Vacuum Annealing Induced Room-Temperature Ferromagnetism in Co0.1Ti0.9O2-δ Films Prepared by Sol-Gel Method

The Co-doped TiO2 films （Co0.1Ti0.9O2-δ） are prepared on silicon substrates by sol-gel method and post annealing. TheCo0.1Ti0.9O2-δ film annealed in air is non-ferromagnetic at room temperature. After further annealed in a vacuum, the room-temperature ferromagnetism （RTFM） is observed. Experimental evidences show that the RTFM in the Co0.1Ti0.9O2-δ film may come from the Co-doped TiO2 matrix and is related to the oxygen vacancies created by vacuum annealing.     

Structural and photoluminescence characteristics of ZnO films by room temperature sputtering and rapid thermal annealing process

ZnO thin films deposited on SiO₂/Si substrates at room temperature by sputtering technology were annealed with a rapid thermal annealing process at various temperatures from 200 °C to 900 °C. The physical and optical properties of the ZnO films were investigated by X-ray diffraction, scanning electron microscopy and room-temperature photoluminescence (PL). The surface structures of the thin films showed great variations with increased annealing temperature. The PL spectrum illustrated that a stronger UV emission intensity appeared at an annealing temperature of 500 °C. On the other hand, visible-light emission could be obtained when the ZnO films were annealed above 500 °C and reached a maximum intensity at 900 °C. The possible mechanisms for visible-light emission are discussed. PACS 81.15.Cd; 81.40.Ef; 78.55.-m; 78.55.Et     

退火对溶胶-凝胶法制备的ZnO薄膜结构和光致发光的影响

采用溶胶-凝胶法在n-Si(100)衬底上制备ZnO薄膜并从三个方面对其研究。X射线衍射结果表明,在含氧气氛中退火的ZnO薄膜为多晶六角纤锌矿结构,有明显的c轴择优结晶取向;退火时间的长短和温度的高低对结晶取向性和粒径均有较大影响,通过进一步的研究发现最佳处理温度在500℃左右。用扫描电子显微镜观察样品的表面和侧面形貌,晶体的生长比较均匀,粒径平均在70~160nm范围内,与XRD测量结果相一致。室温下ZnO胶体的光致发光谱表明,随着胶体老化时间的延长,胶体的紫外峰位发生了蓝移。室温下ZnO薄膜的光致发光谱表明,紫外部分的发光峰位在365,390nm,发光强度较强;在可见光区的发光强度相对较弱,但是还没有被氧完全抑制掉。     

纳米ZnO薄膜可见发射机制研究

利用溶胶－凝胶法 （Sol-Gel）制备了纳米ZnO薄膜,获得了高强的近紫外发射室温下测量了样品的光致发光谱(PL )、吸收谱(ABS)、X射线衍射谱(XRD).X射线衍射(XRD)的结果表明：纳米ZnO薄膜呈多晶态,具有六角纤锌矿结构和良好的C轴取向;发现随退火温度升高,（002）衍射峰强度显著增强,衍射峰的半高宽（FWHM）减小、纳米颗粒的粒径增大.由吸收谱(ABS)给出了样品室温下带隙宽度为3.30 eV.在PL谱中观察到二个荧光发射带,一个是中心波长位于392 nm附近强而尖的紫带,另一个是519 nm附近弱而宽的绿带研究了不同退火温度样品的光致发光峰值强度的变化关系,发现随退火温度升高,紫带峰值强度增强、绿带峰值强度减弱,均近似呈线性变化.证实了纳米ZnO薄膜绿光发射主要来自氧空位(Vo)形成的浅施主能级与锌空位(VZn)形成的浅受主能级之间的复合,或氧空位(Vo)形成的深施主能级上的电子至价带顶的跃迁;紫带来自于导带中的电子与价带中的空位形成的激子复合.     

Novel magnetic behavior of Mn-doped ZnO hierarchical hollow spheres

In this study, unique three-dimensional Zn_0.98Mn_0.02O hierarchical hollow microspheres (HHMs) with diameters of 5–8 μm have been synthesized by a simple hydrothermal approach. In particular, room-temperature magnetization measurements indicate that novel co-existence of ferromagnetism (FM)/paramagnetism (PM) and only PM behaviors for the as-annealed Zn_0.98Mn_0.02O HHMs at 673 and 1,073 K, respectively, in Ar gas atmosphere appear, whereas the as-synthesized ones show merely pure FM. Based on the Photoluminescence and Raman spectra, it is confirmed that the concentrations of oxygen vacancies in Zn_0.98Mn_0.02O HHMs were becoming larger and larger with increasing annealing temperature. Corresponding magnetic evolution mechanism is proposed to relate to oxygen vacancies based on annealing processes. This novel magnetic property will enrich our understanding of diluted magnetic semiconductors.     

