PMMA纳米球的制备及其银膜包覆技术

采用无皂乳液聚合法制备了单分散、直径为170 nm左右的聚甲基丙烯酸甲酯(PMMA)纳米球, 然后利用3-甲基丙烯酰氧基丙基三甲氧基硅烷(MATS)和3-巯丙基三甲氧基硅烷(MPTMS)对PMMA纳米球进行表面改性, 在其表面包覆一层均匀的巯基, 通过巯基与银离子之间的相互作用, 使银在PMMA纳米球表面成核长大, 从而合成PMMA/Ag纳米球壳粒子. 通过扫描电子显微镜、投射电子显微镜和紫外-可见吸收光谱测试技术对产物性能进行了表征, 研究结果表明, 制备的PMMA/Ag纳米球壳粒子的分散性好、包覆均匀.     

制备方法对模板法制备SiO_2中空微球形貌的影响

模板法是制备无机中空微球的重要方法之一.首先通过苯乙烯和甲基丙烯酸的无皂乳液聚合法制得表面含羧基、粒径为360nm的单分散聚苯乙烯(PSt)乳胶粒,并以此为模板,分别采用表面改性-前驱体水解法(PHC)和SiO2纳米颗粒层层自组装法(LBL),制备出了不同壳层厚度的PSt/SiO2核壳结构复合微球,然后经500℃煅烧4h,得到SiO2中空微球.利用透射电镜和扫描电镜对微球结构形态进行了表征.研究表明,首先利用γ-氨丙基三乙氧基硅烷(KH-550)对PSt模板微球进行表面改性、然后再在乙醇-水混合介质中进行原硅酸乙酯(TEOS)水解与缩合反应的PHC法,是制备PSt/SiO2核壳结构复合微球的简便方法,复合微球经煅烧可制得表面均匀、结构致密、壳层厚度和形貌可控的SiO2中空微球;而LBL法制备PSt/SiO2核壳结构复合微球的工艺复杂,煅烧后所得SiO2中空微球结构疏松,易于破碎.     

无皂乳液聚合法制备聚甲基丙烯酸甲酯包覆厚度可控的纳米核-壳二氧化硅微球

用改进的Stöber法和无皂乳液聚合法制备窄分布的二氧化硅/PMMA核-壳纳米微球. 用改进的Stöber法将3-乙氧基甲基丙烯酸丙基硅烷(MPS)修饰在纳米的二氧化硅表面后, 用无皂乳液聚合法制备核-壳纳米微球. 该法简单有效且得到厚度均匀的聚合物包覆层. 随着单体MMA用量的增加, 用动态光散射法测量, PMMA壳层的厚度从6.4 nm增加到96.3 nm. 热重分析表明, PMMA的含量从22.25%增加到93.41%. 扫描电子显微镜和透射电子显微镜结果表明, 得到的是包覆良好、表面光滑的核-壳无机/聚合物纳米微球.     

结构型载体负载纳米银合成及催化性能

通过两步聚合法合成具有温度敏感性能的核-壳型聚(苯乙烯-N-异丙基丙烯酰胺)/N-异丙基丙烯酰胺共聚3-(甲基丙烯酰氧)丙基三甲氧基硅烷(P(St-NIPAM)/P(NIPAM-co-MPTMS))复合微凝胶材料.以经3-巯丙基-三甲氧基硅烷(MPS)表面修饰的复合微凝胶为载体,乙醇为还原剂,在温和条件下控制性还原制备纳米银微粒.通过扫描电子显微镜(SEM)、透射电子显微镜(TEM)、傅里叶变换红外(FT-IR)光谱仪、X-射线光电子能谱(XPS)、X射线衍射(XRD)仪、热分析(TGA)和紫外-可见(UV-Vis)分光光度计等手段对P(St-NIPAM)/P(NIPAM-co-MPTMS)-(SH)Ag复合微凝胶的结构、组成和性质进行表征.同时,以硼氢化钠还原对硝基苯酚为模型反应,对该复合材料催化还原性能进行了评价.结果表明,载体含有巯基的有机-无机杂化网络结构的限域作用使原位合成的纳米银微粒的分散性较好.载体微凝胶壳层链节中无机组分MPTMS的引入在一定程度上降低了复合凝胶温敏性,但复合凝胶仍表现出催化还原反应的温敏性调控和良好的催化活性.以上实验结果与温敏性PNIPAM链节被无机网络分隔而有利于反应传质及壳层巯基对原位纳米银形成尺寸和空间分布的有效控制有关.本研究对功能性金属纳米催化复合材料的研究具有积极借鉴意义.     

