Solvothermal synthesis of WO3/TiO2/carbon fiber composite photocatalysts for enhanced performance under sunlight illumination

Carbon fiber (CF)‐based WO₃/TiO₂ composite catalysts (WO₃/TiO₂/CF) were successfully synthesized by solvothermal method. The catalysts were characterized by XPS, SEM, BET, XRD, FTIR, Raman and UV–Vis. The analyses confirmed the WO₃/TiO₂ nanoparticles with high crystallinity deposited on the carbon structure. The photocatalytic degradation of Orange II azo dye under UV and sunlight illumination with the synthesized catalyst was explored. The composite catalyst displayed high performance (85%) for Orange II degradation while that of for WO₃/TiO₂ was found as 76%. The effects of CF amount, solution pH, initial dye concentration and catalyst dose on photocatalytic performance were studied. It was found that the degradation efficiency increased from 68% to 90% with the increasing CF amount from 3 wt% to 5 wt%, while the further increase in CF amount (7–10 wt%) decreased the photodegradation due to the blocking the active sites of WO₃/TiO₂. The enhanced photocatalytic efficiency was mainly attributed to the electrical properties of the CF and reduced bandgap.     

Microwave-assisted synthesis of the Fe2O3/g-C3N4 nanocomposites with enhanced photocatalytic activity for degradation of methylene blue

The preparation and photocatalytic performance of the Fe₂O₃/g-C₃N₄ nanocomposites with different weight percentage of iron was investigated in this study. Samples were successfully synthesized using melamine and ferric nitrate as the precursors via the green and facile microwave-assisted method. The physicochemical and structural properties of the Fe₂O₃-doped g-C₃N₄ were characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR), the Brunauer–Emmett–Teller (BET) method, transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and ultraviolet–visible spectroscopy (UV–Vis). The photocatalytic activity of the Fe₂O₃/g-C₃N₄ catalysts was evaluated by the degradation of methylene blue (MB) at room temperature under visible light irradiation. As expected, the as-synthesized samples exhibited considerable improvement in the photodegradation of MB. The Fe₂O₃/g-C₃N₄ (1.0 wt%) nanocomposite had superior photocatalytic activity, with almost 70% degradation efficiency within 90 min of irradiation. The enhanced performance was ascribed to the separation and migration of the photoinduced electron–hole pairs and taking part of the charge carriers in the chemical redox reactions at the surface of the photocatalyst. In this work, the effect of Fe weight percentage on the degradation potential was also studied, and the photocatalytic mechanism was proposed with the main reactive species •OH.     

Synthesis of Three‐dimensionally Ordered Macroporous TiO2 and TiO2/WO3 Composites and Their Photocatalytic Performance

This work presents the characterization and preparation of three‐dimensionally ordered macroporous TiO₂ and TiO₂/WO₃ composite nanoparticles with enhanced visible‐light‐responsive properties for rhodamine B (Rh B) photodegradation. The 3DOM TiO₂ and TiO₂/WO₃ composites were prepared through a dip‐infiltrating sol‐gel process using a polystyrene (PS) colloidal crystal template. The materials were characterized by SEM, TEM, XRD, BET, XPS and UV/Vis. The 3DOM TiO₂/WO₃ composite structures ranged from well‐defined 3DOM structures, which are highly ordered and interconnected via small pore windows, to collapsed three‐dimensional structures as the WO₃ content increased. The photoresponse range and specific surface area of the composite increased with less than 0.025 g of WCl₆. The 3DOM TiO₂/WO₃ composite with less than 0.025 g of WCl₆ exhibited a higher catalytic activity than 3DOM TiO₂ for the photocatalytic degradation of Rh B under simulated sunlight illumination.     

