On-line preconcentration and separation of Co, Ni and Cd via capillary microextraction on ordered mesoporous alumina coating and determination by inductively plasma mass spectrometry (ICP-MS)

In this paper, an ordered mesoporous alumina coating was prepared and applied to capillary microextraction (CME) of trace Co, Ni and Cd for the first time. The coated capillary was used for on-line coupling CME with inductively plasma mass spectrometry (ICP-MS) for the determination of trace metals of Co, Ni and Cd. The porous structure of Al₂O₃ coating was examined by SEM and TEM. The effects of the extraction parameters including pH, sample flow rate and volume, elution solution and interfering ions on the recovery of analytes have been investigated and optimized. Under the optimized conditions, the limits of detection were 0.33, 1.5 and 1.4 ng L⁻¹ for Co, Ni and Cd, respectively, with a preconcentration factor of 10 times. The precisions for all investigated elements were 2.7, 4.1 and 2.5% (c = 0.05 ng L⁻¹, n = 7), for Co, Ni and Cd, respectively, and the sample frequency was 8 h⁻¹.The proposed method was successfully applied for the analysis of trace metals in water, rice and urine samples with the recovery of 94-105%. In order to validate the proposed method, two certified reference materials of GBW 0913 human urine and NIES No.10-b rice flour were analyzed, and the determination values are in good agreement with the certified values. The ordered mesoporous Al₂O₃ coated capillary can be used more than 20 times without decreasing the extraction efficiency.     

Determination of 36 elements in plant reference materials with different Si contents by inductively coupled plasma mass spectrometry: comparison of microwave digestions assisted by three types of digestion mixtures

Closed-vessel microwave digestion of nine standard reference plant materials (NIST, BCR, IAEA) and a laboratory standard of plant material with different Si contents assisted by HNO₃ + H₂O₂ (procedure A), HNO₃ + H₂O₂ + HF + H₃BO₃ (procedure B) and HNO₃ + H₂O₂ + HBF₄ (procedure C) were used to determine the recovery of 36 elements by ICP-MS: Ag, Al, As, Ba, Be, Bi, Cd, Ce, Co, Cr, Cs, Cu, Fe, Ga, Ge, In, La, Li, Mn, Mo, Nd, Ni, Pb, Pr, Rb, Sb, Se, Sn, Sr, Th, Tl, U, V, W, Y, Zn. Additions of HF + H₃BO₃ and HBF₄ in procedures B and C exceeded by 10% (B1, C1) and 100% (B2, C2) the equivalent concentrations of Si in the samples determined by ICP-OES. Most recoveries of certified elements (e.g., Al^*, Cu, Mo^*, Rb^*, Sb^*, Th) decreased significantly (^*p ≤ 0.05) with increasing Si content in plant reference materials digested by procedure A, while the recoveries from procedures B and C decreased insignificantly only for Mo and Sb. Digestions B and C gave significantly higher recoveries of Al, Sb, W and REEs, which were tighter to the reference values of these elements. A similar effect was found for Cu, Fe, Li, Ni, Sn, Th, Tl, V, Zn, Ba, Rb and Sr recoveries in samples with Si contents exceeding 2000 μg g⁻¹. If the Si content in plant samples is less than 10 mg g⁻¹, digestion of 0.5 g of plant samples through 0.05 mL of HF and 0.5 mL of 4% H₃BO₃ or 0.1 mL of HBF₄ is recommended to get satisfactory results for most of the elements. For materials with Si content exceeding 10 mg g⁻¹ the weight of the sample for digestion should be reduced to 0.25 g. However, the operation of potential interferences should be taken into account and eliminated through correction equations and adequate dilution of the samples.     

A portable and low cost equipment for flow injection chemiluminescence measurements

A compact, reliable and low cost flow injection chemiluminescence system is described. The flow system consists of a set of solenoid micro-pumps that can dispense reproductive micro-volumes of solutions. The luminometer was based on a coiled cell constructed from polyethylene tubing that was sandwiched between two large area photodiodes. The whole equipment costs about US$ 750 and weights ca. 3 kg. Equipment performance was evaluated by measuring low concentrations of hydrogen peroxide by oxidation of luminol and for the determination of ammonium, based on its inhibition of the luminescence provided by the reaction of luminol and sodium hypochlorite. Linear responses were achieved within 1.0-80 μmol L⁻¹ H₂O₂ and 0.6-60 μmol L⁻¹ NH₄⁺ with detection limits estimated as 400 nmol L⁻¹ H₂O₂ and 60 nmol L⁻¹ NH₄⁺ at the 99.7% confidence level. Coefficients of variation were 1.0 and 1.8%, estimated for 20 μmol L⁻¹ H₂O₂ and 15 μmol L⁻¹ NH₄⁺ (n = 20), respectively. Reagent consumption of 55 μg luminol, effluent volume of 950 μL per determination and sampling rate of 120 samples per hour were also achieved.     

