Analyses of radiation force and torque on a spherical particle near a substrate illuminated by a focused Laguerre-Gaussian beam

We present the analyses of radiation force and torque on a spherical particle illuminated by Laguerre-Gaussian beam. Since Laguerre-Gaussian beam has angular momentum, the particle can be rotated by illumination of Laguerre-Gaussian beam. Radiation forces and torques for a silver sphere and a silicon sphere near the silver substrate are analyzed. We found that the maximum torque on silicon sphere is about five times higher than the maximum torque on silver sphere and fine control of the focused spot is required to push the particle to the substrate.     

A High Gain and Broadband C-Band Aperture-Coupled Patch Antenna

A aperture-coupled patch antenna is designed with parasitic elements connecting to the rectangle ring on the bottom of antenna substrate through metal vias, which lead the current induced by patch radiator to the top surface of antenna substrate. Therefore, the effective radiation is enhanced and higher gain is achieved. The bandwidth is broadened simultaneously due to the structure of aperture-coupled patch antenna with parasitic elements. Compared to the conventional aperture-coupled patch antenna, the antenna gain increases averagely 2 dB due to the novel structure. Compared to patch antenna of electromagnetic band-gap, the dimensions of novel patch antenna greatly decreases, which can be used as element in the array antenna. Two kinds manufactured antenna are both measured in an anechoic chamber. The good agreements between numerical simulation and experimental prototype have been obtained.     

Au@碳球复合结构中Au颗粒位置调控光吸收

采用时域有限差分（FDTD）法研究Au纳米颗粒@碳球（AuNPs@CS）复合结构的光吸收控制。发现Au纳米颗粒@碳球复合结构中Au颗粒的位置可以控制复合结构光吸收。模型计算中选取两粒Au纳米颗粒以最佳深度（0 nm）嵌入碳球表面。当两粒Au颗粒球心与碳球球心夹角为22.5°和45°时,复合结构光吸收较单一碳球光吸收明显增强;当夹角为315°、270°、180°、90°时,光吸收增量逐渐减小;当夹角为337.5°时,光吸收量低于单一碳球。这一结果主要归因于Au纳米颗粒位置变化可引起表面等离子体光强度和光散射方向的变化。改变碳球表面Au纳米颗粒的数量和位置,可以进一步调节AuNPs@CS复合结构的光吸收。     

基于Wenzel模型的粗糙界面异质形核分析

异质形核是形核发生的主要形式. 经典形核理论对基底界面作了理想化平面假设,然而实际异质形核体系中理想平直的固体界面是不存在的,这导致了异质形核描述与实际情况的偏差. 考察了固相晶胚在非平整界面上的异质形核过程,基于Wenzel润湿模型,分析了非理想界面的粗糙度因子对固相晶胚形核功的影响规律. 结果表明:当基底与晶核之间的本征润湿角小于90°时,基底界面越粗糙越有利于形核;本征润湿角大于90°时,基底界面越粗糙越不利于形核. 同时,游离晶胚在基底上润湿是球冠晶胚形成的重要途径,粗糙界面润湿过程中界面自由能的 关键词： 异质形核 粗糙界面 Wenzel模型 润湿过程     

Wetting property of smooth and textured hydrophobic surfaces under condensation condition

Static and dynamic wetting behaviors of sessile droplet on smooth, microstructured and micro/nanostructured surface under condensation condition are systematically studied. In contrast to the conventional droplet wetting on such natural materials by dropping, we demonstrate here that when dropwise condensation occurs, the sessile droplet will transit from the Cassie-Baxter wetting state to the Wenzel wetting state or partial Cassie-Baxter wetting state on the microstructured surface or the micro/nanostructured surface, which leads to a strong adhesion between the droplet and the substrate. In contrast, the apparent contact angle and the sliding angle on the smooth surface changes a little before and after the condensation because of small roughness. Theoretical analysis shows that the roughness factor controls the adhesion force of the droplet during condensation, and a theoretical model is constructed which will be helpful for us to understand the relationship between the adhesion force and the geometry of the surface.     

Micro-structure and frictional characteristics of beetle''s joint

Geometric and micro-structure design, tribology properties of beetle joints were experimentally studied, which aimed to enlighten ideas for the joint design of MEMS.The observation by using SEM and microscopy suggested that beetle's joints consist of a concave surface matched with a convex surface. The heads of the beetles, rubbing with flat glass, were tested in fresh and dried statuses and compared with sapphire ball with flat glass. Frictional coefficient of the joint material on glass was significantly lower than that of the sapphire sphere on glass. The material of the joint cuticle for convex surface is rather stiff (the elastic modulus 4.5 Gpa) and smooth. The surface is hydrophobic (the contact angle of distilled water was 88.3° ). It is suggested here that the high stiffness of the joint material and hydrophobicity of the joint surface are parts of the mechanism minimizing friction in insect joints.     

