Defect formation and transport in mixed-conducting La0.90Sr0.10Al0.85−xFexMg0.15O3−δ

The redox behavior of perovskite-type La_0.90Sr_0.10Al_0.85−xFe_xMg_0.15O_3−δ (x=0.20-0.40) mixed conductors was analyzed by the Mössbauer spectroscopy and measurements of the total conductivity and Seebeck coefficient in the oxygen partial pressure range from 10⁻²⁰ to 0.5 atm at 1023-1223 K. The results combined with oxygen-ion transference numbers determined by the faradaic efficiency technique in air, were used to calculate defect concentrations, mobilities, and partial ionic and p- and n-type electronic conductivities as a function of oxygen pressure. The redox and transport processes can be adequately described in terms of oxygen intercalation and iron disproportionation reactions, with the thermodynamic functions independent of defect concentrations. No essential delocalization of the electronic charge carriers was found. The oxygen non-stoichiometry values estimated from the conductivity vs. p(O₂) dependencies, coincide with those evaluated from the Mössbauer spectra.     

Mössbauer spectroscopy as a probe of magnetic states in La0.5Ca0.5FeO3−δ perovskite

Charge disproportionation in La_0.5Ca_0.5FeO_3−δ perovskite has been detected by zero-field Mössbauer spectra from 20 K to room temperature. On the basis of the parameters of center shifts and hyperfine fields, Mössbauer spectra identified that the iron ionic states are Fe³⁺ and Fe⁵⁺ below 150 K, Fe³⁺, Fe⁴⁺ and Fe⁵⁺ in the intermediate temperature region, as well as Fe³⁺ and Fe⁴⁺ above 220 K. At low temperatures, the system exhibits a cluster-glass-like state resulting from competition between antiferromagnetic interaction of Fe³⁺–Fe³⁺ and ferromagnetic interaction of Fe³⁺–Fe⁵⁺.     

Temperature-dependent Mössbauer and dielectric studies of Mg0.95Mn0.05Fe1.0Ti1.0O4

The effect of tetravalent Ti⁺⁴ substitution in Mg_0.95Mn_0.05Fe₂O₄ on its magnetic and electrical properties has been studied using X-ray diffraction, Mössbauer spectroscopy, isothermal dc magnetization and dielectric measurements. X-ray diffraction studies have shown the structural transformation from cubic to tetragonal with the Ti⁺⁴ substitution. The Mössbauer spectra of Mg_0.95Mn_0.05Fe_1.0Ti_1.0O₄ recorded in the temperature range 20-300 K shows the presence of the magnetic as well as quadrupole interactions. The isothermal hysteresis loop infers that the system exhibits a ferrimagnetic ordering at room temperature. The Zero-field-cooled (ZFC) and field-cooled (FC) magnetization studies support ferrimagnetic ordering of Mg_0.95Mn_0.05Fe_1.0Ti_1.0O₄ at room temperature. Signatures of ferroelectric transition have been observed in the temperature range 200-300 K from dielectric measurements. The observed magnetic and dielectric behaviour indicate that this material exhibits multiferroic behaviour.     

Structure and magnetic properties of (Nd,Dy)16(Fe,Co)76−xTixB8 powders prepared by mechanical alloying

Nanocrystalline (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ magnets were prepared by mechanical alloying and respective heat treatment at 973–1073 K/30–60 min. An addition of 0.5 at % of Ti results in an increase of coercivity from 796 to 1115 kA m⁻¹. Partial substitution of Nd by Dy results in an additional increase of coercivity up to 1234 kA m⁻¹. Mössbauer investigations shows that for x?1 the (Nd,Dy)₁₆(Fe,Co)_76−xTi_xB₈ powders are single phase. For higher Ti contents (x>1) the mechanically alloyed powders heat treated at 973 K are no more single phase, and the coercivity decreases due to the presence of an amorphous phase. A heat treatment at a higher temperature (1073 K) for longer time (1 h) results in the full recrystallisation of powders. The mean hyperfine field of the Nd₂Fe₁₄B phase decreases for titanium contents of 0?x?1, and remains constant for x>1. This indicates that the Ti content in the Nd₂Fe₁₄B phase reaches its maximum value.     