Influence of annealing process on conductive properties of Nb-doped TiO2 polycrystalline films prepared by sol-gel method

Nb-doped TiO₂ (TNO) thin films were prepared by sol-gel dip-coating method with Nb content in a wide range of 0-20 at.%. The prepared films were preheated at 400 °C and then undertaken by two different post-annealing processes: (a) three times vacuum annealing and (b) multi-round annealing. The designed multi-round annealing was shown to be an effective way to improve the conductive properties of the films, compared to the traditional vacuum annealing process. The minimum resistivity reached approximately 0.5 Ω cm with Nb doping concentration around 12 at.%, and the carrier density increased with Nb-doping concentration until the critical point of 12 at.%, which might be the optimal doping content for our TNO films prepared by sol-gel method.     

Near-field scanning microwave microscope application on Cu-phthalocyaninethin-film organic field-effect transistor

By the standard vacuum evaporation technique Cu(II)-phthalocyanine (Cu-Pc) thin films have been fabricated. For the samples, prepared at room temperature and post-annealed from 100°C to 350°C temperatures, optical spectra in the visible and near IR ranges have been measured. By using nondestructive near-field scanning microwave microscopy organic field-effect transistor (OFET) based on Cuphthalocyanine thin films have been investigated. The changes of crystal structure of Cuphthalocyanine thin film from the α- to the β-phase were controlled by the temperature of annealing. The values of holes’ mobility and the electroconductivity of Cu-phthalocyanine thin films have been obtained depending on the annealing temperature.     

Effect of excimer laser annealing on the properties of ZnO thin film prepared by sol-gel method

Pristine ZnO thin films have been deposited with zinc acetate [Zn(CH₃COO)₂], mono-ethanolamine (stabilizer), and isopropanol solutions by sol-gel method. After deposition, pristine ZnO thin films have been irradiated by excimer laser (λ = 248, KrF) source with energy density of 50 mJ/cm² for 30 sec. The effect of excimer laser annealing on the optical and structural properties of ZnO thin films are investigated by photoluminescence and field emission scanning electron microscope. As-grown ZnO thin films show a huge peak of visible region and a wide full width at half maximum (FWHM) of UV region due to low quality with amorphous ZnO thin films. After KrF excimer laser annealing, ZnO thin films show intense near-band-edge (NBE) emission and weak deep-level emission. The optically improved pristine ZnO thin films have demonstrated that excimer laser annealing is novel treatment process at room temperature.     

Effect of oxygen annealing on the photoresponse of PbSe thin films fabricated by the pulsed laser deposition method

In this work, we have fabricated lead selenide (PbSe) thin films by the pulsed laser deposition method on Si/SiO₂ substrates and investigated the effect of oxygen annealing (sensitization) in these films. The oxygen-sensitized films show high responsivity in the visible (VIS) and the near-infrared (NIR) region at room temperature without cooling. We also demonstrate the effective surface oxidation of PbSe thin films during the oxygen annealing process without treated with commonly used halogens that leads to a better photoresponse in these PbSe films.     

Properties of NiO thin films deposited by chemical spray pyrolysis using different precursor solutions

NiO thin films have been deposited by chemical spray pyrolysis using a perfume atomizer to grow the aerosol. The influence of the precursor, nickel chloride hexahydrate (NiCl₂·6H₂O), nickel nitrate hexahydrate (Ni(NO₃)₂·6H₂O), nickel hydroxide hexahydrate (Ni(OH)₂·6H₂O), nickel sulfate tetrahydrate (NiSO₄·4H₂O), on the thin films properties has been studied. In the experimental conditions used (substrate temperature 350 °C, precursor concentration 0.2-0.3 M, etc.), pure NiO thin films crystallized in the cubic phase can be achieved only with NiCl₂ and Ni(NO₃)₂ precursors. These films have been post-annealed at 425 °C for 3 h either in room atmosphere or under vacuum. If all the films are p-type, it is shown that the NiO films conductivity and optical transmittance depend on annealing process. The properties of the NiO thin films annealed under room atmosphere are not significantly modified, which is attributed to the fact that the temperature and the environment of this annealing is not very different from the experimental conditions during spray deposition. The annealing under vacuum is more efficient. This annealing being proceeded in a vacuum no better than 10⁻² Pa, it is supposed that the modifications of the NiO thin film properties, mainly the conductivity and optical transmission, are related to some interaction between residual oxygen and the films.     

