Mixed conductive electrode materials for sensors and SOFC

Modified active electrode materials based upon rare earth manganites were developed for different solid electrolyte electrochemical cells. The preparation, structure, thermal expansion, the state of oxygen on the surface, the electronic and ionic conductivity of the perovskites Ln_1−xCa(Sr)_xMn_1−y(Co, Ni)_yO_3−δ with various compositions and electrode kinetics on the manganite electrode/solid electrolyte interfaces were investigated. The value of the bulk conductivity was larger than 150 S/cm (at 1100 K) and increased significantly with increasing contents of Ni or Co. The thermal expansion coefficients of rare earth manganites were close to those of ZrO₂ based solid electrolytes. The expansion coefficients of Co or Ni subsituted lanthanum manganites increase with Co or Ni substitution and are over 12•10⁻⁶K⁻¹. The ionic conductivities were determined using encapsulated zirconia microelectrodes based on a Hebb-Wagner analysis of the currentvoltage curves. The relatively high oxide ion conductivity of 10⁻⁵ S/cm at 900...1000 K was found by Ni or Co doped manganites. Studies of the electrode kinetics using complex impedance spectroscopy show that Co and Ni doped manganites have advantages if used as electrodes as compared with these for noble metals. Paper presented at the 1st Euroconference on Solid State Ionics, Zakynthos, Greece, 11–18 Sept. 1994     

Raman Spectra of Alkali and Alkaline Earth Metal Salts of Inosine 5′-Monophosphoric Acid

Crystalline Li(I), Na(I), K(I), Mg(II), Ca(II), Sr(II), Ba(II) and Cd(II) salts of inosine 5′-monophosphoric acid, H₂(IMP), were obtained and characterized by Raman spectroscopy. Splitting of the imidazolic 1480 cm⁻¹ band was observed for the N(7)-bound Ca(IMP)·6H₂O, Ba(IMP)·6H₂O, Sr(IMP)·6H₂O and Cd(IMP)·4H₂O compounds. The Li(I), Mg(II), Ca(II) and Cd(II) ions bind directly to the phosphate group, and no direct coordination involving the carbonyl C(6)O group was observed in the compounds reported here. Some Raman spectral features in the 750–700 cm⁻¹ range seem to reflect the nucleoside structure of the inosine moiety     

Effects of divalent alkaline earth ions on the magnetic and transport features of La0.65A0.35Mn0.95Fe0.05O3 (A = Ca, Sr, Pb, Ba) compounds

We have studied the magnetic and transport properties of Fe doped La_0.65A_0.35Mn_0.95Fe_0.05O₃ (A = Ca, Sr, Pb, Ba) manganites. All the compositions show ferromagnetic/metal to paramagnetic/insulator transition (T_C) except the Pb doped sample which is insulating and ferromagnetic (FM) in the entire temperature range. The magnetization and T_C are decreased by decreasing the cation size on La site. The transition temperature and magnetic moment at 77 K is a maximum for Sr doped sample and is decreasing if we increase or decrease the cation size from Sr size. The maximum value of T_C and magnetic moment for Sr based sample is most likely due to the closer ionic sizes of La and Sr as compared to the other dopants (Ca, Pb, and Ba). We observed a spin freezing type effect in the Pb doped sample below 120 K in resistivity, ac susceptibility and in magnetization. This suggests that the AFM interactions introduced by the Fe are most effective in the Pb doped composition leading to increased competition between the FM and AFM interactions. This FM and AFM interaction generates some degree of frustration leading to the appearance of spin glass like phase whose typical magnetic behavior is studied for small ion when the metallic like behavior is lost.     

Ionic and electronic conductivities,stability and thermal expansion of La10 − x(Si,Al)6O26 ± δ solid electrolytes

Apatite-type La_10 − xSi_6 − yAl_yO_{27 − 3x/2 − y/2} (x = 0–0.33; y = 0.5–1.5) exhibit predominant oxygen ionic conductivity in a wide range of oxygen partial pressures. The conductivity of silicates containing 26.50–26.75 oxygen atoms per formula unit is comparable to that of gadolinia-doped ceria at 770–870 K. The average thermal expansion coefficients are (8.7–10.8) × 10^− 6 K^− 1 at 373–1273 K. At temperatures above 1100 K, silicon oxide volatilization from the surface layers of apatite ceramics and a moderate degradation of the ionic transport with time are observed under reducing conditions, thus limiting the operation temperature of Si-containing solid electrolytes.     