The role of iron in the formation of the magnetic structure and related properties of La0.8Sr0.2Co1−xFexO3 (x=0.15, 0.2, 0.3)

La_0.8Sr_0.2Co_1−xFe_xO₃ (x=0.15, 0.2, 0.3) samples were studied by means of AC magnetic susceptibility, magnetization, magnetoresistance and ⁵⁷Fe Mössbauer spectrometry. Iron was found to take on a high spin 3d^5−α electronic state in each of the samples, where α refers to a partly delocalized 3d electron. The compounds were found to exhibit a spin-cluster glass transition with a common transition temperature of ∼53 K. The spin-cluster glass transition is visualized in the ⁵⁷Fe Mössbauer spectra as the slowing down of magnetic relaxation below ∼70 K, thereby showing that iron takes part in the formation of the glassy magnetic phase. The paramagnetic-like phase found at higher temperatures is identified below T_c≈195 K as being composed of weakly interacting, magnetically ordered nanosized clusters of magnetic ions in part with a magnetic moment oriented opposite to the net magnetic moment of the cluster. For each of the samples a considerable low-temperature negative magnetoresistance was found, whose magnitude in the studied range decreases with increasing iron concentration. The observed results obtained on the present compounds are qualitatively explained assuming that the absolute strengths of magnetic exchange interactions are subject to the relation ∣J_Co–Co∣<∣J_Fe–Co∣<∣J_Fe–Fe∣.     

Ferromagnetic-to-antiferromagnetic transition in (Hf1−xTix)Fe2 intermetallic compounds induced by geometrical frustration of the Fe(2a) sites

The ferromagnetic-to-antiferromagnetic transition in the hexagonal (Hf_1−xTi_x)Fe₂ (0?x?1) intermetallic compounds has been investigated by ⁵⁷Fe Mössbauer spectroscopy. At 10 K, the transition occurs within rather narrow concentration limits, around x=0.55–0.65. We found that the key factor governing the unexpected quick change of the magnetic structure is the magnetic frustration of the Fe(2a) sites. The magnetic frustration is caused by the noncollinearity of the Fe(6h) magnetic sublattice. The noncollinearity arises from the rotation of the magnetic moments due to the competition between the ferromagnetic exchange interactions and the antiferromagnetic Fe(6h)–Ti–Fe(6h) interaction. In the compounds with x=0.4–0.6, the temperature transitions to the antiferromagnetic state are observed. As an example, the Hf_0.4Ti_0.6Fe₂ compound is completely antiferromagnetic above 200 K.     

Temperature-dependent Fe Mössbauer spectroscopy and local structure of the mullite-type Bi2(FexGa1−x)4O9 (0.1≤x≤1) solid solution

The Bi₂(Fe_xGa_1−x)₄O₉ oxide solid solution possessing a mullite-type structure has been investigated by ⁵⁷Fe Mössbauer spectroscopy in dependence of composition (0.1≤x≤1) and temperature (293≤T/K≤1073). The spectra have been fitted with two doublets for tetrahedrally and octahedrally coordinated high-spin Fe³⁺ ions, respectively. The experimental areas of the subspectra were used to determine the distribution of iron on the two inequivalent structural sites. The fraction of iron cations occupying the octahedral site is found to increase with decreasing Fe content and the cation distribution is almost independent of temperature. The unusual temperature dependence of the quadrupolar splitting, QS, observed for the octahedral site with dQS/dT>0 is discussed in connexion with structural data for Bi₂Fe₄O₉. The temperature dependence of Mössbauer isomer shifts and signal intensities is examined in the context of local vibrational properties of iron on the two inequivalent sites of the mullite-type lattice structure.     

Magnetic properties of RE0.7Ca0.3Mn0.95Fe0.05O3 (RE=Sm and Gd) manganites at low temperature

The magnetic properties of RE_0.7Ca_0.3Mn_0.95Fe_0.05O₃ perovskite with rare-earth cations (RE=Sm and Gd) were investigated by means of X-ray diffraction, Mössbauer spectroscopy, and low temperature (4.2-266 K) magnetization measurements. Structural characterization of these compounds shows that they both have orthorhombic (Pbnm) structure. The Mössbauer spectra show clear evidence of local structural distortion of the Mn(Fe)O₆ octahedron, which is based on the non-zero nuclear quadrupole interactions for high-spin Fe³⁺ ions. It was found that the local structural distortion increases significantly when Sm³⁺ is replaced by Gd³⁺. This distortion is attributed to the Jahn-Teller coupling strength as estimated from the Mössbauer effect results. The magnetic results indicate that the Curie temperature decreases as a result of replacing Sm by Gd. This is due to the decrease of the average A-site cationic radius 〈r_A〉. The rapid increase of magnetization at low temperature indicates the magnetic ordering of rare earth ions at the A-site.     