Structural and Magnetic Properties of Fe-Doped Anatase TiO2 Films Annealed in Vacuum

Structural and magnetic properties of Fe-doped anatase TiO2 films fabricated by sol-gel spin coating are investigated. X-ray diffraction measurements reveal that Fe^3＋ ions are incorporated into the TiO2 lattice. No ferromagnetism-related secondary phases and magnetic nanopaxticles are observed in the films. The presence of electron paramagnetic resonance signals at 9- 2.0 supports oxygen vacancies and/or defects generated in the films after annealing in vacuum. Magnetic measurements indicate that Fe-doped anatase TiO2 films are ferromagnetic at room temperature. These observations suggest that oxygen vacancies and/or defects axe energetically favorable for the long range Fe^3＋-Fe^3＋ ferromagnetic coupling in Fe-doped anatase TiO2 films.     

Reversible wettability of nanostructured ZnO thin films by sol-gel method

Nanostructured ZnO thin films were deposited on Si(1 1 1) and quartz substrate by sol-gel method. The thin films were annealed at 673 K, 873 K, and 1073 K for 60 min. Microstructure, surface topography, and water contact angle of the thin films have been measured by X-ray diffractometer, atomic force microscopy, and water contact angle apparatus. XRD results showed that the ZnO thin films are polycrystalline with hexagonal wurtzite structure. AFM studies revealed that rms roughness changes from 2.3 nm to 7.4 nm and the grain size grow up continuously with increasing annealing temperature. Wettability results indicated that hydrophobicity of the un-irradiated ZnO thin films enhances with annealing temperature increase. The hydrophobic ZnO surfaces could be reversibly switched to hydrophilic by alternation of UV illumination and dark storage (thermal treatment). By studying the magnitude and the contact angle reduction rate of the light-induced process, the contribution of surface roughness is discussed.     

Influence of atmospheric exposure of tris (8-hydroxyquinoline) aluminum (Alq<Subscript>3</Subscript>): a photoluminescence and absorption study

We have investigated the effects of atmospheric exposure on the properties of tris (8-hydroxyquinoline) aluminum (Alq₃) thin films by photoluminescence (PL) and UV-Vis absorption measurements. Alq₃ films were evaporated on glass substrates at different temperatures. The influence of annealing on the environmental stability of the films has also been investigated. It has been found that deposition at higher substrate temperature and annealing of the samples deposited at room temperature yield an improvement in the environmental stability of the films, i.e. less decrease in the PL intensity over time with exposure to atmosphere, as well as increased PL intensity. To investigate further the effects of the air exposure, films deposited at room temperature were stored for four days in air, nitrogen, and oxygen. No decrease in PL intensity has been found for storage in nitrogen, while the decrease for the film stored in oxygen was smaller than that for the film stored in air, indicating that both humidity and oxygen play a role in the PL intensity decrease in Alq₃ thin films. PACS 78.55.Kz; 78.40.Me     

Evolution of structural and magnetic properties with varying oxygen content in low-bandwidth manganite Pr0.9Ca0.1MnO3 thin films

The effects of ex situ vacuum and oxygen annealing treatments on thin films of the low-bandwidth compound Pr(1-x)Ca(x)MnO(3) (PCMO) are investigated. Structural and magnetic measurements reveal that increased ferromagnetism can be achieved by oxygen annealing treatment, which is linked to the increased Mn(4+) ion content, as observed from x-ray photoelectron spectroscopy (XPS) measurements, as well as relaxation of the substrate-induced tensile strain of the PCMO unit cell. The increased number of Mn(4+) ions and partial release of strain lead to stronger double-exchange interaction in the system. Vacuum annealing increases the ferromagnetic (FM) interaction as well; however, the increased FM ordering is not directly related to the improved double-exchange interaction, as XPS measurement reveals an indication of a slight increase in Mn(3+) ions in this case. Trapping of carriers in the oxygen vacancies and formation of magnetic polarons have been suggested as the causes of the increase in ferromagnetic ordering, and this is also supported by the large coercivity and longer spin memory in the vacuum annealed PCMO.     

The Al-doping and post-annealing treatment effects on the structural and optical properties of ZnO:Al thin films deposited on Si substrate

Al-doped ZnO (ZnO:Al) thin films with different Al contents were deposited on Si substrates using the radio frequency reactive magnetron sputtering technique. X-ray diffraction (XRD) measurements showed that the crystallinity of the films was promoted by appropriate Al content (0.75 wt.%). Then the ZnO:Al film with Al content of 0.75 wt.% was annealed in vacuum at different temperatures. XRD patterns revealed that the residual compressive stress decreased at higher annealing temperatures. While the surface roughness of the ZnO:Al film annealed at 300 °C became smoother, those of the ZnO:Al films annealed at 600 and 750 °C became rougher. The photoluminescence (PL) measurements at room temperature revealed a violet, two blue and a green emission. The origin of these emissions was discussed and the mechanism of violet and blue emission of ZnO:Al thin films were suggested. We concluded that the defect centers are mainly ascribed to antisite oxygen and interstitial Zn in annealed (in vacuum) ZnO:Al films.     