磁性荧光纳米材料的制备与性能

采用表面活性剂3-氨丙基三乙氧基硅烷(APTES)修饰Fe₃O₄磁性纳米粒子, 经质子化后, Fe₃O₄磁性纳米粒子表面披覆大量的正电荷, 与表面带负电荷的巯基丙酸(MPA)修饰的核壳CdSe/CdS/ZnS量子点(QDs)通过强烈的静电作用而发生组装, 得到兼具磁性和荧光性能的磁性荧光纳米材料. 利用透射电子显微镜(TEM)、傅里叶变换红外光谱仪(FTIR)、X射线衍射仪(XRD)、荧光分光光度计和振动样品磁强计(VSM)等测试手段对磁性荧光纳米材料进行表征. 研究表明, 由两种粒子组装的核壳结构复合粒子拥有良好的磁性能和荧光性能.     

种子表面改性法制备核壳结构PSt/SiO_2复合微球

首先采用无皂乳液聚合法合成了表面带负电荷、粒径为360nm的单分散聚苯乙烯(PSt)种子乳液,并以EtOH/H2O混合物为分散介质,利用γ-氨丙基三乙氧基硅烷(KH-550)在25℃下对PSt微球表面进行改性,得到了表面硅烷化并带有正电荷的改性PSt种子乳液,然后在碱性条件下加入原硅酸乙酯(TEOS)使其和微球进行共水解与共缩聚,制备出了核壳结构PSt/SiO2复合微球,并利用电镜对复合微球的结构形态进行了表征.研究表明,PSt种子乳液改性时体系的zeta电位随着KH-550用量的增加而升高,当KH-550用量为PSt种子重量的1/3时,体系的zeta电位从原来的-34.5mV升高到了38mV,达到对PSt微球表面改性的最佳值;在制备PSt/SiO2复合微球时,TEOS水解缩聚形成的SiO2包覆到改性微球上的量随着反应时间的延长而增加,反应24h时达到97.9%的最大值;随介质中水含量的增加,吸附到复合微球表面上的SiO2纳米颗粒逐渐减少,复合微球表面逐渐变得光滑,当EtOH/H2O质量比降低到60/28.5时,得到结构均一、壳层厚度为35nm的核壳结构PSt/SiO2复合微球。     

钛酸四丁酯水解制备聚苯乙烯/二氧化钛核壳粒子及空心二氧化钛微球

通过无皂乳液聚合方法制备了阳离子型及阴离子型聚苯乙烯(PSt)乳胶粒,并对后者用γ-氨丙基三乙氧基硅烷(KH550)进行了表面改性制得了乳胶粒表面载正电荷的乳液.在乙醇与水的混合溶剂中,分别使用以上3种PSt乳胶粒为核加入钛酸四丁酯制备了核壳型PSt/TiO2复合粒子.结果显示,仅在使用经KH550改性的阴离子PSt乳...     

聚苯胺/聚苯乙烯复合Janus颗粒的制备

利用有机溶剂溶胀磺化聚苯乙烯@二氧化钛(SPS@TiO₂)核壳粒子制得二氧化钛/聚苯乙烯(TiO₂/PS)双面神(Janus)颗粒, 并在TiO₂端进行改性, 得到墨绿色的聚苯胺/聚苯乙烯(PANi/PS) Janus颗粒. 用扫描电子显微镜(SEM)、电子能谱(EDS)、元素分析、透射电子显微镜(TEM)、红外光谱(IR)、热重分析(TGA)、固体紫外-可见分析(UV-Vis)和四探针法考察Janus颗粒组成、微结构和Janus性质. 结果表明, Janus颗粒为雪人状结构, PS端的平均粒径为228 nm, PANi端的平均粒径从TiO₂的258 nm增大为295 nm; 并且在EDS谱上可以观察到N元素, 而未观察到Ti元素; 包覆的PANi的质量分数为23.7%. 掺杂后PANi/PS Janus颗粒的导电性能较好, 电导率为0.247 S/cm.     

