On‐line determination of 4‐nitrophenol by combining molecularly imprinted solid‐phase extraction and fiber‐optic spectrophotometry

In the present paper, we describe a new on‐line SPE system where molecular imprinting, fiber‐optic detection and flow injection analysis were combined for the first time. This new system has been applied for the on line detection of 4‐nitrophenol (4‐NP). Initially, molecularly imprinted polymers (MIP) have been prepared for the selective extraction of 4‐NP using 4‐vinylpyridine and ethylene glycol dimethacrylate as functional and cross‐linking monomers, respectively. Selective extraction was achieved using the designed MIP with 97% of recovery on imprinted polymer and 10% on control polymer. The system provided a high degree of accuracy, with RSDs varying between 0.7 and 1.39%. In respect of accuracy, reproducibility, and rapidity, this system is comparable with HPLC. In short, the system allows simple, fast, and accurate analyte determination with the possibility of future automation.     

Urinary l‐kynurenine quantification and selective extraction through a molecularly imprinted solid‐phase extraction device

l ‐Kynurenine is an endogenous metabolite generated by the catabolic pathway of l ‐tryptophan and it could be a potential biomarker to test the efficacy of several checkpoint inhibitors that have already reached the clinical trials in the antitumor therapy. Thus, a molecularly imprinted polymer specific for the recognition of this metabolite was synthesized and used as innovative system in solid‐phase extraction technique for the specific extraction and quantification of l ‐kynurenine in human urine. The off‐line system was firstly tested on l ‐kynurenine standard solutions, allowing recoveries up to 97.7% (relative standard deviation = 2.2%) and then applied to fortified and deproteinated human urine samples, where a recovery of 84.1% (relative standard deviation = 3.1%) was obtained. The method was validated and it revealed a good linearity in the range of 0.157–20 μg/mL (r² = 0.9992). The optimized procedure demonstrated a good feasibility on biological samples, allowing a ready quantification of l ‐kynurenine in the human urine, where the metabolite was found at a very low concentration (0.80 μg/mL). The extraction system developed could attract attention of pharmaceutical industries for l ‐kynurenine production as potential drug in the treatment of autoimmune disorders through its extraction and purification from biological matrixes.     

Preparation and evaluation of a molecularly imprinted sol–gel material as the solid‐phase extraction adsorbents for the specific recognition of cloxacilloic acid in cloxacillin

Highly selective molecularly imprinted polymers on the surface of silica gels were prepared by a sol–gel process and used as solid‐phase extraction adsorbents for the specific recognition, enrichment and detection of cloxacilloic acid in cloxacillin. The obtained polymers were characterized by scanning electron microscopy, FTIR spectroscopy, nitrogen adsorption and desorption, elemental analysis and thermogravimetric analysis. The imprinted polymers not only possessed high adsorption capacity (6.5 μg/mg), but also exhibited fast adsorption kinetics (they adsorb 80% of the maximum amount within 20 min) and excellent selectivity (the imprinted factor was 3.6). A method using the imprinted polymers as solid‐phase extraction adsorbents coupled with high‐performance liquid chromatography was established with good specificity, linearity (r = 0.9962), precision (ranging from 0.5 to 6.7%), accuracy (ranging from 93.9 to 97.7%) and extraction recoveries (ranging from 78.8 to 89.8%). The limits of detection and quantification were 0.07 and 0.25 mg/g, respectively. This work could provide a promising method in the enrichment, extraction and detection of allergenic impurities in the manufacture, storage and application of cloxacillin.     

