Growth of GaAs/AlGaAs HBTs by MOMBE (CBE)

In this paper, we will discuss how the unique growth chemistry of MOMBE can be used to produce high speed GaAs/AlGaAs heterojunction bipolar transistors (HBTs). The ability to grow heavily doped, well-confined layers with carbon doping from trimethylgallium (TMG) is a significant advantage for this device. However, in addition to high p-type doping, high n-type doping is also required. While elemental Sn can be used to achieve doping levels up to 1.5×10¹⁹ cm^-3, severe segregation limits its use to surface contact layers. With tetraethyltin (TESn), however, segregation does not occur and Sn doping can be used throughout the device. Using these sources along with triethylgallium (TEG), trimethylamine alane (TMAA), and AsH₃, we have fabricated Npn devices with 2 μm×10 μm emitter stripes which show gains of ≥ 20 with either ƒ_t = 55 GHz and ƒ_max = 70 GHz or ƒ_t = 70 GHz and ƒ_max = 50 GHz, depending upon the structure. These are among the best RF values reported for carbon doped HBTs grown by any method, and are the first reported for an all-gas source MOMBE process. In addition, we have fabricated a 70 transistor decision circuit whose performance at 10 Gb/s equals or exceeds that of similar circuits made from other device technologies and growth methods. These are the first integrated circuits reported from MOMBE grown material.     

Heavily carbon-doped GaAs grown on various oriented GaAs substrates by MOMBE

Heavily carbon-doped GaAs epitaxial layers have been grown simultaneously on (100), (111)A, (111)B, (411)A, (411)B and (711)A semi-insulating (SI) GaAs substrates by metalorganic molecular beam epitaxy (MOMBE) using trimethylgallium (TMG) and elemental As (As₄). The hole concentration and surface flatness strongly depend on the substrate orientation. The highest carbon incorporation was observed for the layers grown on a (411)A substrate with a hole concentration of 1.0 × 10²¹ cm^{− 3} and a lattice mismatch of Δd/d = −0.48%. Atomic force microscope (AFM) images reveal that the epilayers grown on (411)A substrates exhibit extremely flat surfaces, although these layers contain the highest carbon concentration.     

Low temperature growth of AlGaAs by MOMBE (CBE) using trimethylamine alane

In order to gain further insight into the surface chemistry of AlGaAs growth by metalorganic molecular beam epitaxy, we have investigated the deposition behavior and material quality of AlGaAs grown at temperatures from 350 to 500°C using trimethylamine alane (TMAA), triethylgallium (TEG) and arsine (AsH₃). Though the Al incorporation rate decreases with decreasing temperature, Ga-alkyl pyrolysis, and hence Ga incorporation rate, declines more rapidly. Thus the Al content increases from X_AlAs = 0.25 at 500°C to X_AlAs = 0.57 at 350°C. Below 450°C, the Ga incorporation rate appears to be determined by the desorption of diethylgallium species, rather than interaction with adsorbed AlH₃. Similarly, carbon incorporation is enhanced by 2 orders of magnitude over this temperature range due to the increasingly inefficient pyrolysis of the Ga-C bond in TEG. Additionally, active hydrogen from the TMAA1, which normally is thought to getter the surface alkyls, is possibly less kinetically active at lower growth temperatures. Contrary to what has been observed in other growth methods, low growth temperatures produced a slight decrease in oxygen concentration. This effect is likely due to reduced interaction between Ga alkoxides (inherent in the TEG) and the atomic hydrogen blocked Al species on the growth surface. This reduction in oxygen content and increase in carbon concentration causes the room temperature PL intensity to actually increase as the temperature is reduced from 500 to 450°C. Surprisingly, the crystalline perfection as measured by ion channeling analysis is quite good, χ_min≤5%, even at growth temperatures as low as 400°C. At 350°C, the AlGaAs layers exhibit severe disorder. This disorder is indicative of insufficient Group III surface mobility, resulting in lattice site defects. The disorder also supports our conclusions of kinetically limited surface mobility of all active surface components.     

Hillock formation observed in MOMBE of InGaAs grown on a patterned GaAs substrate

We observed hillock formation during metalorganic molecular beam epitaxy (MOMBE) of InGaAs on a mesa-grooved (100) GaAs substrate. Hillocks were formed under specific growth conditions and comprised mostly InAs. The distribution of hillocks formed in InGaAs MOMBE using trimethylindium (TMIn) and metal Ga depended strongly on the widths of mesa-grooves; the density decreased with decreasing width and hillocks were hardly observed on the ridges. The hillock density also varied, depending on the off-angle of the substrate from the (100) plane. This indicates that the observed anomalous distribution of InGaAs hillocks was caused by both the formation of facets and a vicinal tilted surface near the edge of mesa-grooves, due to the growth of a GaAs buffer layer on a patterned substrate.     