The role of oxygen vacancies in magnetism of CoxTi1−xO2−δ films on Si(001) prepared by sol-gel method

Co_xTi_1−xO_2−δ films have been prepared on Si(001) substrates by sol-gel method. When heat treated in air, Co_xTi_1−xO_2−δ films are non-ferromagnetic at room temperature. However, after further vacuum annealing or hydrogenation, Co_xTi_1−xO_2−δ films show room-temperature ferromagnetism (RTFM). When the vacuum annealed Co_xTi_1−xO_2−δ films are reheated in air, the magnetic moments of the films strongly reduce. After these films are vacuum annealed once again, the magnetic moments are greatly enhanced, confirming the role of vacuum annealing in ferromagnetism of Co_xTi_1−xO_2−δ films. The x-ray diffraction (XRD), x-ray photoelectron spectroscopy (XPS) and measurements of magnetization (M) vs temperature (T) fail to detect Co clusters in the vacuum annealed and the hydrogenated Co_xTi_1−xO_2−δ films. Oxygen vacancies are formed in Co_xTi_1−xO_2−δ films after vacuum annealing and hydrogenation, determined by XRD and XPS measurements. These results indicate that oxygen vacancies created by vacuum annealing and hydrogenation play an important role in the generation of RTFM in Co_xTi_1−xO_2−δ films.     

Effect of annealing conditions on structural and magnetic properties of laser ablated copper ferrite thin films

The effect of annealing conditions on structural and magnetic properties of copper ferrite thin films on (100) Si substrates was examined in detail. After deposition, the ferrite thin films were post-annealed in vacuum and in oxygen atmosphere for several hours. It is found that the crystal structure of CuFe₂O₄ thin films changed drastically depending on different heating process. A maximum magnetization was achieved in the film that was vacuum annealed and it decreased remarkably after oxygen annealing.     

二氧化钒薄膜的低温制备及其性能研究

针对VO₂薄膜在微测辐射热计上的应用，采用射频反应溅射法，在室温下制备氧化钒薄膜；研究了氧分压对薄膜沉积速率、电学性质及成分的影响.通过调节氧分压，先获得成分接近VO₂的非晶化薄膜，再在400℃空气中氧化退火，便可制得高电阻温度系数，低电阻率的VO₂薄膜，电阻温度系数约为-4%/℃，薄膜方块电阻为R_□为100—300kΩ；薄膜在室温下沉积，400℃下退火的制备方法与微机电加工(micro electromechanic 关键词： 二氧化钒 电阻温度系数 氧分压 射频反应溅射法     

Effect of post annealing temperature on structural and optical properties of ZnCdO thin films deposited by sol–gel method

Ternary ZnCdO thin films oriented along c-axis have been successfully deposited on p-Si (1 0 0) substrates using sol–gel spin coating route. To optimize most suitable annealing temperature for the Zn_1−xCd_xO thin films; these films with selected cadmium content x = 0.10 were treated at annealing temperatures from 300 °C up to 800 °C in oxygen ambient after deposition. The structural and optical properties of deposited thin films have been characterized by X-ray diffraction, energy dispersive spectroscopy, atomic force microscopy, UV–Vis spectroscopy, and photoluminescence spectra. The results show that the obtained films possess high crystallinity with wurtzite structure. The crystallite size, lattice parameters, lattice strain and stress in the deposited films are determined from X-ray diffraction analysis. The band gap energy increased as a function of annealing temperatures as observed from optical reflectance spectra of samples. The presence of Cd in the deposited films is confirmed by energy dispersive spectrum and it is observed that Cd re-evaporate from the lattice with annealing. The photoluminescence measurements as performed at room temperature did not exhibit any luminescence related to oxygen vacancies defects for lower annealing temperatures, as normally displayed by ZnO films. The green yellow luminescence associated to these defects was observed at higher annealing temperatures (≥700 °C).     

Room temperature photoluminescence from amorphous silicon nanoparticles in SiOx thin films

Amorphous SiO_x thin films with four different oxygen contents (x=1.15, 1.4, 1.5, and 1.7) have been prepared by thermal evaporation of SiO in vacuum and then annealed at 770 or 970 K in argon for various times ?40 min. The influence of annealing conditions and the initial film composition on photoluminescence (PL) from the annealed films has been explored. Intense room temperature PL has been observed from films with x?1.5, visible with a naked eye. It has been shown that PL spectra of most samples consists of two main bands: (i) a ‘green’ band centered at about 2.3 eV, whose position does not change with annealing conditions and (ii) an ‘orange-red’ band whose maximum moves from 2.1 to 1.7 eV with increasing annealing time and temperature and decreasing initial oxygen content. These observations have been explained assuming recombination via defect states in the SiO_x matrix for the first band and emission from amorphous Si nanoparticles for the second one.