Series of compositions Bi2(M′xM1−x)4O9 (M′, M=Al, Ga, Fe; 0≤x≤1) with mullite-type crystal structure: Synthesis, characterization and O/O exchange experiment

Series of compositions Bi₂(M′_xM_1−x)₄O₉ with x=0.0, 0.1,…, 1.0 and M′/M=Ga/Al, Fe/Al and Fe/Ga were synthesized by dissolving appropriate amounts of corresponding metal nitrate hydrates in glycerine, followed by gelation, calcination and final heating at 800 °C for 24 h. The new compositions with M′/M=Ga/Al form solid-solution series, which are isotypes to the two other series M′/M=Fe/Al and Fe/Ga. The XRD data analysis yielded in all cases a linear dependence of the lattice parameters related on x. Rietveld structure refinements of the XRD patterns of the new compounds, Bi₂(Ga_xAl_1−x)₄O₉ reveal a preferential occupation of Ga in tetrahedral site (4 h). The IR absorption spectra measured between 50 and 4000 cm⁻¹ of all systems show systematic shifts in peak positions related to the degree of substitution. Samples treated in ¹⁸O₂ atmosphere (16 h at 800 °C, 200 mbar, 95% ¹⁸O₂) for ¹⁸O/¹⁶O isotope exchange experiments show a well-separated IR absorption peak related to the M-¹⁸O_c-M vibration, where O_c denotes the common oxygen of two tetrahedral type MO₄ units. The intensity ratio of M-¹⁸O_c/M-¹⁶O_c IR absorption peaks and the average crystal sizes were used to estimate the tracer diffusion coefficients of polycrystalline Bi₂Al₄O₉ (D=2×10⁻²² m²s⁻¹), Bi₂Fe₄O₉ (D=5×10⁻²¹ m²s⁻¹), Bi₂(Ga/Al)₄O₉ (D=2×10⁻²¹ m²s⁻¹) and Bi₂Ga₄O₉ (D=2×10⁻²⁰ m²s⁻¹).     

Chlorine and sulfur determination in extra-heavy crude oil by inductively coupled plasma optical emission spectrometry after microwave-induced combustion

In this study, microwave-induced combustion (MIC) of extra-heavy crude oil is proposed for further chlorine and sulfur determination by inductively coupled plasma optical emission spectrometry (ICP OES). Combustion was carried out under oxygen pressure (20 bar) in quartz vessels using ammonium nitrate (50 µl of 6 mol l^− 1 solution) as ignition aid. Samples were wrapped with polyethylene film and placed on a quartz holder positioned inside the quartz vessels. The need for an additional reflux step after combustion and the type and concentration of absorbing solution (water, 0.02 to 0.9 mmol l^− 1 H₂O₂, 10 to 100 mmol l^− 1 (NH₄)₂CO₃ or 0.1 to 14 mol l^− 1 HNO₃) were studied. The influence of sample mass, O₂ pressure and maximum pressure attained during the combustion process were investigated. Recoveries from 92 to 102% were obtained for Cl and S for all absorbing solutions. For comparison, Cl and S determination was also performed by ion chromatography (IC) using 25 mmol l^− 1 (NH₄)₂CO₃ as absorbing solution. Using MIC with a reflux step the agreement was better than 95% for certified reference materials of similar composition (crude oil, petroleum coke, coal and residual fuel oil). Microwave-assisted digestion and water extraction in high pressure closed vessels were also evaluated. Using these procedures the maximum recoveries were 30 and 98% for Cl and S, respectively, using microwave-assisted digestion and 70% for Cl and less than 1% for S by water extraction procedure. Limits of detection by ICP OES were 12 and 5 µg g^− 1 for Cl and S, respectively, and the corresponding values by IC were 1.2 and 8 µg g^− 1. Using MIC it was possible to digest simultaneously up to eight samples resulting in a solution suitable for the determination of both analytes with a single combustion step.     