Micro-structure and frictional characteristics of beetle’s joint

Geometric and micro-structure design, tribology properties of beetle joints were experimentally studied, which aimed to enlighten ideas for the joint design of MEMS. The observation by using SEM and microscopy suggested that beetle’s joints consist of a concave surface matched with a convex surface. The heads of the beetles, rubbing with flat glass, were tested in fresh and dried statuses and compared with sapphire ball with flat glass. Frictional coefficient of the joint material on glass was significantly lower than that of the sapphire sphere on glass. The material of the joint cuticle for convex surface is rather stiff (the elastic modulus 4.5 Gpa) and smooth. The surface is hydrophobic (the contact angle of distilled water was 88.3°). It is suggested here that the high stiffness of the joint material and hydrophobicity of the joint surface are parts of the mechanism minimizing friction in insect joints.     

Exact solution for the scattering and absorption properties of sphere clusters on a plane surface

A formulation and computational scheme are presented for predicting the scattering and absorption cross-sections, and the scattering matrix elements, of clusters of non-intersecting spheres that are lying on or above an infinite plane surface and exposed to plane-wave radiation. The formulation provides an exact solution to Maxwell's equations and the associated boundary conditions on the spheres and the plane surface, and is applicable for arbitrary refractive indices for the spheres and the surface. A simplified strategy is presented for the calculation of the surface reflection matrix, which transforms the reflected scattered field from one sphere into a regular vector spherical harmonic expansion centered about another sphere. The calculation results are presented for the clusters of one, two, and four polystyrene spheres, with size parameters of one and 10, lying on a silicon substrate, and are compared with the predictions from the normal incidence approximation (NIA) in which the reflectance of the surface is assumed constant at the normal incidence value. The results show that the accuracy of the NIA is highly dependent on the extent of the sphere cluster, the angle of incidence, and the particular quantity (cross-sections, scattering matrix elements) under examination.     

Spin transfer torque in the semiconductor/ferromagnetic structure in the presence of Rashba effect

Spin transfer torque in magnetic structure occurs when the transverse component of the spin current that flows from the nonmagnetic medium to ferromagnetic medium is absorbed by the interface. In this paper, considering the Rashba effect on the semiconductor region, we discuss the spin transfer torque in semiconductor/ferromagnetic structure and obtain the components of spin-current density for two models:(i) single electron and(ii) the distribution of electrons. We show that no matter whether the difference in Fermi surface between semiconductor and Fermi spheres for the up and down spins in ferromagnetic increases, the transmission probability decreases. The obtained results for the values used in this article illustrate that Rashba effect increases the difference in Fermi sphere between semiconductor and Fermi sphere for the up and down spins in ferromagnetic. The results also show that the Rashba effect, brings an additional contribution to the components of spin transfer torque, which does not exist in the absence of the Rashba interaction. Moreover, the Rashba term has also different effects on the transverse components of the spin torque transfer.     

Surface modes and optical absorption of a small sphere above a substrate

An exact derivation of the electrostatic surface modes of a sphere above a substrate is presented. The absorption spectrum of the sphere is calculated and compared with that of an isolated sphere. The interaction with the substrate causes the main absorption peak to shift to the low frequency side, and also gives rise to additional absorption peaks. The deficiencies of the dipole approximation, which is often used, are discussed.     

A phenomenological explanation for the buckling of surface alloys

A phenomenological model, in which the interactions between the nearest-neighbor (NN) atoms are described as bondings but not hard sphere contacts, is proposed to explain the unexpected reduced buckling in surface alloy systems. In the model, the forces acting on an adsorbate atom from its NN substrate atoms in different layers may be either repulsive or attractive, depending on whether the bond between the adsorbate atom and its NN substrate atoms is compressed or stretched. It is found that the forces on the adsorbate atom from its NN substrate atoms in the sub-surface layer play a more important role for the buckling of surface alloy than those from its NN substrate atoms in the surface layer do. The bucklings expected by the model are significantly smaller than those predicted by the simple hard sphere model and are in good agreement with the experiments when the equilibrium bond length of the NN adsorbate-substrate atom pairs is taken as the sum of the corresponding metal radii.     

