The optical properties of CdxZn1−xS thin films on glass substrate prepared by spray pyrolysis method

A series of Cd_xZn_1−xS thin films have been deposited on glass substrates using spray pyrolysis technique. The crystallinity and microstructure of Cd_xZn_1−xS thin films have been investigated by X-ray diffraction (XRD). Based on the results of Hall measurements, the films obtained were an n-type semiconductor. The X-ray data analysis of Cd_xZn_1−xS thin films showed that the grain size of the Cd_xZn_1−xS increased with increase in Cd composition. It is observed that the band gap increases as the Cd composition decreases. The results also showed a blue shift of absorption edge of optical transmission spectra is increases as Zn ratio increases. The effects of Cd composition on the structural and optical properties of Cd_xZn_1−xS thin films were related to their grain size, stress and carrier concentration.     

Investigation on the structural properties and correlation of the optical constants of Cd1-xZnxS thin films with bath deposition temperature

Cd_1-xZn_xS thin films were deposited by chemical bath deposition (CBD) technique, which is simple and cost effective, in a chemical bath containing appropriate amount of cadmium acetate, zinc acetate, and thiourea as precursors, in a clean glass substrate. The deposition was carried out by varying the bath temperatures (70 °C, 75 °C, 80 °C, and 85 °C) of the precursor solution. The XRD results indicate the existence of hexagonal structures of Cd_1-xZn_xS with an average crystallite size of ∼ 27–41 nm. EDX studies confirm the presence of Cd, Zn, and S in the films. HRTEM and SAED patterns show the crystalline nature of the films with the coexistence of the hexagonal phase. The optical constants viz; optical band gap, Urbach energy, static refractive index, and optical conductivity were studied by using UV- Vis transmission spectra as a function of CBD temperature. It was observed that with the increase of bath temperature in the above range, there were concomitant decreases in optical band gap from ∼3.3 to 2.8 eV. The Urbach energy, optical conductivity, and static refractive index of the films increase with the increase in bath deposition temperature. FTIR studies confirm the formation of ternary Cd_1-xZn_xS thin films.     

Structural,electrical and optical properties of Cd1−xZnxO thin films and alloying effects on Kβ/Kα intensity ratios

Cd_1?xZn_xO thin films were prepared by spray pyrolysis in air atmosphere on a glass substrate at 250 °C. The Zn content in Cd_1?xZn_xO films was varied from x = 0 to 0.60. Structural, electrical and optical properties of Cd_1?xZn_xO films were investigated by x‐ray diffraction, electrical resistivity and optical transmittance spectra, respectively. As the Zn content in Cd_1?xZn_xO thin films increased, the preferred orientation of the films did not change, only the peak intensity of the planes decreased. In addition to the peaks of CdO, peaks of ZnO were observed in the film with x = 0.6. The resistivity of Cd_1?xZn_xO thin films increased with increasing Zn content. Transmittance spectra studies of films were carried out in the 190‐1100 nm wavelength range and the results showed that the bandgap energy range varied from 2.42 to 3.25 eV. In addition, alloying effect on the Kβ/Kα intensity ratio in Cd_1?xZn_xO semiconductor thin films was studied. It was found that the Kβ/Kα intensity ratio is changed by alloying effects in Cd_1?xZn_xO semiconductor thin films for different composition of x. The results were compared with the theoretical values. Copyright © 2006 John Wiley & Sons, Ltd.     

Growth, structural and optical properties of CdxZn1−xS thin films deposited using spray pyrolysis technique

Cd_xZn_(1−x)S (x = 0, 0.2, 0.4, 0.6, 0.8, and 1) thin films were deposited by the chemical spray pyrolysis technique using a less used combination of chemicals. Depositions were done at 573 K on cleaned glass substrates. The composition, surface morphology and structural properties of deposited films were studied using EDAX, SEM and X-ray diffraction technique. XRD studies reveal that all the films are crystalline with hexagonal (wurtzite) structure and inclusion of Cd into the structure of ZnS improved the crystallinity of the films. The value of lattice constant ‘a’ and ‘c’ have been observed to vary with composition from 0.382 to 0.415 nm and 0.625 to 0.675 nm, respectively. The band gap of the thin films varied from 3.32 to 2.41 eV as composition varied from x = 0.0–1.0. It was observed that presence of small amount of cadmium results in marked changes in the optical band gap of ZnS.     