Synthesis and textural evolution of alumina particles with mesoporous structures

Alumina particles with mesostructures were synthesized through a chemical precipitation method by using different inorganic aluminum salts followed by a heterogeneous azeotropic distillation and calcination process. The obtained mesoporous γ-alumina particles were systematically characterized by the X-ray diffraction, transmission electron microscopy and nitrogen adsorption-desorption measurement. Effects of the aluminum salt counter anion, pH value and the azeotropic distillation process on the structural or textural evolution of alumina particles were investigated. It is found that Cl⁻ in the reaction solution can restrain the textural evolution of the resultant precipitates into two-dimensional crystallized pseudoboehmite lamellae during the heterogeneous azeotropic distillation, and then transformed into γ-Al₂O₃ particles with mesostructures after further calcination at 1173 K, whereas coexisting SO₄²⁻ can promote above morphology evolution and then transformed into γ-Al₂O₃ nanofibers after calcination at 1173 K. Moreover nearly all materials retain relatively high specific surface areas larger than 100 m² g⁻¹ even after calcinations at 1173 K.     

Solid phase extraction of trace Hg(II) on silica gel modified with 2-(2-oxoethyl)hydrazine carbothioamide and determination by ICP-AES

In this work, a new 2-(2-oxoethyl)hydrazine carbothioamide modified silica gel (SG-OHC) sorbent was prepared and applied for preconcentration of trace mercury(II) prior to the measurement by inductively coupled plasma atomic emission spectrometry (ICP-AES). The optimization of some analytical parameters affecting the adsorption of the analyte such as acidity, shaking time, sample flow rate and volume, eluent condition, and interfering substances were investigated. At pH 3, the maximum static adsorption capacity of Hg(II) onto the SG-OHC was 37.5 mg g⁻¹. The quantitative recovery (>95%) of Hg(II) could be obtained using 2 mL of 0.5 mol L⁻¹ HCl and 1% CS(NH₂)₂ solution as eluent. Common coexisting substances did not interfere with the separation of mercury(II) under optimal conditions. The detection limit of present method was 0.10 ng mL⁻¹, and the relative standard deviation (RSD) was lower than 4.0% (n = 8). The prepared sorbent was successfully applied for the preconcentration of trace Hg(II) in certified and water samples with satisfactory results.     

The effects of ZnGa2O4 formation on structural and optical properties of ZnO:Ga powders

Gallium-doped zinc oxide (ZnO:Ga 1, 2, 3, 4 and 5 at%) samples were prepared in powder form by modifying the Pechini method. The formation of zinc gallate (ZnGa₂O₄) with the spinel crystal structure was observed even in ZnO:Ga 1 at% by X-ray diffraction. The presence of ZnGa₂O₄ in ZnO:Ga samples was also evidenced by luminescence spectroscopy through its blue emission at 430 nm, assigned to charge transfer between Ga³⁺ at regular octahedral symmetry and its surrounding O²⁻ ions. The amount of ZnGa₂O₄ increases as the dopant concentration increases, as observed by the quantitative phase analysis by the Rietveld method.     

Adsorption studies of Cd(II) onto Al2O3/Nb2O5 mixed oxide dispersed on silica matrix and its on-line preconcentration and determination by flame atomic absorption spectrometry

