N 掺杂TiO2光催化剂的制备及其可见光活性研究

A visible-light-active photocatalyst was prepared by calcination of the hydrolysis product of tetrabutyl titanate with ammonia as precipitant. The photocatalyst was characterized by X-ray diffraction (XRD), UV-Vis diffuse reflection spectra (DRS), thermal gravimetric-differential thermal analysis (TG-DTA), X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM). The color of the photocatalyst was yellow and could absorb light wavelength under 550 nm as measured by DRS. The catalyst calcined at higher temperature will give lower absorbance for visible light. Structures of the sample were characterized mainly to be anatase by XRD except for the sample calcined at 700 ℃ which gave mixtures of anatase and rutile. TG-DTA results showed that temperature for anatase formation was 415 ℃. XPS results showed that doped-nitrogen was presented in the sample, they are important to show visible-light absorbency. The photocatalytic activities were evaluated using methyl orange and phenol as model pollutants, the results showed that over 90% of phenol could be degraded under visible light using N/TiO₂ as the catalyst after 4 hours reaction. Almost the same activity was found for the TiO₂ photocatalyst calcined at different temperature under sunlight but activities were different when the treatment was under UV light.     

金纳米粒子在TiO2气凝胶基质上的行为: 光催化活性评价和结构研究

TiO2 -Au aerogels containing different amounts of gold nanoparticles of different sizes (5 and 16 nm) were successfully synthesized using a sol-gel procedure, and were tested for salicylic acid photodegradation under UV irradiation. The structure and morphology of the obtained materials were investigated using X-ray diffraction, transmission electron microscopy, and N2 adsorption-desorption measurements. UV-Vis spectroscopy was used to study the optical properties. The effects of the gold nanoparticles on the TiO2 crystallization process were twofold, as follows: (i) the number of crystallized zones was strongly related to the concentration of the gold nanoparticles, and (ii) the smaller gold particles increased the time taken for the crystallization of the samples. It was found that the noble metal-doped samples exhibited higher degradation rates compared with bare titania. It was found that the most active photocatalyst in each studied system was the sample with the highest concentration of gold nanoparticles. Additionally, the highest degradation rate value was obtained with the smallest Au nanoparticles (46.4 10-3 μmol/(L·s).     

介孔InVO4光催化剂的合成及其光催化分解水的性能

 The mesoporous photocatalyst InVO4 was synthesized by the template-directing self-assembling method. The synthesized InVO4 was characterized by means of X-ray diffraction, transmission electron microscopy, N2 adsorption, and ultraviolet-visible spectroscopy. The results showed that the crystal structure of InVO4 could be controlled by changing the calcination temperature. Compared with the anatase TiO2 and conventional InVO4, the mesoporous InVO4 was more responsive toward visible light. The evolution rate of H2 from water over the mesoporous InVO4 achieved 1836 μmol/(g·h) under UV light irradiation, which was much higher than the anatase TiO2 and conventional InVO4.     

Preparation and characterization of In and Cu co-doped ZnS photocatalysts for hydrogen production under visible light irradiation

In this work, a new photocatalyts In(0.1),Cu(x)-Zn S(x = 0.01, 0.03, 0.05) is successfully synthesized using simple hydrothermal method. The physical and chemical properties of the In and Cu co-doped Zn S photocatalyst were characterized by X-ray diffraction(XRD), field emission scanning electron microscopy(FESEM), diffuse reflectance UV-visible spectroscopy(DR UV-visible) and photoluminescence spectroscopy(PL). The photocatalytic activity of the as-prepared In and Cu co-doped Zn S for hydrogen production from water with Na_2SO_3 and Na_2S as sacrificial agent under visible light irradiation(λ≥ 425 nm) was investigated. The presence of co-dopants facilitated the separation of electron-hole as well as increases the visible light absorption. The absorption edge of the co-doped Zn S photocatalyst shifted to longer wavelength as the amount of Cu increases. This indicates that the absorption properties depended on the amount of Cu doped. The photocatalytic activity of single doped In(0.1)-Zn S was significantly enhanced by co-doping with Cu under visible light irradiation. The highest photocatalytic activity was observed on In(0.1),Cu(0.03)-Zn S with the hydrogen production rate of 131.32 μmol/h under visible light irradiation.This is almost 8 times higher than single doped In(0.1)-Zn S.     

Influence and Characterization of Acidity on Fine Silicon Powder Immobilized Photocatalyst

TiO2 photocatalyst was supported with tetrabutyl titanate sol as precursor and fine silicon powder obtained from ferroalloys factory as carder to discuss the influence of pH value of gel precursor on microstructure and activity of photocatalyst in the process of synthesizing nano-TiO2 by using sol-gel method, the purpose of which is to provide fundamental data for the recycle of photocatalytic material. Under the irradiation of ultraviolet light, the photocatalytic degradation rate of methyl orange solution was used to characterize the photocatalytic activity of the sample. The specific surface area of the sample was tested by N2 desorption method, crystal form of TiO2 was analyzed by X-ray powder diffraction, and the microtopography of the sample was observed by scanning electron microscopy. The experimental results showed that the acidity of gel precursor could greatly affect the specific surface area and photocatalytic activity of the photocatalyst, and the optimum pH value of the precursor was determined as 2.0, and at this time the specific surface area of photocatalyst could reach 34.0 m^2/g. In the sample, the proporticn of anatase to rutile is 7：3, which makes l0 mg·L^-1 methyl orange solution fade after irradiation by 15W ultraviolet light for 24 h, and the degradation rate might be up to 98.1%.     

