Optical properties and mechanical characteristics of transparent nanostructured Zn1−xMnxO thin films

Uniform and transparent thin films of Zn_1−xMn_xO (0?x?0.10) were fabricated by a sol-gel spin coating method. XRD results indicated the hexagonal structure of ZnO as the primary phase at all concentrations (x) of Mn. However, at x?0.035, Mn₃O₄ (tetragonal) is observed as the secondary phase, which was confirmed by selected-area electron diffraction patterns. SEM and TEM results showed a tendency of grains to arrange into wire-shaped morphologies, leading to elongated needle-like structures at high Mn addition. Increasing Mn content in the range 0?x?0.10 led to quenching of photoluminescence, increase in the band gap (E_g) from 3.27 to 3.33 eV, and increase in film thickness, refractive index and extinction coefficient of Zn_1−xMn_xO thin films. The residual stress evaluated was compressive in all cases and found to increase by an order of magnitude with addition of Mn. Furthermore, an overall increase in microhardness and yield strength of Zn_1−xMn_xO thin films at higher Mn concentrations is attributed to change in microstructures, presence of secondary phase and increase in film thickness.     

Structural and magnetic properties of Mg(In2−xMnx)O4 system

We synthesized the Mn-doped Mg(In_2−xMn_x)O₄ oxides with 0.03?x?0.55 using a solid-state reaction method. The X-ray diffraction patterns of the samples were in a good agreement with that of a distorted orthorhombic spinel phase. Their lattice parameters and unit-cell volumes decrease with x due to the substitution of the smaller Mn³⁺ ions to the larger In³⁺ ions. The undoped MgIn₂O₄ oxide presents diamagnetic signals for 5 K?T?300 K. The M(H) at T=300 K reveals a fairly negative-sloped linear relationship. Neither magnetic hysteresis nor saturation behavior was observed in this parent sample. For the Mn-doped samples, however, positive magnetization were observed between 5 and 300 K even if the x value is as low as 0.03. The mass susceptibility enhances with Mn content and it reaches the highest value of 1.4×10⁻³ emu/g Oe (at T=300 K) at x=0.45. Furthermore, the Mn-doped oxides with x=0.06 and 0.2, respectively, exhibit nonlinear magnetization curves and small hysteretic loops in low magnetic fields. Susceptibilities of the Mn-doped samples are much higher than those of MnO₂, Mn₂O₃ oxides, and Mn metals. These results show that the oxides have potential to be magnetic semiconductors.     

Microstructure characterization and magnetic behavior of NiAlxFe2−xO4 and Ni1−yMnyAl0.2Fe1.8O4 ferrites

NiAl_xFe_2−xO₄ and Ni_1−yMn_yAl_0.2Fe_1.8O₄ ferrites were prepared by the conventional ceramic method and were characterized by X-ray diffraction, scanning electron microscopy, and magnetic measurements. The single spinel phase was confirmed for all prepared samples. A proper explanation of data is possible if the Al³⁺ ions are assumed to replace Fe³⁺ ions in the A and B sites simultaneously for NiAl_xFe_2−xO₄ ferrites, and if the Mn²⁺ ions are assumed to replace Ni²⁺ ions in the B sites for Ni_1−yMn_yAl_0.2Fe_1.8O₄ ferrites. Microstructural factors play an important role in the magnetic behavior of Ni_1−yMn_yAl_0.2Fe_1.8O₄ ferrites with large Mn²⁺ content.     

On the structural analysis and magnetic behavior of heavily doped Zn1−xMnxO nanopowders synthesized by wet chemistry method

Nanocrystalline Zn_1−xMn_xO(x=0−0.1) powders are prepared by polymeric precursor method and their structural and magnetic properties carefully studied. X-ray diffraction studies and Raman spectroscopy reveal that Mn²⁺ ions have substituted the Zn²⁺ ion without changing the würtzite structure of pristine ZnO up to Mn concentrations x≤0.05. The presence of a secondary phase, related to the solubility of Mn in ZnO is evident for higher Mn-doping concentrations. The negative value obtained for the Curie–Weiss temperature indicates that the interactions between the Mn ions are predominantly antiferromagnetic. Thus, no bulk ferromagnetism is evident in any of the studied samples.     