The present study describes the adsorption characteristic of Cd(II) onto Nb₂O₅/Al₂O₃ mixed oxide dispersed on silica matrix. The characterization of the adsorbent has been carried out by infrared spectroscopy (IR), scanning electronic microscopy (SEM), energy dispersive spectroscopy (EDS), energy dispersive X-ray fluorescence analysis (EDXRF) and specific surface area (S_BET). From batch experiments, adsorption kinetic of Cd(II) was described by a pseudo-second-order kinetic model. The Langmuir linear isotherm fitted to the experimental adsorption isotherm very well, and the maximum adsorption capacity was found to be 17.88 mg g⁻¹. Using the effective material, a method for Cd(II) preconcentration at trace level was developed. The method was based on on-line adsorption of Cd(II) onto SiO₂/Al₂O₃/Nb₂O₅ at pH 8.64, in which the quantitative desorption occurs with 1.0 mol L⁻¹ hydrochloric acid towards FAAS detector. The experimental parameters related to the system were studied by means of multivariate analysis, using 2⁴ full factorial design and Doehlert matrix. The effect of SO₄²⁻, Cu²⁺, Zn²⁺ and Ni²⁺ foreign ions showed no interference at 1:100 analyte:interferent proportion. Under the most favorable experimental conditions, the preconcentration system provided a preconcentration factor of 18.4 times, consumption index of 1.08 mL, sample throughput of 14 h⁻¹, concentration efficiency of 4.35 min⁻¹, linear range from 5.0 up to 35.0 μg L⁻¹ and limits of detection and quantification of 0.19 and 0.65 μg L⁻¹ respectively. The feasibility of the proposed method for Cd(II) determination was assessed by analysis of water samples, cigarette sample and certified reference materials TORT-2 (Lobster hepatopancreas) and DOLT-4 (Dogfish liver).     

Extraction of trace amounts of mercury with sodium dodecyle sulphate-coated magnetite nanoparticles and its determination by flow injection inductively coupled plasma-optical emission spectrometry

A new method for solid-phase extraction and preconcentration of trace amounts Hg(II) from environmental samples was developed by using sodium dodecyle sulphate-coated magnetite nanoparticles (SDS-coated Fe₃O₄ NPs) as a new extractant. The procedure is based on the adsorption of the analyte, as mercury-Michler's thioketone [Hg₂(TMK)₄]²⁺ complex on the negatively charged surface of the SDS-coated Fe₃O₄ NPs and then elution of the preconcentrated mercury from the surface of the SDS-coated Fe₃O₄ NPs prior to its determination by flow injection inductively coupled plasma-optical emission spectrometry. The effects of pH, TMK concentration, SDS and Fe₃O₄ NPs amounts, eluent type, sample volume and interfering ions on the recovery of the analyte were investigated. Under optimized conditions, the calibration curve was linear in the range of 0.2-100 ng mL⁻¹ with r² = 0.9994 (n = 8). The limit of detection for Hg(II) determination was 0.04 ng mL⁻¹. Also, relative standard deviation (R.S.D.) for the determination of 2 and 50 ng mL⁻¹ of Hg(II) was 5.2 and 4.7% (n = 6), respectively. Due to the quantitative extraction of Hg(II) from 1000 mL of the sample solution an enhancement factor as large as 1230-fold can be obtained. The proposed method has been validated using a certified reference materials, and also the method has been applied successfully for the determination of Hg(II) in aqueous samples.     

Modified mesoporous silica materials for on-line separation and preconcentration of hexavalent chromium using a microcolumn coupled with flame atomic absorption spectrometry

A modified SBA-15 mesoporous silica material NH₂-SBA-15 was synthesized successfully by grafting γ-aminopropyl-triethoxysilane. The material was characterized using transmission electron microscopy (TEM) and Fourier transform infrared/Raman (FT-IR/Raman) spectroscopy, and used for the first time in a flow injection on-line solid phase extraction (SPE) coupled with flame atomic absorption spectrometry (FAAS) to detect trace Cr (VI). Effective sorption of Cr (VI) was achieved at pH 2.0 with no interference from Cr (III) and other ions and 0.5 mol L⁻¹ NH₃·H₂O solution was found optimal for the complete elution of Cr (VI). An enrichment factor of 44 and was achieved under optimized experimental conditions at a sample loading of 2.0 mL min⁻¹ sample loading (300 s) and an elution flow rate of 2.0 mL min⁻¹ (24 s). The precision of the 11 replicate Cr (VI) measurements was 2.1% at the 100 μg L⁻¹ level with a detection limit of 0.2 μg L⁻¹ (3 s, n = 10) using the FAAS. The developed method was successfully applied to trace chromium determination in waste water. The accuracy was validated using a certified reference material of riverine water (GBW08607).     

