Reduction of Nitrobenzene to Aniline with Carbon Monoxide and Water in the Presence of the PdCl2/Fe/I2 System

A study of modified catalyst systems composed of palladium or its chloride and a co-catalyst such as metallic Fe-powder, iodine, and pyridine was used in the reduction of nitrobenzene to aniline with carbon monoxide and water at 180°C and 2.5-4 MPa pressure. The reaction is complete in 2 h with a nitrobenzene conversion of 98-100% and a 100% selectivity with respect to aniline.     

Effect of substitution of Fe3+ in CuCr2O4 matrix for the hydrogenation of nitrobenzene

The hydrogenation of nitrobenzene to aniline over reduced Cu(Fe_xCr_2–x)O₄ series of catalysts (where x=0, 0.2, 0.4, 0.6, 0.8 and 1.0) has been studied at 250°C in a fixed bed flow type reactor. All the catalysts were characterized by XRD, IR and DRS analysis and by measurements of electrical conductivity and surface area. The conversion of nitrobenzene to aniline is maximum over the catalysts with composition x=0.4. By comparing the results of reversible and irreversible adsorption of carbon monoxide with hydrogenation activity, it can be concluded that univalent copper at octahedral sites is more active for hydrogenation than metallic copper. The second cations [Cr(III) or Fe(III)] develop their catalytic activity by sharing anionic vacancies.     

Photoreduction of nitrobenzene to aniline in “hybrid” photocatalytic systems

Irradiation of suspensions of CdS in water-ethanol mixtures containing nibrobenzene with light at > 320 run does not in practical terms lead to the reduction of the nitrobenzene to aniline. It has been shown that the formation of aniline occurs when solvato complexes of vanadium(III) (PhNH₂=18.1·10^–3) and vanadium(IV) (PhNH₂= 2.84·10^–3) are added to the system. The photocatalytic reduction of nitrobenzene is accompanied by oxidation of the alcohol to acetaldehyde and acetal. The proposed process mechanism includes stages and acceptance of an electron photogenerated in the semiconductor by vanadium compounds and of a hole by molecules of the alcohol and subsequent stages of reaction of the reduced forms of vanadium, and also of the ethoxy radicals with nitrobenzene, which leads to its reduction.Translated from Teoreticheskaya i Éksperimental'naya Khimiya, Vol. 25, No. 5, pp. 550–557, September–October, 1989.     

The influence of aniline and its derivatives on the corrosion behaviour of copper in acid solution

The inhibiting action of aniline and its derivatives on the corrosion of copper in hydrochloric acid has been investigated, with emphasis on the role of substituents. With this purpose five different anilines were selected: aniline, p-chloro aniline, p-nitro aniline, p-methoxy and p-methyl aniline. The electrochemical and gravimetric results, obtained in the absence and presence of different concentrations of inhibitors, revealed that aniline reduces the corrosion of copper, with a critical concentration of 10^–2 M. Furthermore, the interaction energy calculated as G_ads gave a value of 4.2 kcal mol^–1 indicating physisorption of the organic compound at the copper surface. The results have also shown that substituents, either electron donors (–CH₃, –OCH₃) or, electron acceptors (–NO₂, –Cl) in para position, decrease the inhibition action of aniline. A theoretical study using molecular mechanic and ab initio Hartree Fock methods, to model the adsorption of aniline on copper (100) showed results in good agreement with the experimental data. Aniline adsorbs parallel to the copper surface, showing no preference for a specific adsorption site. On the other hand, from ab initio Hartree Fock calculations, an adsorption energy between 2 kcal/mol and 5 kcal/mol is obtained, which is close to the experimental value, confirming that the adsorption of aniline on the metal substrate is rather weak. In view of these results, the orientation of the aniline molecule with respect to the copper surface is considered to be the dominant effect.     

Insights on the Electrocatalytic Seawater Splitting at Heterogeneous Nickel-Cobalt Based Electrocatalysts Engineered from Oxidative Aniline Polymerization and Calcination

Given the limited access to freshwater compared to seawater, a growing interest surrounds the direct seawater electrolysis to produce hydrogen. However, we currently lack efficient electrocatalysts to selectively perform the oxygen evolution reaction (OER) over the oxidation of the chloride ions that are the main components of seawater. In this contribution, we report an engineering strategy to synthesize heterogeneous electrocatalysts by the simultaneous formation of separate chalcogenides of nickel (NiS_x, x = 0, 2/3, 8/9, and 4/3) and cobalt (CoS_x, x = 0 and 8/9) onto a carbon-nitrogen-sulfur nanostructured network. Specifically, the oxidative aniline polymerization in the presence of metallic cations was combined with the calcination to regulate the separate formation of various self-supported phases in order to target the multifunctional applicability as both hydrogen evolution reaction (HER) and OER in a simulated alkaline seawater. The OER’s metric current densities of 10 and 100 mA cm⁻² were achieved at the bimetallic for only 1.60 and 1.63 V_RHE, respectively. This high-performance was maintained in the electrolysis with a starting voltage of 1.6 V and satisfactory stability at 100 mA over 17 h. Our findings validate a high selectivity for OER of ~100%, which outperforms the previously reported data of 87–95%.     