AlGaAs/GaAs/AlGaAs quantum wells as a sensitive tool for the MOVPE reactor environment

We present in this work a simple quantum well (QW) structure consisting of GaAs wells with AlGaAs barriers as a probe for measuring the performance of arsine purifiers within a metalorganic vapour phase epitaxy system. Comparisons between two different commercially available purifiers are based on the analysis of low-temperature photoluminescence emission spectra from thick QWs, grown on GaAs substrates misoriented slightly from (1 0 0). Neutral excitons emitted from these structures show extremely narrow linewidths, comparable with those that can be obtained by molecular beam epitaxy in an ultra-high vacuum environment, suggesting that purifications well below the 1 ppb level are needed to achieve high quality quantum well growth.     

CBE growth of high-quality AlGaAs/GaAs heterostructures for HEMT applications

AlGaAs/GaAs heterostructures were grown by chemical beam epitaxy using triethylgallium, triisobutylaluminium and pure arsine in flow control mode with hydrogen as carrier gas. For substrate temperatures of 580°C and V/III ratios of 10, high quality AlGaAs layers are obtained; heterostructures show abrupt and smooth interfaces. Modulation doping with silicon evaporated from a conventional effusion cell gives two-dimensional electron gases with carrier densities up to 1×10¹² cm^-2. Mobilities of 70000 cm²/V·s are obtained at 77 K for carrier densities of 4×10¹¹ cm^-2. The lateral homogeneity of the heterostructures in layer thickness, composition and doping level is excellent. Perfect morphology with defect densities of about 100 cm^-2 is observed. High electron mobility transistors (gate length 0.3 nm) fabricated from quantum well structures show a transconductance of about 380 mS/mm.     

A difference between initial growth stages of the AlGaAs/GaAs and GaAs/AlGaAs heterostructures produced by contact replacement of solutions

The method of liquid epitaxial growth of GaAs/AlGaAs/GaAs heterostructures when the change of solutions occurs due to pushing off one melt by another is discussed. It has been shown theoretically and experimentally that the initial stages of film growth after the change of the binary Ga As melt on the ternary Al Ga As melt differ from that when the Ga As solution pushes off the Al Ga As liquid. The difference is caused by the inequality of the diffusion coefficients of As and Al in a multicomponent Al Ga As liquid (D_Al > D_As). As a result, the growth of an AlGaAs film begins immediately in the case when the Al Ga As solution pushes off the Ga As liquid but in the opposite case the dissolution of an underlying AlGaAs solid is unavoidable and depends little on degree of a saturation of the Ga As washing solution. These peculiarities must be taken into account in discussions of abruptness and other properties of LPE-grown AlGaAs/GaAs and GaAs/AlGaAs heterojunctions.     

Fabrication and characterization of GaAs quantum well buried in AlGaAs/GaAs heterostructure nanowires

We developed a growth method for forming a GaAs quantum well contained in an AlGaAs/GaAs heterostructure nanowire using selective-area metal organic vapor phase epitaxy. To find the optimum growth condition of AlGaAs nanowires, we changed the growth temperature between 800 and 850 °C and found that best uniformity of the shape and the size was obtained near 800 °C but lateral growth of AlGaAs became larger, which resulted in a wide GaAs quantum well grown on the top (1 1 1)B facet of the AlGaAs nanowire. To form the GaAs quantum well with a reduced lateral size atop the AlGaAs nanowire, a GaAs core nanowire about 100 nm in diameter was grown before the AlGaAs growth, which reduced the lateral size of AlGaAs to roughly half compared with that without the GaAs core. Photoluminescence measurement at 4.2 K indicated spectral peaks of the GaAs quantum wells about 60 meV higher than the acceptor-related recombination emission peak of GaAs near 1.5 eV. The photoluminescence peak energy showed a blue shift of about 15 meV, from 1.546 to 1.560 eV, as the growth time of the GaAs quantum well was decreased from 8 to 3 s. Transmission electron microscopy and energy dispersive X-ray analysis of an AlGaAs/GaAs heterostructure nanowire indicated a GaAs quantum well with a thickness of 5−20 nm buried along the 〈1 1 1〉 direction between the AlGaAs shells, showing a successful fabrication of the GaAs quantum well.     