Structural and magnetic properties of Co1−xZnxFe2O4 nanoparticles by co-precipitation method

Co_1−xZn_xFe₂O₄ nanoparticles were prepared by co-precipitation method with x varying from 0 to 1.0. The powder samples were characterized by X-ray diffraction (XRD), vibrating sample magnetometer (VSM) and Fourier transform infrared spectroscopy (FTIR). The average crystallite sizes of the particles were determined from XRD. X-ray analysis showed that the samples were cubic spinel. The average crystallite size (D_aveXR) of the particles precipitated was found to vary from 6.92 to 12.02 nm decreasing with the increase in zinc substitution. The lattice constant (a_o) increased with the increase in zinc substitution. The specific saturation magnetization (M_S) of the particles was measured at room temperature. The magnetic parameters such as M_S, H_c, and M_r were found to decrease with the increase in zinc substitution. FTIR spectra of the Co_1−xZn_xFe₂O₄ with x varying from 0 to 1.0 in the range 400–4000 cm⁻¹ were reported. The spinel structure and the crystalline water adsorption of Co_1−xZn_xFe₂O₄ nanoparticles were studied by using FTIR.     

Magnetic properties on shape memory alloys Ni2Mn1+xIn1−x

X-ray powder diffraction and magnetization measurements were done on the magnetic shape memory alloys Ni₂Mn_1+xIn_1−x. On the basis of the results, the magnetic phase diagram was determined for Ni₂Mn_1+xIn_1−x alloys. Magnetization measurements make clear that the excess Mn atoms, which substitute for In sites, are coupled ferromagnetically to the ferromagnetic manganese sublattices. A magnetic phase diagram of Ni₂Mn_1+xIn_1−x alloys is discussed qualitatively on the basis of the interatomic dependence of the exchange interactions.     

BiFeO3/Zn1−xMnxO bilayered thin films

BiFeO₃/Zn_1−xMn_xO (x = 0-0.08) bilayered thin films were deposited on the SrRuO₃/Pt/TiO₂/SiO₂/Si(1 0 0) substrates by radio frequency sputtering. A highly (1 1 0) orientation was induced for BiFeO₃/Zn_1−xMn_xO. BiFeO₃/Zn_1−xMn_xO thin films demonstrate diode-like and resistive hysteresis behavior. A remanent polarization in the range of 2P_r ∼ 121.0-130.6 μC/cm² was measured for BiFeO₃/Zn_1−xMn_xO. BiFeO₃/Zn_1−xMn_xO (x = 0.04) bilayer exhibits a highest M_s value of ∼15.2 emu/cm³, owing to the presence of the magnetic Zn_0.96Mn_0.04O layer with an enhanced M_s value.     

Structural characterization and magnetization of Mg0.7Zn0.3SmxFe2−xO4 ferrites

Mg_0.7Zn_0.3Sm_xFe_2−xO₄ ferrites were prepared by the solid-state reaction method and were characterized by X-ray diffraction and magnetization measurements. A single spinel phase was obtained in the range 0.00?x?0.03$0.00?x?0.03$. The lattice parameter was found to increase at x=0.01$x=0.01$ and then decreases up to x=0.03$x=0.03$, which may indicate a distortion in the spinel lattice. The saturation magnetization was found to decrease with the increase in x up to 0.04, due to the replacement of the Fe³⁺ ions by the Sm³⁺ ions.     