Synthesis, characterization and application of a novel mercapto- and amine-bifunctionalized silica for speciation/sorption of inorganic arsenic prior to inductively coupled plasma mass spectrometric determination

A bifunctional sorbent, (NH₂ + SH)silica, containing both amine and mercapto functionalities was prepared by modification of silica gel with 3-(triethoxysilyl)propylamine and (3-mercaptopropyl)trimethoxysilane. In addition to the bifunctional sorbent, silica gel was modified individually with the functional mercapto- and amino-silanes, and the mono-functional sorbents, namely (SH)silica and (NH₂)silica, were also mechanically mixed ((NH₂)silica + (SH)silica) for the sake of comparison of sorption performances. It has been demonstrated that (SH)silica shows quantitative sorption only to As(III) at two pH values, 1.0 and 9.0, while (NH₂)silica displays selectivity only towards As(V) at pH 3.0. On the other hand, the bifunctional (NH₂ + SH)silica possesses the efficient features of the two mono-functionalized sorbents; for example, it retains As(III) at a wider pH range, from 1.0 to at least 9.0 with the exception at pH 2.0, and it also shows quantitative sorption to As(V) at pH 3.0. This property gives the bifunctional (NH₂ + SH)silica a better flexibility in terms of sorption performance as a function of solution pH. The mechanically mixed (NH₂)silica + (SH)silica exhibits a similar but less efficient sorption behavior compared to the bifunctional sorbent. Desorption of both As(III) and As(V) species can be realized using 0.5 M NaOH. The validity of the proposed method was checked through the analysis of a standard reference material and a good correlation was obtained between the certified (26.67 μg L⁻¹) and determined (27.53 ± 0.37 μg L⁻¹) values. Spike recovery tests realized with ultrapure water (93.0 ± 2.3%) and drinking water (86.9 ± 1.2%) also confirmed the applicability of the method.     

A study of the direct determination of Cd, Cr, Cu, Pb and Zn in certified reference materials of soils by solid sampling electrothermal atomic absorption spectrometry

A simple and rapid method for the direct determination of Cd, Cr, Cu, Pb and Zn in soil was developed. The method was developed using three certified reference materials of soil: Eutric Cambisol, Orthic Luvisols and Rendzina, which differed in their matrix composition. Chemical modifiers were essential to achieve reproducible and interference-free signals for the analytes studied. The best results were obtained with a Pd/Mg(NO₃)₂ admixture for the determination of Cd, Pb and Zn and NH₄F for Cu. The combination of W (as a permanent modifier) and Mg(NO₃)₂ provided well-defined signal profiles for Cr. The following spectral lines were used: Cd 228.8 nm, Cr 520.6 nm, Cu 218.2 nm, Pb 205.3 nm and Zn 307.6 nm. The limit of detection was 4.2 ng g^− 1 for Cd, 1.1 μg g^− 1 for Cr, 0.5 μg g^− 1 for Cu, 1.3 μg g^− 1 for Pb and 8.6 μg g^− 1 for Zn for the maximum sample mass used. Under optimized conditions, the analyte and matrix were separated effectively in situ, and aqueous standards could be used for calibration.     

Improved determination of selenium in plant and peat samples using hydride generation-atomic fluorescence spectrometry (HG-AFS)

A robust, accurate and sensitive analytical procedure for the determination of Se in plant and peat samples by hydride generation-atomic fluorescence spectrometry (HG-AFS) was developed. Aliquots (200 mg) of dried samples were digested with 3 mL nitric acid and 0.5 mL hydrogen peroxide in closed, pressurized PTFE vessels in a microwave oven at 220 °C. Addition of HBF₄ or HF to the digestion mixture was not required because experiments demonstrated that Se was not hosted in the silicate fraction of the investigated sample matrices. Selenium(VI) was directly reduced to Se(IV) in the undiluted digestion solutions after addition of 3.8 mL of 4 M HCl in a microwave oven at 103 °C for 3 min. Other reduction reagents, such as hydroxylamine hydrochloride or urea, were not necessary to cope with potential interferences from nitrogen oxides that could hamper the reliable determination of Se by HG-AFS. Optimum hydride generation of Se was achieved by using 0.9% NaBH₄ and 4.5 M HCl. A solution detection limit of 11 ng L⁻¹ was obtained under the optimized experimental conditions which corresponds to a method detection limit of 2.8 ng g⁻¹ in solid peat and plant materials. The precision of replicate measurements was better than 3% at Se concentrations of 50 ng L⁻¹. The analytical procedure was critically evaluated by analysing two certified plant reference materials (SRM 1515 Apple Leaves and SRM 1547 Peach Leaves) as well as three peat reference materials. Excellent agreement between the experimental values ranging from 50 ng g⁻¹ to ∼2 μg g⁻¹ and the certified concentrations was obtained.     