Effect of NaF on optical and structural properties of CdxZn1−xS nano crystalline films

This work investigates the effect of NaF on optical and structural properties of nano crystalline Cd_xZn_1?xS films. The Cd_xZn_1?xS films are prepared through chemical bath deposition (CBD) technique in aqueous alkaline bath and their subsequent condensation on substrates. The as-obtained samples are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and UV–VIS absorption spectroscopy. Micro structural features, obtained from XRD analysis confirm the formation of cubic phase of undoped as well as NaF doped Cd_xZn_1?xS nano particles while SEM observations depict non-uniform distribution of grains. These results show the average grain size of pure as well as NaF doped samples to range from 50 to 90 nm. Tauc's plots, extracted from absorption spectra exhibit absorption to be dominating mainly in blue-green region of visible spectrum. The room-temperature photoluminescence (PL) spectra of Cd_xZn_1?xS samples show a peak around 425 nm, which gets blue shifted for doped sample indicating improvement in PL properties on its addition.     

Photoluminescence measurements in the phase transition region of Zn<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>Cd<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>S films

Thin films of Zn_1−x Cd _x S (0.1 ≤ x ≤ 0.5) were prepared by using pulsed laser ablation technique on corning glass substrates. Phase transition from cubic to hexagonal in Zn_1−x Cd _x S films is determined by X-ray diffraction analysis. We observed a lowering in the phase transition temperature with increase in the cadmium concentration. Transmission electron microscopy suggests the crystalline nature of thin films with average particle size of 15 nm. The grown Zn_1−x Cd _x S samples show the high peak intensity ratio of the near band edge emission to the defect center luminescence even at room temperature, which indicates the small concentration of complex defects in the samples. Photoluminescence measurement show stoichiometric dependence of the energy band gap and is found to have quadratic dependence on x.     

Effect of indium incorporation on the optical properties of spray pyrolyzed Cd0.22Zn0.78S thin films

In this study, effect of indium incorporation on the optical properties is investigated for the spray pyrolyzed onto glass substrates at 275°C substrate temperature undoped and indium doped Cd_0.22Zn_0.78S thin films. The average optical transmittance of all the films was over 77% in the wavelength range between 450 and 800 nm. The optical band gap energies of the thin films have been investigated by the measurement of the optical absorbance as a function of wavelength. The optical absorption studies reveal that the transitions are direct band gaps of 3.02 and 3.05 eV for undoped and doped indium Cd_0.22Zn_0.78S thin films, respectively. The Urbach tail parameter and optical constants such as refractive index, extinction coefficient, and dielectric constants were calculated for these films. The dispersion parameters such as single-oscillator energy and dispersive energy were discussed in terms oft he single-oscillator Wemple—DiDomenico model.     

Structure, refractive-index dispersion and the optical absorption edge of chemically deposited ZnxCd(1-x)S thin films

Zinc cadmium sulfide, Zn_xCd_(1-x)S, thin films have been deposited by a simple and inexpensive chemical bath deposition method from an aqueous medium using thiourea as a sulfide-ion source. The structure of the deposited films has been characterized by X-ray diffraction and transmission electron microscopy. It was observed from X-ray diffraction that the as-deposited films were amorphous in nature. However Zn_xCd_(1-x)S films annealed at 423 K for 1.5 h show a crystalline structure with a small scattering volume. The obtained results were confirmed throughout the transmission electron microscopy and the corresponding electron-diffraction patterns. The optical constants of Zn_xCd_(1-x)S films annealed at 423 K for 1.5 h in the compositional range 0≤x≤1 were estimated using transmission and reflection spectra in the wavelength range 300–2500 nm. The band gap varies non-linearly with the value of x. The dependence of the refractive index on the wavelength obeys the single-oscillation model, from which the dispersion parameters and the high-frequency dielectric constant were determined. A graphical representation of the surface and volume energy-loss functions was also given. Received: 23 February 2001 / Accepted: 26 February 2001 / Published online: 27 June 2001     