The Back-Side Morphology of LPE-Grown AlGaAs/GaAs/AlGaAs Heterostructures after the Complete Removal of the GaAs Substrate by Selective Etching

As-grown surfaces of AlGaAs/GaAs/AlGaAs heterostructures were stuck down the glass disks and after that the GaAs substrates were removed completely by selective chemical etching. As a result the back-surface of the heterostructures became open to light. The influence of different factors on the back-surface planarity and on the density of such specific defects as holes in the GaAs layer have been investigated. It is shown that the density of holes can be decreased to a value less than 1 hole/cm² if a glove-box maintained under a pure N₂ atmosphere and connected with LPE installation is used.     

The transition layers in AlGaAs/GaAs and InGaAsP/GaAs heterostructures grown by LPE

AlGaAs/GaAs and InGaAsP/GaAs heterostructues were grown by liquid phase epitaxy (T_o = 800–770 °C), the transition layers (TLs) were measured with Auger profiling. The Auger profiling of the InGaAsP/GaAs heterostructures after a long heating (1–6 hours, 770 °C) has been made too. The analysis of the experimental data led to the conclusion that the fundamental values of the TL in above mentioned systems are about 10 and 1 to 2 nm, correspondingly. This difference between the minimum widths of the TL in AlGaAs/GaAs and InGaAsP/GaAs system is connected with the different speed of solid state diffusional processes which occur at the initial stpeps of liquid – solid contact.     

X-ray diagnostics of P-HEMT AlGaAs/InGaAs/GaAs structures

The structural characteristics of the P-HEMT AlGaAs/InGaAs/GaAs heterostructure have been studied by high-resolution X-ray diffractometry. The parameters of the heterostructure layers were determined by simultaneous analysis of the X-ray reflection curves for the (004) and (113) crystallographic planes. Interface diffusion has been established for the In_yGa_1?yAs quantum well and the Al_xGa_1?x As spacer layer, which are characterized by reconstructed profiles of the lattice parameter distribution and anisotropic distribution of random displacements in the layer plane and in the perpendicular direction.     

CBE growth of GaAs/GaAs, GaAs/Si and AlGaAs/GaAs using TEG, AsH3 and amine-alane precursors

The growth of high quality AlGaAs by CBE has been limited by the high levels of carbon and oxygen contamination. The use of alane based precursors offers a significant reduction in such contamination. We report for the first time the CBE growth of Al_xGa_1−xAs from triethylgallium, dimethylethylamine-alane and arsine, and compare with. growth from triethylgallium, trimethylamine-alane and arsine. Some preliminary results of work on the CBE growth of GaAs on silicon will also be reported.     

Arsenic-free GaAs substrate preparation and direct growth of GaAs/AlGaAs multiple quantum well without buffer layer

High-temperature treatment of GaAs substrate without As flux in a preparation chamber was investigated as a substrate surface cleaning method for molecular beam epitaxial (MBE) growth. Oxide gases such as CO and CO₂ were almost completely desorbed at a temperature above which Ga and As started to evaporate from the substrate. During the cleaning at a temperature as high as 575°C for 30 min, about 100 nm thick GaAs was evaporated from the substrate, but its surface maintained mirror-like smoothness and showed streak pattern with surface reconstruction pattern in the reflection high energy electron diffraction (RHEED) observation. Direct growth of GaAs/Al GaAs quantum well (QW) structures was tried on such surfaces without introducing any buffer layers. The QW structure showed photoluminescence with both intensity and full width at half maximum comparable with those for the QW grown on the substrate cleaned by the conventional method with introducing a GaAs buffer layer.     

Monitoring real-time CBE growth of GaAs and AlGaAs using dynamic optical reflectivity

Dynamic optical reflectivity (DOR) uses the interference oscillations arising from the multiple reflections, of a normally incident CW laser beam, between the surface of a growing film and the film-substrate interface. The oscillations have a period determined by the refractive index of the film and the laser wavelength. DOR measurements have been made, in real time, during the CBE growth of Al_xGa_1−xAs layers on a GaAs(100) substrate. The results show that the growth rate and the aluminum composition x can be monitored.     

Growth and Characterization of Direct-connecting AlGaAs/GaAs TJS Light Emitting Device on SI GaAs Substrate by LPE

High output power (above 3 mW/facet) AlGaAs/GaAs Transverse-Junction Stripe light emitting diodes have been grown on Semi-Insulating (100) GaAs substrates by Liquid Phase Epitaxy. these light emitting diodes utilize a “Direct-connecting” transverse-junction stripe structure, which can confine the transverse-current and reduce the series resistance. By thinning the thickness of the “effective active-layer” of this structure, a room-temperature pulsed lasing operation is also achieved with a threshold current as low as 35 mA and a peak wavelength around 904 nm. This “Direct-connecting” transverse-Junction Stripe light emitting device with a Metal-Semiconductor Field Effect Transistor on an electrical isolated semi-insulating substrate in the future.     