Determination of melamine in aquaculture feed samples based on molecularly imprinted solid‐phase extraction

This research highlights the application of highly efficient molecularly imprinted solid‐phase extraction for the preconcentration and analysis of melamine in aquaculture feed samples. Melamine‐imprinted polymers were synthesized employing methacrylic acid and ethylene glycol dimethacrylate as functional monomer and cross‐linker, respectively. The characteristics of obtained polymers were evaluated by scanning electron microscopy, Fourier transform infrared spectroscopy and binding experiments. The imprinted polymers showed an excellent adsorption ability for melamine and were applied as special solid‐phase extraction sorbents for the selective cleanup of melamine. An off‐line molecularly imprinted solid‐phase extraction procedure was developed for the separation and enrichment of melamine from aquaculture feed samples prior to high‐performance liquid chromatography analysis. Optimum molecularly imprinted solid‐phase extraction conditions led to recoveries of the target in spiked feed samples in the range 84.6–96.6% and the relative standard deviation less than 3.38% (n = 3). The aquaculture feed sample was determined, and there was no melamine found. The results showed that the molecularly imprinted solid‐phase extraction protocols permitted the sensitive, uncomplicated and inexpensive separation and pre‐treatment of melamine in aquaculture feed samples.     

Development of a selective sorbent for the solid‐phase extraction of terbuthylazine in olive oil samples: A molecular imprinting strategy

Aiming to implement an analytical methodology that is highly selective for the extraction and quantification of terbuthylazine from olive oil, we successfully achieved: (i) the development of a molecularly imprinted polymer by bulk polymerization using terbuthylazine as template molecule, methacrylic acid as functional monomer, ethylene glycol dimethacrylate as cross‐linker, and dichloromethane as porogen; (ii) characterization of the imprinting material using Fourier transform infrared spectroscopy, thermogravimetric analysis, nitrogen adsorption at 77 K, and scanning electron microscopy; (iii) their molecular recognition for the template molecule using high‐performance liquid chromatography, and (iv) optimization of a solid‐phase extraction procedure using as sorbent the synthesized molecularly imprinted polymer for the selective extraction and clean‐up of terbuthylazine from spiked organic olive oil and further quantification of the pesticide levels by high‐performance liquid chromatography. The suitability of the implemented analytical methodology was demonstrated, as concentrations of terbuthylazine below the tolerated maximum residue limits in the spiked organic olive oil samples could be satisfactorily analyzed with good precision/accuracy with high recovery rates (96%). Overall, the implemented methodology has proven to be reliable and robust and is highly promising in the field of sample preparation, particularly for the isolation/preconcentration of terbuthylazine in complex food samples.     

Preconcentration of indapamide from human urine using molecularly imprinted solid‐phase extraction

A simple, sensitive, and selective molecularly imprinted solid‐phase extraction and spectrophotometric method has been developed for the clean‐up and preconcentration of indapamide from human urine. Molecularly imprinted polymers were prepared by a non‐covalent imprinting approach using indapamide as a template molecule, 2‐(trifluoromethyl) acrylic acid as a functional monomer, ethylene glycol dimethacrylate as a crosslinker, N,N‐azobisisobutyronitrile as a thermal initiator and acetonitrile as a porogenic solvent. A non‐imprinted polymer was also prepared in the same way, but in the absence of template. Molecularly imprinted polymer and non‐imprinted polymer sorbents were dry‐packed into solid‐phase extraction cartridges. Eluates from cartridges were analyzed using a spectrophotometer for the determination of indapamide by referring to the calibration curve in the range 0.14–1.50 μg/mL. Preconcentration factor, limit of detection, and limit of quantification were 16.30, 0.025 μg/mL, and 0.075 μg/mL, respectively. A relatively high imprinting factor (9.3) was also achieved and recovery values for the indapamide spiked into human urine were in the range of 80.1–81.2%. In addition, relatively low within‐day (0.17–0.42%) and between‐day (1.1–1.4%) precision values were obtained as well. The proposed molecularly imprinted solid‐phase extraction and spectrophotometric method was successfully applied to selective extraction, preconcentration, and determination of indapamide from human urine samples.     

