Chromatography of inorganic ions o sulfoethyl cellulose layer in hydrochloric acid and in hydrochloric acid-ammonium thiocyanate media

Summary Chromatographic behavior of 51 inorganic ions has been systematically studied on layers of sulfoethyl (SE) cellulose, a strongly acidic exchanger, in hydrochloric acid and in acid-ammonium thiocyanate media. The sorption of most of the ions on he SE-cellulose decreases with increasing concentration of the acid and the thiocyanate. The characteristic retention of some metal ions of SE-cellulose layer can be recognized over a low concentration of the acid or the salt. Feasibilities for separations of analytical interest are also presented in both systems.     

Thin-layer chromatography of a number of inorganic ions on sulfoethyl cellulose in acetic acid and in acetic acid-ammonium acetate media

Summary The thin-layer chromatographic behaviour of 51 inorganic ions has been studied on a strongly acidic cation exchanger, sulfoethyl cellulose, using acetic acid and acetic acid-ammonium acetate media. Feasibilities for effective separations of analytical interest are demonstrated on the cellulose layer (0.50mm thick) in both media.     

Chromatography of inorganic ions on sulfoethyl cellulose layer in mixed sulfuric acid-organic solvent media

Summary The thin-layer chromatographic behavior of 49 inorganic ions has been systematically studied on layers of sulfoethyl (SE) cellulose, a strongly acidic cation-exchanger, with binary solvent mixtures consisting of sulfuric acid and an organic solvent such as methanol or acetone. The characteristic retention on the cellulose layer can be recognized for some ions forming sulfato complexes in the acid-organic solvent medium, and some aspects of the behavior are discussed. Chromatographic separations of analytical interest are also demonstrated on the SE-cellulose layer with acid-methanol and acid-acetone solutions used as mobile phases.     

Development and validation of a cyclodextrin‐modified capillary electrophoresis method for the enantiomeric separation of vildagliptin enantiomers

The enantiomers of vildagliptin, an orally available and selective dipeptidyl‐peptidase‐4 inhibitor used for the treatment of type II diabetes, have been separated by CD‐modified CZE, using uncoated fused‐silica capillary. After screening 13 negatively charged CD derivatives as potential chiral selectors, sulfobutyl‐ether‐α‐CD (SBE‐α‐CD) was selected for the enantioseparation. For the optimization, a factorial analysis study was performed by orthogonal experimental design. Six experimental factors were chosen as variable parameters: temperature, applied voltage, chiral selector and BGE concentrations, pH, and the parameters of the hydrodynamic injection. The optimized system still was not considered final as the second peak (S‐enantiomer) migrated too close to the EOF, resulting in a potential inaccuracy during the determination of the chiral impurity. To fine‐tune the method “one factor at a time” variation approach was applied. The final method (applying 15°C capillary temperature, 40 mbar × 4 s hydrodynamic injection, 25 kV voltage in 75 mM acetate‐Tris buffer [pH 4.75] containing 20 mM SBE‐α‐CD as chiral selector) was validated according to the ICH guideline. RSD percentage of the resolution value, migration times, and corrected peak areas were below 5% during testing repeatability and intermediate precision. LOD and LOQ values were found to be 2.5 and 7.5 μg/mL, respectively. The method is considered linear in the 7.5–180 μg/mL range for the R‐enantiomer. The robustness of the method was justified using Plackett–Burmann statistical experimental design.     

Development and validation of a capillary electrophoresis method for the characterization of protegrin IB-367.

A capillary electrophoresis (CE) method was developed to characterize protegrin IB-367, an antimicrobial peptide being developed for the treatment of oral mucositis and for other topical applications. The electrophoretic purity and levels of potential impurities/degradation products of IB-367 drug substance are determined by CE using area normalization. Electrophoresis parameters were optimized to allow optimal resolution, reproducibility and minimal analysis time. The separation and resolution between this polycationic peptide and truncated analogs determined by the CE method was much greater than those by the HPLC methods. In addition, the CE methods separates the potential impurities/degradation products from each other while the HPLC methods failed to resolve them. The CE method was validated in the aspects of accuracy, precision, linearity, range, limit of detection, limit of quantitation, specificity, system suitability and robustness. An internal standard was used for the quantitation purpose. The selection criteria of the internal standard as well as the method validation results are presented. The truncated peptide analogs were used to demonstrate the specificity of the method. These analogs were also used to evaluate the limit of quantitation of potential impurities. The relative response factors of these analogs were assessed to determine area normalization feasibility. System suitability tests were established.     