Low thermal expansion behavior and transport properties of Ni and Ge co-doped manganese nitride materials at cryogenic temperatures

A series of Ni and Ge co-doped manganese nitride materials were fabricated by mechanical ball milling followed by solid-state sintering. Their thermal expansion properties and electrical and thermal conductivities were investigated in the temperature range of 77–300 K. The results show that Ni and Ge co-doped manganese nitride materials have negative thermal expansion (NTE), and the operation-temperature window of NTE shifts toward the lower temperature region and the variation of linear thermal expansion (ΔL/L _(300K)) in the operation-temperature window of NTE decreases with increasing Ni content. The combination of these two factors results in a low coefficient of thermal expansion (CTE) at cryogenic temperatures. The average CTE of Mn₃(Cu_0.2Ni_0.4Ge_0.4)N drops to ‘zero’ in the temperature range of 190–77 K. The values of electrical and thermal conductivities of the Ni and Ge co-doped manganese nitride materials are in the ranges of 2–3×10³ (ohm cm)⁻¹ and 1.6–3.4 W (m K)⁻¹, respectively.     

Ionic conductivity of brownmillerite-type calcium ferrite under oxidizing conditions

The thermogravimetric and Mössbauer spectroscopy studies showed that, at atmospheric oxygen pressure, the oxygen content in Ca₂Fe₂O₅ brownmillerite is very close to stoichiometric at 300–1270 K. The orthorhombic lattice of calcium ferrite undergoes a transition from primitive (space group Pnma) to body-centered (I2mb) at 950–1000 K, which is accompanied with decreasing thermal expansion coefficient (TEC) and increasing activation energy for the total conductivity, predominantly p-type electronic. The steady-state oxygen permeation through dense Ca₂Fe₂O₅ ceramics is limited by the bulk ionic conduction. The ion transference numbers in air vary in the range 0.002–0.007 at 1123–1273 K, increasing with temperature. Analysis of stereological factors, which may affect oxygen diffusivity, suggests a dominant role of the ion jumps along octahedral and, possibly, tetrahedral layers of the brownmillerite structure. The ionic conductivity of calcium ferrite is higher than that of Ca₂FeAlO_5+δ, but lower compared to the oxygen-deficient perovskite phases based on SrFeO_3−δ where the diffusion pathways form a three-dimensional network. The average TECs of Ca₂Fe₂O₅ ceramics, calculated from dilatometric data in air, are 13.1 × 10^− 6 K^− 1 at 370–950 K and 11.3 × 10^− 6 K^− 1 at 970–1270 K.     

Transport properties and structural stability of tetragonal CeNbO4+δ

The electrical properties of CeNbO_4+δ have been investigated at 1073–1223 K in the oxygen partial pressure range 10^− 17 to 0.36 atm. The conductivity and Seebeck coefficient behaviour indicates that, at oxygen chemical potentials close to atmospheric, tetragonal CeNbO_4+δ possesses a mixed ionic and p-type electronic conductivity. The ion transference numbers under the p(O₂) gradient of 0.93/0.21 atm, measured by the modified e.m.f. technique, are close to 0.4 decreasing in more reducing environments. The variations of partial ionic and electronic conductivities can be described in terms of the oxygen intercalation into the scheelite-type lattice, which results in increasing concentrations of both dominant charge carriers, oxygen interstitials and holes, when p(O₂) increases. Reduction leads to p(O₂)-independent electrical properties, followed by a drastic decrease in the conductivity at oxygen pressures below 10^− 15–10^− 9 atm due to a reversible transition into the monoclinic phase. Contrary to the zircon-type CeVO_4±δ, no traces of the parent binary oxides were detected in the reduced cerium niobate.     