Pd nanoparticle-modified Bi2WO6 nanoplates used for visible-light-driven photocatalyst

Pd nanoparticles supported on Bi₂WO₆ nanoplates used for visible-light-driven photocatalyst were successfully synthesized by photoreduction deposition method under visible-light irradiation. Different analytical techniques including X-ray diffraction, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, scanning electron microscopy, transmission electron microscopy and photoluminescence spectroscopy revealed that face-centered cubic metallic Pd nanoparticles were uniformly loaded on top of orthorhombic Bi₂WO₆ nanoplates to form heterostructure Pd/Bi₂WO₆ nanocomposites. Photocatalytic activities of pure Bi₂WO₆ sample and heterostructure Pd/Bi₂WO₆ nanocomposites were studied through the photodegradation of rhodamine B (RhB) under visible-light irradiation. The photocatalytic efficiency of Bi₂WO₆ was increased to the highest by being loaded with 5 wt% Pd and then decreased by being loaded with 10 wt% Pd. The improved photocatalytic efficiency caused by high-efficiency diffusion and separation of photo-generated charge carriers was explained and can lead to superior photodegradation of RhB under visible-light irradiation.

     

Hydrothermal preparation and visible-light photocatalytic activity of Bi2WO6 powders

Bi₂WO₆ powder photocatalyst was prepared using Bi(NO₃)₃ and Na₂WO₄ as raw materials by a simple hydrothermal method at 150 °C for 24 h, and then calcined at 300, 400, 500, 600 and 700 °C for 2 h, respectively. The as-prepared samples were characterized with UV-visible diffuse reflectance spectra, fourier transform infrared spectra (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and N₂ adsorption-desorption measurement. The photocatalytic activity of the samples was evaluated using the photocatalytic oxidation of formaldehyde at room temperature under visible light irradiation. It was found that post-treatment temperature obviously influenced the visible-light photocatalytic activity and physical properties of Bi₂WO₆ powders. At 500 °C, Bi₂WO₆ powder photocatalyst showed the highest visible-light photocatalytic activity due to the samples with good crystallization and high BET surface area.     

Straightforward Synthesis of Mn3O4/ZnO/Eu2O3-Based Ternary Heterostructure Nano-Photocatalyst and Its Application for the Photodegradation of Methyl Orange and Methylene Blue Dyes

Zinc oxide-ternary heterostructure Mn₃O₄/ZnO/Eu₂O₃ nanocomposites were successfully prepared via waste curd as fuel by a facile one-pot combustion procedure. The fabricated heterostructures were characterized utilizing XRD, UV–Visible, FT-IR, FE-SEM, HRTEM and EDX analysis. The photocatalytic degradation efficacy of the synthesized ternary nanocomposite was evaluated utilizing model organic pollutants of methylene blue (MB) and methyl orange (MO) in water as examples of cationic dyes and anionic dyes, respectively, under natural solar irradiation. The effect of various experimental factors, viz. the effect of a light source, catalyst dosage, irradiation time, pH of dye solution and dye concentration on the photodegradation activity, was systematically studied. The ternary Mn₃O₄/ZnO/Eu₂O₃ photocatalyst exhibited excellent MB and MO degradation activity of 98% and 96%, respectively, at 150 min under natural sunlight irradiation. Experiments further conclude that the fabricated nanocomposite exhibits pH-dependent photocatalytic efficacy, and for best results, concentrations of dye and catalysts have to be maintained in a specific range. The prepared photocatalysts are exemplary and could be employed for wastewater handling and several ecological applications.     

BiOI/Bi2WO6对甲基橙和苯酚的光催化降解及光催化机理

采用简单的沉积方法制备了不同碘化氧铋含量的BiOI/Bi₂WO₆光催化剂,通过X射线衍射(XRD)、扫描电子显微镜(SEM)、高分辨透射电子显微镜(HR-TEM)、紫外-可见漫反射光谱(UV-VisDRS)和BET比表面积测量对其进行了表征。在紫外和可见光的照射下,使用甲基橙和苯酚的光催化降解评价了BiOI/Bi₂WO₆催化剂的光催化性能。结果表明：与商业P₂₅和纯Bi₂WO₆相比,13.2%BiOI/Bi₂WO₆光催化剂具有更高的紫外和可见光催化性能。这明显增加的光催化活性主要归功于光生电子和空穴在Bi₂WO₆和BiOI界面上的有效转移,降低了电子-空穴对的复合。基于BiOI和Bi₂WO₆的能带结构,提出了光生载流子的一种转移过程。自由基清除剂的实验表明,OH,h⁺,O₂和H₂O₂,特别是h⁺,共同支配了甲基橙和苯酚的光催化降解过程。     