Patchy胶体粒子的结晶、玻璃化和凝胶化问题

本文探讨了中性多缔合位点Patchy胶体粒子系统的相图及其相关问题. 在研究中,计入了分子间的硬芯Lennard-Jones势和缔合作用,进而阐明了系统的流体相(F),无规密积相(RCP)和面心立方相(FCC)之间转变的相态结构. 在体系丰富的相结构中,F-F,F-RCP及F-FCC相转变以及描述粒子间联结性的溶胶-凝胶转变相互影响,致使一些相态在不同相互作用强度时可以呈现亚稳态和稳态. 同时,本文重点阐述了缔合能量以及patch数目对体系的临界温度、临界密度、临界三相点以及溶胶-凝胶转变等的调控机制.     

Field Enhancement by a Metallic Sphere on Dielectric Substrates

We calculate the scattered local field around a small gold sphere on dielectric substrates which is illuminated by a collimated monochromatic beam. The numerical results show the field between the sphere and the substrate is much enhanced when the sphere is illuminated by a p-polarized beam. The enhanced area is very localized between the sphere and the substrate and the diameter of the enhanced area on the surface of the substrate is one fifth of the sphere diameter. The field increases as the gap distance decreases or as the refractive index of the substrate increases.This paper was originally presented at the 5th International Conference on NEAR FIELD OPTICS and RELATED TECHNOLOGIES (NFO-5), which was held on December 6–10, 1998 at Coganoi Bay Hotel, Shirahama, Japan, in cooperation with the Japan Society of Applied Physics and Mombusho Grant-in Aid for Scientific Research on Priority Area “Near-field Nano-optics” Project, sponsored by Japan Society for Promotion of Science.     

Investigation of patch antennas based on crossed idiosyncratic PBG structure

The method of finite difference time domain (FDTD) was used, and characteristics of the patch antenna based on drilling periodic air holes in the substrate were studied, the results indicate that the surface waves which propagate along the surface of the substrate can be suppressed by the crossed idiosyncratic PBG (photonic crystal band-gap) structure because of its effect of forbidden-band, that it can radiate most of electromagnetic waves’ energy in the substrate significantly, and that it has lower return loss (S11) compared to the conventional patch antennas, thus, a high gain is attained, its performance is improved. Due to these advantages, the use of photonic crystal patch antennas will be extended in areas such as mobile communication, satellite communication, aviation, etc.     

Theoretical and Experimental Study of Scattering of a Plane Wave by an Inhomogeneous Plasma Sphere

Scattering of electromagnetic waves by an inhomogeneous plasma sphere has been studied theoretically and experimentally. The offset angles of electromagnetic waves caused by the plasma sphere have been observed experimentally. The effects of the electromagnetic wave frequency and plasma density on the offset angle are discussed. The plasma density is estimated with the offset angle.     

近距离牛顿反平方定律实验检验进展

为了统一描述自然界的四种基本相互作用,科学家提出了很多理论模型,其中很多理论认为牛顿反平方定律在近距离下会发生偏离,或存在其他的非牛顿引力作用,而理论的正确与否需要高精度的实验检验.国际上很多研究组在不同间距下采用不同的技术对反平方定律进行了高精度的实验检验,本文重点介绍华中科技大学引力中心采用密度调制法分别在亚毫米与微米范围进行的实验研究进展.在亚毫米范围采用精密扭秤技术,在对牛顿引力进行双补偿、抑制电磁干扰后,结合零实验与非零实验结果,在作用程为70—300μm区间对Yukawa形式的破缺给出国际上精度最高的限制.在微米范围采用悬臂梁作为弱力传感器,通过测量金球和密度调制吸引质量间水平力的变化来检验非牛顿引力是否存在,实验结果不需进行Casimir力和静电力背景扣除,是此间距下不依赖于Casimir力和静电力理论计算模型的两个结果之一.     

Optical and magneto-optical resonances in nanocorrugated ferromagnetic films

We report here on optical and magneto-optical spectra investigations of nanostructured Co and Ni films deposited on top of polymethyl methacrylate (PMMA) colloidal crystal. Resonant peculiarities have been observed in both spectra; their positions are scaled with the PMMA sphere diameter and depend on incident angle. Asymmetry of the resonance lineshapes as well as change of the direction of magneto-optical rotation has been observed. Both the surface plasmon resonance and the interference between reflections from the colloidal crystal and from the nanostructured film should be considered to explain the obtained results.     

