Phenothiazine-phenylquinoline donor-acceptor molecules: effects of structural isomerism on charge transfer photophysics and electroluminescence

Large differences in the intramolecular charge-transfer fluorescence quantum yields and electroluminescence efficiencies were observed among the isomeric donor-acceptor molecules 2-(4-phenyl-2-quinolyl)-10-methylphenothiazine (2PQMPT) and 3-(4-phenyl-2-quinolyl)-10-methylphenothiazine (3PQMPT). In solution, the 2PQMPT isomer had a larger positive solvatochromism and thus a greater degree of charge transfer, whereas 3PQMPT had a larger fluorescence quantum yield (71%) compared to 2PQMPT (46%). High brightness (23750 cd/m(2)) and high efficiency (8.18 cd/A, 4.45 lm/W, 2.42% external quantum efficiency at 1015 cd/m(2)) green electroluminescence was achieved from 3PQMPT diodes. In contrast, green light-emitting diodes with lower brightness (8900 cd/m(2)) and efficiencies (4.79 cd/A, 2.36 lm/W, 1.41% external quantum efficiency at 690 cd/m(2)) were obtained from 2PQMPT. The two isomeric donor-acceptor molecules had identical HOMO (5.1 eV) and LUMO (2.4 eV) energy levels derived from electrochemistry. Density functional theory (DFT) calculations provided insights into the molecular geometry, electronic structures, and properties of the donor-acceptor isomers. These results demonstrate the pronounced influence of the donor/acceptor connection on the charge-transfer emission efficiency of donor-acceptor molecules and the performance of solid-state light-emitting devices based on them.     

Synthesis,Photophysics, and Electroluminescence of Poly(dibenzofluorene)s

Summary: A series of soluble poly(dibenzofluorene) derivatives that contain dibenzo[a,g]fluorene, dibenzo[a,i]fluorene, and dibenzo[c,g]fluorene repeat units in the main chain have been synthesized, characterized, and explored as emissive materials in polymer light emitting diodes (PLEDs). These polymers possess higher glass transition temperatures (108–133 °C) than that of poly(2,7‐(9,9‐dialkyl)fluorene) (PFO). The photophysical and electrochemical properties of these polymers are affected by the steric hindrance effect. These polymers emit blue light in dilute solution (378–400 nm) and in the solid state (426–447 nm). As emissive materials in PLEDs, blue electroluminescence with a brightness of up to 3 130 cd · m⁻² is obtained from single‐layer diodes of P₂ with aluminum/barium in air.

The photophysical and electrochemical properties of these polymers are affected by the size effect.     

High-Performance Perovskite Light-Emitting Diode with Enhanced Operational Stability Using Lithium Halide Passivation

Defect passivation has been demonstrated to be effective in improving the radiative recombination of charge carriers in perovskites, and consequently, the device performance of the resultant perovskite light-emitting diodes (LEDs). State-of-the-art useful passivation agents in perovskite LEDs are mostly organic chelating molecules that, however, simultaneously sacrifice the charge-transport properties and thermal stability of the resultant perovskite emissive layers, thereby deteriorating performance, and especially the operational stability of the devices. We demonstrate that lithium halides can efficiently passivate the defects generated by halide vacancies and reduce trap state density, thereby suppressing ion migration in perovskite films. Efficient green perovskite LEDs based on all-inorganic CsPbBr₃ perovskite with a peak external quantum efficiency of 16.2 %, as well as a high maximum brightness of 50 270 cd m⁻², are achieved. Moreover, the device shows decent stability even under a brightness of 10⁴ cd m⁻². We highlight the universal applicability of defect passivation using lithium halides, which enabled us to improve the efficiency of blue and red perovskite LEDs.     

