Granular L10 FePt (0 0 1) thin films for Heat Assisted Magnetic Recording

Granular L1₀ FePt (0 0 1) thin films were deposited on a Si substrate with Ta/MgO underlayers by rf sputtering. The effects of in-situ heating temperatures (350-575 °C), pressures (2-40 mTorr), and sputtering powers (15-75 W) on texture and microstructure were investigated for the FePt films. We obtained films with grain densities approaching 50 teragrains per in.², grains sizes down to 2.2 nm with center-to-center spacing of 4.2 nm and coercivity of 24 kOe. The order parameters for the L1₀ FePt thin films were derived and calculated to be as high as 0.91. Although the grain size is small, the spacing between grains is too large for practical heat assisted magnetic recording media. To reach the desired results, we propose that layer-by-layer growth should be promoted in the FePt layer by inserting another underlayer that provides a better lattice match to L1₀ FePt.     

Theoretical study of magnetism and electronic structure of Fe3/Crn(1 1 0) superlattices

The electronic structure and magnetism of Fe₃/Cr_n(1 1 0) (n=1, 3, 5) superlattices (SL) with varying layer thickness have been studied using the full-potential linearized augmented plane-wave (FLAPW) method within the first-principle formalism. The results show that the ferromagnetic state is the preferable phase in the ground state. The magnetic moments of the Fe layers are slightly modified by the presence of the Cr layers. The Cr magnetic moments alternate direction from layer to layer, and an antiferromagnetic coupling between Fe and Cr at the interfacial layer is seen. The magnetic moments of the Cr layers are suppressed because there is a strong hybridization between d-states of both Fe and Cr atoms. Only a small moment is found in the Cr layer. The Cr moment alignment is determined by a delicate balance between the different magnetic interaction.     

Effect of crystallinity of Co layer on perpendicular exchange bias in Au-capped ultrathin Co film on Cr2O3(0 0 0 1) thin film

The effect of the crystalline quality of ultrathin Co films on perpendicular exchange bias (PEB) has been investigated using a Au/Co/Au/α-Cr₂O₃ thin film grown on a Ag-buffered Si(1 1 1) substrate. Our investigation is based on the effect of the Au spacer layer on the crystalline quality of the Co layer and the resultant changes in PEB. An α-Cr₂O₃(0 0 0 1)layer is fabricated by the thermal oxidization of a Cr(1 1 0) thin film. The structural properties of the α-Cr₂O₃(0 0 0 1) layer including the cross-sectional structure, lattice parameters, and valence state have been investigated. The fabricated α-Cr₂O₃(0 0 0 1) layer contains twin domains and has slightly smaller lattice parametersthan those of bulk-Cr₂O₃. The valence state of the Cr₂O₃(0 0 0 1) layer is similar to that of bulk Cr₂O₃. The ultrathin Co film directly grown on the α-Cr₂O₃(0 0 0 1) deposited by an e-beam evaporator is polycrystalline. The insertion of a Au spacer layer with a thickness below 0.5 nm improves the crystalline quality of Co, probably resulting in hcp-Co(0 0 0 1). Perpendicular magnetic anisotropy (PMA) appears below the Néel temperature of Cr₂O₃ for all the investigated films. Although the PMA appears independently of the crystallinequality of Co, PEB is affected by the crystalline quality of Co. For the polycrystalline Co film, PEB is low, however, a high PEB is observed for the Co films whose in-plane atom arrangement is identical to that of Cr³⁺ in Cr₂O₃(0 0 0 1). The results are qualitatively discussed on the basis of the direct exchange coupling between Cr and Co at the interface as the dominant coupling mechanism.     

Effect of Cr100−xTix (x = 0-19 at.%) alloy underlayers on the high coercivity of FePt thin film below the substrate temperature of 250 °C

The effect of Cr_100−xTi_x underlayer on orderd-L1₀ FePt films was investigated. A low-temperature ordering of FePt films could be attained through changing the Ti content of Cr_100−xTi_x underlayer. The ordering temperature of the 30 nm FePt film grown on 20 nm Cr₉₀Ti₁₀ underlayer was reduced to 250 °C which is practical manufacture process temperature. An in-plane coercivity was very high to 6000 Oe and a ratio of remnant magnetization (M_r) to saturation magnetization (M_s) was as large as 0.85. This result indicates that the coercivity obtained at 250 °C by the effect of CrTi underlayer is significantly higher than those obtained at 250-275 °C by the effect of underlayers in other conventional studies. The prominent improvement of the magnetic properties of ordered FePt thin films at low temperature of 250 °C could be understood with considering the strain-induced ordering phase transformation associated with lattice mismatch between Cr underlayer and FePt magnetic layer due to an addition of Ti content.     