基于近红外光谱的柔性基底紫外臭氧改性效果表征研究

近年来,随着纳米科技、聚合物材料和先进制造技术的发展,以柔性传感器为代表的新兴柔性电子器件在可穿戴、健康医疗、物联网终端等领域发挥着越来越重要的作用。作为柔性电子器件的载体,柔性基底对传感器的机械可靠性和电学传感性能等方面有着重要的意义。但由于其表面非极性键造成的高疏水性限制了功能性材料在其表面的沉积,常常造成柔性基底层与电极层/敏感层之间不稳定的界面结合。因此,利用紫外臭氧处理对柔性基底表面改性受到了广泛的关注。利用近红外光谱技术对柔性基底的紫外臭氧处理效果进行快速精准评估,旨在从基团分子层面探究其改性效果,在实际应用中是对传统依靠接触角测量评估方法的有效补充。具体而言,对四种常见的柔性基底材料聚二甲基硅氧烷(PDMS)、聚萘二甲酸乙二醇酯（PEN）、聚对苯二甲酸乙二醇酯（PET）和聚酰亚胺（PI）进行了1/2/5/10 min不同时长的紫外臭氧（UVO）改性处理,并利用近红外光谱对其改性效果进行表征研究,最后利用接触角测量方法对上述的表征结果进行了验证分析。近红外光谱分析表明：对于柔性PDMS基底,紫外光能量不足以切断其中的甲基（—CH₃）官能团和（—C—Si—）等化学键,无法引入羟基、羧基等亲水性基团。对于柔性PEN和PET基底而言,紫外臭氧处理的效果要优于柔性PDMS基底,且对柔性PET基底的处理效果要优于柔性PEN基底,其原因可能是PEN基底材料中萘环的双环结构具有很强的紫外光吸收能力,阻隔了380 nm以下的大部分紫外线能量。对于柔性PI基底,紫外臭氧处理可以有效引入羟基（—OH）和羧基（—COOH）等活性基团,且这些官能团的强度和数量随着处理时间的增加而增加,从而在短时间内使得PI基底表面能增大、接触角减小、湿润性提高。接触角测试结果验证：紫外臭氧处理对于柔性PDMS基底处理效果不明显（接触角下降幅度为8.4%）;对柔性PET基底处理的效果（接触角下降幅度为39.6%）要优于柔性PEN基底的处理效果（接触角下降幅度为9.4%）;紫外臭氧处理的效果对柔性PI基底处理效果最佳,接触角下降幅度达到了62.7%。     

Angular dependence of vertical force and torque when magnetic dipole moves vertically above flat high-temperature superconductor

The interaction between a permanent magnet (PM) assumed as a magnetic dipole and a flat high-temperature superconductor (HTS) is calculated by the advanced frozen-image model. When the dipole vertically moves above the semi-infinite HTS, the general analytical expression of vertical force and that of torque are obtained for an arbitrary angle between the magnetization direction of the PM and the c axis of the HTS. The variations of the force and torque are analyzed for angle and vertical movements in both zero-field cooling (ZFC) condition and field cooling (FC) condition. It is found that the maximum vertical repulsive or attractive force has the positive or negative cosine relation with the angle. However, the maximum torque has the positive or negative sine relation. From the viewpoint of the rotational equilibrium, the orientation of the magnetic dipole with zero angle is deemed to be an unstable equilibrium point in ZFC, but the same orientation is considered as a stable equilibrium point in FC. In addition, both of the variation cycles of the maximum force and torque with the angle are π.     

一种高增益低雷达散射截面的新型圆极化微带天线设计

设计了一种基于人工电磁材料覆层的高增益低雷达散射截面(radar cross section, RCS)圆极化微带天线. 人工电磁材料覆层是由介质板及其两侧的人工周期表面构成, 上表面是加载集总电阻的方环贴片, 具有宽带吸波特性; 下表面是开条带缝和圆环缝的金属贴片, 具有部分反射特性. 将其加载到圆极化微带天线上方, 通过覆层上表面的电阻可吸收入射的雷达波, 结合下表面与接地板构成Fabry-Perot谐振腔的多次反射, 可实现圆极化微带天线辐射和散射性能的同时改善. 实测结果表明: 加载人工电磁材料覆层后, 天线的相对轴比带宽由5.9%扩展为7.1%; 天线增益在整个工作频带内都得到了提升, 最大提高了6.61 dB; 天线RCS在宽频带宽角域内实现了明显的减缩, 在天线工作频带内也实现了3 dB以上减缩. 实测结果与仿真结果符合较好.