Synthesis, characterization, thermal stability and electrochemical properties of poly-4-[(2-methylphenyl)iminomethyl]phenol

In this study, the reaction conditions of poly-4-[(2-methylphenyl)iminomethyl]phenol (P-2-MPIMP) were studied by using oxidants such as air O₂, H₂O₂ and NaOCl in an aqueous alkaline medium between 50 and 90 °C. The structures of the synthesized monomer and polymer were confirmed by FT-IR, UV-vis, NMR and elemental analysis. The characterization was made by TG-DTA, size exclusion chromatography (SEC) and solubility tests. At the optimum reaction conditions, the yield of poly-4-[(2-methylphenyl)iminomethyl]phenol (P-2-MPIMP) was found to be 20% (for air O₂ oxidant), 33% (for H₂O₂ oxidant), and 74% (for NaOCl oxidant). According to the SEC analysis, the number-average molecular weight (M_n), weight-average molecular weight (M_w) and polydispersity index (PDI) values of P-2-MPIMP were found to be 3300, 4100 g mol⁻¹ and 1.242, using H₂O₂, and 4550, 5150 g mol⁻¹and 1.132, using air O₂ and 5300, 5850 g mol⁻¹ and 1.104, using NaOCl, respectively. According to TG analysis, the weight losses of 4-[(2-methylphenyl)iminomethyl]phenol (2-MPIMP) and P-2-MPIMP were found to be between 75.29% and 48.17% at 1000 °C, respectively. P-2-MPIMP was shown to have a higher stability against thermal decomposition. Also, electrical conductivity of the P-2-MPIMP was measured, showing that the polymer is a typical semiconductor. Electrochemically, the highest occupied molecular orbital (HOMO), the lowest unoccupied molecular orbital (LUMO) and electrochemical energy gaps ( of 2-MPIMP and P-2-MPIMP were found to be −6.01, −6.03; −2.63, −2.82; 3.38 and 3.21 eV, respectively. According to UV-vis measurements, the optical band gap (E_g) of 2-MPIMP and P-2-MPIMP was found to be 3.40 and 2.97 eV, respectively.     

Layer by layer assembly of catalase and amine-terminated ionic liquid onto titanium nitride nanoparticles modified glassy carbon electrode: Study of direct voltammetry and bioelectrocatalytic activity

A novel, simple and facile layer by layer (LBL) approach is used for modification of glassy carbon (GC) electrode with multilayer of catalase and nanocomposite containing 1-(3-Aminopropyl)-3-methylimidazolium bromide (amine terminated ionic liquid (NH₂-IL)) and titanium nitride nanoparticles (TiNnp). First a thin layer of NH₂-IL is covalently attached to GC/TiNnp electrode using electro-oxidation method. Then, with alternative self assemble positively charged NH₂-IL and negatively charged catalase a sensitive H₂O₂ biosensor is constructed, whose response is directly correlated to the number of bilayers. The surface coverage of active catalase per bilayer, heterogeneous electron transfer rate constant (k_s) and Michaelis–Menten constant (K_M) of immobilized catalase were 3.32 × 10⁻¹² mol cm⁻², 5.28 s⁻¹ and 1.1 mM, respectively. The biosensor shows good stability, high reproducibility, long life-time, and fast amperometric response with the high sensitivity of 380 μA mM⁻¹ cm⁻² and low detection limit of 100 nM at concentration range up to 2.1 mM.     

Quantum chemical study of the bond orders in the ruthenium,diruthenium and dirhodium nitrosyl complexes

Density functional calculations with the B3LYP functional were carried out for the [Ru(NO)Cl₅]²⁻, [Ru(NO)(NH₃)₅]³⁺, [Ru(NO)(CN)₅]²⁻, [Ru(NO)(CN)₅]³⁻, [Ru(NO)(hedta)]^q (hedta = N-(hydroxyethyl)ethylenediaminetriacetate triple-charged anion; q = 0, −1, −2), Rh₂(O₂CR)₄, Rh₂(O₂CR)₄(NO)₂, Ru₂(O₂CR)₄, Ru₂(O₂CR)₄(NO)₂, Ru₂(dpf)₄, and Ru₂(dpf)₄(NO)₂ (dpf = N,N′-diphenylformamidinate ion; R = H, CH₃, CF₃) complexes. The electronic structure was analyzed in terms of Mayer and Wiberg bond order indices. The technique of bond order indices decomposition into σ-, π-, and δ-contributions was proposed.     