Hydrogen transfer hydrogenation of nitrobenzene to aniline with Ru(acac)3 as the catalyst

Tris(acetylacetonato)ruthenium(III)(Ru(acac)₃) was synthesized with RuCl₃·nH₂O and acetylacetone as raw materials. The structure of Ru(acac)₃ was identified by FI-IR, ¹H NMR, ¹³C NMR, and elemental analysis. It was used in the catalytic hydrogen transfer hydrogenation of nitrobenzene with sodium formate as hydrogen donor. The effects of reaction conditions on the process, such as temperature, time, dosage of catalyst, and kinds of hydrogen donor, were investigated. The optimal reaction parameters were determined as follows: 80 °C, 4.0 h, the substrate nitrobenzene 20 mL, sodium formate 27.20 g, Ru(acac)₃ 0.96 g, the conversion of nitrobenzene is 100.0 %, the yield of aniline and the selectivity to aniline are 96.65 %. The reaction mechanism is proposed and analyzed. It exhibited excellent catalytic properties in the hydrogen transfer hydrogenation of nitrobenzene to aniline.     

Homogeneous photocatalysis of ethanol reduction of nitrobenzene by titanium complexes

It was shown that when ethanol solutions of nitrobenzene are irradiated with near-UV light, which is absorbed by labile complexes of titanium(IV) present in the system, aniline is accumulated. The quantum yield of C₆H₅NH₂ formation if weakly dependent on the C₆H₅N0₂ concentration and increases with increasing titanium(lV) content in solution.Translated from Teoreticheskaya i Éksperimental'naya Khimiya, Vol. 28, Nos. 5–6, pp. 416–419, September–December, 1992.     

Effect of organic additives on activity of PdCl2, in synthesis of phenyl isocyanate by carbonylation of nitrobenzene

Conclusions The activity of PdCl₂ as a catalyst for the carbonylation of nitrobenzene to phenyl isocyanate at 190° and an initial CO pressure of 100 atm increases by 6–9 times when either pyridine or quinoline is added to the reaction system.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 11, pp. 2597–2598, November, 1977.     

Synthesis of imines from nitrobenzene and TiO2 particles suspended in alcohols via semiconductor photocatalysis type B

UV irradiation on a non-aqueous suspension of titanium dioxide with nitrobenzene and different alcohols in deaerated conditions produces imines and aniline as main products. The conversion of nitrobenzene and the corresponding selectivity of imines or aniline depend on the type of alcohol used. A low conversion (3-12%) and selectivity close to 100% to imines were obtained with methyl, ethyl, or propyl alcohol. Otherwise, using i-propanol only aniline was detected with a conversion of 13%. Finally, a mixture of aniline and imines was formed employing n-butyl, n-amyl, and i-amyl alcohols with the higher conversion (∼50%).     

白藜芦醇作辣根过氧化物酶底物的布氏杆菌抗体酶联免疫传感器研究

一种纯天然产物白藜芦醇用作辣根过氧化物酶(HRP)底物。对其化学性质的研究证实,白藜芦醇在空气中较稳定,对HRP、H2O2的电化学响应性能优于传统HRP底物,对人体无毒害。白藜芦醇在HRP催化下可被H2O2氧化成醌,产物醌在电极上于-376 mV处可被还原,其电流的大小与HRP的浓试在一定浓度范围内呈线性相关。将兔布氏杆菌抗原包埋在石墨-石蜡基质中制备了测定兔布氏杆菌抗体的电化学酶联免疫传感器,该传感器测定兔布氏杆菌抗体的线性范围为3×10-4~1.65×10-2g/L;检出限为1×10-4g/L;RSD为4.6%。本方法制备免疫传感器的电化学性能稳定,抗原活性保持良好。     

Reduction of nitrobenzene to aniline with carbon monoxide and water

Modified catalytic system composed of selenium and cocatalysts such as pyridine and aniline, applied in the reduction of nitrobenzene to aniline in the presence of carbon monoxide and water is described. The reaction proceeds at 150–200°C and 3–4 MPa gauge pressure. After 1–2 h the reaction is complete, reaching nitrobenzene conversions of up to 98% with selectivity to aniline near 100%.     