Preparation of novel curcumin‐imprinted polymers based on magnetic multi‐walled carbon nanotubes for the rapid extraction of curcumin from ginger powder and kiwi fruit root

A novel molecularly imprinted polymer based on magnetic phenyl‐modified multi‐walled carbon nanotubes was synthesized using curcumin as the template molecule, methacrylic acid as the functional monomer and ethylene glycol dimethacrylate as the cross‐linker. The phenyl groups contained in the magnetic imprinted polymers acted as the assisting functional monomer. The magnetic imprinted polymers were characterized by scanning electron microscopy, Fourier‐transform infrared spectroscopy and vibrating sample magnetometry. Adsorption studies demonstrated that the magnetic imprinted polymers possessed excellent selectivity toward curcumin with a maximum capacity of 16.80 mg/g. Combining magnetic extraction and high‐performance liquid chromatography technology, the magnetic imprinted polymer based on magnetic phenyl‐modified multi‐walled carbon nanotubes was applied for the rapid separation and enrichment of curcumin from ginger powder and kiwi fruit root successfully.     

Preparation of doxycycline‐imprinted magnetic microspheres by inverse‐emulsion suspension polymerization for magnetic dispersion extraction of tetracyclines from milk samples

A magnetic dispersion extraction method was developed based on a molecularly imprinted magnetic microsphere (MIMM) for the selective clean‐up and enrichment of tetracycline antibiotics from milk samples. The MIMMs were prepared by inverse‐emulsion suspension polymerization, using doxycycline, trimethylolpropane trimethacrylate, acrylamide, methacrylic acid, and surface‐modified Fe₃O₄ as a template molecule, crosslinker, functional monomer, and magnetic component, respectively. Synthesis and extraction conditions were optimized for obtaining excellent affinity and high selectivity. The magnetism, covering amount, and selectivity of the magnetic microspheres were characterized by a vibrating sample magnetometer, thermogravimetric analysis, and a competitive recognition experiment. The MIMMs were applied to separate tetracycline antibiotics from milk samples by magnetic dispersion extraction, and an enrichment factor of 9.28 and a good sample clean‐up were obtained. The average recoveries of four tetracycline antibiotics were obtained in the range of 74.5–93.8% with a precision of 1.2–5.2%. The LODs and LOQs of the proposed method were in the range of 7.4–19.4 and 24.7–64.7 μg/kg, respectively. The results indicated that magnetic dispersion extraction using MIMMs is a powerful tool for food‐sample pretreatment with high selectivity and a simplified procedure.     

Preparation of a stoichiometric molecularly imprinted polymer for auramine O and application in solid‐phase extraction

We describe a stoichiometric approach to the synthesis of molecularly imprinted polymers specific for auramine O. Using the stoichiometric interaction in molecular imprinting, no excess of binding sites is necessary and binding sites are only located inside the imprinted cavities. The free base of the template was obtained to facilitate the interaction with the monomers. Itaconic acid was selected as the functional monomer, and stoichiometric ratio of the interaction with the free base was investigated. The molecularly imprinted polymer preparation conditions such as cross‐linker, molar ratio, porogen were optimized as divinylbenzene, 1:2:20 and chloroform/N,N‐dimethylformamide, respectively. Under the optimum conditions, a good imprinting effect and very high selectivity were achieved. A solid‐phase extraction method was developed using the molecularly imprinted polymers as a sorbent and extraction procedure was optimized. The solid‐phase extraction method showed a high extraction recovery for auramine O in its hydrochloride form and free form compared to its analogues. The results strongly indicated that stoichiometric imprinting is an efficient method for development of high selectivity molecularly imprinted polymers for auramine O.     

Molecularly imprinted solid‐phase extraction coupled with ultra high performance liquid chromatography and fluorescence detection for the determination of estrogens and their metabolites in wastewater

Estrogens are an important class of endocrine‐disrupting compounds, and their contamination of environmental waters through the effluents of wastewater treatment plants could have an important impact on aquatic biota, even at low concentrations. For this reason, the development of selective and sensitive extraction methodologies, which permit the identification and quantification of these compounds at trace level concentrations, is very important. In this study, a quantitative method based on molecularly imprinted solid phase extraction coupled to ultra high performance liquid chromatography with fluorescence detection has been developed. It has been used for the simultaneous determination of three estrogens and two of their metabolites in water samples from wastewater treatment plants. The method developed presents satisfactory limits of detection (between 0.18 and 0.45 ng·mL^?1), good recoveries (higher than 60%) and low relative standard deviations (under 10%). The method was used to analyze wastewater from a veterinary hospital as well as influent and effluent samples of a wastewater treatment plant of Gran Canaria (Spain) The concentrations of the detected hormones ranged from 1.35 to 2.57 ng·mL^?1.     