Synthesis of TiO2/Bi2WO6 nanofibers with electrospinning technique for photocatalytic methyl blue degradation

TiO₂/Bi₂WO₆ composite nanofibers have been successfully synthesized by a simple electrospinning process. XRD, SEM, HR-TEM, nitrogen adsorption–desorption isotherms and UV–visible diffuse reflectance spectra were used to characterize the composite nanofibers. The composite fibers with diameters about 100 nm was composed of nanoparticles and possessed of high specific surface area (49.6 m² g^?1) and porous structure. Besides, the TiO₂/Bi₂WO₆ composite nanofibers exhibited excellent visible photocatalytic property in the photodegradation of methylene blue (MB), and over 97.2 % of MB was degraded within 5.5 h.     

Photocatalytic degradation of methylene blue and phenol on Fe-doped sulfated titania

Fe-doped sulfated titania (FST) photocatalysts with high photocatalytic activity were prepared from industrial titanyl sulfate solution and characterized using X-ray diffraction (XRD), thermogravimetry analysis?Cdifferential scanning calorimeter (TGA-DSC), Fourier transform infrared spectroscopy (FT-IR), and nitrogen adsorption?Cdesorption techniques. The photocatalytic activity of the FST photocatalyst was evaluated using the photodegradation of methylene blue (MB) and the photooxidation of phenol in aqueous solutions in the presence of UV irradiation, respectively. The effect of various parameters, such as calcining temperature, calcination time, initial concentration of substrate, amount of catalyst and pH value on the photocatalytic activity of FST photocatalyst was investigated. Among the parameters studied, calcining temperature, initial concentration of substrate, and amount of catalyst have a very similar effect on the activity of FST photocatalyst for both the photodegradation of MB and the photooxidation of phenol, while the others have distinct differences. The optimal calcination conditions were 500?°C, 1.5?h and 650?°C, 2.5?h; the optimal catalyst concentration were 1.0 and 1.2?g?L^?1; the optimal pH values were 8 and 4 for the photodegradation of MB and the photooxidation of phenol, respectively. In addition, the mechanism for the high photocatalytic efficiency of FST photocatalyst has also been put forward.     

漂浮型BiFeO3/膨胀珍珠岩的制备及其可见光催化性能

利用水热法制备了新颖的、漂浮型的膨胀珍珠岩(EP)负载BiFeO₃(BiFeO₃/EP)复合光催化材料。采用X射线衍射(XRD)、傅里叶变换红外光谱(FT-IR)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线光电子能谱仪(XPS)和紫外可见漫反射(UV-Vis-DRS)对制备的复合材料进行了表征与分析。SEM和TEM结果清楚地表明BiFeO₃纳米粒子已被负载到EP表面。与纯BiFeO₃相比,BiFeO₃/EP复合材料明显提高了对可见光的吸收能力,减小了带隙宽度,在可见光下对亚甲基蓝(MB)的降解表现出更强的光催化活性。其中,70%BiFeO₃/EP复合材料对MB染料废水的光催化活性最高,其光催化反应一级速率常数是纯BiFeO₃的2.2倍。由于质轻中空的特点,制备的BiFeO₃/EP颗粒漂浮在液面上,有利于相分离和反应后光催化剂的回收。材料的重复性试验表明,复合材料在MB光降解过程中是相当稳定的。     

Effective synthesis of nanoscale anatase TiO2 single crystals using activated carbon template to enhance the photodegradation of crystal violet