Magnetoresistive properties of Zn1−xCoxFe2O4 ferrites

The magnetic and magnetoresistive properties of spinel-type Zn_1−xCo_xFe₂O₄ (x=0, 0.2 and 0.4) ferrites are extensively investigated in this study. A large negative magnetoresistance (MR) effect is observed in Zn_1−xCo_xFe₂O₄ ferrites of spinel structure. These materials are either ferrimagnetic or paramagnetic at room temperature, and show a spin-(cluster) glass transition at low temperatures, depending on the chemical compositions. The MR curves as a function of magnetic fields, MR(H), are parabolic at all temperatures for paramagnetic polycrystalline ZnFe₂O₄. The MR for ZnFe₂O₄ at 110 K in the presence of 9 T applied magnetic field is 30%. On the other hand, MR(H) are linear for x=0.2 and 0.4 ferrimagnetic Zn_1−xCo_xFe₂O₄ samples up to 9 T. The MR effect is independent of the sintering temperatures, and can be explained with the help of the spin-dependent scattering and the Yafet–Kittel angle of Zn_1−xCo_xFe₂O₄ mixed ferrites.     

Study of magnetic properties of Mn1−xCuxCr2S4 by: High-temperature series expansions

The high-temperature series expansions method applied in the systems Mn_1−xCu_xCr₂S₄ in the range 0?x?1. The exchange interactions and the magnetic exchange energies are calculated by using the probability law. The high-temperature series expansions have been applied in the spinel Mn_1−xCu_xCr₂S₄ systems, combined with the Padé approximants method, to determine the magnetic phase diagram, i.e. T_C versus dilution x. The critical exponent associated with the magnetic susceptibility (γ) is deduced. The obtained value of γ is insensitive to the dilution ratio x and may be compared with other theoretical results based on 3D Heisenberg model.     

Enhancement of initial permeability due to Mn substitution in polycrystalline Ni0.50−xMnxZn0.50Fe2O4

The structural and magnetic properties of Mn substituted Ni_0.50−xMn_xZn_0.50Fe₂O₄ (where x=0.00, 0.10 and 0.20) sintered at various temperatures have been investigated thoroughly. The lattice parameter, average grain size and initial permeability increase with Mn substitution. Both bulk density and initial permeability increase with increasing sintering temperature from 1250 to 1300 °C and above 1300 °C they decrease. The Ni_0.30Mn_0.20Zn_0.50Fe₂O₄ sintered at 1300 °C shows the highest relative quality factor and highest initial permeability among the studied samples. The initial permeability strongly depends on average grain size and intragranular porosity. From the magnetization as a function of applied magnetic field, M(H), it is clear that at room temperature all samples are in ferrimagnetic state. The number of Bohr magneton, n(μ_B), and Neel temperature, T_N, decrease with increasing Mn substitution. It is found that Mn substitution in Ni_0.50−xMn_xZn_0.50Fe₂O₄ (where x=0.20) decreases the Neel temperature by 25% but increases the initial permeability by 76%. Possible explanation for the observed characteristics of microstructure, initial permeability, DC magnetization and Neel temperature of the studied samples are discussed.     

X-ray absorption spectroscopic and magnetic characterization of cobalt-doped zinc oxide nanocrystals prepared by the molten-salt method

The local atomic arrangement and electronic structure of the Co-doped Zn_1−xCo_xO nanocrystal have been quantitatively examined along with its magnetic properties. According to our analysis using powder X-ray diffraction, electron microscopy, and Zn K-edge X-ray absorption spectroscopy (XAS), phase-pure wurzite-structured Zn_1−xCo_xO nanocrystals have been successfully synthesized via the molten-salt method. The Co K-edge XAS analysis clearly demonstrates that all the Co²⁺ ions are substituted for the tetrahedral Zn sites of the Wurzite structure with a coordination number of 3.9 and a bond distance of 1.97 Å, ruling out the presence of magnetic impurity phase and Co-metal cluster. Magnetization measurements reveal that the present Zn_1−xCo_xO sample does not show any ferromagnetic transition down to 2 K. In this regard, we can conclude that Co-doped zinc oxide is not ferromagnetic but the previously reported ferromagnetism in this phase would be an extrinsic property.     