Gas-phase photocatalytic oxidation of benzene over titanium dioxide loaded on Bi_(12)TiO_(20)

TiO2 was prepared by sol-gel method using tetrabutyl titanate as precursor. TiO2 was loaded on Bi12TiO20. The photocatalyst with different TiO2 loading was calcined at 723 K. The photocatalytic activity of decomposition gaseous benzene was investigated in a batch reactor. The prepared photocatalyst was characterized by UV-vis diffuse reflectance. The result showed that TiO2/Bi12TiO20 absorbed much more ultraviolet light than Ti02 in the ultraviolet light region and showed red shift. The results indicated that the prepared photocatalyst can greatly promote the photocatalytic activity. The 2.0% TiO2/Bi12TiO20 system exhibited the highest photocatalytic activity.     

水热法合成多孔Ag_2S敏化二氧化钛催化剂及其可见光催化活性(英文)

Porous Ag2S sensitized TiO2 catalysts were synthesized by the hydrothermal process.The crystallization and porous structure of the Ag2S/TiO2 composite photocatalysts were investigated by X-ray diffraction,scanning electron microscopy with energy dispersive X-ray analysis,UV-Vis diffuse reflectance spectroscopy,and N2 adsorption.The Ag2S/TiO2 composites were mainly composed of anatase TiO2 and acanthite Ag2S.The absorption edge wavelengths of TiO2 and the Ag2S/TiO2 composite prepared with 3 mmol Na2S.5H2O were 400 and 800 nm,respectively,that is,the absorption edge of the composite had a pronounced red shift.The photocatalytic activity under visible light was investigated by the degradation of methylene blue with a UV-Vis spectrophotometer.The photocatalytic activities under visible light of the Ag2S/TiO2 photocatalysts were much higher than that of TiO2.     

Characterization of TiO2 Loaded on Activated Carbon Fibers and Its Photocatalytic Reactivity

In this paper, TiO2 loaded on activated carbon fibers （ACF） was prepared by a coating treatment, followed by calcination at different temperatures in air atmosphere. The photocatalyst developed was characterized by SEM, XRD, XPS and UV-Vis adsorption spectroscopy. It was observed from SEM images that TiO2 loaded on ACF was in the form of small clusters with nanometer size. As confirmed by XRD and XPS determinations, the crystalline pattern of immobilized TiO2 was still anatase-form after calcination, and the micrographic structure and surface properties of ACF have not been damaged by the deposition process and calcination at different temperatures. Photocatalytic degradation of methylene blue （MB） in aqueous .solution was investigated using TiOE/ACF as photocatalyst. The comparison of photolysis, absorption and photocatalysis was carded out. The results indicated that the photocatalysis process of combined photocatalyst showed much higher degradation rate than that of photolysis and absorption processes. In addition, the possibility of cyclic usage of the photocatalyst was also confirmed.     

铂沉积对Ga2O3-SiO2纳米粒子光催化性能的提高（英文）

Ga2O3‐SiO2 nanoparticles were prepared by a sol‐gel method and Pt was then immobilized on their surface via photo‐assisted deposition (PAD). The produced samples were characterized using X‐ray diffraction (XRD), ultraviolet and visible spectroscopy, photoluminescence emission spectroscopy, and surface area measurements. The catalytic performances of the Ga2O3‐SiO2 and Pt/ Ga2O3‐SiO2 samples were evaluated for the degradation of cyanide using visible light. XRD and EDX results showed that the Pt was well dispersed within the Ga2O3‐SiO2 phase and was detected on the surface of the catalyst, which confirmed the successful loading of Pt ions by the PAD method. BET results revealed that the surface area of Ga2O3‐SiO2 was higher than that of Pt/Ga2O3‐SiO2 . 0.3 wt% Pt/Ga2O3‐SiO2 exhibited the highest photocatalytic activity for degradation of cyanide under visible light. The catalyst could be reused with no loss in activity for the first 10 cycles.     

可见光下具有高光子效应和光催化活性的CuS-石墨烯氧化物/TiO2复合材料的制备（英文）

CuS-graphene oxide/TiO2 composites were prepared using a sol-gel method to improve the photocatalytic performance of the photocatalyst. The composites were characterized by X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray analysis, and transmission electron microscopy. The photocatalytic activities were examined by the degradation of methylene blue (MB) under visible-light irradiation. The photodegradation of MB under visible-light irradiation reached 90.1% after 120 min. The kinetics of MB degradation was plotted alongside the values calculated from the Langmuir-Hinshelwood equation. The CuS-graphene oxide/TiO2 sample prepared using 0.2 mol of TiO2 showed the best photocatalytic activity. This was attributed to a cooperative reaction as a result of increased photoabsorption by graphene oxide and an increased photocatalytic effect by CuS.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.