乙烯基化的中空二氧化硅球的制备与表征

在乙醇/氨水介质中,以分散法制备的聚苯乙烯微球为模板,通过乙烯基三乙氧基硅烷水解缩合反应在聚苯乙烯表面形成包覆层.然后将聚苯乙烯球核溶解而制备了乙烯基化二氧化硅空心微球.     

Pickering乳液聚合制备核-壳结构PS-SiO2复合微球

用二氯二甲基硅烷对纳米SiO2粒子进行疏水改性,当其表面Zeta电位由-54.8 mV变成-25.8 mV时,SiO2粒子就能在苯乙烯-水界面自组装,形成稳定的Pickering乳液,即以胶体粒子为乳化剂的乳液.利用Pickering乳液聚合制备了以聚苯乙烯(PS)为核、纳米SiO2为壳的PS-SiO2复合微球.用FT-IR、XPS、SEM、偏光显微镜等对复合微球进行了表征.结果表明:复合微球由聚苯乙烯和纳米二氧化硅粒子组成,二氧化硅粒子以单层、六方密排的方式分布在聚苯乙烯微球表面.     

Synthesis of novel tantalum oxide sub-micrometer hollow spheres with tailored shell thickness

Sub-micrometer-sized hollow tantalum oxide (Ta2O5) spheres with tunable shell thickness and void size have been fabricated exploiting beta-diketone-functionalized polystyrene (PS) beads as sacrificial templates in a sol-gel process. First, a controlled precipitation of Ta2O5 nanoparticles was carried out on the template surface by hydrolyzing tantalum ethoxide (Ta(OEt)5) at room temperature, and subsequently, the polymer core was removed either via chemical treatment with toluene or calcination at 650 degrees C. The thickness of the tantala shell precipitated on the PS core during the coating process was tuned between 100 and 142 nm by varying the concentration of tantala precursor in the reaction media. The obtained Ta2O5-coated PS particles and hollow microspheres were characterized by scanning electron microscopy, transmission electron microscopy, infrared spectroscopy, X-ray diffraction, and thermogravimetric analysis. Due to the unique optical and dielectric properties, these nanostructured materials are envisaged to be used in applications such as novel building blocks for the fabrication of advanced materials, surface coatings, catalysts, and drug delivery systems.     

Synthesis of hierarchical hollow silica microspheres containing surface nanoparticles employing the quasi-hard template of poly(4-vinylpyridine) microspheres

A facile method of preparing hierarchical hollow silica microspheres containing surface silica nanoparticles (HHSMs) through the sol-gel process of tetraethylorthosilicate employing a quasi-hard template of non-cross-linking poly(4-vinylpyridine) microspheres is proposed. The quasi-hard template contains the inherent catalyst of the basic pyridine group, and a few of the polymer chains can escape from the template matrix into the aqueous phase, which initiates the sol-gel process spontaneously both on the surface of the template used to prepare the hollow silica shell and in the aqueous phase to produce the surface silica nanoparticles. By tuning the weight ratio of the silica precursor to the quasi-hard template, HHSMs with a size of about 180 nm and a shell thickness ranging from 14 to 32 nm and surface silica nanoparticles ranging from 17 to 36 nm are produced initially through the deposition of surface silica nanoparticles onto the silica shell, followed by template removal either by calcination or solvent extraction. The synthesized HHSMs are characterized, and a possible mechanism for the synthesis of HHSMs is proposed.     

金纳米棒@碳中空胶囊的制备及催化性能

以聚吡咯为碳壳前驱体制备了金纳米棒镶嵌于碳壳内的中空胶囊.先合成羧基修饰的聚苯乙烯微球和十六烷基三甲基溴化铵稳定的金纳米棒; 再利用二者之间的静电力将金纳米棒组装在聚苯乙烯微球表面; 最后, 通过氧化聚合将聚吡咯壳包覆在聚苯乙烯@金纳米棒复合物的表面.在氮气保护下经高温煅烧, 聚吡咯壳被碳化为碳壳的同时聚苯乙烯微球分解, 从而制得金纳米棒@碳中空胶囊.在煅烧过程中, 由于碳壳的保护, 金纳米棒很好地保持了“棒状”形貌.通过调节吡咯单体的浓度, 可以控制聚吡咯壳和碳壳的厚度.金纳米棒@碳中空胶囊在以NaBH₄为还原剂还原亚甲基蓝的反应中表现出良好的催化活性.     