Jahn-Teller transition in Al doped LiMn2O4 spinel

Al-doped lithium manganese spinels, with starting composition Li_1.02Al_xMn_1.98−xO₄ (0.00<x≤0.06), are investigated to determine the influence of the Al³⁺ doping on the Jahn-Teller (J-T) cooperative transition temperature T_J-T. X-ray powder diffraction (XRPD), nuclear magnetic resonance, electron paramagnetic resonance, conductivity and magnetic susceptibility data are put into relation with the tetrahedral and octahedral occupancy fraction of the spinel sites and with the homogeneous distribution of the Al³⁺ ions in the spinel phase. It is observed that Al³⁺ may distribute between the two cationic sublattices. The J-T distortion, associated with a drop of conductivity near room temperature in the undoped sample, is shifted towards lower temperature by very low substitution. However, for x>0.04 T_J-T it increases with increasing x, as clearly evidenced in low temperature XRPD observations. A charge distribution model in the cationic sublattice, for Al substitution, is proposed to explain this peculiar behavior.     

Optical properties of bulk Zn1−xCoxO magnetic semiconductors

Polycrystalline Zn_1−xCo_xO (x=0, 0.02, 0.05, 0.10 and 0.15) oxides have been synthesized by solid state reaction via sintering ZnO and Co powders in open air. X-ray diffraction analyses using Rietveld refinement indicate that a stoichiometric single phase with a wurtzite-like structure was found in Zn_1−xCo_xO samples with x up to 0.10. The elemental mapping using energy dispersive X-ray spectroscopic analyses presents a uniform distribution of Co. Optical transmittance measurements show that several extra absorption bands appear in the Co-doped ZnO, which is due to the transitions between the crystal-field-split 3d levels of tetrahedral Co²⁺ substituting Zn²⁺ ions. Raman measurements show that limited host lattice defects are induced by Co doping. Magnetization measurements reveal that the Co-doped ZnO samples are paramagnetic due to the absence of free carriers and in low temperature the dominant magnetic interaction is nearest-neighbor antiferromagnetic.     

Synthesis and investigation of magnetic properties of substituted ferrite nanoparticles of spinel system Mn1−xZnx[Fe2−yLy]O4

Superparamagnetic nanoparticles of the spinel ferrite four-element system Mn_1−xZn_x[Fe_2−yL_y]O₄ (where L:Gd³⁺, La³⁺, Ce³⁺, Eu³⁺, Dy³⁺, Er³⁺,Yb³⁺) were synthesized by the co-precipitation method. The magnetic moments of the 10 nm diameter nanoparticles were comparable to the ones of Fe₃O₄ nanoparticles. A comparatively low T_C (∼52–72 °C) was observed for some of the compositions. The heating mechanism of the superparamagnetic particles in the AC magnetic field at radiofrequency range is discussed and especially the absence of the hysteresis loop in the M–H curve at room temperature. One possible explanation—spontaneous particle agglomeration—was experimentally verified.     

No room temperature ferromagnetism in Mn over-doped Zn1−xMnxO (x>0.02)

Mn-doped ZnO samples having composition Zn_1−xMn_xO (x=0.02, 0.04 and 0.05) were synthesized by solid state reaction technique with varying concentration of Mn from 0.02 to 0.05. Evidence of room temperature ferromagnetism was observed only in the composition Zn_0.98Mn_0.02O sintered at 500 °C. Our XRD pattern confirms the presence of Mn₃O₄ impurity phase in all the Zn_1−xMn_xO samples with the exception of Zn_0.98Mn_0.02O. We emphasize that the appearance of Mn₃O₄ phase in the system forbids the exchange type of interaction between the Mn ions and suppresses the ferromagnetism in all the Mn over-doped Zn_1−xMn_xO (x>0.02) system. SEM microstructure study also supports the interruption of exchange type of interaction inside the system with the increase in Mn concentration in the sample. Interestingly, for this particular composition, Zn_0.98Mn_0.02O sintered at 500 °C, glassy ferromagnetism type of transition is observed at low temperature. This type of transition is attributed to the formation of the oxides of Mn clusters at low temperature.     

