Cellulose II nanoelements prepared from fully mercerized, partially mercerized and regenerated celluloses by 4-acetamido-TEMPO/NaClO/NaClO2 oxidation

A softwood bleached kraft pulp (SBKP) and cotton lint cellulose were fully or partially mercerized, and these along with celluloses and commercially available regenerated cellulose fiber and beads were oxidized by 4-acetamido-TEMPO/NaClO/NaClO₂ at 60 °C and pH 4.8. Weight recovery ratios and carboxylate contents of the oxidized celluloses were 65–80% and 1.8–2.2 mmol g⁻¹, respectively. Transparent and viscous dispersions were obtained by mechanical disintegration of the TEMPO-oxidized celluloses in water. These aqueous dispersions showed birefringence between cross-polarizers, indicating that mostly individualized cellulose nanoelements dispersed in water were obtained by these procedures. Transmission electron microscopy observation showed that the cellulose nanoelements prepared from mercerized SBKP, repeatedly mercerized SBKP, mercerized cotton lint cellulose, regenerated cellulose beads and 18% NaOH-treated SBKP, i.e. partially mercerized SBKP, had similar morphologies and sizes, 4–12 nm in width and 100–200 nm in length. The 18% NaOH-treated SBKP was converted to cellulose nanoelements consisting of both celluloses I and II.     

Wood cellulose nanofibrils prepared by TEMPO electro-mediated oxidation

A softwood bleached kraft pulp (SBKP) was subjected to electro-mediated oxidation in water with TEMPO or 4-acetamido-TEMPO without any chlorine-containing oxidant. Solid recovery ratios of water-insoluble fractions of the oxidized SBKPs were more than 80%, and C6-carboxylate contents increased up to approximately 1 mmol g⁻¹ after oxidation for 48 h. Significant amounts of C6-aldehyde groups (0.17–0.38 mmol g⁻¹) were also formed in the oxidized SBKPs. The degree of polymerization decreased from 2,200 to 520 and 1,400 by the oxidation for 48 h with TEMPO at pH 10 and 4-acetamido-TEMPO at pH 6.8, respectively. The original cellulose I crystal structure and crystallinity of SBKP were maintained after the oxidation, indicating that all C6-oxidized groups were selectively formed on crystalline cellulose microfibril surfaces. The oxidized SBKPs with carboxylate contents of more than 0.9 mmol g⁻¹ were convertible to individual cellulose nanofibrils in yields of more than 80% by disintegration in water.     

Comparison study of TEMPO-analogous compounds on oxidation efficiency of wood cellulose for preparation of cellulose nanofibrils

The effect of chemical structures of TEMPO (2,2,6,6-tetramethylpiperidinyl-1-oxy radical) derivatives and its analogous compounds on oxidation efficiency of C6 primary hydroxyls of wood cellulose was investigated using the NaClO/NaBr system at pH 10. Because the oxidation takes place selectively on the surfaces of cellulose microfibrils, individualized and surface-oxidized cellulose nanofibrils can be obtained by simple mechanical treatment in water, when sufficient amounts of carboxylate groups are formed homogeneously in cellulose microfibrils. 4-acetamide-TEMPO and 4-methoxy-TEMPO showed efficient catalytic behavior with short reaction times (<4 h) and high carboxylate contents (>1.1 mmol/g) in oxidation of wood cellulose, comparable to TEMPO. Correspondingly, these TEMPO derivatives as well as TEMPO gave high nanofibril yields >56%. On the other hand, the use of 4-hydroxy-TEMPO and 4-oxo-TEMPO resulted in the lowest efficiency in oxidation: oxidation times >24 h, carboxylate contents <0.3 mmol/g, and individualized and surface-oxidized nanofibril yields <2%.     