Influence of doping concentration on room-temperature ferromagnetism for Fe-doped BaTiO3 ceramics

Ba(Ti_1−xFe_x)O₃ ceramics (x=7, 30 and 70 at%) were prepared by solid-state reaction. All samples are single-phase with 6H-BaTiO₃-type hexagonal perovskite structure. Mössbauer spectra show all Fe atoms to be present as Fe³⁺ in BaTiO₃ lattice, occupying M1 octahedral and pentahedral sites. Room-temperature ferromagnetism is exhibited and saturation magnetization gradually decreases with increasing Fe content. The observed ferromagnetism is considered to be an intrinsic property of Ba(Ti_1−xFe_x)O₃, originating from super-exchange interactions between Fe³⁺ in different occupational sites associated with oxygen vacancies. The variation in magnetization with Fe content is related to the ratio of pentahedral to octahedral sites and oxygen vacancies.     

PLD of Fe3O4 thin films: Influence of background gas on surface morphology and magnetic properties

Ablation of Fe₃O₄ targets has been performed using a pulsed UV laser (KrF, λ = 248 nm, 30 ns pulse duration) onto Si(100) substrates, in reactive atmospheres of O₂ and/or Ar, with different oxygen partial pressures. The as-deposited films were characterised by atomic force microscopy (AFM), X-ray diffraction (XRD), conversion electron Mössbauer spectroscopy (CEMS) and extraction magnetometry, in order to optimise the deposition conditions in the low temperature range. The results show that a background mixture of oxygen and argon improves the Fe:O ratio in the films as long as the oxygen partial pressure is maintained in the 10⁻² Pa range. Thin films of almost stoichiometric single phase polycrystalline magnetite, Fe_2.99O₄, have been obtained at 483 K and working pressure of 7.8 × 10⁻² Pa, with a high-field magnetization of ∼490 emu/cm³ and Verwey transition temperature of 112 K, close to the values reported in the literature for bulk magnetite.     

Synthesis and laser patterning of Bi-doped Y3Fe5O12 crystals in germanosilicate glasses

New germanosilicate glasses giving the crystallization of yttrium iron garnet Y₃Fe₅O₁₂ (YIG) and Bi-doped YIG, 23Na₂O-xBi₂O₃-(12−x)Y₂O₃-25Fe₂O₃-20SiO₂-20GeO₂ (mol%), are developed, and the laser-induced crystallization technique is applied to the glasses to pattern YIG and Bi-doped YIG crystals on the glass surface. It is clarified from the Mössbauer effect measurements that iron ions in the glasses are present mainly as Fe³⁺. It is suggested from the X-ray diffraction analyses and magnetization measurements that Si⁴⁺ ions are incorporated into YIG crystals formed in the crystallization of glasses. The irradiations (laser power: 32-60 mW and laser scanning speed: 7 μm/s) of continuous wave Yb:YVO₄ fiber laser (wavelength: 1080 nm) are found to induce YIG and Bi-doped YIG crystals, indicating that Fe³⁺ ions in the glasses act as suitable transition metal ions for the laser-induced crystallization. It is suggested that YIG and Bi-doped YIG crystals in the laser irradiated part might orient. The present study will be a first step for the patterning of magnetic crystals containing iron ions in glasses.     

Microstructure and some magnetic properties of bulk amorphous (Fe0.61Co0.10Zr0.025Hf0.025Ti0.02W0.02B0.20)100−xYx (x=0, 2, 3 or 4) alloys

Microstructure, revealed by X-ray diffraction, transmission electron microscopy and Mössbauer spectroscopy, and magnetic properties such as magnetic susceptibility, its disaccommodation, core losses and approach to magnetic saturation in bulk amorphous (Fe_0.61Co_0.10Zr_0.025Hf_0.025Ti_0.02W_0.02B_0.20)_100−xY_x (x=0, 2, 3 or 4) alloys in the as-cast state and after the annealing in vacuum at 720 K for 15 min. are studied. The investigated alloys are ferromagnetic at room temperature. The average hyperfine field induction decreases with Y concentration. Due to annealing out of free volumes its value increases after the heat treatment of the samples. The magnetic susceptibility and core losses point out that the best thermal stability by the amorphous (Fe_0.61Co_0.10Zr_0.025Hf_0.025Ti_0.02W_0.02B_0.20)₉₇Y₃ alloy is exhibited. Moreover, from Mössbauer spectroscopy investigations it is shown that the mentioned above alloy is the most homogeneous. The atom packing density increases with Y concentration, which is proved by the magnetic susceptibility disaccommodation and approach to magnetic saturation studies.     