Triphenylamine-Derived Solid-State Emissive Carbon Dots for Multicolor High-Efficiency Electroluminescent Light-Emitting Diodes

Two kinds of triphenylamine-derived solid-state emissive carbon dots (CDs) with orange and yellow color are facilely synthesized through solvothermal treatment, taking advantage of the nonplanar structure and good carrier mobility of triphenylamine unit. Theoretical calculations show that the triphenylamine structure could greatly inhibit the direct π–π stacking of aromatic skeletons and enhance the fluorescence properties of CDs in aggregation state. By adopting the CDs as single emissive layer, high-performance orange-color and green-color electroluminescent light-emitting diodes (LEDs) are successfully fabricated, with maximum brightness of 9450/4236 cd m⁻², high current efficiency of 1.57/2.34 cd A⁻¹ and low turn-on voltage of 3.1/3.6 eV are respectively achieved. Significantly, white-color LED device is further prepared. This work provides a universal platform for the construction of novel solid-state emissive CDs with significant applications in photoelectric device.     

Novel multifunctional organic semiconductor materials based on 4,8-substituted 1,5-naphthyridine: synthesis, single crystal structures, opto-electrical properties and quantum chemistry calculation

A series of 4,8-substituted 1,5-naphthyridines (1a-1h) have been successfully synthesised by a Suzuki cross-coupling between 4,8-dibromo-1,5-naphthyridine (4) and the corresponding boronic acids (2a-2h) in the presence of catalytic palladium acetate in yields of 41.4-75.8% and have ben well characterized. They are thermally robust with high phase transition temperatures (above 186 °C). Compounds 1b, 1e and 1f crystallized in the monoclinic crystal system with the space groups P2(1)/c, P2(1)/c and P2(1)/n, respectively. All of them show the lowest energy absorption bands (λ(max)(Abs): 294-320 nm), revealing low optical band gaps (2.77-3.79 eV). These materials emit blue fluorescence with λ(max)(Em) ranging from 434-521 nm in dilute solution in dichloromethane and 400-501 nm in the solid state. 4,8-Substituted 1,5-naphthyridines 1a-1h have estimated electron affinities (EA) of (2.38-2.72 eV) suitable for electron-transport materials and ionization potentials (IP) of 4.85-5.04 eV facilitate excellent hole-injecting/hole-transport materials properties. Quantum chemical calculations using DFT B3LYP/6-31G* showed nearly identical the lowest unoccupied molecular orbitals (LUMO) of -2.39 to -2.19 eV and the highest occupied molecular orbitals (HOMO) of -5.33 to -6.84 eV. These results demonstrate the 4,8-substituted 1,5-naphthyridines 1a-1h with a simple architecture might be promising blue-emitting (or blue-green-emitting) materials, electron-transport materials and hole-injecting/hole-transport materials for applications for developing high-efficiency OLEDs.     

Water-Driven Synthesis of Deep-Blue Perovskite Colloidal Quantum Wells for Electroluminescent Devices

Perovskite colloidal quantum wells (QWs) are promising to realize narrow deep-blue emission, but the poor optical performance and stability suppress their practical application. Here, we creatively propose a water-driven synthesis strategy to obtain size-homogenized and strongly confined deep-blue CsPbBr₃ QWs, corresponding to three monolayers, which emit at the deep-blue wavelength of 456 nm. The water controls the orientation and distribution of the ligands on the surface of the nanocrystals, thus inducing orientated growth through the Ostwald ripening process by phagocytizing unstable nanocrystals to form well-crystallized QWs. These QWs present remarkable stability and high photoluminescence quantum yield of 94 %. Furthermore, we have prepared light-emitting diodes based on the QWs via the all-solution fabrication strategy, achieving an external quantum efficiency of 1 % and luminance of 2946 cd m⁻², demonstrating state-of-the-art brightness for perovskite QW-based LEDs.     