Epitaxial growth of Co(0 0 0 1)hcp/Fe(1 1 0)bcc magnetic bi-layer films on SrTiO3(1 1 1) substrates

Co(0 0 0 1)_hcp/Fe(1 1 0)_bcc epitaxial magnetic bi-layer films were successfully prepared on SrTiO₃(1 1 1) substrates. The crystallographic properties of Co/Fe epitaxial magnetic bi-layer films were investigated. Fe(1 1 0)_bcc soft magnetic layer grew epitaxially on SrTiO₃(1 1 1) substrate with two type variants, Nishiyama–Wasserman and Kurdjumov–Sachs relationships. An hcp-Co single-crystal layer is obtained on Ru(0 0 0 1)_hcp interlayer, while hcp-Co layer formed on Au(1 1 1)_fcc or Ag(1 1 1)_fcc interlayer is strained and may involve fcc-Co phase. It has been shown possible to prepare Co/Fe epitaxial magnetic bi-layer films which can be usable for patterned media application.     

The magnetic map of NiMn alloy thin films on Co(0 0 1) and Co(1 1 1)

Following the experimental work of Groudeva-Zotova et al. [S. Groudeva-Zotova, D. Elefant, R. Kaltofen, D. Tietjen, J. Thomas, V. Hoffmann, C.M. Schneider, J. Magn. Magn. Mater. 263 (2003) 57] where the magnetic and structural characteristics of a bi-layer NiMn-Co exchange biasing systems was investigated, density functional calculations with generalized gradient corrections were performed on (Mn_0.5Ni_0.5)_n ordered alloy on Co(0 0 1) and one Mn_1−xNi_x monolayer on Co(1 1 1). For the Mn_0.5Ni_0.5 monolayer on Co(0 0 1), magnetic moments per surface atom of 0.65 μ_B and 3.76 μ_B were obtained for Ni and Mn, respectively. Those magnetic moments are aligned parallel to the total moment of Co(0 0 1). A complex behavior of the Mn moment in dependence of the thickness “n” is obtained for (Mn_0.5Ni_0.5)_n on Co(0 0 1). Investigations on Mn_1−xNi_x monolayer on Co(1 1 1) have shown that the crystallographic orientation does not modify significantly neither the magnetic moments of Mn and Ni atoms nor their ferromagnetic coupling with the Co(1 1 1) substrate, except for x = 0.66. For x = 0.66 the Mn sub-lattice presents an antiferromagnetic coupling leading to a quenching of the Ni magnetic moment.     

Control of crystallographic orientation in L10 FePt films by using Cr and CrW underlayers

The microstructure and magnetic properties of FePt films grown on Cr and CrW underlayers were investigated. The FePt films that deposited on Cr underlayer show (2 0 0) orientation and low coercivity because of the diffusion between FePt and Cr underlayer. The misfit between FePt magnetic layer and underlayer increases by small addition of W element in Cr underlayer or using a thin Mo intermediate layer, which is favorable for the formation of (0 0 1) orientation and the transformation of FePt from fcc to fct phase. A good FePt (0 0 1) texture was obtained in the films with Cr₈₅W₁₅ underlayer with substrate temperature of 400 °C. The FePt films deposited on Mo/Cr underlayer exhibit larger coercivity than that of the films grown on Pt/Cr₈₅W₁₅ because 5 nm Mo intermediate layer depressed the diffusion of Cr into magnetic layer.     

Exchange interaction effect of TbCo/FePt bilayers

Interlayer exchange coupling in dc-magnetron sputtered Tb_29.6Co_70.4/FePt bilayers with different annealing temperatures of the FePt film have been investigated. The dependence of ordering degree on perpendicular magnetic properties of the FePt film was studied. The Tb_29.6Co_70.4/FePt film has high perpendicular coercivity and high saturated magnetization about 7.5 kOe, and 302 emu/cm³, respectively as the substrate temperature is 500 °C and annealing at 500 °C for 30 min. It also shows a strong exchange coupling between this FePt layer and Tb_29.6Co_70.4 layer. We also examined the interface wall energy in the exchange coupled Tb_29.6Co_70.4/FePt double layers.     