Effect of Mg doping and substrate temperature on the properties of pulsed laser deposited epitaxial Zn1?xMgxO thin films

In this paper, we report on the pulsed laser deposition of epitaxial (0002) oriented Zn_1−x Mg _x O thin films onto (0001) sapphire substrate in O₂ ambient at different deposition temperatures. Pulsed laser deposited Zn_1−x Mg _x O films showed (0002) oriented hexagonal wurtzite structure up to 34% of Mg concentration. The bandgap of Zn_1−x Mg _x O thin films is successfully tuned from 3.3 to 4.2 eV by adjusting the Mg concentration x=0.0 to x=0.34. Pulsed laser deposited Zn_1−x Mg _x O thin films were characterized by XRD, AFM, SEM, PL and UV–VIS spectrometer. We have also studied the effect of deposition temperature on to the structure, surface morphology and optical properties of Zn_1−x Mg _x O thin films.     

Oxygen flux influence on the morphological, structural and optical properties of Zn1−xMgxO thin films grown by plasma-assisted molecular beam epitaxy

The Zn_1−xMg_xO thin films were grown on Al₂O₃ substrate with various O₂ flow rates by plasma-assisted molecular beam epitaxy (P-MBE). The growth conditions were optimized by the characterizations of morphology, structural and optical properties. The Mg content of the Zn_1−xMg_xO thin film increases monotonously with decreasing the oxygen flux. X-ray diffractometer (XRD) measurements show that all the thin films are preferred (0 0 2) orientated. By transmittance and absorption measurements, it was found that the band gap of the film decreases gradually with increasing oxygen flow rate. The surface morphology dependent on the oxygen flow rate was also studied by field emission scanning electron microscopy (FE-SEM). The surface roughness became significant with increasing oxygen flow rate, and the nanostructures were formed at the larger flow rate. The relationship between the morphology and the oxygen flow rate of Zn_1−xMg_xO films was discussed.     

The effect of copper concentration on structural,optical and dielectric properties of CuxZn1 − xS thin films

Cu_xZn_1 ? xS (x = 0, 0.25, 0.50, 0.75, 1) thin films were deposited on glass substrates using Successive Ionic Layer Adsorption and Reaction (SILAR) method at room temperature and ambient pressure. The copper concentration (x) effect on the structural, morphological and optical properties of Cu_xZn_1 ? xS thin films was investigated. The X-ray diffraction (XRD) and scanning electron microscopy (SEM) studies showed that all the films exhibit polycrystalline nature and are covered well with glass substrates. The crystalline and surface properties of the films improved with increasing copper concentration. The energy bandgap values were changed from 2.07 to 3.67 eV depending on the copper concentration. The refractive index (n), optical static and high frequency dielectric constants (ε_o, ε_∞) values were calculated by using the energy bandgap values as a function of the copper concentration.     

Effect of laser incident energy on the structural,morphological and optical properties of Cu2ZnSnS4 (CZTS) thin films

The polycrystalline Cu₂ZnSnS₄ (CZTS) thin films have been prepared by pulsed laser deposition (PLD) method at room temperature. The laser incident energy was varied from 1.0 at the interval of 0.5–3.0 J/cm². The effect of laser incident energy on the structural, morphological and optical properties of CZTS thin films was studied by means of X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and optical absorption. The studies reveal that an improvement in the structural, morphological and optical properties of CZTS thin films with increasing laser incident energy up to 2.5 J/cm². However, when the laser incident energy was further increased to 3.0 J/cm², leads to degrade the structural, morphological and optical properties of the CZTS thin films.     