GaAs/AlGaAs quantum wire lasers fabricated by cleaved edge overgrowth

We have used the molecular beam growth technique which we call "cleaved edge overgrowth" to fabricate quantum wire lasers, in which 1D quantum confinement is entirely defined by the growth process. The active region of our lasers consists of atomically precise quantum wires that form at the T-shaped intersections of 7 nm wide GaAs quantum wells grown along the [001] crystal axis and after an in situ cleave along the [110] crystal axis. The origin of the quantum mechanical bound state is the relaxation of quantum well confinement at this intersection. The high degree of structural perfection achievable in this way allows the observation of stimulated optical emission from the lowest exciton state in optically as well as in electrically pumped devices. The formation of a linear p-n junction in which the quantum wires are embedded is achieved by doping with Be and Si in the two orthogonal growth directions. Efficient current injection into the wires is demonstrated by the almost complete suppression of optical emission from the quantum well states as well as by threshold currents as low as 0.4 mA for uncoated devices at 1.7 K.     

Liquid Phase Epitaxy of AlGaInP on GaAs Substrate Using AlGaAs Buffer Layer

Liquid phase epitaxial layers of AlGaInP were successfully grown on Al_0.9Ga_0.1 As buffer layer with varying aluminum melt composition. Epitaxial layers were characterised by using a scanning elelctron microscope, X-ray diffraction, photoluminescence (PL) and Auger depth profile measurements. The shortest peak wavelength of PL spectra obtained in the samples was 630 nm at room temperature. It was found that the thickness of the AlGaInP layer is very small due to rapid change of aluminum in the melt composition.     

Se-doped AlGaAs grown on GaAs(111)A by molecular beam epitaxy

The electrical properties of Se-doped Al_0.3Ga_0.7As layers grown by molecular beam epitaxy (MBE) on GaAs(111)A substrates have been investigated by Hall-effect and deep level transient spectroscopy (DLTS) measurements. In Se-doped GaAs layers, the carrier concentration depends on the misorientation angle of the substrates; it decreases drastically on the exact (111)A surface due to the re-evaporation of Se atoms. By contrast, in Se-doped AlGaAs layers, the decrease is not observed even on exact oriented (111)A. This is caused by the suppression of the re-evaporation of Se atoms, by Se---Al bonds formed during the Se-doped AlGaAs growth. An AlGaAs/GaAs high electron mobility transistor (HEMT) structure has been grown. The Hall mobility of the sample on a (111)A 5° off substrate is 5.9×10⁴ cm²/V·s at 77 K. This result shows that using Se as the n-type dopant is effective in fabricating devices on GaAs(111)A.     

Structural and optical characterization of MOVPE grown InGaP/GaAs MQWs for advanced photovoltaic devices

The optimization of the electronic properties of InGaP/GaAs MQWs, to be inserted in multilayers heterostructure for novel photovoltaic devices, was performed by structural, optical and photoelectrical measurements. Different sequences of nominally undoped InGaP and GaAs alternated layers were grown by low-pressure metalorganic vapour phase epitaxy, employing tertiarybutylarsine and tertiarybutylphosphine as metalorganic precursors for the V-group elements. In order to minimize the As/P exchange effect, the interface In segregation, and to control the whole lattice matching, single and multi-quantum wells (MQWs) with different: (i) periods, (ii) well widths, (iii) growth temperatures, (iv) gas-switching sequences at the interfaces and (v) indium concentrations in the InGaP alloy, were prepared and investigated. The interface sharpness and the compositional fluctuation of thick MQW region containing up to 40 well-barrier sequences were investigated for the modelling, realization and evaluation of test structures based on low-dimensional systems for third generation solar cells.     

New aluminium precursors for MOMBE (CBE): a comparative study

Recently different new Al precursors have been developed to improve the electrical and optical quality of AlGaAs layers grown by MOMBE (CBE), since AlGaAs layers still suffer from the high incorporation of oxygen and carbon. Three approaches are introduced and results obtained from Al_xGa_1−xAs layers (0 < x ≤ 1) are discussed. APAH, a double ring structure molecule, was found to yield AlGaAs layers with high contents of carbon and nitrogen. The use of an Alane-adduct decreases impurity concentrations and improves optical properties. However, TIBAl is superior and provides highest PL response together with carrier concentrations below p = 10¹⁶ cm^-3. Even though the concept of coordinative saturation is promising, results achieved by TIBAl showed that trialkyls could also be well suited for AlGaAs, assuming that they are properly synthesized.