Exchange bias in (1 1 0)-orientated Bi0.9La0.1FeO3/La0.5Ca0.5MnO3 films

We performed a systematic study on the exchange bias in (1 1 0)-orientated Bi_0.9La_0.1FeO₃/La_0.5Ca_0.5MnO₃ (BLFO/LCMO) heterostructure with a fixed BLFO film thickness of 600 nm and different LCMO layers ranging from t=0 to 30 nm. The LCMO is found to be weakly ferromagnetic, with the Curie temperature descending from ∼225 K to 0 as the layer thickness decreases from 30 nm to 3 nm. The main magnetic contributions come from the BLFO film, and the areal magnetization ratio is 1:0.07 for t=5 nm and 1:0.82 for t=30 nm for BLFO to LCMO at the temperature of 5 K. Further experiments show the presence of significant exchange bias, and it is, at the temperature of 10 K, ∼40 Oe for t=0 and ∼260 Oe for t=30 nm. The exchange bias reduces dramatically upon warming and disappears above the blocking temperature of the spin-glasslike behavior observed in the samples. The possible origin for exchange bias is discussed.     

Low-temperature deposition of L10 FePt films for ultra-high density magnetic recording

A method based on strain-induced phase transformation was used to lower the ordering temperature of FePt films. The strain resulted from the lattice mismatch between the FePt film and the substrate or underlayer favored the ordering. The relationships between the lattice mismatch, the ordering of FePt film, and the corresponding magnetic anisotropic constant were investigated. A critical lattice mismatch near 6.33% was believed to be most suitable for improving the chemical ordering of the FePt films. CrX (X=Ru, Mo, W, Ti) alloys with (2 0 0) texture was used to control the easy axis and ordering temperature of FePt films on glass substrate. Large uniaxial anisotropy constant K_u?1×10⁷ erg/cm³, good magnetic squareness (∼1) and FePt(0 0 1) texture (rocking curve −5°) were obtained at the temperature T_s?250 °C when using CrRu underlayer. The diffusion from overlying layers of Ag and Cu and an inserted Ag pinning layer were effective in reducing the exchange decoupling and changing the magnetization reversal. The media noise was effectively reduced and the SNR was remarkably enhanced when a 2 nm Ag was inserted.     

Effects of Cr underlayer and Pt buffer layer on the interfacial structure and magnetic characteristics of sputtered FePt films

This work develops a new method for growing L1₀ FePt(0 0 1) thin film on a Pt/Cr bilayer using an amorphous glass substrate. Semi-coherent epitaxial growth was initiated from the Cr(0 0 2) underlayer, continued through the Pt(0 0 1) buffer layer, and extended into the L1₀ FePt(0 0 1) magnetic layer. The squareness of the L1₀ FePt film in the presence of both a Cr underlayer and a Pt buffer layer was close to unity as the magnetic field was applied perpendicular to the film plane. The single L1₀ FePt(1 1 1) orientation was observed in the absence of a Cr underlayer. When a Cr underlayer is inserted, the preferred orientation switched from L1₀ FePt(1 1 1) to L1₀ FePt(0 0 1) and the magnetic film exhibited perpendicular magnetic anisotropy. However, in the absence of an Pt intermediate layer, the Cr atoms diffused directly into the FePt magnetic layer and prevented the formation of the L1₀ FePt(0 0 1) preferred orientation. When a Pt buffer layer was introduced between the FePt and Cr underlayer, the L1₀ FePt(0 0 1) peak appeared. The thickness of the Pt buffer layer also substantially affected the magnetic properties and atomic arrangement at the FePt/Pt and Pt/Cr interfaces.     

