Quasi-stadium laser diodes with an unstable resonator condition

We have observed lasing in a complicated eigenmode of a quasi-stadium laser diode with an unstable resonator consisting of two curved end mirrors obeying an unstable resonator condition and two straight sidewall mirrors. The laser was fabricated by application of a reactive-ion-etching technique to a molecular beam epitaxy-grown graded-index separate-confinement heterostructure single-quantum-well GaAs/AlGaAs structure. The far-field pattern shows that the lasing mode corresponds to the complicated lowest-loss mode obtained numerically by an extended Fox-Li method.     

管板式大功率横流CO2激光横模测量及数值模拟

为了提高激光稳定性和激光加工质量,实验测量了大功率横流CO2激光横模,并理论分析了横模形成机理。针对大功率横流CO2激光器管板式电极结构,由麦克斯韦方程给出电场的横向分布,并通过数值计算得到了激光强度的横向分布。实验结果与数值模拟得到的激光能量分布基本一致。结果表明,在给定放电电压条件下,电极结构和气体流动速率决定了激光横模峰值大小,激光峰值的横向位置取决于气体流动的速率。     

Continuous-wave Yb-doped Sc2SiO5 thin-disk laser

We present in this Letter experimental results of a Yb:Sc(2)SiO(5) (Yb:SSO) thin-disk laser. To our knowledge, this is the first lasing demonstration of this crystal in thin-disk configuration reported on to date. Preliminary tests regarding the characterization and the laser operation are presented. Two different resonator configurations, a simple linear multimode cavity, and a fundamental-mode folded resonator providing a double pass in the laser crystal were set up. The gain and the small signal gain of the available Yb:SSO sample were calculated using the experimental results of the multimode resonator. The operation in a fundamental-mode resonator with the double pass in the laser crystal led to 9.4 W of output power with an optical efficiency of 25.4%.     

Self-modulation lasing regimes in a fast-flow CO<Subscript>2</Subscript> laser

Numerical simulation of self-modulation lasing regimes has been carried out for a CO₂ laser with transverse flow of the active medium through an unstable resonator with inhomogeneous internal pumping. Two types of steady-state self-modulation oscillation differing in the feedback mechanism were observed. The type of lasing regime and the conditions of its realization depend both upon the pumping profile and upon the composition and pressure of the working mixture, which makes it generally possible to control temporal characteristics of lasing.     

三环无源谐振腔在光纤激光器中的选频特性

利用琼斯矩阵对一种三环嵌套的无源谐振腔的选频特性进行了分析,并根据无源谐振腔选频的原理,设计了一种基于三环嵌套无源谐振腔的掺铒光纤激光器.实验结果表明:三环嵌套的无源谐振腔具有良好的选频特性,当泵浦功率为159 mW时,得到了稳定的单纵模激光信号输出;输出功率的最大波动为0.04 dB,输出中心波长最大漂移为0.016...     

Lasing emission of dye-doped cholesteric liquid crystal microdroplet wrapped by polyglycerol in hollow glass microsphere

In this Letter,a dye-doped cholesteric liquid crystal(DDCLC)-filled hollow glass microsphere is demonstrated to be a resonator with good temperature response.A diglycerol layer is used to wrap the DDCLCs microdroplet to keep it steady and control its orientation.The whispering gallery mode(WGM)lasing and photonic band gap(PBG)lasing caused by two different mechanisms were obtained under the pump of a pulsed laser,and the temperature response of these two kinds of lasing was studied.For the liquid crystal and chiral material used in this Letter,both the WGM lasing and the PBG lasing have a blue shift in wavelength with increasing temperature.     

An interferometrically tuned and actively modelocked cw dye laser

An interferometer of the Michelson type is used to tune and to actively modelock an argon ion laser pumped cw dye laser. The interferometer constitutes a resonator mirror with a modulated reflecting coefficient. This modulation corresponds to a transient Fourier spectrum containing the whole emission band of the dye. In the center of this spectrum, a mode-locked train of picosecond pulses is generated. These pulses are tunable throughout the tuning range of the employed lasing medium in a simple and convenient way. Due to the inherent characteristic broad band output of the cw dye laser, the modulation envelope extends only for a fraction of the entire lasing period. Means of extending the said envelope to cover the complete laser output are discussed.     