Engineering Surface Patterning of Colloidal Rings through Plateau–Rayleigh Instability

Plateau–Rayleigh (P‐R) instability occurring on Brownian colloidal particles is presented. This instability can be used for the surface patterning of Brownian colloidal rings. This idea was realized by employing polystyrene(PS)/SiO₂ core/shell rings, for which PS layer was selectively grown onto the interior surface of SiO₂ rings. The P‐R instability was initiated in the ring's dispersion by adding a good solvent of PS. By using both experiments and theory, it is shown that the number of patches is tunable and that it is linearly related to a function of two variables, namely, solvent quantity and contact angle. In particular, one‐patch Janus rings and patchy disks were also synthesized at high yields. The patch size of all particles is tunable by step‐by‐step polymerization and the patches can be functionalized, for example by ATRP grafting with pH‐sensitive polymers. This approach can be adapted for the synthesis of other patchy colloids with designated complexity.     

基于自组装溶胶凝胶法无机Janus纳米片的制备及其乳化性能研究

论文首先采用水解苯乙烯-马来酸酐共聚物为乳化剂,正硅酸乙酯、亲油性硅烷偶联剂和亲水性硅烷偶联剂三种前驱体溶于石蜡做为油相(分散相),水为连续相,乳化分散后通过溶胶凝胶法,制备得到了表面亲水/内部亲油的核壳实心微球;然后超声清洗除去石蜡后得到了表面亲水/内部亲油的二氧化硅空心球,将其破碎后即得到了无机Janus纳米片.实...     

聚合物接枝Janus纳米片形变的耗散粒子动力学研究

由于在检测、药物输运、分子马达等领域具有广阔的应用前景,二维柔性响应Janus材料受到了广泛的关注。但遗憾的是,这些二维材料的响应形变的分子机理仍不明确。基于此,我们采用介观尺度的耗散粒子动力学模拟方法系统研究了Janus纳米片两侧接枝不同长度和不同溶剂相容性的高分子链对Janus纳米片形变的影响。我们发现由于构象熵和混合焓的共同作用,通过对接枝链长度和溶剂相容性的调整,Janus纳米片可以形成如反相包覆、信封装包覆和碗状等新奇的结构。我们的理论结果首次提供了对二维柔性Janus材料可控形变的基本认识,并预报了设计合成新型Janus纳米器件在药物和生物医学领域的潜在应用。     

Hollow titania spheres with movable silica spheres inside

We demonstrate a flexible method for preparing hollow TiO2 nanospheres with movable silica nanoparticles inside (HTNMSNs). In this method, we used monodisperse silica--polystyrene core--shell nanospheres (SiO2-PS-CSNs) sulfonated as templates and prepared the composite shell consisting of TiO2 and sulfonated polystyrene (SPS) through adsorbing or depositing tetrabutyl titanate gel into the SPS shell. Finally the HTNMSNs were obtained after removal of all polymers in the composite nanospheres by dissolution or calcinations. We investigated the dependence of the morphologies of HTNMSNs on the thickness of PS shells and the size of SiO2 cores and prepared rare earth doped HTNMSNs by a sol-gel process.     

Fabrication of carbon microcapsules containing silicon nanoparticles-carbon nanotubes nanocomposite by sol-gel method for anode in lithium ion battery