Preparation of a novel molecularly imprinted polymer for the highly selective extraction of baicalin

The selective extraction of baicalin is important to its quality control especially when the matrices are complicated. In this work, a novel molecularly imprinted polymer was prepared for the selective extraction of baicalin in herbs. The molecularly imprinted polymer was synthesized by the copolymerization of 4‐vinyl pyridine and ethylene glycol dimethacrylate in the presence of baicalin by a precipitation polymerization method. After the optimization of parameters for molecularly imprinted polymer preparation, including the functional monomer, porogen, sampling solvent, and washing solvent, good selectivity was obtained, with an imprinting factor of about 4, which is much better than that achieved by the bulk‐polymerization method. The performances of the prepared molecularly imprinted polymers were systematically investigated, including adsorption kinetics, isotherm experiment, and Scatchard analysis. On the basis of the good adsorptive capability of the prepared molecularly imprinted polymer, it was also applied for the pretreatment of baicalin in Scutellaria baicalensis Georgi. The result showed that most of the matrices were removed and baicalin was selectively enriched.     

Molecularly imprinted polymers for the solid‐phase extraction of four fluoroquilones from milk and lake water samples

A method based on molecular crowding and ionic liquids as reaction solvents has been used for the synthesis of molecularly imprinted polymers. Levofloxacin was selected as the template, polymethyl methacrylate was the molecular crowding agent, and 1‐butyl‐3‐methylimidazolium tetrafluoroborate (ionic liquid) was selected as the reaction solvent and porogen. The optimized proportion for the mixed porogen was dimethyl sulfoxide/ionic liquid/polymethyl methacrylate 1:1.6:5 in chloroform (150 mg mL^?1). The morphology and chemical composition of levofloxacin imprinted polymers were assessed by scanning electron microscopy and Fourier transform infrared spectroscopy. The absorption experiments demonstrated that the levofloxacin imprinted polymers possess high selective recognition property to levofloxacin and analogs, including enrofloxacin, ciprofloxacin and gatifloxacin, which all belong to fluoroquinolones. An extraction method using levofloxacin imprinted polymers as sorbent followed by high‐performance liquid chromatography analysis was optimized for the determination of four fluoroquinolones in milk and lake water samples. Under the optimized conditions, good linearity was observed in a range of 5–1000 ng g^?1 with the limit of detection between 0.3 and 0.5 ng g^?1 for the four fluoroquinolones. The recoveries at three spiked levels ranged 82.4–98.3% with the relative standard deviation ≤4.9.     

Preparation of molecularly imprinted polymers for strychnine by precipitation polymerization and multistep swelling and polymerization and their application for the selective extraction of strychnine from nux‐vomica extract powder

Monodisperse molecularly imprinted polymers for strychnine were prepared by precipitation polymerization and multistep swelling and polymerization, respectively. In precipitation polymerization, methacrylic acid and divinylbenzene were used as a functional monomer and crosslinker, respectively, while in multistep swelling and polymerization, methacrylic acid and ethylene glycol dimethacrylate were used as a functional monomer and crosslinker, respectively. The retention and molecular recognition properties of the molecularly imprinted polymers prepared by both methods for strychnine were evaluated using a mixture of sodium phosphate buffer and acetonitrile as a mobile phase by liquid chromatography. In addition to shape recognition, ionic and hydrophobic interactions could affect the retention of strychnine in low acetonitrile content. Furthermore, molecularly imprinted polymers prepared by both methods could selectively recognize strychnine among solutes tested. The retention factors and imprinting factors of strychnine on the molecularly imprinted polymer prepared by precipitation polymerization were 220 and 58, respectively, using 20 mM sodium phosphate buffer (pH 6.0)/acetonitrile (50:50, v/v) as a mobile phase, and those on the molecularly imprinted polymer prepared by multistep swelling and polymerization were 73 and 4.5. These results indicate that precipitation polymerization is suitable for the preparation of a molecularly imprinted polymer for strychnine. Furthermore, the molecularly imprinted polymer could be successfully applied for selective extraction of strychnine in nux‐vomica extract powder.     

