层状粘接结构超声检测信号的同态解卷积脱粘界面定征

本文利用建立的多层粘接结构超声无损检测信号的卷积模型,推导出了检测信号的解析表达式,并用同态滤波解卷积方法有效地提取出粘接结构的系统响应,进而由其中界面多次反射响应的位置、幅度和包络等特征参数,实现了脱粘二界面（指空气脱粘）的定征和识别。仿真和实验数据的处理结果表明本文方法对脱粘检测的应用有积极的意义。     

多层粘接结构中脱粘界面的人工神经网络余弦变换谱特征识别

针对钢-橡胶多层粘接结构中界面脱粘的超声检测难题,利用余弦变换(DCT)提取的表征检测信号的模式特征矢量,通过人工神经网络模式识别方法对不同界面脱粘时实验检测信号的正确识别,实现了脱粘一、二、三和四界面的检测。本文脱粘界面信号模式的人工神经网络识别系统对现代工业中NDT&NDE的自动化有着积极的意义。     

钢-混凝土结构弱粘接界面缺陷的超声导波检测

钢-混凝土结构是土木工程中的一种常用结构形式,钢与混凝土粘接处可能出现弱粘接甚至完全脱粘的缺陷,严重影响结构的安全性。该文提出利用空气耦合超声导波衰减的方法实现钢-混凝土结构粘接状态的非接触无损检测方法,分析不同厚度粘接界面对超声导波衰减的影响。基于全局矩阵技术对钢-混凝土结构求解理论频散方程和衰减曲线,得到界面层不同粘接条件下的理论参数及衰减特性。建立不同粘接条件的有限元模型,定量分析不同模态对粘接缺陷的检测敏感度。研究界面层厚度分别为1 mm和2 mm两种情况下S0能量的衰减情况。研究结果表明:S0模态可有效判断粘接结构的粘接状态,对于同一界面层厚度,随着界面粘接条件变弱,S0最大幅值与A0最大幅值比不断增大;不同厚度同一粘接条件下,2 mm相较于1 mm该值更大。该方法在钢-混凝土结构粘接界面缺陷的检测方面具有良好的应用价值和发展前景。     

电磁超声界面回波瞬时图谱分析与神经网络识别

针对钢板背后多层橡胶粘接结构,选择较佳实验频率值作为电磁声换能器的激励源频率。提取了检测回波的瞬时振幅、瞬时相位和瞬时频率三种瞬时参数,将瞬时参数构成三维瞬时图谱定性识别不同粘接状态。将敏感时间窗内的平均瞬时参数组成特征向量,利用BP神经网络进行识别,对训练集与测试集的识别结果表明,该方法可以实现电磁超声界面回波的自动识别与分类,识别正确率不低于95%。     

电磁超声多界面检测信号去噪方法研究

为了解决传统压电超声换能器检测方式耦合不稳定的问题,将电磁超声应用于多层粘接结构界面检测。针对电磁超声界面检测信号噪声高和盲区大的问题,在电磁声换能原理和盲区成因分析的基础上,用小波阈值滤波和自适应抵消滤波方法对检测信号进行了处理,达到了降低信号噪声和减小盲区的目的。对钢板和双层橡胶粘接样品的回波信号处理结果表明:小波阈值滤波将信噪比提高了约12 dB,自适应抵消滤波有效地减小了由感生信号产生的盲区。     

脱粘界面超声检测信号的小波多分辨率分析与重构

针对钢-橡胶分层粘接结构的超声检测回波信号,利用小波变换的多分辨率时频特性提出了小波特征参数提取算法,据此在对检测信号进行的时间-尺度分布分析基础上,重构出脱粘界面回波信号的时域和频域特征。实验检测结果表明本文方法在现代工业NDT&E中的应用有着可喜的前景。     

接触缺陷的振动调制超声导波检测技术研究

针对常规线性超声检测方法无法实现板结构接触类缺陷(如微裂纹、脱粘等)检测问题,将超声导波技术与振动声调制技术相结合,利用稀疏分布传感器发展了一种板结构中接触缺陷非线性超声检测方法。通过低频振动改变缺陷的接触状况,使得通过接触面的高频导波信号的相位和幅值受到调制。对受低频振动调制的超声导波二维时间序列进行时频分析,由于接触类缺陷的存在,在振动调制超声导波序列的时频分布上出现明显的低频振动频率分量。利用提取出的低频振动频率下的超声导波信号,进行了结构接触缺陷成像处理。检测试验表明,基于振动声调制的超声导波缺陷成像方法可以实现结构中的接触类缺陷检测。     

玻璃纤维蜂窝复合材料的太赫兹无损检测技术(英文)

采用双高斯脉冲反卷积滤波技术对太赫兹时域波形进行滤波优化,提出一种基于太赫兹时域光谱无损检测的太赫兹反射式层析成像技术,用于分析玻璃纤维蜂窝复合材料的粘接质量.结合玻璃纤维蜂窝复合材料结构的特点,分别在蜂窝上层胶膜和下层胶膜中设计了不同直径的圆形和梯形脱粘缺陷,在此基础上,完成了脱粘缺陷蜂窝结构样品的制作.提出的太赫兹反射式层析成像和B-scan成像方法,适用于玻璃纤维蜂窝复合材料的脱粘缺陷分析.针对反射式层析成像图像对比度差的问题,结合脱粘缺陷处的太赫兹时域波形数据特征,采用缺陷特征时间区域成像优化技术,提高了脱粘缺陷的检测能力和识别准确率,实现了玻璃纤维蜂窝材料的上层脱粘厚度50μm、下层脱粘厚度50μm缺陷的太赫兹无损检测.     

脱粘缺陷对粘接结构频散特性的影响

采用全局矩阵理论,通过引入内聚强度弱化模型和弹簧模型,计算了脱粘缺陷对粘接结构频散特性的影响。分析了内聚强度缺陷、界面缺陷及混合缺陷等因素对粘接结构频散特性的影响,发现频散曲线的演化规律与材料声学性质密切相关。不同材料和不同组合,其规律有很大不同。针对各向同性粘接结构,可能通过考察特定频率段内频散模态的变化,实现对脱粘缺陷的检测。     

复合材料脱粘缺陷的红外热像无损检测

以固体火箭发动机中的玻璃纤维复合材料壳体/绝热层试件的脱粘缺陷为研究对象,利用脉冲闪光灯热激励方式对试件进行加热,用红外热像仪实时监测试件的表面温度场,由表面温度差异来判定试件内部缺陷,然后通过对热像图进行图像增强处理和分割以定量识别缺陷。将实验结果与超声C扫描检测结果进行的对比分析表明:红外热像无损检测方法能够快速直观地发现深度5 mm以内、直径10 mm以上的脱粘缺陷,而超声C扫描检测更适合于对特定缺陷进行准确定量检测。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.