Carbon microcapsules containing silicon nanoparticles (Si NPs)-carbon nanotubes (CNTs) nanocomposite (Si-CNT@C) have been fabricated by a surfactant mediated sol-gel method followed by a carbonization process. Silicon nanoparticles-carbon nanotubes (Si-CNT) nanohybrids were produced by a wet-type beadsmill method. To obtain Si-CNT nanocomposites with spherical morphologies, a silica precursor (tetraethylorthosilicate, TEOS) and polymer (PMMA) mixture was employed as a structure-directing medium. Thus the Si-CNT/Silica-Polymer microspheres were prepared by an acid catalyzed sol-gel method. Then a carbon precursor such as polypyrrole (PPy) was incorporated onto the surfaces of pre-existing Si-CNT/silica-polymer to generate Si-CNT/Silica-Polymer@PPy microspheres. Subsequent thermal treatment of the precursor followed by wet etching of silica produced Si-CNT@C microcapsules. The intermediate silica/polymer must disappear during the carbonization and etching process resulting in the formation of an internal free space. The carbon precursor polymer should transform to carbon shell to encapsulate remaining Si-CNT nanocomposites. Therefore, hollow carbon microcapsules containing Si-CNT nanocomposites could be obtained (Si-CNT@C). The successful fabrication was confirmed by scanning electron microscopy (SEM) and X-ray diffraction (XRD). These final materials were employed for anode performance improvement in lithium ion battery. The cyclic performances of these Si-CNT@C microcapsules were measured with a lithium battery half cell tests.     

Preparation and surface characterization of polymer nanoparticles designed for incorporation into hybrid materials

We prepared water dispersions of poly(n-butyl methacrylate-st-butyl acrylate) crosslinked core-shell nanoparticles functionalized with different amounts of trimethoxisilane (TMS) groups in the outer shell. The purpose of the TMS groups is to chemically bind the rubbery particles to a nanostructured silica network, using sol-gel copolymerization. Here, we present nanoparticles containing 13 mol % and 30 mol % of TMS groups in the outer shell and compare their surface morphology with particles that do not contain TMS. The particles are prepared by a two-step seeded emulsion polymerization technique at neutral pH. In the first step, we obtained crosslinked seed particles (44 nm in diameter) by a batch process. In the second step, we used a semi-continuous emulsion polymerization technique under starved feed conditions to obtain monodispersed particles of controlled composition and size (ca. 100 nm in diameter). Fluorescence decay measurements were performed in situ on the dispersions, using a pair of cationic dyes adsorbed onto the surface of the nanoparticles: rhodamine 6G as the energy transfer donor and malachite green carbinol hydrochloride as the acceptor. The kinetics of F?rster resonance energy transfer (FRET) between the dyes is sensitive to the donor-acceptor distance, allowing us to obtain the binding distribution of the dyes at the nanoparticle surface. For the unmodified nanoparticles, we found a dye distribution that corresponds to an average interface thickness of delta = (5.2 +/- 0.2) nm. For the samples containing 13 mol % and 30 mol % of TMS groups in the outer shell we obtained broader interfaces, with widths of delta = (6.2 +/- 0.2) nm and delta = (6.5 +/- 0.1) nm respectively. This broadening of the distribution with the surface modification is interpreted in terms of the increase in free volume of the shell caused by the TMS groups. Finally, we studied the effect of temperature on the water-polymer interface fuzziness, in order to evaluate the accessibility of the TMS groups during the sol-gel synthesis of nanostructured hybrid materials.     

Fabrication of monodisperse luminescent nanoparticles with core/shell poly(styrene/thiophene) structure

Luminescent poly(styrene/thiophene) (PSt/PT) core/shell nanoparticles were prepared by oxidative polymerization in the presence of PSt seed particles. PSt seed particles with uniform size distribution were prepared with an anionic surfactant by an emulsion polymerization process, and were used as a template to prepare monodispersive PT‐coated nanoparticles. A luminescent Polythiophene (PT) layer was formed on the surface of PSt nanoparticles by oxidation polymerization with iron chloride (FeCl₃) and hydrogen peroxide (H₂O₂). The mechanism of core/shell formation was found to be the interface‐dominant polymerization induced by the electrostatic attraction between the sulfonate group of anionic surfactant and Fe³⁺ ions after the diffusion of thiophene monomer to the PSt nanoparticles. Field‐emission scanning electron microscopy and transmission electron microscopy (TEM) proved the core/shell structure, which provided key evidence that PT was incorporated onto the surface of PSt nanoparticles. In addition, the effect of the PT shell thickness on photoluminescent (PL) intensity was investigated by changing the shell thickness of PSt/PT nanoparticles. We observed that the PL intensity increased up to about 30 nm of PT shell thickness, and then decreased due to self‐absorption. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 5968–5975, 2008