Oxidation of wood cellulose using 2-azaadamantane N-oxyl (AZADO) or 1-methyl-AZADO catalyst in NaBr/NaClO system

A wood cellulose was oxidized with catalytic amounts of 2-azaadamantane N-oxyl (AZADO) or 1-methyl-AZADO, in an NaBr/NaClO system, in water at pH 10. The oxidation efficiency, carboxylate/aldehyde contents, and degree of polymerization (DP_v) of the oxidized celluloses thus obtained were evaluated in terms of the amount of AZADO or 1-methyl-AZADO catalyst added, in comparison with those prepared using the TEMPO/NaBr/NaClO system. When the AZADO/NaBr/NaClO and 1-methyl-AZADO/NaBr/NaClO oxidation systems were applied to wood cellulose using the same molar amount of TEMPO, the oxidation time needed for the preparation of oxidized celluloses with carboxylate contents of 1.2–1.3 mmol/g was reduced from ≈80 to 10–15 min. Moreover, the molar amounts of AZADO and 1-methyl-AZADO that had to be added for the preparation of oxidized celluloses with carboxylate contents of 1.2–1.3 mmol/g were reduced to 1/32 and 1/16 of the amount of TEMPO added, respectively. The DP_v values for the AZADO- and 1-methyl-AZADO-oxidized celluloses after NaBH₄ treatment were in the range of 600–800. This indicated that not only C6-carboxylate groups but also C2/C3 ketones were formed to some extent on the crystalline cellulose microfibril surfaces during the AZADO- and 1-methyl-AZADO-mediated oxidation. When the AZADO-oxidized wood cellulose, which had a carboxylate content of 1.2 mmol/g, was mechanically disintegrated in water, an almost transparent dispersion consisting of individually nano-dispersed oxidized cellulose nanofibrils was obtained, with a nanofibrillation yield of 89 %.     

Surface carboxylation of porous regenerated cellulose beads by 4-acetamide-TEMPO/NaClO/NaClO2 system

A commercial regenerated bead cellulose was suspended in water at pH 4.8, and oxidized with NaClO₂ used as a primary oxidant and catalytic amounts of NaClO and 4-acetamide-2,2,6,6-tetramethylpiperidinyl-1-oxyl radical. Carboxylate groups were formed up to 1.87 mmol/g in the beads by the oxidation of C6 primary hydroxyls to carboxylates without significant weight losses or morphological changes. The spherical shapes, highly porous surface structures consisting of nano-sized fibrils, and the cellulose II crystal structure of the original beads were mostly maintained by the oxidation, indicating that the carboxylate groups formed are predominantly present on the fibril surfaces. Cation-exchange behavior of the TEMPO-oxidized cellulose beads was compared with carboxymethylated cellulose beads, showing that the former was characteristic and superior to the latter in terms of adsorption of metal ions and cationic polymers. Especially, the TEMPO-oxidized cellulose beads had high adsorption behavior of lead ion and high-molecular-weight cationic polymers.     

Cellulose nanofibers from curaua fibers

Curaua nanofibers extracted under different conditions were investigated. The raw fibers were mercerized with NaOH solutions; they were then submitted to acid hydrolysis using three different types of acids (H₂SO₄, a mixture of H₂SO₄/HCl and HCl). The fibers were analyzed by cellulose, lignin and hemicellulose contents; viscometry, X-ray diffraction (XRD) and thermal stability by thermogravimetric analysis (TG). The nanofibers were morphologically characterized by transmission electron microscopy (TEM) and their surface charges in suspensions were estimated by Zeta-potential. Their degree of polymerization (DP) was characterized by viscometry, crystallinity by XRD and thermal stability by TG. Increasing the NaOH solution concentration in the mercerization, there was a decrease of hemicellulose and lignin contents and consequently an increase of cellulose content. XRD patterns presented changes in the crystal structure from cellulose I to cellulose II when the fibers were mercerized with 17.5% NaOH solution. All curaua nanofibers presented a rod-like shape, an average diameter (D) of 6–10 nm and length (L) of 80–170 nm, with an aspect ratio (L/D) of around 13–17. The mercerization of fibers with NaOH solutions influenced the crystallinity index and thermal stability of the resulting nanofibers. The fibers mercerized with NaOH solution 17.5% resulted in more crystalline nanofibers, but thermally less stable and inferior DP. The aggregation state increases with the amount of HCl introduced into the extraction, due to the decrease of surface charges (as verified by Zeta Potential analysis). However, this release presented nanofibers with better thermal stability than those whose acid hydrolysis was carried out using only H₂SO₄.     