Studies on Structural, Magnetic and Thermal Properties of xFe2TiO4-(1−x)Fe3O4 (0≤x≤1) Pseudo-binary System

The xFe₂TiO₄-(1−x)Fe₃O₄ pseudo-binary systems (0≤x≤1) of ulvöspinel component were synthesized by solid-state reaction between ulvöspinel Fe₂TiO₄ precursors and commercial Fe₃O₄ powders in stochiometric proportions. Crystalline structures were determined by X-ray powder diffraction (XRD) and it was found that the as-obtained titanomagnetites maintain an inverse spinel structure. The lattice parameter a of synthesized titanomagnetite increases linearly with the increase in the ulvöspinel component. ⁵⁷Fe room temperature Mössbauer spectra were employed to evaluate the magnetic properties and cation distribution. The hyperfine magnetic field is observed to decrease with increasing Fe₂TiO₄ component. The fraction of Fe²⁺ in both tetrahedral and octahedral sites increases with the increase in Ti⁴⁺ content, due to the substitution and reduction of Fe³⁺ by Ti⁴⁺ that maintains the charge balance in the spinel structure. For x in the range of 0 ≤x≤0.4, the solid solution is ferrimagnetic at room temperature. However, it shows weak ferrimagnetic and paramagnetic behavior for x in the range of 0.4<x≤0.7. When x>0.70, it only shows paramagnetic behavior, with the appearance of quadrupole doublets in the Mössbauer spectra. Simultaneous differential scanning calorimetry and thermogravimetric analysis (DSC-TGA) studies showed that magnetite is not stable, and thermal decomposition of magnetite occurs with weight losses accompanying with exothermic processes under heat treatment in inert atmosphere.     

Mössbauer study of Na0.82Co0.99Fe0.01O2

We studied by Mössbauer spectroscopy the Na_0.82CoO₂ compound using 1% ⁵⁷Fe as a local probe which substitutes for the Co ions. Mössbauer spectra at T=300 K revealed two sites which correspond to Fe³⁺ and Fe⁴⁺. The existence of two distinct values of the quadrupole splitting instead of a continuous distribution should be related with the charge ordering of Co⁺³, Co⁺⁴ ions and ion ordering of Na(1) and Na(2). Below T=10 K part of the spectrum area, corresponding to Fe⁴⁺ and all of Fe³⁺, displays broad magnetically split spectra arising either from short-range magnetic correlations or from slow electronic spin relaxation.     

Magnetic properties of nanocrystalline Ni0.7Mn0.3Gd0.1Fe1.9O4 ferrite at low temperatures

Mössbauer spectra and magnetic measurement of Ni_0.7Mn_0.3Gd_0.1Fe_1.9O₄ ferrite were investigated by Oxford MS-500 Mössbauer spectrometer and superconducting quantum interference device (SQUID) magnetometer with a field 5 T. Ni_0.7Mn_0.3Gd_0.1Fe_1.9O₄ nanoparticles have a considerable coercivity of 1040 Oe when the test temperature is reduced to 2 K. Mössbauer spectra show that Ni_0.7Mn_0.3Gd_0.1Fe_1.9O₄ nanoparticles exhibit superparamagnetism at room temperature and ferrimagnetism at 77 K.     

Oxygen non-stoichiometry and defect thermodynamics in La2Ni0.9Fe0.1O4+δ

The oxygen hyperstoichiometry of K₂NiF₄-type La₂Ni_0.9Fe_0.1O_4+δ, studied by thermogravimetric analysis and coulometric titration in the oxygen partial pressure range 6×10⁻⁵-0.7 atm at 923-1223 K, is considerably higher than that of undoped lanthanum nickelate. The p(O₂)-T-δ diagram of iron-doped lanthanum nickelate can be adequately described by introducing point-defect interaction energy in the concentration-dependent part of defect chemical potentials and accounting for the site-exclusion effects. The critical factors affecting the equilibrium oxygen incorporation process include coulombic repulsion of interstitial anions, trapping of the p-type electronic charge carriers by iron, and interaction between Fe³⁺ and holes localized on nickel cations. Due to low chemical expansion of La₂Ni_0.9Fe_0.1O_4+δ lattice, the thermodynamic functions governing oxygen intercalation, site-blocking factors and hole mobility are all independent of the defect concentrations. The predominant 3+ state of iron cations under oxidizing conditions was confirmed by the Mössbauer spectroscopy. The stability of La₂NiO₄-based phase in reducing atmospheres is essentially unaffected by doping.     