Nanoscale anatase TiO₂ single crystals were successfully synthesized using three kinds of activated carbon (AC) templates through a simple sol–gel method. The optimal photocatalyst (T‐WOAC) was obtained using wood‐based AC template. X‐ray diffraction, transmission electron microscopy and Brunauer–Emmett–Teller analyses revealed that T‐WOAC possessed a small crystallite size of 8.7 nm and a clear mesoporous structure. The photocatalytic properties of samples were then evaluated through photodegradation of crystal violet (CV). Results implied that the photocatalysts prepared using the AC templates exhibited superior photocatalytic activity to that of the original TiO₂. This enhancement may be due to the small crystallite size, large specific surface area and pore volume of the catalysts prepared with ACs. T‐WOAC showed high photocatalytic activity, CV degradation of 99.01% after 120 min of irradiation and k = 0.03914 min^?1, which is 3.9 times higher than that of the original TiO₂ (k = 0.00994 min^?1). This result can be mainly attributed to the application of WOAC with moderate specific surface area and pore volume to produce T‐WOAC. Alkaline conditions benefitted the photodegradation of CV over photocatalysts. This work proposes a possible degradation mechanism of CV and indicates that the fabricated photocatalysts can be used to effectively remove CV from aqueous solutions.     

可见光下具有高光子效应和光催化活性的CuS-石墨烯氧化物/TiO2复合材料的制备（英文）

CuS-graphene oxide/TiO2 composites were prepared using a sol-gel method to improve the photocatalytic performance of the photocatalyst. The composites were characterized by X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray analysis, and transmission electron microscopy. The photocatalytic activities were examined by the degradation of methylene blue (MB) under visible-light irradiation. The photodegradation of MB under visible-light irradiation reached 90.1% after 120 min. The kinetics of MB degradation was plotted alongside the values calculated from the Langmuir-Hinshelwood equation. The CuS-graphene oxide/TiO2 sample prepared using 0.2 mol of TiO2 showed the best photocatalytic activity. This was attributed to a cooperative reaction as a result of increased photoabsorption by graphene oxide and an increased photocatalytic effect by CuS.     

Novel hydrostable Z-scheme Ag/CsPbBr3/Bi2WO6 photocatalyst for effective degradation of Rhodamine B in aqueous solution

In this study, a hydrostable Z-scheme Ag/CsPbBr₃/Bi₂WO₆ photocatalyst was designed and fabricated for the degradation of Rhodamine B (RhB). The structural instability of CsPbX₃ perovskites in water is one of the main obstacles that restrict their practical application in photocatalytic wastewater treatment. The photocatalyst was prepared in three steps: passivation of CsPbBr₃ nanocrystals (NCs) with 3-mercaptopropionic acid (MPA), construction of a heterojunction between MPA-passivated CsPbBr₃ NCs and Bi₂WO₆ ultrathin nanosheets, and doping Ag nanoparticles as charge mediators in the heterojunction. The as-obtained 5%Ag/20%CsPbBr₃/Bi₂WO₆ exhibits good stability and excellent photocatalytic activity. The degradation rate is 93.9% in 120 min, which is 4.41 times than that of Bi₂WO₆.     

Preparation of Ag-loaded octahedral Bi2WO6 photocatalyst and its photocatalytic activity

In this work, an Ag-loaded octahedral Bi₂WO₆ photocatalyst has been successfully prepared by the hydrothermal method and photo deposition method. X-ray diffraction (XRD), energy dispersive analysis of X-ray (EDX), field-emission scanning electron microscopy (FE-SEM) and ultra-violet adsorption spectrum (UV-Vis) were employed for characterization of the composite photocatalyst. Furthermore, two different photocatalysts including the obtained Ag-loaded octahedral Bi₂WO₆ were employed here for photodegradation of model contaminated water of Orange II (OII). Results show that Ag-loaded Bi₂WO₆ photocatalyst exhibits superior photocatalytic properties compared to the undoped Bi₂WO₆. The reasons for improvement in photocatalytic activity of the Ag-loaded octahedral Bi₂WO₆ were also discussed.     