Syntheses and characterization of ANi(AsF6)3 (A = H3O, O2, NO, NH4, K, Rb, and Cs) compounds

ANi(AsF₆)₃ (A = O₂⁺, NO⁺, NH₄⁺) compounds could be prepared by reaction between corresponding AAsF₆ salts and Ni(AsF₆)₂. When mixtures of AF (A = Li, Na, K, Rb, Cs) and NiF₂ are dissolved in aHF acidified with an excess of AsF₅ the corresponding AAsF₆ and Ni(AsF₆)₂ were formed in situ. For A = Li and Na only mixtures of AAsF₆ and Ni(AsF₆)₂ were obtained, while for A = K, Rb and Cs, the final products were ANi(AsF₆)₃ (A = K-Cs) compounds contaminated with AAsF₆ (A = K-Cs) and Ni(AsF₆)₂.ANi(AsF₆)₃ (A = H₃O⁺, O₂⁺, NO⁺, NH₄⁺ and K⁺) compounds are structurally related to previously known H₃OCo(AsF₆)₃. The main features of the structure of these compounds are rings of NiF₆ octahedra sharing apexes with AsF₆ octahedra connected into infinite tri-dimensional network. In this arrangement cavities are formed where single charged cations are placed.In O₂Ni(AsF₆)₃ the vibrational band belonging to O₂⁺ vibration is found at 1866 cm⁻¹, which is according to the literature data one of the highest known values, and it is only 10 cm⁻¹ lower than the value for free O₂⁺.     

Heat capacity, enthalpy and entropy of ternary bismuth tantalum oxides

Heat capacity and enthalpy increments of ternary bismuth tantalum oxides Bi₄Ta₂O₁₁, Bi₇Ta₃O₁₈ and Bi₃TaO₇ were measured by the relaxation time method (2-280 K), DSC (265-353 K) and drop calorimetry (622-1322 K). Temperature dependencies of the molar heat capacity in the form C_pm=445.8+0.005451T−7.489×10⁶/T² J K⁻¹ mol⁻¹, C_pm=699.0+0.05276T−9.956×10⁶/T² J K⁻¹ mol⁻¹ and C_pm=251.6+0.06705T−3.237×10⁶/T² J K⁻¹ mol⁻¹ for Bi₃TaO₇, Bi₄Ta₂O₁₁ and for Bi₇Ta₃O₁₈, respectively, were derived by the least-squares method from the experimental data. The molar entropies at 298.15 K, S°_m(298.15 K)=449.6±2.3 J K⁻¹ mol⁻¹ for Bi₄Ta₂O₁₁, S°_m(298.15 K)=743.0±3.8 J K⁻¹ mol⁻¹ for Bi₇Ta₃O₁₈ and S°_m(298.15 K)=304.3±1.6 J K⁻¹ mol⁻¹ for Bi₃TaO₇, were evaluated from the low-temperature heat capacity measurements.     

Synthesis and thermochemistry of SrB2O4·4H2O and SrB2O4

Two pure strontium borates SrB₂O₄·4H₂O and SrB₂O₄ have been synthesized and characterized by means of chemical analysis and XRD, FT-IR, DTA-TG techniques. The molar enthalpies of solution of SrB₂O₄·4H₂O and SrB₂O₄ in 1 mol dm⁻³ HCl(aq) were measured to be −(9.92 ± 0.20) kJ mol⁻¹ and −(81.27 ± 0.30) kJ mol⁻¹, respectively. The molar enthalpy of solution of Sr(OH)₂·8H₂O in (HCl + H₃BO₃)(aq) were determined to be −(51.69 ± 0.15) kJ mol⁻¹. With the use of the enthalpy of solution of H₃BO₃ in 1 mol dm⁻³ HCl(aq), and the standard molar enthalpies of formation for Sr(OH)₂·8H₂O(s), H₃BO₃(s), and H₂O(l), the standard molar enthalpies of formation of −(3253.1 ± 1.7) kJ mol⁻¹ for SrB₂O₄·4H₂O, and of −(2038.4 ± 1.7) kJ mol⁻¹ for SrB₂O₄ were obtained.