Cellulose nanofibres by sonocatalysed-TEMPO-oxidation

The purpose of this work was to study the influence of acoustic cavitation on the oxidation of a mill bleached machine dried hardwood Kraft pulp. The oxidation of the pulp was carried out using 4-acetamido-TEMPO coupled with NaOCl/NaBr as co-oxidizer. The carboxylate content was increased by about 30% without any adverse impact on the degree of polymerization in the case of oxidations under acoustic cavitation compared to the reference without acoustic cavitation. A close correlation between the yield of nanocellulose and the carboxylate content of the oxidized pulps was observed. The individualized cellulose nanofibres were 3–4 nm in width and a few microns in length.     

Structure of cellulose and microcrystalline cellulose from various wood species, cotton and flax studied by X-ray scattering

The structure of microcrystalline cellulose (MCC) made by mild acid hydrolysis from cotton linter, flax fibres and sulphite or kraft cooked wood pulp was studied and compared with the structure of the starting materials. Crystallinities and the length and the width of the cellulose crystallites were determined by wide-angle X-ray scattering and the packing and the cross-sectional shape of the microfibrils were determined by small-angle X-ray scattering. The morphological differences were studied by scanning electron microscopy. A model for the changes in microfibrillar structure between native materials, pulp and MCC samples was proposed. The results indicated that from softwood or hardwood pulp, flax cellulose and cotton linter MCC with very similar nanostructures were obtained with small changes in reaction conditions. The crystallinity of MCC samples was 54–65%. The width and the length of the cellulose crystallites increased when MCC was made. For example, between cotton and cotton MCC the width increased from 7.1 nm to 8.8 nm and the length increased from 17.7 nm to 30.4 nm. However, the longest crystallites were found in native spruce wood (35–36 nm).     

Conversion of cellulose materials into nanostructured ceramics by biomineralization

Synthesis of hierarchically ordered silica materials having ordered wood cellular structures has been demonstrated through in-situ mineralization of wood by means of surfactant-directed mineralization in solutions of different pH. At low pH, silicic acid penetrates the buried interfaces of the wood cellular structure without clogging the pores to subsequently “molecularly paint” the interfaces thereby forming a positive replica following calcinations. At high pH, the hydrolyzed silica rapidly condenses to fill the open cells and pits within the structure resulting in a negative replica of the structure. Surfactant-templated mineralization in acid solutions leads to the formation of micelles that hexagonally pack at the wood interfaces preserving structural integrity while integrating hexagonally ordered nanoporosity into the structure of the cell walls following thermal treatment in air. The carbothermal reduction of mineralized wood with silica at high temperature produces biomorphic silicon carbide (SiC) materials, which are typical aggregations of β-SiC nanoparticles. To understand the roles of each component (lignin, crystalline cellulose, amorphous cellulose) comprising the natural biotemplates in the transformation to SiC rods, three different cellulose precursors including unbleached and bleached pulp, and cellulose nanocrystals have been utilized. Lignin in unbleached pulp blocked homogeneous penetration of silica into the pores between cellulose fibers resulting in non-uniform SiC fibers containing thick silica layers. Bleached pulp produced uniform SiC rods with camelback structures (80 nm in diameter; ∼50 μm in length), indicating that more silica infiltrates into the amorphous constituent of cellulose to form chunky rather than straight rod structures. The cellulose nanocrystal (CNXL) material produced clean and uniform SiC nanowires (70 nm in diameter; >100 μm in length) without the camelback structure.     

Synthesis and characterization of oxidized cellulose

Samples of oxidized cellulose (OC) with various carboxyl contents and degrees of crystallinity were obtained by the oxidation of native and mercerized cellulose with a solution of nitrogen(IV) oxide in CCl₄. A detailed characterization of these OC samples was performed. The effect of oxidation conditions (concentration of N₂O₄ in the solution and oxidation time) and starting cellulose material on OC characteristics (carboxyl, carbonyl and nitrogen content, degree of crystallinity and polymerization, surface area and swelling, and acidic properties) was investigated. Reactivity in the oxidation process was higher in mercerized cellulose than in native cellulose. The action of dilute solutions (10–15%) of N₂O₄ did not affect the degree of crystallinity of cellulose samples. Under these conditions, the oxidation took place mainly in amorphous regions and on the surface of crystallites. Oxidation in a concentrated (40%) N₂O₄ solution led to the destruction of crystallites, which increased the surface area and swelling of cellulose in water. The surface area and the swelling of OC samples increased with a decrease in the index of crystallinity. The acidic properties of OC were shown to increase with an increase of swelling in water. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4785–4791, 2004     