Preparation and selective recognition of a novel solid‐phase microextraction fiber combined with molecularly imprinted polymers for the extraction of parabens in soy sample

A prepared molecularly imprinted polymer with ethyl p‐hydroxybenzoate as template molecule was applied for the first time to a homemade solid‐phase microextraction fiber. The molecularly imprinted polymer‐coated solid‐phase microextraction fiber was characterized by scanning electron microscopy and thermogravimetric analysis. Various parameters were investigated, including extraction temperature, extraction time, and desorption time. Under the optimum extraction conditions, the molecularly imprinted polymer‐coated solid‐phase microextraction fiber exhibited higher selectivity with greater extraction capacity toward parabens compared with the nonimprinted polymer‐coated solid‐phase microextraction fiber and commercial fibers. The molecularly imprinted polymer‐coated solid‐phase microextraction fiber was tested using gas chromatography to determine parabens, including methyl p‐hydroxybenzoate, ethyl p‐hydroxybenzoate, and propyl p‐hydroxybenzoate. The linear ranges were 0.01–10 μg/mL with a correlation coefficient above 0.9943. The detection limits (under signal‐to‐noise ratio of 3) were below 0.30 μg/L. The fiber was successfully applied to the simultaneous analysis of three parabens in spiked soy samples with satisfactory recoveries of 95.48, 97.86, and 92.17%, respectively. The relative standard deviations (n=6) were within 2.83–3.91%. The proposed molecularly imprinted polymer‐coated solid‐phase microextraction method is suitable for selective extraction and determination of trace parabens in food samples.     

Development of a molecularly imprinted solid‐phase extraction sorbent for the selective extraction of telmisartan from human urine

A novel molecularly imprinted solid‐phase extraction with spectrofluorimetry method has been developed for the selective extraction of telmisartan from human urine. Molecularly imprinted polymers were prepared by a noncovalent imprinting approach through UV‐radical polymerization using telmisartan as a template molecule, 2‐dimethylamino ethyl methacrylate as a functional monomer, ethylene glycol dimethacrylate as a cross‐linker, N,N‐azobisisobutyronitrile as an initiator, chloroform as a porogen. Molecularly imprinted polymers and nonimprinted control polymer sorbents were dry‐packed into solid‐phase extraction cartridges, and eluates from cartridges were analyzed using a spectrofluorimeter. Limit of detection and limit of quantitation values were 11.0 and 36.0 ng/mL, respectively. A very high imprinting factor (16.1) was achieved and recovery values for the telmisartan spiked in human urine were in the range of 76.1–79.1%. In addition, relatively low within‐day (0.14–1.6%) and between‐day (0.11–1.31%) precision values were obtained. Valsartan was used to evaluate the selectivity of sorbent as well. As a result, a sensitive, selective, and simple molecularly imprinted solid‐phase extraction with spectrofluorimetry method has been developed and successfully applied to the direct determination telmisartan in human urine.     

Solid‐phase extraction based on a molecularly imprinted polymer for the selective determination of four benzophenones in tap and river water

This work reports the preparation of molecularly imprinted polymer particles for the selective extraction and determination of four benzophenones from aqueous media. The polymer was prepared by using 4‐vinylpridine as functional monomer, ethylene glycol dimethacrylate as cross‐linker, acetonitrile as porogenic solvent and 2,2’,4,4’‐tetrehydroxybenzophenone as template. Good specific adsorption capacity (Q_max = 27.90 μmol/g) for 2,2’,4,4’‐tetrehydroxybenzophenone was obtained in the sorption experiment and good class selectivity for 2,2’,4,4’‐tetrehydroxybenzophenone, 2,4‐dihydroxybenzophenone, 2,2’‐dihydroxy‐4‐methoxybenzophenone, 2,2’‐dehydroxy‐4,4’‐dimethoxybenzophenone was demonstrated by the chromatographic evaluation experiment. Factors affecting the extraction efficiency of the molecularly imprinted solid‐phase extraction procedure were investigated systematically. An accurate and sensitive analytical method based on the molecularly imprinted solid‐phase extraction coupled with high‐performance liquid chromatography and diode array detection has been successfully developed for the simultaneous determination of four benzophenones from tap water and river water with method detection limits of 0.25–0.72 ng/mL. The recoveries of benzophenones for water samples at two spiking levels (500 and 5000 ng/mL for each benzophenone) were in the range of 86.9–103.3% with relative standard deviations (n = 3) below 9.2%.     