碟型量子阱微腔激光器的低阈值激射

利用反应离子刻蚀(RIE)和湿法腐蚀方法在InGaAs/InGaAsP多量子阱材料上研制出直径为8μm、4.5μm和2μm的碟型半导体微腔激光器。其中2μm直径的微碟在液氮温度下其光泵浦激射阈值仅为3μW左右。对高光功率密度下泵浦时出现的多模激射、跳模和激射光谱强度饱和现象进行了研究。并对微碟激光器的激射光谱线宽特性进行了初步的分析。     

Effect of chromatic aberration on Gaussian beams: non-dispersive laser resonators

The propagation of a non-monochromatic (polychromatic) TEM₀₀ Gaussian beam in vacuum, its passage through a thin plate and its transformation by a thin lens are studied in the case of a non-dispersive laser resonator. The basic assumptions of the model are as follows: optical fields are stationary and plane-polarized, the paraxial wave equation is valid, an equivalent non-dispersive hemiconfocal resonator represents the lasing medium and its stable resonator, the laser emits in a single mode. It is also assumed that the plate and the lens have large transverse dimensions. Mathematical expressions, for beam radius, divergence, radius of curvature and beam parameter product, are obtained. A beam quality factor for polychromatic Gaussian beams is defined and its value calculated in each case of interest. It is proposed to simulate a dispersive laser resonator by a non-dispersive resonator complemented with a plate and/or a thin lens.     

优化封离型CO2激光工作气体的动力学机理研究

详细讨论了封离型CO₂激光器中CO₂，N₂和He三混合气 体含量被优化组合后的激光动力 学机理. 气体优化可以提高激光输出功率的主要机理是通过适当增加N₂含量， 使N₂激发 态与CO₂激光上能级的碰撞频率增加，提高了激光能级粒子数密度和相对布居数 . 同时， 适当减少CO₂含量，使总的电子动量输运碰撞频率减小、放电电流增大，导致增 加激光上转动能级的弛豫 关键词： 2激光')" href="#">CO₂激光 气体动力学 强化机理     

基于猫眼腔镜损耗调节的激光横模演示系统

提出一种基于猫眼腔镜损耗调节的新型激光横模演示系统。采用半外腔He-Ne激光器,利用由分立的可进行五维微调的凸透镜和凹面镜组成的猫眼逆向器构成损耗可调激光谐振腔,通过调节猫眼逆向器改变激光谐振腔的损耗比，实现改变激光横模状态的作用。利用CCD进行图像采集，计算机实现图像存储，从而得到20多种结构清晰的高阶横模花样图片。     

Multiwavelength fiber laser based on a photonic crystal fiber loop mirror with cooperative Rayleigh scattering

In this work, a multiwavelength fiber Raman laser based on a highly birefringent photonic crystal fiber loop mirror is presented. A laser resonator is formed when the Raman amplification with cooperative Rayleigh scattering in a dispersion-compensating fiber is used as a distributed mirror and combined with a photonic crystal fiber loop mirror filtering structure. Stable multiwavelength lasing at room temperature is achieved due to the low temperature sensitivity of the highly birefringent photonic crystal fiber.     

Pulsed first-overtone CO laser: effective source of IR radiation in spectral range of 2.5–4.0 μm

Spectral properties of radiation of a pulsed electron-beam controlled discharge laser operating on the first-overtone transitions (Δv=2) of CO molecules have been studied both experimentally and theoretically. Various sets of dielectric mirrors with high reflectivity in the wide range of overtone spectrum have been used for the laser resonator. Multiwavelength lasing has been obtained in the wide spectral range of 2.5–4.0 μm. Efficiency of the laser operating on few vibrational transitions within a relatively narrow spectral range comes up to 5% at entirely suppressed fundamental band (Δv=1) lasing. Spectral characteristics of the overtone laser operating on a selected set of vibrational transitions have been analyzed theoretically. A comparison of the experimental and theoretical data has been made.     

Efficient high-power UV laser generated by an optimized flat–flat actively Q-switched laser with extra-cavity harmonic generations

We investigate the parasitic lasing effect in the high-power actively Q-switched laser with a flat–flat resonator. The parasitic lasing effect in the low-Q stage is found to lead to long tails in the output pulses, corresponding to the peak-power reduction. We experimentally determine the shortest cavity length without the parasitic lasing effect to optimize the performance of the high-power actively Q-switched laser with a flat–flat cavity. We further use the optimized fundamental laser to generate green and UV lasers by extra-cavity harmonic generations. At a pump power of 44 W, the output powers at 355 nm and 532 nm as high as 6.65 W and 8.38 W are obtained at a pulse repetition rate of 40 kHz.     