Development of a capillary electrophoresis method for the characterization of "palo azul" (Eysenhardtia polystachya)

The tree Eysenhardtia polystachya (Ortega) Sarg. has quite a wide popular use within the traditional Mexican medicine as herbal remedy. Popular practices constitute a relevant enough basis to design optimum analytical methods in order to determine basic principles of diverse medicinal plants. This has become one of the essentials needed to characterize such products, for which it is fundamentally important to develop an efficient and reliable separation method. This work presents the results concerning the development and optimization of a novel CE method for the separation of components from water/etanol (1:1) extracts of E. polystachya, using the following conditions, considered the best obtained: phosphate buffer 10 mM, 20 kV voltage, and pH 8.1 at 214 nm and 50 mM, 12.5 kV voltage with pH 8.1 at 426 nm. The optimization takes into account the parameters associated in the resulting electropherograms, such as number of peaks, migration times, and the Deltat(m) of the neighboring peaks. Under optimal conditions the separation intended was attained within 15 and 20 min for 214 and 426 nm, respectively. The characterization method developed was applied to the analysis of diverse extracts of E. polystachya.     

Development and validation of a high-precision capillary electrophoresis method for main component assay of ragaglitazar

The ability of a developed capillary electrophoresis (CE) method for fast, efficient and reliable main component assay of ragaglitazar [NNC 61-0029/DRF(-)2725] has been demonstrated through documentation of the analytical performance and the results of a successful validation. The fast analysis time of around 1.2 min ensures a high analytical capacity, and the validation results show that the CE method is robust and gives reliable and precise results. The results from the validation of the CE method meet the acceptance criteria that are normally set for other main component assays such as high-performance liquid chromatography assays.     

Development of a capillary electrophoresis method for the characterization of collagens in cartilage tissue

The use of capillary electrophoresis (CE) for the separation of peptides specific to type I and type II collagen is evaluated. The aim of this work is to develop a method to characterize cartilage, cartilage repair tissue, and tissue engineered cartilage. The analysis is dependent on the cleavage of collagen into constituent peptides by cyanogen bromide. A number of these peptides are specific to the collagen type. CE is evaluated for the separation of these specific peptides using uncoated and coated capillaries over a wide range of pH and buffer concentrations. Separation of peptides specific to type I and type II collagen is achieved using a Supelco CElect N capillary and a 100mM phosphate buffer at pH 6. Meniscal cartilage is characterized using this method. The proportion of type I collagen to type II collagen corresponds well with that reported by others and indicates the potential of this method for the characterization of cartilage.     

Development and validation of a capillary zone electrophoresis method for the quantitative determination of anthocyanins in wine

A capillary zone electrophoresis (CZE) method is proposed for the quantitative determination of anthocyanins in wine as an alternative to high-performance liquid chromatography. The CZE separation was carried out using a 46 cm (effective length)×75 μm I.D. fused-silica capillary at 10 °C and a 50 mM sodium tetraborate buffer at pH 8.4 with 15% of methanol as modifier. A voltage of 25 kV and a hydrodynamic injection of 300 mbar s were used. The electropherograms were recorded at 599 nm. It was found that SO₂ (antibacterial and antioxidant agent added to wine during its production) increased the absorbance of anthocyanins at 599 nm in a basic medium. Therefore, a concentration of 250 mg/l of SO₂ was added to the samples and the calibration solution before the analysis in order to avoid errors by this matrix effect. The analytical response was linear (R=0.998) between 10 and 700 μg/ml of malvidin-3-O-glucoside. The limit of detection and the reproducibility (as a relative standard deviation, n=11) were 1 μg/ml and 1.5%, respectively. Finally, the CZE method was validated by the analysis of synthetic wine samples (errors less than 8%) and by the comparison of the results obtained in the analysis of different monovarietal wines by CZE with those obtained by the standard HPLC method. In this comparison, a good correlation (R=0.998) with a slope of 1.005±0.044 and an intercept of −0.752±6.690 was obtained for malvidin-3-O-glucoside.     