The use of molecularly imprinted polymers for the multicomponent determination of endocrine‐disrupting compounds in water and sediment

The method employing molecularly imprinted polymers for the extraction and clean up of endocrine‐disrupting compounds (estrogens, bisphenol A, and alkylphenols) from water and sediment is described. The identical extraction/clean‐up and LC‐MS/MS condition were used for the analysis of both types of samples. The method showed high recoveries ranging from 90 to 99% with excellent precision (intrabatch: 3.6–9.3%; interbatch: 5.6–11.4% for water; intrabatch: 4.3–8.5%; interbatch: 6.1–9.6% for sediment). The LOD was in the range of 0.7–1.9 ng/L and 0.3–0.6 ng/g for water and sediment, respectively. Overall extraction on molecularly imprinted polymers substantially enhanced sample clean‐up. The difference in efficiency of clean‐up was particularly pronounced when a large sample volume/weight was extracted and analyzed. Finally, the method was successfully applied for the analysis of 20 water and sediment samples.     

马拉硫磷分子印迹聚合物的制备及其在固相萃取中的应用

以马拉硫磷为模板分子,采用原位逐步聚合法制备了具有良好识别性能的分子印迹聚合物(MIPs),考察了马拉硫磷、甲基对硫磷、对硫磷及甲胺磷在马拉硫磷聚合物的选择性分离富集特性。用聚合物固相萃取了蜂蜜、蔬菜和天然水中的马拉硫磷。结果表明,聚合物对模板分子产生了印迹效应,对马拉硫磷有明显的选择性。流速为1.0 mL/min,进...     

Preparation of 17β‐estradiol‐imprinted material by surface‐initiated atom transfer radical polymerization and its application

A novel 17β‐estradiol molecularly imprinted polymer was grafted onto the surface of initiator‐immobilized silica by surface‐initiated atom transfer radical polymerization. The resulting molecularly imprinted polymer was characterized by elemental analysis and thermogravimetric analysis. The binding property of molecularly imprinted polymer for 17β‐estradiol was also studied with both static and dynamic methods. The results showed that the molecularly imprinted polymer possessed excellent recognition capacity for 17β‐estradiol (180.65 mg/g at 298 K), and also exhibited outstanding selectivity for 17β‐estradiol over the other competitive compounds (such as testosterone and progesterone). Then, the determination of trace 17β‐estradiol in beef samples was successfully developed by using molecularly imprinted polymer solid‐phase extraction coupled with high‐performance liquid chromatography. The limit of detection was 0.25 ng/mL, and the amount of 17β‐estradiol in beef samples was detected at 2.83 ng/g. This work proposed a sensitive, rapid, reliable, and convenient approach for the determination of trace 17β‐estradiol in complicated beef samples.     

Preparation and application of hollow molecularly imprinted polymers with a super‐high selectivity to the template protein

Protein‐imprinted polymers with hollow cores that have a super‐high imprinting factor were prepared by etching the core of the surface‐imprinted polymers that used silica particles as the support. Lysozyme as template was modified onto the surface of silica particles by a covalent method, and after polymerization and the removal of template molecules, channels through the polymer layer were formed, which allowed a single‐protein molecule to come into the hollow core and attach to the binding sites inside the polymer layer. The adsorption experiments demonstrated that the hollow imprinted polymers had an extremely high binding capacity and selectivity, and thus a super‐high imprinting factor was obtained. The as‐prepared imprinted polymers were used to separate the template lysozyme from egg white successfully, indicating its high selectivity and potential application in the field of separation of protein from real samples.