Structural and magnetic properties of RF sputtered FePt/Fe multilayers

Series of [FePt(4min)/Fe(t_Fe)]₁₀ multilayers have been prepared by RF magnetron sputtering and post-annealing in order to optimize their magnetic properties by structural designs. The structure, surface morphology, composition and magnetic properties of the deposited films have been characterized by X-ray diffractometer (XRD), Rutherford backscattering (RBS), scanning electron microscope (SEM), energy dispersive X-ray spectroscope (EDX) and vibrating sample magnetometer (VSM). It is found that after annealing at temperatures above 500 °C, FePt phase undergoes a phase transition from disordered FCC to ordered FCT structure, and becomes a hard magnetic phase. X-ray diffraction studies on the series of [FePt/Fe]_n multilayer with varying Fe layer thickness annealed at 500 and 600 °C show that lattice constants change with Fe layer thickness and annealing temperature. Both lattice constants a and c are smaller than those of standard ones, and lattice constant a decreases as Fe layer deposition time increases. Only a slight increase in grain size was observed as Fe layer decreased in samples annealed at 500 °C. However, the increase in grain size is large in samples annealed at 600 °C. The coercivities of [FePt/Fe]_n multilayers decrease with Fe layer deposition time, and the energy product (BH)_max reaches a maximum in the samples with Fe layer deposition time of 3 min. Comparison of magnetic properties with structure showed an almost linear relationship between the lattice constant a and the coercivities of the FePt phase.     

NMR of Xe on CO/Ir(1 1 1) and on multilayer Xe/Ir(1 1 1)

Nuclear magnetic resonance (NMR) is performed on monolayer (ML) amounts of adsorbed ¹²⁹Xe on a single crystal substrate. The inherently low sensitivity of NMR is overcome by using highly nuclear spin polarized ¹²⁹Xe that has been produced by optical pumping. A polarization of 0.8 is regularly achieved which is 10⁵ times the thermal (Boltzmann) polarization. The experiments are performed with a constant flux of xenon atoms impinging on the surface, typically 4 ML/s. The chemical shift (σ) of ¹²⁹Xe is highly sensitive to the Xe local environment. We measured profoundly different shifts for the Xe bulk, for the surface of the Xe bulk, and for Xe on CO/Ir(1 1 1). The growth of the bulk is seen in a phase transition like change of σ as a function of temperature at constant Xe flux. At temperatures where no bulk forms at a flux of 4 ML/s, the xenon exchange rate was measured by a spin inversion/recovery method. The exchange time of Xe is found to be 0.24 s at 63.4 K and 64.4 K and somewhat longer at 61.2 K. An analysis is given involving the desorption out of the second layer and fast mixing of first and second layer atoms at these temperatures.     

Spin-engineering in the Co75Fe25/Cu(1 1 0) system

We present results on the growth and magnetic anisotropies of Co₇₅Fe₂₅ films grown on a Cu(1 1 0) single crystal. Angular dependent MOKE measurements show a thickness dependent, in-plane rotation of the easy axis of magnetisation of up to 60° from the [0 0 1] direction (towards [−1 1 0]). For a film thickness of 5 ML, just greater than that required for the onset of ferromagnetism, uniaxial anisotropy is observed with the easy axis along the [0 0 1] direction. As the film thickness increases this is seen to rotate in-plane towards the [−1 1 0] direction as the contribution from the cubic anisotropy constant grows. At a film thickness of 9 ML there is predominantly cubic anisotropy and at 10 ML the easy axis is rotated to 150° with respect to the [1 −1 0] axis, where it is stabilised.     

Fourfold in-plane magnetic anisotropy in epitaxial Fe(1 1 0)/Cu(0 0 1) and Fe(1 1 0)/Ni(0 0 1) bilayers

Epitaxial Fe(1 1 0) films with thicknesses of 100-800 nm on Cu(0 0 1) and Ni(0 0 1) buffer layers grown on MgO(0 0 1) substrates have been fabricated. These films contain Fe(1 1 0) crystallites which are in the Pitsch orientation relationship. Magnetization and the fourfold in-plane magnetic anisotropy constants of these films have been determined by torque measurements. All the samples under study are characterized by a fourfold magnetic anisotropy with easy axes parallel to the [1 0 0] and [0 1 0] directions of Cu(0 0 1) and Ni(0 0 1) layers. The measured values of the constant for Fe(1 1 0)/Cu(0 0 1) are found to depend on deposition temperature; a maximum value of (2.5±0.1)×10⁵ erg/cm³ is reached after annealing at 600 °С. The in-plane torque measurements on Fe(1 1 0)/Ni(0 0 1) bilayers obtained at 300 °С, on the other hand, exhibit a constant value of (2.7±0.1)×10⁵ erg/cm³. Assuming an exchange interaction between the Fe(1 1 0) crystallites, which are in the Pitsch orientation relationship, the fourfold in-plane magnetic anisotropy has been calculated as 2.8×10⁵ erg/cm³. The deviations of the experimental values from the predicted one may be explained by the formation of a polycrystalline phase within the Fe(1 1 0) layer and a partial disorientation of the epitaxial crystallites.     