Synthesis and characterization of the xZnO-(1−x)α-Fe2O3 nanoparticles system

The xZnO-(1−x)α-Fe₂O₃ nanoparticles system has been obtained by mechanochemical activation for x=0.1, 0.3 and 0.5 and for ball milling times ranging from 2 to 24 h. Structural and morphological characteristics of the zinc-doped hematite system were investigated by X-ray diffraction (XRD) and Mössbauer spectroscopy. The Rietveld structure of the XRD spectra yielded the dependence of the particle size and lattice constant on the amount x of Zn substitutions and as function of the ball milling time. The x=0.1 XRD spectra are consistent with line broadening as Zn substitutes Fe in the hematite structure and the appearance of the zinc ferrite phase at milling times longer than 4 h. Similar results were obtained for x=0.3, while for x=0.5 the zinc ferrite phase occurred at 2 h and entirely dominated the spectrum at 24 h milling time. The Mössbauer spectra corresponding to x=0.1 exhibit line broadening as the ball milling time increases, in agreement with the model of local atomic environment. Because of this reason, the Mössbauer spectrum for 12 h of milling had to be fitted with two sextets. For x=0.3 and 12 milling hours, the Mössbauer spectrum reveals the occurrence of a quadrupole-split doublet, with the hyperfine parameters characteristic to zinc ferrite, ZnFe₂O₄. This doublet clearly dominates the Mössbauer spectrum for x=0.5 and 24 h of milling, demonstrating that the entire system of nanoparticles consists finally of zinc ferrite. As ZnO is not soluble in hematite in the bulk form, the present study clearly demonstrates that the solubility limits of an immiscible system can be extended beyond the limits in the solid state by mechanochemical activation. Moreover, this synthesis route allowed us to reach nanometric particle dimensions, which would make the materials very important for gas sensing applications.     

Critical behaviour and magnetic properties of A-B spinel ZnxCu1−xFe2O4

Polycrystalline Zn_0.6Cu_0.4Fe₂O₄ ferrites have been prepared using a solid-state reaction technique. Their structural and magnetic properties have been studied, using X-ray diffraction and Mössbauer and magnetic measurements. These results have been compared to a more general theoretical study, on Zn_xCu_1−xFe₂O₄, based on mean field theory and high-temperature series expansions (HTSE), and extrapolated with the Padé approximant method. The nearest neighbour super-exchange interactions for the intra-site and the inter-site of Zn_xCu_1−xFe₂O₄ spinel ferrites, in the range 0≤x≤1, have been computed using the probability approach, based on Mössbauer data. The Curie temperature T_C is calculated as a function of Zn concentration. The theoretical results obtained are in good agreement with the experimental results obtained by magnetic measurements.     

Spin glass ordering of Zn0.75Co0.25Fe0.5Cr1.5O4 cubic spinel

The linear and nonlinear low field AC susceptibilities of Zn_0.75Co_0.25Fe_0.5Cr_1.5O₄ show peaks due to non-critical contributions, which mask the peak due to spin glass ordering. They extend into the region of temperatures in which Mössbauer spectra do not show any magnetic component. When a DC field of 200 Oe suppresses the non-critical contributions, peak due to spin glass ordering is clearly visible. The spin glass ordering is thus shown to be a thermodynamic transition. The critical exponent is found to fall within the range found using other spin glasses. Mössbauer spectra in zero fields provide T_SG, which agrees with the peak temperature of AC susceptibilities in the absence of non-critical contributions. 〈S_Z〉 determined using Mössbauer spectra does not show any anomaly. In the presence of a field of 5 T, the spectra show SG ordering at 4.2 K, which converts into ferrimagnetic ordering at higher temperatures.     

BiFeO3 ceramic matrix with Bi2O3 or PbO added: Mössbauer, Raman and dielectric spectroscopy studies

In this paper Mössbauer, Raman and dielectric spectroscopy studies of BiFeO₃ (BFO) ceramic matrix with 3 or 10 wt% of Bi₂O₃ or PbO added, obtained through a new procedure based on the solid-state method, are presented. Mössbauer spectroscopy shows the presence of a single magnetically ordered phase with a hyperfine magnetic field of 50 T. Raman spectra of BFO over the frequency range of 100-900 cm⁻¹ have been investigated, at room temperature, under the excitation of 632.8 nm wavelength in order to evaluate the effect of additives on the structure of the ceramic matrix. Detailed studies of the dielectric properties of BiFeO₃ ceramic matrix like capacitance (C), dielectric permittivity (ε) and dielectric loss (tan δ), were investigated in a wide frequency range (1 Hz-1 MHz), and in a temperature range (303-373 K). The complex impedance spectroscopy (CIS) technique, showed that these properties are strongly dependent on frequency, temperature and on the added level of impurity. The temperature coefficient of capacitance (TCC) of the samples was also evaluated. The study of the imaginary impedance (−Z″) and imaginary electric modulus (M″) as functions of frequency and temperature leads to the measurement of the activation energy (E_ac), which is directly linked to the relaxation process associated with the interfacial polarization effect in these samples.