Optical properties of Cd1−xZnxTe thin films fabricated through sputtering of compound semiconductors

Cd_1−xZn_xTe thin film fabrication is necessary for its photovoltaic and imaging applications in large scale. Thermally annealed and thereby interdiffused r.f. sputtered multilayers comprising of CdTe and ZnTe have been utilized here for the fabrication of Cd_1−xZn_xTe thin films. Photoluminescence and change of resistance of the multilayer under illumination were studied using different annealing temperatures and varying number of repetitions. It was found that three number of repetitions annealed at 300 °C exhibited the best results.     

Electronic and optical properties of CdS/CdZnS nanocrystals

Cd1-x ZnxS nanocrystals are prepared by a co-precipitation method with different atomic fractions of Zn.The texture,structural transformation and optical properties with increasing x value in Cd1-x ZnxS are studied with scanning electron microscopy,electron diffraction patterning,and absorption spectra respectively.Quantum confinement in a strained CdS/Cd1-xZnxS related nanodot with various Zn content values is investigated theoretically.Binding energies on exciton bound CdS/CdxZn1-xS quantum dot are computed,with consideration of the internal electric field induced by the spontaneous and piezoelectric polarizations,and thereby the interband emission energy is calculated as a function of the dot radius.The optical band gap from the UV absorption spectrum is compared with the interband emission energy computed theoretically.Our results show that the average diameter of composite nanoparticles ranges from 3 nm to 6 nm.The X-ray diffraction pattern shows that all the peaks shift towards the higher diffracting angles with an increase in Zn content.The lattice constant gradually decreases as the Zn content increases.The strong absorption edge shifts towards the lower wavelength region and hence the band gap of the films increases as the Zn content increases.The values of the absorption edge are found to shift towards the shorter wave length region and hence the direct band gap energy varies from 2.5 eV for the CdS film and 3.5 eV for the ZnS film.Our numerical results are in good agreement with the experimental results.     

Annealing effect on the structural and optical properties of a Cd1−xZnxS thin film for photovoltaic applications

Herein is a report of a study on a Cd_1−xZn_xS thin film grown on an ITO substrate using a chemical bath deposition technique. The as-deposited films were annealed in air at 400 °C for 30 min. The composition, surface morphology and structural properties of the as-deposited and annealed Cd_1−xZn_xS thin films were studied using EDX, SEM and X-ray diffraction techniques. The annealed films have been observed to possess a crystalline nature with a hexagonal structure. The optical absorption spectra were recorded within the range of 350-800 nm. The band gap of the as-deposited thin films varied from 2.46 to 2.62 eV, whereas in the annealed film these varied from 2.42 to 2.59 eV. The decreased band gap of the films after annealing was due to the improved crystalline nature of the material.     

Structural, optical and electrical properties of cadmium zinc oxide films for light emitting devices

Structural, optical and electrical properties of Cd_yZn_1-yO (y=0–0.1) ternary alloy thin films have been investigated for the films prepared using the spin coating method on the glass substrate. XRD pattern confirmed the nano-size polycrystalline hexagonal wurtzite structure for all the samples. The size of nano-crystals was found to be varied in between 21 and 30 nm. Optical band gap calculated from the absorption coefficient signifies the shift in direct band gap from 3.2 to 2.97 eV with cadmium composition. Through EDAX spectrum, it was confirmed that Cadmium was successfully incorporated into ZnO. SEM studies make clear that even after Cadmium incorporation, the surface morphology of the films remained smooth. The current–voltage characteristics obtained from semiconductor characterization system reveals that resistance of the films was found to be decreased with the increase in cadmium composition. Our investigations lead to the applicability of CdZnO as an active layer in CdZnO/ZnO heterostructure for light emitting devices.     