Synergistically Enhancing Thermoelectric Performance of n-Type PbTe with Indium Doping and Sulfur Alloying

To achieve high-performance n-type PbTe-based thermoelectric materials, this work provides a synergetic strategy to improve electrical transport property with indium (In) element doping and reduces thermal conductivity with sulfur (S) element alloying. In n-type PbTe, In doping can tune the carrier density in the whole working temperature range, causing the carrier density to increase from 2.18 × 10¹⁹ cm⁻³ at 300 K to 4.84 × 10¹⁹ cm⁻³ at 823 K in Pb_0.98In_0.005Sb_0.015Te. The optimized carrier density can further modulate electrical conductivity and Seebeck coefficient, finally contributing to a substantial increase of power factor, and a maximum power factor increase from 19.7 µW cm⁻¹ K⁻² in Pb_0.985Sb_0.015Te to 28.2 µW cm⁻¹ K⁻² in Pb_0.9775In_0.0075Sb_0.015Te. Based on the optimally In-doped PbTe, S alloying is introduced to suppress phonon propagation by forming a complete solid solution, which could effectively reduce lattice thermal conductivity and simultaneously benefit carrier mobility to maintain high power factor. With S alloying, the minimum lattice thermal conductivity decreases from 0.76 Wm⁻¹ K⁻¹ in Pb_0.985Sb_0.015Te to 0.42 Wm⁻¹ K⁻¹ in Pb_0.98In_0.005Sb_0.015Te_0.88S_0.12. Combining the advantages of both In doping and S alloying, the peak ZT value and averaged ZT (ZT_ave) (300–873 K) are boosted from 1.0 and 0.60 in Pb_0.985Sb_0.015Te to 1.4 and 0.87 in Pb_0.98In_0.005Sb_0.015Te_0.94S_0.06.     

Impedance and dielectric studies of nanocomposite polymer electrolyte systems using MMT and ferroelectric fillers

Impedance and dielectric properties of nanocomposite polymer electrolyte systems modified with nano size MMT and ferroelectric fillers have been investigated for varying lithium to oxygen ratios. The changes in the structural properties of the electrolyte samples were characterized by X-ray diffraction (XRD) and differential scanning calorimetric (DSC) technique. The ion transport number estimated by DC polarization technique is found to be between 0.86 and 0.95. The bulk conductivities of nanocomposite polymer electrolyte films were studied using impedance spectroscopic technique. The impedance plot shows high frequency semicircle, due to the bulk effect of sample and maximum ionic conductivity of 2.15 × 10⁻⁴ Scm⁻¹ was observed for (PEO)₄LiCBSM at 323 K with lithium to oxygen ratio 1: 4. The complex impedance data was used to evaluate ionic conductivity and dielectric relaxation process, to understand the ion transport mechanism in these systems.

     

Synthesis and investigations on the stability of La0.8Sr0.2CuO2.4+δ at high temperatures

For application in solid oxide fuel cells La_0.8Sr_0.2CuO_2.4+δ was synthesized and the phase evolution was characterized after quenching from different temperatures and after slow cooling. A single phase perovskite was found after quenching from 950 °C. The electrical conductivity of the La_0.8Sr_0.2CuO_2.4+δ perovskite exhibited metallic behavior reaching values of about 270 S/cm at 800 °C in air. The thermal expansion between 30 and 800 °C gave a thermal expansion coefficient of 11.1 × 10^− 6 K^− 1.At higher temperatures, the perovskite was transformed to the K₂NiF₄-type structure via an intermediate stage that can be best described as a LaSrCuO₄ phase with preferential growing of {020} lattice planes. After sintering at 1100 °C and slow cooling in the furnace a phase mixture of (La,Sr)CuO_4+δ and (La,Sr)CuO_2.4+δ perovskite was obtained. This phase mixture showed higher electrical conductivity (400 S/cm at 800 °C) and smaller thermal expansion coefficient (9.6 × 10^− 6 K^− 1) than the single phase La_0.8Sr_0.2CuO_2.4+δ perovskite.     

Enhancement of ionic conductivity by dispersed oxide inclusions: Influence of oxide isoelectric point and cation size

Doping of a halide salt by dispersion of oxide particles rather than subtitutional impurities is a proven method of enhancing the extrinsic ionic conductivity of the host. The conductivity mechanism in any space-charge layer at the oxide/host interface is determined by the chemical reactions at the interface. These interactions are discussed by analogy with the particle hydrates. The enhancement of the F⁻-ion conductivity in PbF₂ is predicted to be via F⁻-ion vacancies in the space-charge region and to increase with decreasing oxide isoelectric point and increasing normal anion coordination of the oxide cation. This prediction accounts satisfactorily for the relative enhancement factors measured for PbF₂ containing dispersed CeO₂, SiO₂, ZrO₂ and Al₂O₃.     