Laser performance studies of para-(phenylene-ethynylene) polymers in organic solvents

The lasing performance of the polymers poly(2,5-dioctadecyloxy-paraphenylene-ethynylene-co-2,5-thienyl) (OPT) and poly(2,5-dioctadecyloxy-paraphenylene-ethynylene-co-2,5-pyridinyl) (OPP) in organic solvents was studied. A two-mirror resonator was transversally pumped using single pulses of the second harmonic of a mode-locked ruby laser. OPT in tetrahydrofuran lased in the region from 480 nm to 525nm and OPP in tetrahydrofuran showed laser action in the region from 460 nm to 490nm. The polymer solutions are characterized by absorption and fluorescence spectroscopic analysis. Effective stimulated emission cross-sections are reported. High excited-state absorption cross-sections and residual ground-state absorption reduce the lasing efficiency. This revised version was published online in November 2006 with corrections to the Cover Date.     

基于钠硼铝硅酸盐玻璃的PbSe量子点红外单模光纤激光

根据实验制备的钠硼铝硅酸盐PbSe量子点玻璃及其透射电子显微镜(TEM)图、吸收谱和发射谱,计算机数值模拟了以PbSe量子点作为激活增益介质的红外单模光纤激光。应用遗传算法,通过数值求解粒子数速率方程和激光谐振腔振荡方程,优化计算了量子点光纤激光器(QDFL)的最佳抽运波长、光纤长度、掺杂浓度及出射镜反射率。结果表明:饱和抽运功率为2 W,在1676nm激光波长处,QDFL最大输出功率可达1.36 W,抽运效率达68%。与通常的掺稀土离子(Yb3+、Er3+)的光纤激光器相比,QDFL具有抽运效率高、激励阈值低、掺杂密度可调、光纤饱和长度短等特点。由于量子点辐射波长的尺寸依赖特性,容易形成多波长激射或波长可调的新型激光器。     

Array of a dye-doped polymer-based microlaser with multiwavelength emission

This Letter reports a convenient method of fabricating a polymer-based microlaser array. Laterally aligned plastic micropillars equipped with an optical resonator were fabricated by using a lithographic technique with an organic-dye-doped photopolymer, which operated as a laser element with a vertical cavity. Under optical pumping, very fine emission spectra showing a Fabry-Perot-type lasing oscillation were observed. Using this technique, integrated laser cavities with desired operation wavebands can be produced easily.     

Extraction efficiency and thermal lensing in Tm: YAG lasers

We model and compare with experiment the threshold, extraction efficiency and temperature effects in Tm:YAG lasers. In particular, we are concerned with high pump powers where lasing can cease abruptly. We simulate the pump depletion equation with the forward and reverse lasing equations combined with the CW rate equations which include cross-relaxation. The resonator is single-pass, end-pumped Fabry-Perot. Consequently, the equations must be solved numerically with a shooter. Our simulation of these equations gives the z-dependence of the intensities, of the populations and of the heat source. Heating is created by nonradiative decay from the two upper manifolds and by the cross-relaxation energy deficit. This leads to thermal lensing as a function of incident pump power which causes lasing shut-off as the resonator becomes unstable. Our simulations for the slope efficiency, threshold and laser shut-off agree with experiment. Additionally, we show that for pump powers in the range of 15–20 W the core temperature rise is about 40 K and the thermal focal length is in the range 5–6 cm.     

Filtering of light fluctuations by multiple second harmonic generation

It is shown that the level of both quantum and classical light fluctuations can be considerably decreased by multiple second harmonic generation in thin nonlinear plates, when filtering out the generated second harmonic radiation behind each plate. As for the application, a second harmonic plate is proposed to be placed in the laser resonator in order to improve statistical and coherence properties of the lasing mode.     

Yb-Bi pulsed fiber lasers

A new type of pulsed fiber laser is suggested and developed - Yb-Bi lasers. In such lasers the Yb fiber laser is Q-switched by use of a saturable absorber, a Bi-doped fiber placed in its own resonator, and pulsed lasing is obtained in both fiber lasers. Continous-wave diode-clad pumping of the Yb-Bi lasers at a 975 nm wavelength with power up to 16.5 W results in pulsed laser action in a spectral diapason of 1050-1200 nm with a maximum pulse energy of up to 100 microJ, an average power up to 7.5 W, and a repetition rate up to 100 kHz.