Development and validation of a capillary electrophoresis method applied to the analysis of l‐citrulline in an oral formulation for pediatric use

A simple and highly sensitive CE–UV method was applied in the determination of l ‐ctrulline, which was developed from an oral formulation for pediatric use. The novel method was based on the analysis of l ‐citrulline for direct ultraviolet detection at 198 nm. The BGE consisted of 10 mM sodium tetraborate and 50 mM SDS at pH 9, and the electrophoretic parameters were optimized. The method was validated in terms of specificity, linearity, LOD, LOQ, precision, accuracy, and robustness. The LOD and LOQ obtained were 1.36 and 4.54 μg/mL, respectively. In addition, the method offers higher sensitivity and specificity compared with the results obtained from HPLC method using UV‐detectors, in which l‐ citrulline needs to be derivatizated. Furthermore, low cost and simplicity of the system allowed the rapid and simple quantitation of l‐ citrulline in the oral formulation for quality control and stability indicated method.     

An environmentally friendly method for enzyme-assisted preparation of microfibrillated cellulose (MFC) nanofibers

Microfibrillated cellulose nanofibers (MFC) provide strong reinforcement in polymer nanocomposites. In the present study, cellulosic wood fiber pulps are treated by endoglucanases or acid hydrolysis in combination with mechanical shearing in order to disintegrate MFC from the wood fiber cell wall. After successful disintegration, the MFC nanofibers were studied by atomic force microscopy (AFM). Enzyme-treatment was found to facilitate disintegration, and the MFC nanofibers produced also showed higher average molar mass and larger aspect ratio than nanofibers resulting from acidic pretreatment.     

Development and validation of a chiral capillary electrophoresis method for assay and enantiomeric purity control of pramipexole

A rapid method for the enantioseparation of pramipexole and its R‐enantiomer has been developed by capillary electrophoresis. The influence of chemical and instrumental parameters was investigated including the type and concentration of chiral selectors, buffer composition and pH, co‐ions, applied voltage, capillary length and temperature. Optimal separation conditions were obtained using a 50 mM phosphate buffer (pH 2.8) containing 25 mM carboxymethyl‐β‐cyclodextrin on a fused‐silica capillary. Online UV detection was performed at 262 nm. A voltage of 25 kV was applied, and the capillary temperature was kept at 25°C. Hydrodynamic injection was performed at 3.45 kPa for 5.0 s. The separation of enantiomers was achieved in <6.5 min. The method was further validated in terms of stability of solutions, selectivity, linearity (both pramipexole and R‐enantiomer, R²>0.995), LOD and LOQ (0.91 and 2.94 μg/mL, respectively), repeatability (RSD<1.5%) and accuracy (pramipexole, 100.4%; R‐enantiomer, 100.5%). The proposed method was then applied to two kinds of pramipexole dihydrochloride monohydrate commercially available tablets, immediate release tablets (1.50 and 0.125 mg) and sustained release tablets (0.52 mg), to quantify the main component in the tablets. The amount of distomer could be quantified in bulk sample materials.     

Development and validation of a fast method for determination of free glycerol in biodiesel by capillary electrophoresis

In this study, a capillary electrophoresis (CE) methodology for the determination of free glycerol in biodiesel using oxidative cleavage with periodate was optimized and validated. The amount of iodate produced in the reaction was determined by CE. The optimized electrolyte was 20 mmol L(-1) glycine and 10 mmol L(-1) trifluoroacetic acid (direct UV detection, 210 nm). The short total analysis time (less than 28 s) was obtained using the short end injection mode. The optimization of the method was carried out using Peakmaster software. The choice of the components of the run electrolyte and of the internal standard (nitrate) was made through the use of effective mobility curves. A good correlation coefficient higher than 0.9991 and low LOD 4.3 mg L(-1) was obtained. The recovery of free glycerol was 95.4-102.4%. This method was used to determine glycerol in commercial biodiesel samples.     