Influences of LiCF3SO3 and TiO2 nanofiller on ionic conductivity and mechanical properties of PVA:PVdF blend polymer electrolyte

In recent years, solid polymer electrolytes have been extensively studied due to its flexibility, electrochemical stability, safety, and long life for its applications in various electrochemical devices. Interaction of LiCF₃SO₃ and TiO₂ nanofiller in the optimized composition of PVA:PVdF (80:20—system-A possessing σ ~ 2.8 × 10⁻⁷ Scm⁻¹ at 303 K) blend polymer electrolyte have been analyzed in the present study. LiCF₃SO₃ has been doped in system-A, and the optimized LiCF₃SO₃ doped sample (80:20:15-system-B possessing σ ~ 2.7 × 10⁻³ Scm⁻¹ at 303 K) has been identified. The effect of different concentration of TiO₂ in system-B has been analyzed and the optimized system is considered as system-C (σ ~ 3.7 × 10⁻³ Scm⁻¹ at 303 K). The cost effective, solution casting technique has been used for the preparation of the above polymer electrolytes. Vibrational, structural, mechanical, conductivity, thermal, and electrochemical properties have been studied using FTIR, XRD, stress-strain, AC impedance spectroscopic technique, DSC and TGA, LSV, and CV respectively to find out the optimized system. System-C possessing the highest ionic conductivity, higher tensile strength, low crystallinity, high thermal stability, and high electrochemical stability (greater than 5 V vs Li/Li⁺) is well suitable for lithium ion battery application.

     

Acoustic absorption in superionic PbF2 across transition temperature

In the present paper, we report a theoretical calculation of temperature variation of the ultrasonic absorption coefficient of PbF₂. The absorption can be explained by the TLS model, with parameters which simultaneously reproduce the specific heat, thermal expansion, bulk modulus and ionic conductivity. Our results agree well with recent experimental reports of ultrasonic attenuation in PbF₂.     

Electronic to ionic conductivity of glasses in the Li2S–Sb2S3–P2S5 system

There is great interest in sulfide glasses because of their high lithium ion conductivity. New sulfide glasses in the Li₂S–Sb₂S₃–P₂S₅ system have been synthesized by classical quenching technique. The glass domain relays on the medium-lithium content (up to 50% molar).Electrical conductivities of the samples have been determined by Impedance Spectroscopy. The isothermal conductivity curves exhibit two regions on dependence of lithium content implying that the conductivity mechanisms in these two regions are different. The compositions of low lithium content (below 20% mol.) have presented low electronic conductivities close to 10^− 8 S/cm at room temperature. The compositions of medium lithium content (30–50% mol.) could be mixed ionic–electronic conductors with predominant ionic conductivities with a maximum close to 10^− 6 S/cm for sample with 50% Li₂S at room temperature. Arrhenius exponential behavior is verified between 25 °C and T_g for all glasses. The activation energies, determined from temperature dependence, are 0.55–0.64 eV. A comparative study with glasses belonging to the other chalcogenide systems has been undertaken on base of the weak electrolyte model and the values of decoupling index, R_τ, are reported. The impedance of the 0.5Li₂S–0.3Sb₂S₃–0.2P₂S₅ ionic conductor can be described by an equivalent circuit R(RQ)(RQ).     

Synthesis and electrochemical properties of Li2S–B2S3–Li4SiO4

New Li⁺ ion-conductive glasses Li₂S–B₂S₃–Li₄SiO₄ were synthesized by rapid quenching, and they were transformed into glass ceramics by heat treatment. The heat treatment increased the ionic conductivities of the Li₄SiO₄-doped glasses, and the highest ionic conductivity observed in the system was 1.0 × 10^− 3 S cm^− 1 at room temperature. The glass ceramics were highly stable against electrochemical oxidation with a wide electrochemical window of 10 V.     

Thermal conductivity of single crystals with a fluorite structure: Cadmium fluoride

The thermal conductivity of Ca, Sr, Ba, and Cd difluoride single crystals and the CdF₂ samples doped by 3 mol % NdF₃, 15 mol % HoF₃, and 10 mol % ErF₃ has been studied using the method of steady longitudinal heat flow in the temperature range 50–300 K. The thermal conductivity of the matrices of these compounds decreases in the order CaF₂-SrF₂-BaF₂-CdF₂. The temperature dependences of the phonon mean free path for these crystals have been calculated from experimental data and exhibit different behaviors. It has been assumed that the intense phonon scattering observed in the undoped CdF₂ sample is caused by the specific features of the processes of phonon-phonon scattering. The formation of heterovalent solid solutions of cadmium difluoride and rare-earth trifluorides is accompanied by a drastic decrease in the thermal conductivity and a change in its character from that typical of dielectric single crystals to that typical of glassy materials.     