Highly efficient green organic light-emitting diodes containing luminescent three-coordinate copper(I) complexes

A series of highly emissive three-coordinate copper(I) complexes, (dtpb)Cu(I)X [X = Cl (1), Br (2), I (3); dtpb =1,2-bis(o-ditolylphosphino)benzene], were synthesized and investigated in prototype organic light-emitting diodes (OLEDs). 1-3 showed excellent photoluminescent performance in both degassed dichloromethane solutions [quantum yield (Φ) = 0.43-0.60; lifetime (τ) = 4.9-6.5 μs] and amorphous films (Φ = 0.57-0.71; τ = 3.2-6.1 μs). Conventional OLEDs containing 2 in the emitting layer exhibited bright green luminescence with a current efficiency of 65.3 cd/A and a maximum external quantum efficiency of 21.3%.     

Blue-light-emitting multifunctional triphenylamine-centered starburst quinolines: synthesis, electrochemical and photophysical properties

A series of triphenylamine-centered starburst quinolines (1a-1g) have been synthesized by Friedl?nder condensation of the 4,4',4'-triacetyltriphenylamine (2) and 2-aminophenyl ketones (3a-3g) in the presence of catalytic sulfuric acid and characterized well. They are thermally robust with high glass transition temperatures (above 176.4 °C) and decomposition temperatures (above 406 °C). These compounds emit blue fluorescence with λ(max)(Em) ranging from 433 to 446 nm in dilute toluene solution and 461 to 502 nm in the solid-state and have a relatively high efficiency (Φ(u) = 0.98-0.57). 1a-1g have estimated ionization potentials (IP) of 4.54 to 6.45 eV which are significantly near or higher than those of well-known electron transport materials (ETMs), including tris(8-hydroxyquinoline)aluminium (Alq(3)) (IP = 5.7-5.9 eV), and previously reported oligoquinolines (IP = 5.53-5.81 eV). Quantum chemical calculations using DFT B3LYP/6-31G* showed the highest occupied molecular orbital (HOMO) of -5.05 to -4.81 eV, which is close to the work function of indium tin oxide (ITO). These results demonstrate the potential of 1a-1g as hole-transporting/light-emitting/electron-transport materials and the host-materials of a dopant for hole-injecting for applications in organic light-emitting devices.     

Fluorene-based donor-acceptor-type multifunctional polymer with bicarbazole pendant moiety for optoelectronic applications

Since limited examples are in the literature in which both organic light-emitting diodes (OLEDs) and electrochromic (EC) applications were performed using the same conjugated polymer, we presented comprehensive EC and electroluminescence (EL) studies of fluorene-based electroactive polymer (e.g., CFP6) consisting of a bicarbazole pendant moiety with quinoxaline as an acceptor bridge. CFP6 was synthesized by a Suzuki cross-coupling polymerization reaction and utilized as an active and emissive layers of the electrochromic device (ECD) and OLED, respectively, due to its high photoluminescence quantum yield intensity and fine thin film forming capability. The optical, electrochemical, cyclic voltammetry measurements, and density functional theory calculations were realized. Electrochemical cross-linking process was applied over the electroactive carbazole subunit of the CFP6 polymer. After the crosslinking process, EC performance was greatly improved. On the other hand, light emission and EL characteristics of OLEDs based on CFP6 emissive layer were realized in detail with six different device architectures to understand light output profile behavior. As a result, CFP6 emitted bright greenish yellow emission with a maximum brightness of 1777 cd/m² at 215 mA/cm² in the indium tin oxide (ITO)/poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS)/CFP6:%10 4,4′-bis(N-carbazolyl)-1,1′-biphenyl (CBP)/Alq3/LiF/Al device architecture.     