Validated method for L-ornithine-L-aspartate analysis in human plasma by capillary electrophoresis

A rapid capillary electrophoresis method for routine determination of two amino acids, L-ornithine and L-aspartic acid, in human plasma is reported. The method runs automatically, requires a minimum of sample preparation and moreover includes no extensive extraction and no gradient or derivatization procedure. Analyses were performed on an uncoated silica capillary using buffer solution composed with 10 mM sodium tetraborate and 1 M sodium hydroxide (pH=10.0). A capillary electrophoresis P/ACE system equipped with UV detection (200 nm), an automatic injector, a fluid cooled cartridge and System Gold data station was used in this study. The total analysis time under these conditions was 8.0 min. The calibration curve was linear in the range 10-280 microg mL-1 for L-aspartic acid and 20-280 microg mL-1 for L-ornithine (for both amino acids, r=0.999). The method was validated by inaccuracy (bias) and precision (RSD) studies by analysing samples. The method was successfully applied to the quantitative determination of L-ornithine-L-aspartate in human plasma and could be useful for clinical and bioavailability investigations.     

Development and validation of capillary electrophoresis method for tobramycin with precapillary derivatization and UV detection

One of the major drawbacks in the analysis of aminoglycoside antibiotics is their lack of UV chromophore and/or fluorophore. Tobramycin, a representative member of this group, was examined in this study. To overcome the detection hurdle, a precapillary derivatization followed by capillary electrophoresis analysis with direct UV detection was investigated. A central composite design was applied to optimize the method and three parameters were selected in this study: buffer pH, temperature and % acetonitrile (ACN). Selectivity between tobramycin main component and its adjacent peaks as well as the peak efficiency and symmetry factors were established as responses. For each response, a model was obtained by a second-order mathematical expression. Successful results were obtained with a simple background electrolyte (BGE) containing 30 mM sodium tetraborate, pH 10.2, and ACN (75:25 v/v). Under these conditions, baseline separation of tobramycin from its adjacent kanamycin B and an unknown peak was achieved. A temperature of 20 degrees C and applied voltage of 28.0 kV were used. The method showed good validation data in terms of precision, limits of quantitation and detection, specificity and linearity and was found to be suitable for analysis of tobramycin bulk pharmaceutical samples.     

Development and validation of a novel sensitive UV‐direct capillary electrophoresis method for quantification of alendronate in release studies from biomaterials

A simple, highly sensitive, and robust CE method applied to the determination of alendronate (ALN) was developed from matrices for tissue engineering, characterized by being highly complex systems. The novel method was based on the ALN derivatization with o‐phthalaldehyde and 2‐mercaptoethanol for direct ultraviolet detection at 254 nm. The BGE consisted of 20 mM sodium borate buffer at pH 10, and the electrophoretic parameters were optimized.The method was validated in terms of specificity, linearity, LOD, LOQ, precision, accuracy, and robustness. The LOD and LOQ obtained were 0.8 and 2.7 μg/mL, respectively. In addition, the method offers higher sensitivity and specificity compared to other CE and HPLC methods using UV‐detectors, as well as low cost and simplicity that allowed the rapid and simple quantitation of ALN from bone regeneration matrices.     