CF interaction with Si(1 0 0)-(2 × 1): Molecular dynamics simulation

In this study, the interaction of CF with the clean Si(1 0 0)-(2 × 1) surface at normal incidence and room temperature was investigated using molecular dynamics simulation. Incident energies of 2, 12 and 50 eV were simulated. C atoms, arising from dissociation, preferentially react with Si to form Si-C bonds. A Si_xC_yF_z interfacial layer is formed, but no etching is observed. The interfacial layer thickness increases with increasing incident energy, mainly through enhanced penetration of the silicon lattice. Silicon carbide and fluorosilyl species are formed at 50 eV, which is in good agreement with available experimental data. The level of agreement between the simulated and experimental results is discussed.     

Magnetic ordering of Vn/Mo(0 0 1) systems: Ab-initio calculations

A density-functional theory (DFT) study is performed using a full-potential linearized-augmented-plane-waves (FP-LAPW) method to investigate the magnetic structure of vanadium-molybdenum systems (V_n/Mo(0 0 1), n = 1, 2). The topmost V layers relax inward in both systems with a larger contraction in V₂/Mo(0 0 1) system. A p(1 × 1) in-plane ferromagnetic ordering with appreciable magnetic moments is obtained on V overlayers, which is found to be the ground state in both systems. The layers below the surface exhibit induced magnetism with antiferromagnetic interlayer coupling.     

Microstructure and magnetic properties of FePt:Ag nanocomposite films on SiO2/Si(1 0 0)

FePt:Ag nanocomposite films were prepared by pulsed filtered vacuum arc deposition system and subsequent rapid thermal annealing on SiO₂/Si(1 0 0) substrates. The microstructure and magnetic properties were investigated. A strong dependence of coercivity and ordering of the face-central tetragonal structure on both Ag concentration and annealing temperature was observed. With Ag concentration of 22% in atomic ratio, the coercivity got to 6.0 kOe with a grain size of 6.7 nm when annealing temperature was 400 °C.     

Role of crystal orientation on the magnetic properties of CoFe2O4 thin films grown on Si (1 0 0) and Al2O3 (0 0 0 1) substrates using pulsed laser deposition

We report the influence of crystal orientation on the magnetic properties of CoFe₂O₄ (CFO) thin films grown on single crystal Si (1 0 0) and c-cut sapphire (Al₂O₃) (0 0 0 1) substrates using pulsed laser deposition technique. The thickness was varied from 200 to 50 nm for CFO films grown on Si substrates, while it was fixed at 200 nm for CFO films grown on Al₂O₃ substrates. We observed that the 200 and 100 nm thick CFO-Si films grew in both (1 1 1) and (3 1 1) directions and displayed out-of-plane anisotropy, whereas the 50 nm thick CFO-Si film showed only an (1 1 1) orientation and an in-plane anisotropy. The 200 nm thick CFO film grown on an Al₂O₃ substrate was also found to show a complete (1 1 1) orientation and a strong in-plane anisotropy. These observations pointed to a definite relation between the crystalline orientation and the observed magnetic anisotropy in the CFO thin films.     

Signatures of epitaxial graphene grown on Si-terminated 6H-SiC (0 0 0 1)

Epitaxial graphene layers thermally grown on Si-terminated 6H-SiC (0 0 0 1) have been probed using Auger electron spectroscopy, Raman microspectroscopy, and scanning tunneling microscopy (STM). The average multilayer graphene thickness is determined by attenuation of the Si (L₂₃VV) and C (KVV) Auger electron signals. Systematic changes in the Raman spectra are observed as the film thickness increases from one to three layers. The most striking observation is a large increase in the intensity of the Raman 2D-band (overtone of the D-band and also known as the G′-band) for samples with a mean thickness of more than ∼1.5 graphene layers. Correlating this information with STM images, we show that the first graphene layer imaged by STM produces very little 2D intensity, but the second imaged layer shows a single-Lorentzian 2D peak near 2750 cm⁻¹, similar to spectra acquired from single-layer micromechanically cleaved graphene (CG). The 4-10 cm⁻¹ higher frequency shift of the G peak relative to CG can be associated with charge exchange with the underlying SiC substrate and the formation of finite size domains of graphene. The much greater (41-50 cm⁻¹) blue shift observed for the 2D-band may be correlated with these domains and compressive strain.