Room-temperature ferromagnetism in Sn1−xMnxO2 nanocrystalline thin films prepared by ultrasonic spray pyrolysis

Sn_1−xMn_xO₂ (x=0.01-0.05) thin films were synthesized on quartz substrate using an inexpensive ultrasonic spray pyrolysis technique. The influence of doping concentration and substrate temperature on structural and magnetic properties of Sn_1−xMn_xO₂ thin films was systematically investigated. X-ray diffraction (XRD) studies of these films reflect that the Mn³⁺ ions have substituted Sn⁴⁺ ions without changing the tetragonal rutile structure of pure SnO₂. A linear increase in c-axis lattice constant has been observed with corresponding increase in Mn concentration. No impurity phase was detected in XRD patterns even after doping 5 at% of Mn. A systematic change in magnetic behavior from ferromagnetic to paramagnetic was observed with increase in substrate temperature from 500 to 700 °C for Sn_1−xMn_xO₂ (x=0.01) films. Magnetic studies reveal room-temperature ferromagnetism (RTFM) with 3.61×10⁻⁴ emu saturation magnetization and 92 Oe coercivity in case of Sn_1−xMn_xO₂ (x=0.01) films deposited at 500 °C. However, paramagnetic behavior was observed for the films deposited at a higher substrate temperature of 700 °C. The presence of room-temperature ferromagnetism in these films was observed to have an intrinsic origin and could be obtained by controlling the substrate temperature and Mn doping concentration.     

Effect of oxygen annealing on the Mn properties in ZnMnO Films

We studied the influence of thermal annealing in oxygen on the physical properties of MOCVD grown Zn_1−xMn_xO thin layers. Annealing in the 300–1000 °C temperature range modifies both lattice parameters and magnetic properties of the layers. Correlation of the results from X-ray diffraction, EPR studies and Raman spectroscopy indicate a modification of the Mn⁺²-related features in the ZnO matrix.     

Influence of annealing temperature on structural, optical and magnetic properties of Mn-doped ZnO thin films prepared by sol-gel method

Thin films of Zn_1−xMn_xO (x=0.01) diluted magnetic semiconductor were prepared on Si (1 0 0) substrates by the sol-gel method. The influence of annealing temperature on the structural, optical and magnetic properties was studied by X-ray diffraction (XRD), atom force microscopy (AFM), photoluminescence (PL) and SQUID magnetometer (MPMS, Quantum Design). The XRD spectrum shows that all the films are single crystalline with (0 0 2) preferential orientation along c-axis, indicating there are not any secondary phases. The atomic force microscopy images show the surfaces morphologies change greatly with an increase in annealing temperature. PL spectra reveal that the films marginally shift the near band-edge (NBE) position due to stress. The magnetic measurements of the films using SQUID clearly indicate the room temperature ferromagnetic behavior, and the Curie temperature of the samples is above room temperature. X-ray photoelectron spectroscopy (XPS) patterns suggest that Mn²⁺ ions were successfully incorporated into the lattice position of Zn²⁺ ions in ZnO host. It is also found that the post-annealing treatment can affect the ferromagnetic behavior of the films effectively.     

Magnetic properties of electron-doped Y1−xCexMnO3 compounds

Cerium-doped Y_1−xCe_xMnO₃ compounds have been prepared in single-phase form for x=0 to 0.10. X-ray diffraction (XRD) patterns could be analyzed by using P6₃cm space group. Temperature variations of ac susceptibility and magnetization measurements show that these Ce-doped materials exhibit weak ferromagnetic transition. The observed ferromagnetic transition is attributed to the double exchange ferromagnetic interaction between Mn²⁺ and Mn³⁺ ions due to electron doping. The M–H loops exhibit hysteresis along with linear contribution and were analyzed based on bound magnetic polaron (BMP) model. Increase in saturation magnetization and decrease in BMP concentrations have been observed with increase in Ce doping.