Effect of organic additives on activity of selenium catalyst in synthesis of phenylurethane by carbonylation of nitrobenzene

Conclusions Amines of variable basicity either promote or inhibit the formation of phenylurethane from nitrobenzene and CO in ethanol medium. Morpholine and aniline are the most efficient promoters of the reaction.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 7, pp. 1654–1655, July, 1981.     

Quantitative chemical analysis on paper: Determination of phosphate in the presence of large quantities of other ions

Summary A rapid method has been developed for the determination of phosphate by means of filter paper impregnated with lead iodide. A sample is added to the impregnated filter paper by means of a capillary, and after irrigation to cause migration of the ions a white spot is obtained as the lead iodide is converted into the phosphate. The weight of the spot is dependent on the p_H and the quantity of phosphate present.The determination is possible in the presence of SCN^–, Cl^–, Br^–, NO₃ ^–, CO₃ ^–, I^–, IO₃ ^–, CH₃COO^–, B₄O₇ ^2–, F^–, Sb₂O₇ ^4–, K⁺, Na⁺, NH₄ ⁺, OH^–, H⁺, succinic, citric and tartaric acids. The determination is impossible in the presence of C₂O₄ ^2–, SO₄ ^2–, MoO₄ ^2–, NO₂ ^–, SO₃ ^2–, S^2–, CrO₄ ^2–, or CO₃ ^2–.The method permits the determination of 7–100g of phosphate with an accuracy of 2%.

---

Zusammenfassung Ein schnelles Verfahren zur Phosphatbestimmung wird besehrieben, bei dem man sich eines mit Bleijodid imprägnierten Filterpapiers bedient. Die Probe wird mit einer Kapillare auf das Papier aufgebracht. Man erleichtert die Ionenbewegung durch geeignete Befeuchtung und erhält einen weißen Fleck infolge Umsetzung des Bleijodids in -phosphat. Das Gewicht des Fleckens hängt vom p_H und von der Phosphatmenge ab.Die Bestimmung ist möglich in Gegenwart von SCN^–, Cl^–, Br^–, NO₃ ^–, CO₃ ^–, J^–, JO₃ ^–, CH₃COO^–, B₄O₇ ^2–, F^–, Sb₂O₇ ^4–, K⁺, Na⁺, NH₄ ⁺, OH^–, H⁺, Bernsteinsäure, Zitronensäure und Weinsäure; sie ist nicht möglich bei Gegenwart von C₂O₄ ^2–, SO₄ ^2–, MoO₄ ^2–, NO₂ ^–, SO₃ ^2–, S^2–, CrO₄ ^2– oder CO₃ ^2–. 7 bis 100g Phosphat können mit einer Genauigkeit von 2% bestimmt werden.

---

Résumé On a développé une méthode rapide pour le dosage des phosphates sur papier-filtre imprégné d'iodure de plomb. On dépose l'échantillon sur le papier-filtre imprégné, à l'aide d'un capillaire, et, après humidification pour provoquer la migration des ions, on obtient une tache blanche quand l'iodure de plomb est converti en phosphate. Le poids de la tache dépend du p_H et de la quantité de phosphate présent.Le dosage est possible en présence de SCN^–, Cl^–, Br^–, NO₃ ^–, CO₃ ^–, I^–, IO₃ ^–, CH₃COO^–, B₄O₇ ^2–, F^–, Sb₂O₇ ^4–, K⁺, Na⁺, NH₄ ⁺, OH^–, H⁺, et des acides succinique, citrique et tartrique. Il est impossible en présence de C₂O₄ ^2–, SO₄ ^2–, MoO₄ ^2–, NO₂ ^–, SO₃ ^2–, S^2–, CrO₄ ^2– ou CO₃ ^2–.La méthode permet le dosage de 7 à 100g de phosphate avec une précision de 2%.

     

Palladium(II)-catalyzed Amination of Isoprene with Aniline

The reaction of isoprene with aniline, catalyzed by the Pd(acac)₂-(RO)₃P-CF₃CO₂H system, 1 : 4 : 4 [R = Me, Et; acac = (CH₃CO)₂CH], in MeCN provides N-(3-methylbut-2-en-1-yl)aniline with a high selectivity (up to 84%) and a nearly quantitative yield (75%). At 1 : 4 : 20 and 1 : 4 : 40 molar component ratios in the catalytic system, up to 28–31% of N,N-(2,3-dimethylprop-2-en-1-yl)aniline is formed. Telomeric reaction products appear at 1 : 2 : 4 and 1 : 1 : 10 ratios.__________Translated from Zhurnal Obshchei Khimii, Vol. 75, No. 6, 2005, pp. 963–968.Original Russian Text Copyright © 2005 by Petrushkina, Mysova, Orlinkov.     