Preparation,thermal expansion,chemical compatibility,electrical conductivity and polarization of A2−αA′αMO4 (A = Pr,Sm; A′ = Sr; M = Mn,Ni; α = 0.3, 0.6) as a new cathode for SOFC

A_2−αA′_αMO₄ (A = Pr, Sm, A′ = Sr, M = Ni, Mn) with K₂NiF₄-type structure were synthesized by solid reaction. Their chemical stability, electrical conductivity and thermal expansion behavior as well as cathodic polarization were investigated in relation to the cathode of SOFC. The results showed that A_2−αA′_αMO₄ exhibited a low reactivity with yttria stabilized zirconia (YSZ) electrolyte. The thermal expansion coefficient (TEC) values were changed with the ionic radius of A. The specific conductivities of the nickelates were higher than those of manganites. While the nickelates showed a lower cathodic polarization in comparison with manganites.     

Superprotonic solid solutions between CsHSO4 and CsH2PO4

Solid solutions of (CsHSO₄)_1 − x(CsH₂PO₄)_x (x = 0.25-0.75) were synthesized by mechanical milling method over a wide range of compositions. Superprotonic cubic phase was confirmed for all these samples between 293 and 420 K depending on its composition. These superprotonic phases have primitive cubic structure similar to that of CsH₂PO₄. The kinetic stability of the supercooled cubic phase depends both on the composition x and the humidity of surrounding atmosphere. The most stable composition of the cubic phase was found around x = 0.67 and could be maintained for several days even under ambient atmosphere. The ionic conductivities of these superprotonic phases reached 10^− 2–10^− 3 S∙cm^− 1 at 450 K. With increasing x the ionic conductivity at the superprotonic phase decreased continuously associated with the increase of the activation energy. These findings suggest that the average number of the hydrogen bonds between XO₄ (X = S, P) units plays an important role on the stability of the cubic phase and also on the conductivity.     

Mixed conductivity and electrocatalytic performance of SrFeO3-δ–SrAl2O4 composite membranes

Oxygen-ionic and electronic transport in dense (SrFe)_1−x(SrAl₂)_xO_z composites, consisting of strontium-deficient Sr(Fe,Al)O_3-δ and SrAl₂O₄ phases, is determined by the properties of perovskite-like solid solution. Increasing the content of SrAl₂O₄, with a total conductivity as low as 5 × 10^− 7 −  10^− 5 S × cm^− 1 at 973–1273 K in air, results in the gradual decrease of the partial conductivities, but also enables the suppression of thermal expansion. Compared to single-phase SrFe_1−xAl_xO_3-δ, (SrFe)_1−x(SrAl₂)_xO_z composites exhibit enhanced thermomechanical properties, while the oxygen permeability of these materials has similar values. The composite membranes exhibit stable performance under air/(H₂–H₂O–N₂) and air/(CH₄–He) gradients at 973–1173 K. The oxidation of dry methane by oxygen permeating through (SrFe)_0.7(SrAl₂)_0.3O_z results in dominant total oxidation, suggesting the necessity to incorporate a reforming catalyst into the ceramic reactors for natural gas conversion.     

Strongly anisotropic thermal conductivity in planar hexagonal borophene oxide sheet

The flat hexagonal borophene oxide (B₂O) has the highest Li storage capacity among existing two-dimensional materials. Thermal conductivity is an important parameter for the safety of Li-ion batteries. We investigate the lattice thermal conductivity of B₂O by solving phonon Boltzmann transport equation combined with the first-principles calculations. We found that the relaxation time approximation remarkably underestimate the thermal conductivity (κ) of monolayer B₂O, revealing phonon hydrodynamics characteristic. The κ of B₂O from the exact solution of Boltzmann transport equation is 53 W m⁻¹ K⁻¹ and 130 W m⁻¹ K⁻¹ along armchair-direction and zigzag-direction at 300 K, respectively. B₂O exhibits strong thermal transport anisotropy due to anisotropic phonon group velocity, obviously larger than that of other borophene allotropes. At room temperature, the phonon mean free path of B₂O is about 231 nm and 49 nm along armchair-direction and zigzag-direction, respectively. The highly anisotropic thermal conductivity of B₂O offers new possibilities for its applications in thermal management.