Characterization of cellulose nanofibrils prepared by direct TEMPO-mediated oxidation of hemp bast

Hemp bast (α-cellulose 79.4%, Klason lignin 4.9%) was directly oxidized by 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO)-mediated oxidation in water at pH 10 and room temperature for 2 h. The level of added NaClO in oxidation varied from 5 to 30 mmol/g (based on dry weight of hemp bast). Weight recovery ratios of the TEMPO-oxidized hemp bast celluloses were in the range of 81–91%, and their carboxylate contents increased up to 1.2 mmol/g with the increased NaClO addition level. The lignin contents decreased to 0.5–0.9% after oxidation, and the viscosity-average degrees of polymerization decreased from 1100 to 560 because of depolymerization during oxidation. Thus, direct TEMPO-mediated oxidation of hemp bast introduced a significant number of carboxylate groups and simultaneously achieved sufficient delignification. Small amounts of xylose, mannose, and rhamnose originating from hemicelluloses remained in the TEMPO-oxidized hemp bast samples prepared by oxidation with 5–20 mmol/g NaClO. However, oxidation with 30 mmol/g NaClO completely removed these hemicellulose-originating sugars, and produced almost pure TEMPO-oxidized cellulose. When TEMPO-oxidized hemp bast samples were mechanically disintegrated in water, their nanofibrillation yields were 58–65%. After removal of unfibrillated fractions by centrifugation, transparent dispersions showed birefringence when observed between cross-polarizers, while atomic force microscopy images showed near-individually dispersed nanofibril elements with widths of ~2 nm.     

Immobilization of lysozyme-cellulose amide-linked conjugates on cellulose I and II cotton nanocrystalline preparations

Lysozyme was attached through an amide linkage between some of the protein’s aspartate and glutamate residues to amino-glycine-cellulose, which was prepared by esterification of glycine to preparations of cotton nanocrystals. The nanocrystalline preparations were produced through acid hydrolysis and mechanical breakage of the cotton fibers from a scoured and bleached cotton fabric and a scoured and bleached, mercerized fabric, which was shown to produce cellulose I (NCI) and cellulose II (NCII) crystals respectively. A carbodiimide-activation coupling reaction was used to create the lysozyme-amino-glycine-cellulose conjugates using both NCI and NCII in a polar solvent and gave yields of covalently linked lysozyme at 604 mg/gram of cotton nanocrystal. The incorporation of lysozyme conjugated to the NCI and NCII preparations gave very high activity (1,500 U/mg cotton) when assessed using a fluorescence tag assay to measure antimicrobial activity against Micrococcus lysodeikticus. Scanning electron micrographs demonstrated an aggregation of nanoparticles corresponding to lysozyme bound on the surface of larger cotton nanocrystalline sheets. The approach of producing high enzyme activity on cotton nanocrystals is discussed in the context of selectively presenting robust hydrolase activity on nanocrystalline surfaces.     

Enzymatic degradation of oxidized cellulose hydrogels

The cellulose-based hydrogel with abundant aldehyde groups was prepared by periodate oxidation of cellulose hydrogel prepared by dissolution-regeneration of cellulose by aqueous LiOH/urea solvent. Aldehyde groups could be introduced retaining the nanoporosity of the cellulose gel. The enzymatic degradation of three grades of oxidized cellulose hydrogel, with aldehyde contents of 3.3, 8.1 and 18.6 per 100 glucose unit, was carried out using solutions containing cellulase and β-glucosidase at 37 °C up to 48 h. The degradation of oxidized gels was remarkably slower than that of original cellulose gel, depending strongly on the degree of oxidation. The portion except for the amount of glucose released was greater than the degree of oxidation, but became closer to the latter with increase in the degree of oxidation. This behavior can be interpreted in terms of the enzymatic recognition of the chemically modified cellulose chains.     