Development and validation of a capillary electrophoresis method for the measurement of short-chain organic acids in natural rubber latex

Short-chain organic acid contents in serum of natural latex are interesting to measure and capillary electrophoresis (CE) has proved to be a good tool for their study. In the present work a method has been developed to identify the short-chain organic acids present in sera of natural rubber latex (oxalic, formic, fumaric, aconitic, succinic, malic, glutaric, citric, acetic, glycollic, propionic and quinic acids), the separation was optimised and the quantification method validated. The separation was performed on a CE system with UV detection at 200 nm. The separation was carried out with an uncoated fused-silica capillary (57 cm x 50 microm I.D.) and was operated at -10 kV potential. The separation buffers were prepared with 0.5 M H3PO4, 0.5 mM cetyltrimethylammonium bromide and pH adjusted by adding NaOH to 6.25 except for propionic acid which was better measured at pH 7.00. Validation parameters are adequate and limits of detection range from 0.005 mM to 1.6 mM. Short-chain organic acids were measured with this method in sera of three different types of latex.     

Development of a capillary zone electrophoresis method for caseinoglycomacropeptide determination

Caseinoglycomacropeptide (CGMP) is a polypeptide of 64 amino acid residues, derived from the C-terminal part of bovine κ-casein. A sensitive and selective capillary zone electrophoresis method has been developed and validated for the analysis and quantitation of CGMP. Separation is carried out at 30 kV, using an uncoated fused-silica capillary and 20 mM sodium citrate buffer at acidic pH 3.5. The described method allows the separation of various CGMP subcomponents. The validation data proves that the method has the requisite selectivity, sensitivity, reproducibility and linearity for CGMP assay and for quality control during CGMP manufacturing (batch-to-batch reproducibility).     

Development and validation of a capillary electrophoresis method for the determination of phenothiazines in human urine in the low nanogram per milliliter concentration range using field-amplified sample injection

A capillary zone electrophoresis (CZE) method with ultraviolet-visible detection has been established and validated for the determination of five phenothiazines: thiazinamium methylsulfate, promazine hydrochloride, chlorpromazine hydrochloride, thioridazine hydrochloride, and promethazine hydrochloride in human urine. Optimum separation was obtained on a 64.5 cm x 75 microm bubble cell capillary using a buffer containing 150 mM tris(hydroxymethyl)aminomethane and 25% acetonitrile at pH 8.2, with temperature and voltage of 25 degrees C and 20 kV, respectively. Naphazoline hydrochloride was used as an internal standard. Field-amplified sample injection (FASI) has been applied to improve the sensitivity of the detection. Considering the influence of parameters affecting the on-line preconcentration (nature of preinjection plug, sample solvent composition, injection times, and injection voltage) and due to the significant interactions among them, in this paper we propose for the first time the application of a multivariate approach to carry out the study. The optimized conditions were as follows: preinjection plug of water for 7 s at 50 mbar, electrokinetic injection for 40 s at 6.2 kV, and 32 microm of H3PO4 in the sample solvent. Also, a solid-phase extraction (SPE) procedure is developed to obtain low detection limits and an adequate selectivity for urine samples. The combination of SPE and FASI-CZE-UV allows adequate linearities and recoveries, low detection limits (from 2 to 5 ng/mL), and satisfactory precisions (3.0-7.2% for an intermediate RSD %).     

Multivariate optimisation and validation of a capillary electrophoresis method for the analysis of resveratrol in a nutraceutical

A rapid and simple method based on capillary electrophoresis was developed for the quality control of nutraceuticals containing resveratrol. Setting the UV detector at 280nm, the optimisation involved the separation of 11 effervescent tablet components, including the active compounds vitamin C, vitamin B(2), flavanones and hydroxycinnamic acids. Flufenamic acid was employed as internal standard. The effects of background electrolyte concentration, acetonitrile percentage and voltage were investigated by means of response surface methodology, considering as responses the critical resolution values and analysis time. The optimum conditions were found by Derringer desirability function. The background electrolyte consisted of 23mM borate buffer, adjusted to pH 10.0 with 1M sodium hydroxide, containing 7% (v/v) acetonitrile. Temperature and voltage were set at 25 degrees C and 26kV, respectively. Applying these conditions, the analysis time was below 7min. The performances of the method were tested in terms of selectivity, robustness, linearity and range, accuracy and precision and system suitability, following ICH guidelines.