Structure and optical properties of Cd-substituted ZnO (Zn1−x Cd x O) thin films synthesized by the dc reactive magnetron sputtering

The ternary Zn_1?x Cd _x O (x = 0, 0.2) thin films with wurtzite structure and highly (002)-preferred orientations were deposited on glass substrates by the direct current (dc) reactive magnetron sputtering method. The X-ray diffraction, X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), optical absorption spectra and photoluminescence (PL) were employed to investigate the structural and the optical properties in detail. The results indicated that as x varied from x = 0–0.2, the diffraction angle of the (002) peaks decreased from ~34.36° to ~33.38° and the lattice spacing increased from 0.260 to 0.268 nm. Moreover, the optical band-gap of the Zn_1?x Cd _x O thin films with the wurtzite structure decreased from 3.20 eV at x = 0–2.70 eV at x = 0.2. Correspondingly, the near-band-edge PL was tuned in a wide visible region from ~393 to 467 nm. The chemical bonding states of Cd in Zn_1?x Cd _x O alloy thin films were examined by XPS analysis.     

Microstructure,optical and structural characterization of Cd0.98Fe0.02S thin films co-doped with Zn by chemical bath deposition method

Fe-doped CdS (Cd_0.98Fe_0.02S) and Fe, Zn co-doped CdS (Cd_0.98−xZn_xFe_0.02S (x=0.02, 0.04, and 0.06)) thin films have been successfully deposited on glass substrate by chemical bath deposition technique using aqueous ammonia solution at pH = 9.5. Phase purity of the samples having cubic structure with (111) as the preferential orientation was confirmed by X-ray diffraction technique. Shift of X-ray diffraction peak position towards higher angle side and decrease of lattice parameters, volume and crystallite size confirmed the proper incorporation of Zn into Cd–Fe–S except Zn=6%. The compositional analysis (EDX) showed that Cd, Fe, Zn and S are present in the films. The enhanced band gap and higher transmittance observed in Cd_0.94Zn_0.04Fe_0.02S films are the effective way to use solar energy and enhance its photocatalytic activity under visible light. The enhanced green band emission than blue band by Zn-doping evidenced the existence of higher defect states.     

Structural,electrical and optical properties of boron doped ZnO thin films using LSMCD method at room temperature

Zn_1−x B _x O (0≤x≤0.04) thin films were deposited by the liquid source misted chemical vapor deposition (LSMCD) method. The thin films were polycrystalline with grain sizes of 16 nm to 22 nm. The structural, optical, and electrical properties were investigated by X-ray diffraction, UV-visible spectrophotometry, Raman spectroscopy, and Hall effect measurement. Also scanning electron (SEM) and atomic force microscopy (AFM) techniques were used in order to determine the morphological and topological characteristics of the films. The optimal result of Zn_1−x B _x O films was obtained at x=0.02, with a low resistivity of ≈10⁻² Ω cm, and a high transmittancy of 85% in the visible light spectrum (300 nm ∼ 800 nm).     

Effect of cycle numbers on the structural,linear and nonlinear optical properties in Fe2O3 thin films deposited by SILAR method

Fe₂O₃ thin films were deposited by Successive Ionic Layer Adsorption and Reaction (SILAR) method onto glass substrates at different cycle numbers to investigate structural, linear and nonlinear optical properties. X-Ray Diffraction (XRD) analysis revealed that the Fe₂O₃ thin films have a non-crystalline nature. The morphological properties of the films were investigated by Field Emission-Scanning Electron Microscopy (FE-SEM) and the results show that the films’ surfaces are porous. The linear and nonlinear optical parameters were evaluated and analyzed by using transmittance and absorbance measurements. For these measurements, UV–Vis spectroscopy at room temperature was used. The refractive index values were calculated in the range of 1.45–3.23 for visible region (400–700 nm). Obtained results reveal that direct optical band gap changed between 2.62 and 2.68 eV and indirect optical band gap changed between 1.67 and 1.77 eV. Additionally, optical electronegativity, optical dielectric constants, surface and volume energy loss functions, nonlinear refractive index, linear optical susceptibility, third-order nonlinear optical susceptibility, optical and electrical conductivity, and loss tangent values were calculated and discussed in detail. It was found that each parameter studied is dependent on the cycle numbers. Also, it can be stated that Fe₂O₃ thin films are promising candidate for solar cells and optoelectronic device technology.