Enzymatic hydrolysis of cellulose I is greatly accelerated via its conversion to the cellulose II hydrate form

Cellulose II hydrate was prepared from microcrystalline cellulose (cellulose I) via its mercerization with 5 N NaOH solution over 1 h at room temperature followed by washing with water. The structure of cellulose II hydrate changed to that of cellulose II after drying. Compared with cellulose II, cellulose II hydrate exhibited a slightly (8.5%) expanded structure only along the direction. The hydrophobic stacking sheets of the cellulose II were conserved in the cellulose II hydrate, and water molecules could be incorporated in the inflated two-chain unit cell of cellulose II hydrate. Enzymatic hydrolysis of cellulose I, cellulose II hydrate, and cellulose II was carried out at 37 °C using solutions comprising a mixture of cellulase and β-glucosidase. The hydrolysis of cellulose II hydrate proceeded much faster than the hydrolysis of the other two substrates, while the saccharification ratio of cellulose II was only slightly higher than that of cellulose I. The alkaline mercerization treatment was also applied to sugarcane bagasse. After its direct mercerization, the cellulose in bagasse was converted from cellulose I to cellulose II hydrate, and then to cellulose II after drying. Similar to in the case of microcrystalline cellulose, the rate of the enzymatic hydrolysis of the mercerized bagasse without drying (cellulose II hydrate) was much faster than the enzymatic hydrolysis of the other two substrates. Thus, the wet forms of cellulose and cellulosic biomass after mercerization, and after hydrolysis with cellulolytic enzymes, afforded superior products with extremely high degradability.     

Stoichiometry and stability of cellulose-hydrazine complexes

Highly crystalline cellulose samples from green algae (cellulose I) and mercerized ramie (cellulose II) were treated with anhydrous hydrazine and the resulting complexes were analyzed by synchrotron X-ray diffraction and thermogravimetry. Cellulose I-hydrazine complex could be fully described by a two-chain monoclinic unit cell, a = 0.879 nm, b = 1.076 nm, c = 1.038 nm, and γ = 122.0°, with space group P2₁. Cellulose II-hydrazine complex prepared from mercerized ramie gave a different two-chain monoclinic unit cell, a = 1.042 nm, b = 1.046 nm, c = 1.038 nm, γ = 129.7°, also with space group P2₁. Though having different crystal structures, the number of hydrazine molecules per glucopyranoside residue was 0.82 for cellulose I-complex and 0.93 for cellulose II-complex, probable stoichiometric value of 1.0. Hydrazine could be extracted from the complexes by organic solvents retaining the crystalline orders, resulting in the allomorphic conversion to cellulose III_I and cellulose III_II, both having non-staggered chain arrangements. These features are similar to those of cellulose-ethylenediamine complexes.     

Cellulose gel and aerogel from LiCl/DMSO solution

Recently-discovered lignocellulosic solvent, 8%(w/w) lithium chloride/dimethyl sulfoxide (LiCl/DMSO), was found to dissolve cellulose of varied crystal forms and degree of polymerization. Cellulose samples could be activated for dissolution by complexation with ethylenediamine (EDA), giving EDA contents of 20–23% (w/w) in the complex irrespective of the cellulose type. The cellulose solution gave well-resolved ¹³C NMR spectrum, confirming molecular dispersion. Cellulose could be coagulated by ethanol to give translucent cellulose gels, which could be converted to highly porous aerogels via solvent exchange drying. Nitrogen adsorption analysis gave their specific surface areas of 190–213 m²/g, with typical mesopore sizes of 10–60 nm. Scanning electron microscopy revealed the network structure of aerogel composed of relatively straight fibril segments, approx. 20 nm wide and 100–1,000 nm long. X-ray diffraction showed that the material is poorly crystalline cellulose II.     

Surface forces measurements of spin-coated cellulose thin films with different crystallinity

A systematic study of the surface forces between a cellulose sphere and cellulose thin films of varying crystallinity has been conducted as a function of ionic strength and pH. Semicrystalline cellulose II surfaces and amorphous cellulose films were prepared by spin-coating of the precursor cellulose solutions onto oxidized silicon wafers before regeneration in water. Crystalline cellulose I surfaces were prepared by spin-coating wafers with aqueous suspensions of sulfate-stabilized cellulose I nanocrystals. These preparation methods produced thin, smooth films suitable for surface forces measurements. The interaction with the cellulose I was monotonically repulsive at pH 3.5, 5.8, and 8.5 and at 0.1, 1, and 10 mM ionic strengths. This was attributed to the presence of strongly ionizable sulfur-containing groups on the cellulose nanocrystal surfaces. The amorphous film typically showed a steric interaction up to 100 nm away from the interface that was independent of the solution conditions. A range of surface forces were successfully measured on the semicrystalline cellulose II films; attractive and repulsive regimes were observed, depending on pH and ionic strength, and were interpreted in terms of van der Waals and electrostatic interactions. Clearly, the forces acting near cellulose surfaces are very dependent on the way the cellulose surface has been prepared.     