Preparation and characterization of a new CdS–NiFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/reduced graphene oxide photocatalyst and its use for degradation of methylene blue under visible light irradiation

In this paper, CdS nanoparticles as a visible light active photocatalyst were coupled by NiFe₂O₄ and reduced graphene oxide (rGO) to form CdS–NiFe₂O₄/rGO nanocomposite by facile hydrothermal methods. The CdS–NiFe₂O₄/rGO nanocomposite shows enhanced photocatalytic activity for the degradation of methylene blue (MB) under visible light illumination. In addition to improved photocatalytic performance, this prepared nanocomposite shows increased photostability and is magnetically separable from the aqueous media. The degradation rate constant (k_app) of the optimized photocatalyst, i.e. CdS–NiFe₂O₄ (0.05)/rGO 25 wt% nanocomposite, was higher than the corresponding CdS and NiFe₂O₄ nanoparticles by factors of 11.1 and 8.9, respectively. The synergistic interactions between CdS, NiFe₂O₄ and rGO lead to enhanced surface area, reduced aggregation of the nanoparticles, decreased the recombination of photogenerated electron–hole pairs, and increased the charge separation efficiency and effective electron–hole generation transfer. According to the obtained results, a proposed mechanism of the photodegradation of MB under visible light irradiation is finally mentioned.     

Ag3PO4/MoS2纳米片复合催化剂制备及可见光催化性能

采用机械球磨法成功制备Ag₃PO₄/MoS₂纳米片复合催化剂。运用X射线衍射仪（XRD）、透射电子显微镜（TEM）、扫描电子显微镜（SEM）、紫外可见漫反射光谱（UV-Vis）和荧光发射光谱（PL）对复合催化剂的结构和形貌进行了表征。结果表明,Ag₃PO₄纳米粒子均匀地附着在MoS₂纳米片层结构上,两者形成紧密结合。以亚甲基蓝为模拟污染物,研究复合催化剂在可见光照射下的光催化特性;通过循环实验考察复合催化剂的稳定性。结果显示,含有1%的MoS₂纳米片与Ag₃PO₄形成的复合催化剂在30 min内对亚甲基蓝的降解率为95%,其降解动力学常数是纯相Ag₃PO₄的2倍。经过5次循环实验后复合催化剂对于亚甲基蓝的降解率为84%,而纯Ag₃PO₄对于亚甲基蓝的降解率仅为35%。Ag₃PO₄/MoS₂纳米片复合催化剂具有优良的光催化活性和高稳定性,主要归因于二硫化钼纳米片与磷酸银形成异质结,磷酸银激发的电子和二硫化钼纳米片产生的空穴直接复合,从而促使光生电子从磷酸银晶体表面快速分离,减轻了磷酸银的光电子腐蚀,同时也提高了复合物的光催化活性。     

Facile synthesis of Z-scheme NiO/α-MoO3 p-n heterojunction for improved photocatalytic activity towards degradation of methylene blue

In this article, Z-scheme NiO/α-MoO₃ p-n heterojunction is successfully synthesized by a facile hydrothermal route. The phase and nanostructures are researched through a series of characterizations, such as XRD, SEM, TEM, EDX, XPS and DRS. It is confirmed that the NiO nanoparticles are deposited homogeneously on one dimensional α-MoO₃ nanobelts and p-n heterojuction is constructed at the interface of α-MoO₃ and NiO. Photocatalytic activity of the as-synthesized photocatalysts is investigated by photodegradation of methylene blue (MB) under simulated solar light irradiation. Compared with bare α-MoO₃, the NiO/α-MoO₃ p-n heterojunction exhibits significantly improved photocatalytic activity and photostability for MB degradation. The improvement in the photocatalytic performance can be attributed to the optimization of the charge transport pathway offered by Z-scheme heterojunctions, which can promote the effective separation of electron-hole pairs. The results indicate that Z-scheme NiO/α-MoO₃ p-n heterojunction is a novel and efficient photocatalyst with potential application for the removal of organic contaminant in wastewater.     