Reductive alkylation of p-phenylenediamine and its hydroquinone complex with ketones in presence of rhenium and palladium sulfides

Conclusions Conditions were found (150–200°, hydrogen pressure 110–150 atm, reaction time 3 h) for the reductive alkylation of p-phenylenediamine and its hydroquinone complex with acetone, butanone, and cyclohexanone in presence of Re₂S₇ or PdS as catalyst, and N,N'-diisopropyl-, N,N'-di-s-butyl-, and N,N'-dicyclohexyl-p-phenylenediamines and their hydroquinone complexes were obtained in 60–90% yield.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 7, pp. 1601–1605, July, 1968.     

Synthesis and properties of phenyl(methyl)-substituted 2- and 4-nitrosopyrimidines

Phenyl(methyl)-substituted 2- and 4-nitroso- and azoxypyrimidines were synthesized for the first time by the oxidation of phenyl(methyl)-substituted 2- and 4-hydroxy-aminopyrimidines by activated MnO₂, Ag₂CO₃ on zeolite, or BaMnO₄. Certain chemical properties of the synthesized nitrosopyrimidines were studied, such as reduction, nucleophilic substitution of the nitroso group, the condensation reaction with aniline and hydroxyaminopyrimidines.For Preliminary communication, see [1].DeceasedTranslated from Khimiya Geterotsiklicheskikh Soedinenii, No. 7, pp. 962–968, July, 1989.     

Catalytic carbonylation for the synthesis of chemical intermediates

Chemistry related to three catalytic carbonylation reactions is discussed. Synthesis of diphenylurea from nitrobenzene, aniline, and CO gives isolated yields above 98% at 100–120 °C and 15–60 bar of CO in the presence of a palladium (II) complex, PPh₃ and NEt₄Cl. Experimental evidence was provided to prove a new reaction stoichiometry and involvement of a carbamoyl intermediate. In carbonylation of HCHO over ion exchange resin catalysts, reaction temperature, time, pressure, and solvent were important variables to obtain high yields of methyl glycolate. Carbonylation of isobutylphenylethanol at 120°C and 40 bar of CO in the presence of PdCl₂−PPh₃−HCl gives 98% yield of α-(4-isobutylphenyl) propionic acid (ibuprofen). Each catalyst component had a definite role that is indispensable for an efficient overall reaction.     

组合型Pt3Sn/Al2O3催化剂用于芳香硝基化合物一锅法合成N-烷基芳胺

采用吸附法制备了组合型Pt₃Sn/Al₂O₃双金属催化剂, 将该催化剂用于芳香硝基化合物原位液相加氢一锅法合成N-烷基芳胺. 研究表明, 在503 K, 空速为7.5 h^-1, 水体积分数为5%时, 1%(质量分数)Pt₃Sn/Al₂O₃催化剂具有较高的催化性能, 硝基苯的转化率为100%, N-乙基苯胺和N,N-二乙基苯胺的总选择性为98.2%. 同时,该催化剂对原位液相加氢烷基化反应具有一定普适性, 本文研究的14 种芳香硝基化合物与低级脂肪醇反应,均具有较高的N-烷基化产率.     

Polymer heterogenized iridium amino complexes. Catalyzed reduction of nitrobenzene under WGSR conditions

The activation studies for catalytic reduction of nitrobenzene to aniline by iridium(I) complexes, [Ir(COD)(amine)₂]PF₆ (COD=1,5-cyclooctadiene, amine =4-picoline, 3-picoline, 2-picoline, or pyridine) heterogenized on poly(4-vinylpyridine) in aqueous 2-ethoxyethanol are described. The aniline formation (mmol, based on CO₂ formed after 9 h) followed the order: 4-picoline (0.068)>2-picoline (0.052)>3-picoline (0.046)≥pyridine (0.042) for 1.0×10⁻⁴ mol Ir/0.5 g of polymer, 0.26 mL of nitrobenzene, 10 mL of 2-ethoxyethanol/water, 8/2, v/v, P(CO)=0.9 atm, at 100°C.     

2D and 1D Coordination Polymers with the Ability for Inclusion of Guest Molecules: Nitrobenzene, Benzene, Alkoxysilanes

The complexation reactions of the electron rich, linear and bi-functional ligand, 9,10-bis(4-pyridyl)anthracene, with metal salts Cd(NO₃)₂, CdI₂, CoI₂ and CuI in the presence of guest molecules nitrobenzene, benzene and alkoxysilanes were studied. The single crystal analyses of the complexes reveal that an electron deficient guest molecule such as nitrobenzene consistently templated the open two-dimensional network with grid dimensions of ca. 15 × 15Å. On the other hand the presence of benzene or alkoxysilane templated1D-zigzag chains and/or 2D-grid layers. The crystal structures revealthe importance of host–guest interactions in tailoring the network architectures ofcoordination polymers.