Molecularly thin nanoparticles from cellulose: isolation of sub-microfibrillar structures

We have succeeded in isolating nanostructures from never-dried cellulose wood pulp, in sheet-form that have sub-microfibril dimensions (single to double digit Å thickness with 100’s of nm in length). A recently developed oxidation procedure by Saito and co-workers (Biomacromolecules 2006, 7:1687–1691) combined with extensive ultrasonication was used to liberate nanoscale cellulose fibrils. We show structures, as determined with atomic force microscopy, that compose the well-known cellulose microfibril, which are tenfold thinner than previous reports on nanoscale celluloses. This work provides indirect evidence in support of, and is consistent with, the hypothesis that the intersheet van der Waals bonding of the cellulose fibril is significantly weaker than the intrasheet hydrogen bonding of the cellulose microfibril. The structures are facile to isolate, contain enormous specific surface area with rich chemical functionality providing potential for numerous novel applications.     

Preparation of tough cellulose II nanofibers with high thermal stability from wood

Well-dispersed cellulose II nanofibers with high purity of 92 % and uniform width of 15–40 nm were isolated from wood and compared to cellulose I nanofibers. First, ground wood powder was purified by series of chemical treatments. The resulting purified pulp was treated with 17.5 wt% sodium hydroxide (NaOH) solution to mercerize the cellulose. The mercerized pulp was further mechanically nanofibrillated to isolate the nanofibers. X-ray diffraction patterns revealed that the purified pulp had been transformed into the cellulose II crystal structure after treatment with 17.5 wt% NaOH, and the cellulose II polymorph was retained after nanofibrillation. The cellulose II nanofiber sheet exhibited a decrease in Young’s modulus (8.6 GPa) and an increase in fracture strain (13.6 %) compared to the values for a cellulose I nanofiber sheet (11.8 GPa and 7.5 %, respectively), which translated into improved toughness. The cellulose II nanofiber sheet also showed a very low thermal expansion coefficient of 15.9 ppm/K in the range of 20–150 °C. Thermogravimetric analysis indicated that the cellulose II nanofiber sheet had better thermal stability than the cellulose I nanofiber sheet, which was likely due to the stronger hydrogen bonds in cellulose II crystal structure, as well as the higher purity of the cellulose II nanofibers.     

Thermal stabilization of TEMPO-oxidized cellulose

A partially C6-carboxylated cellulose with carboxylate content of 1.68 mmol/g was prepared by 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO)-mediated oxidation of a softwood bleached kraft pulp. Thermogravimetric analyses of the TEMPO-oxidized cellulose (TOC) and its related materials were studied to improve thermal stability of the TOC. Thermal decomposition (T_d) points of the TOC with sodium carboxylate groups, alkali-treated TOC with free carboxyl groups of 0.23 mmol/g and the original cellulose were 222 °C, 264 °C and 275 °C, respectively. Thus, the anhydroglucuronic acid units formed by TEMPO-mediated oxidation of the native wood cellulose and present in the TOC cause the decrease in T_d point by decarbonation during heating process. When carboxyl groups in the TOC were methylated with trimethylsilyl diazomethane (TMSCHN₂), the T_d point increased from 222 °C to 249 °C, and the peak temperature in its derivative thermogravimetric (DTG) curve increased from 273 °C to 313 °C, which was almost equal to that of the original cellulose. Thus, the methyl esterification of carboxyl groups in the TOC is effective in improving thermal stability. When sodium ions present in the TOC as counter ions of carboxylate groups were exchanged to some other metal ions, thermal stability was improved to some extent. Especially, when CaCl₂, Ca(OAc)₂, Ca(NO₃)₂ and CaI₂ solutions were used in the ion-exchange treatments, the peak temperatures in the DTG curves increased to approximately 300 °C. MgCl₂, NiCl₂, SrCl₂ and Sr(OAc)₂ solutions were also effective to some extent in increasing the peak temperatures of DTG curves. Thus, thermal stability of the fibrous TOC can be improved to some extent by methyl esterification of the sodium carboxylate groups present in the original TOC with TMSCHN₂ or ion-exchange treatments with some metal salt solutions.