Ag_3PO_4/MoS_2纳米片复合催化剂制备及可见光催化性能

采用机械球磨法成功制备Ag_3PO_4/MoS_2纳米片复合催化剂。运用X射线衍射仪(XRD)、透射电子显微镜(TEM)、扫描电子显微镜(SEM)、紫外可见漫反射光谱(UV-Vis)和荧光发射光谱(PL)对复合催化剂的结构和形貌进行了表征。结果表明,Ag_3PO_4纳米粒子均匀地附着在MoS_2纳米片层结构上,两者形成紧密结合。以亚甲基蓝为模拟污染物,研究复合催化剂在可见光照射下的光催化特性;通过循环实验考察复合催化剂的稳定性。结果显示,含有1%的MoS_2纳米片与Ag_3PO_4形成的复合催化剂在30 min内对亚甲基蓝的降解率为95%,其降解动力学常数是纯相Ag_3PO_4的2倍。经过5次循环实验后复合催化剂对于亚甲基蓝的降解率为84%,而纯Ag_3PO_4对于亚甲基蓝的降解率仅为35%。Ag_3PO_4/MoS_2纳米片复合催化剂具有优良的光催化活性和高稳定性,主要归因于二硫化钼纳米片与磷酸银形成异质结,磷酸银激发的电子和二硫化钼纳米片产生的空穴直接复合,从而促使光生电子从磷酸银晶体表面快速分离,减轻了磷酸银的光电子腐蚀,同时也提高了复合物的光催化活性。     

BiOI/Bi_2WO_6对甲基橙和苯酚的光催化降解及光催化机理(英文)

采用简单的沉积方法制备了不同碘化氧铋含量的BiOI/Bi2WO6光催化剂,通过X射线衍射(XRD)、扫描电子显微镜(SEM)、高分辨透射电子显微镜(HR-TEM)、紫外-可见漫反射光谱(UV-Vis DRS)和BET比表面积测量对其进行了表征。在紫外和可见光的照射下,使用甲基橙和苯酚的光催化降解评价了BiOI/Bi2WO6催化剂的光催化性能。结果表明:与商业P25和纯Bi2WO6相比,13.2%BiOI/Bi2WO6光催化剂具有更高的紫外和可见光催化性能。这明显增加的光催化活性主要归功于光生电子和空穴在Bi2WO6和BiOI界面上的有效转移,降低了电子-空穴对的复合。基于BiOI和Bi2WO6的能带结构,提出了光生载流子的一种转移过程。自由基清除剂的实验表明,·OH,h+,·O2-和H2O2,特别是h+,共同支配了甲基橙和苯酚的光催化降解过程。     

A Novel N-Doped Nanoporous Bio-Graphene Synthesized from Pistacia lentiscus Gum and Its Nanocomposite with WO3 Nanoparticles: Visible-Light-Driven Photocatalytic Activity

This paper reports the synthesis of a new nitrogen-doped porous bio-graphene (NPBG) with a specific biomorphic structure, using Pistacia lentiscus as a natural carbon source containing nitrogen that also acts as a bio-template. The obtained NPBG demonstrated the unique feature of doped nitrogen with a 3D nanoporous structure. Next, a WO₃/N-doped porous bio-graphene nanocomposite (WO₃/NPBG-NC) was synthesized, and the products were characterized using XPS, SEM, TEM, FT-IR, EDX, XRD, and Raman analyses. The presence of nitrogen doped in the structure of the bio-graphene (BG) was confirmed to be pyridinic-N and pyrrolic-N with N1 peaks at 398.3 eV and 400.5 eV, respectively. The photocatalytic degradation of the anionic azo dyes and drugs was investigated, and the results indicated that the obtained NPBG with a high surface area (151.98 m²/g), unique electronic properties, and modified surface improved the adsorption and photocatalytic properties in combination with WO₃ nanoparticles (WO₃-NPs) as an effective visible-light-driven photocatalyst. The synthesized WO₃/NPBG-NC with a surface area of 226.92 m²/g displayed lower bandgap and higher electron transfer compared with blank WO₃-NPs, leading to an increase in the photocatalytic performance through the enhancement of the separation of charge and a reduction in the recombination rate. At the optimum conditions of 0.015 g of the nanocomposite, a contact time of 15 min, and 100 mg/L of dyes, the removal percentages were 100%, 99.8%, and 98% for methyl red (MR), Congo red (CR), and methyl orange (MO), respectively. In the case of the drugs, 99% and 87% of tetracycline and acetaminophen, respectively, at a concentration of 10 mg/L, were removed after 20 min.