的线宽分别为1.2 MHz (DFB), 200 kHz (ECDL)和600 Hz (DFB-EDFL). 线宽越窄, 倍频效率越高, 实验结果与理论分析一致.     

High efficient Tm3+ doped double cladding silica fiber laser with an intracavity biconical taper

A high efficient LD (laser diode) pumped Tm³⁺ doped double clad silica fiber laser with an intravacity biconical taper was reported. A biconical taper located ～3 cm from the output end of the fiber laser was fabricated by heating and stretching method with a length 1.5 cm and waist diameter ～20 µm. The slope efficiency was 49.8% with respected to the launched pump power, and the maximum output power was 1.97 W. Pre and post output laser power ratio was ～10. This fiber laser was compared with other three biconical tapered fiber lasers (the same fiber with different tapers) and a uniform geometry fiber laser. With intracavity biconical tapers, fiber lasers’ thresholds were ～1 W higher than the fiber laser without the taper (1.97 W). The pump end’s slope efficiencies of fiber lasers with tapers were 3–5% in contrast with 37.6% of the uniform one. After tapered, the pre and post laser power ratios were much higher than the un-tapered one’s, but not changed much with the launched pump power.     

Gain-induced soliton switching in fiber nonlinear directional coupler

With study for switching characteristics and output coupling ratio of fiber nonlinear directional couplers (NLDC), we found that the influence elements on the switching characteristics and output coupling ratio had gain of core 1 and 2, nonlinear coefficient of those, the input power and width of input soliton. We also found numerically that switching efficiencies were improved by controlling gain of core 1, different output coupling ratio would be obtained by controlling gain of core 1 or 2. And we can change the gain by changing pump power of the optical fiber amplifiers. From this, we also made fiber coupler which output coupling ratio was changeable.     

Flat and compact switchable dual wavelength output at 1060 nm from ytterbium doped fiber laser with an AWG as a wavelength selector

A dual-wavelength ytterbium doped fiber laser with a narrowest spacing of 0.53 nm and widest spacing of 12.2 nm at 1064 nm is presented in this paper. An arrayed waveguide grating (AWG) together with an optical channel selector (OCS) have also been incorporated in the proposed setup that works as a switchable mechanism giving 23 different wavelength tunings. Producing an average output power of ?8 dB m and side mode suppression ratio (SMSR) of 59.65 dB, this dual-wavelength fiber laser is quite stable with an output power variance as low as 0.47 dB giving it an advantage due to its switching ability and stable dual-wavelength output powers.     

高功率TEA CO2激光器两波长激光切换输出技术

 以TEA CO₂激光器通常采用的平-凹光学稳定腔为基础,提出了一种新的波长选支方法——输出窗口镀膜选支方法。利用一台高平均功率TEA CO₂激光器进行了选支实验研究,结合现有光学镀膜技术,得到了中心波长为9.3 μm的激光单谱线输出,其单脉冲能量及平均功率与激光器原中心波长10.6 μm单谱线输出的相应参数基本相当。研究发现,以相同单脉冲能量激光照射热敏纸时,中心波长9.3 μm激光光斑与中心波长10.6 μm的明显不同。同时,还设计出两波长窗口密闭免调切换装置,在一台激光器上实现了10.6,9.3 μm两个中心波长激光同等功率水平的免调切换输出,切换位置误差小于5″,密封性能满足使用要求。