Synthesis of a green-emitting alternating block copolymer

An alternating block copolymer, poly(1,8-octanedioxy-2,6-dimethoxy-1,4-phenylene-1,2-ethenylene-1,4-phenylene-1,2-ethenylene-1,4-phenylene-1,2-ethenylene-3,5-dimethoxy-1,4-phenylene), 1 , was synthesized, and characterized using Fourier transform infrared spectroscopy, nuclear magnetic resonance, gel permeation chromatography differential scanning calorimetry ultraviolet and elemental analysis. Light-emitting single-layer test diodes using this soluble, processible copolymer as the active layer (i.e. indium tin oxide/ 1 /Ca,Al) emit green light with a luminescent spectral maximum at 513 nm. The single-layer device had a brightness of about 80 cd/m² at a current density of 100 mA/cm² with an internal quantum efficiency of 0.3% photon/electron. Optimization of the light-emitting properties of 1 was achieved through variation of a key Wittig polymerization step in the synthesis, using trialkyl rather than triaryl phosphonium salts in an appropriate solvent mixture to achieve nearly regiospecific trans-olefination. This provided an improvement over earlier procedures, which require a post-Wittig isomerization to minimize the presence of electroluminescence-inhibiting cis-bonds. © 1998 John Wiley & Sons, Ltd.     

High‐Performance Perovskite Light‐Emitting Diode with Enhanced Operational Stability Using Lithium Halide Passivation

Defect passivation has been demonstrated to be effective in improving the radiative recombination of charge carriers in perovskites, and consequently, the device performance of the resultant perovskite light‐emitting diodes (LEDs). State‐of‐the‐art useful passivation agents in perovskite LEDs are mostly organic chelating molecules that, however, simultaneously sacrifice the charge‐transport properties and thermal stability of the resultant perovskite emissive layers, thereby deteriorating performance, and especially the operational stability of the devices. We demonstrate that lithium halides can efficiently passivate the defects generated by halide vacancies and reduce trap state density, thereby suppressing ion migration in perovskite films. Efficient green perovskite LEDs based on all‐inorganic CsPbBr₃ perovskite with a peak external quantum efficiency of 16.2 %, as well as a high maximum brightness of 50 270 cd m^?2, are achieved. Moreover, the device shows decent stability even under a brightness of 10⁴ cd m^?2. We highlight the universal applicability of defect passivation using lithium halides, which enabled us to improve the efficiency of blue and red perovskite LEDs.     

Polycyclic aromatic hydrocarbon-bridged coumarin derivatives for organic light-emitting devices

Three biscoumarin dyes bridged by polycyclic aromatic bridges (anthracen, pyrene and dibenzo[g,p]chrysene) were prepared as the emissive materials for the application of organic light-emitting devices. The relationship between their structures, photophysical properties, electrochemical properties and performances of organic light-emitting devices are described. The multilayered doped devices with a configuration of ITO/NPB (20 nm)/TBADN: biscoumarin compound (x wt%, 30 nm)/TPBi (30 nm)/Liq (2 nm)/Al (100 nm) have been successfully fabricated by vacuum-deposition method. All the devices showed green emission with high electroluminescent efficiencies. Especially, the device based on the compound containing pyrene as a bridge group at 7% doping concentration showed the best performance with a maximum brightness of 10552 cd/m², maximum luminous efficiency of 5.39 cd/A and maximum external quantum efficiency (EQE) of 2.35%.     

Simple Silole‐Containing Polyfluorene for White Electroluminescence with Simultaneous Blue,Green, and Red Emission

Novel conjugated silole‐containing polyfluorenes, with green‐ and red‐emissive siloles on the backbone of the blue‐emissive polyfluorene are synthesized for white light electroluminescence (EL) from a single polymer with simultaneous red, green, and blue (RGB) emission. The CIE coordinates (0.33, 0.36) of the white light EL spectra are very close to that for pure white light (0.33, 0.33). The EL spectra are also quite stable at different applied voltages or brightness. The relative intensities for the three RGB peaks, at 450, 505, and 574 nm, were 0.94, 1, and 0.97, respectively, which demonstrates a balanced simultaneous RGB emission. A maximum luminous efficiency of 2.03 cd · A⁻¹ for a brightness of 344 cd · m⁻², and a luminous efficiency of 1.86 cd · A⁻¹ for a more practical brightness of 2 703 cd · m⁻², were achieved.

     

Synthesis, photophysical and electrophosphorescent properties of fluorene-based platinum(II) complexes

A series of platinum(II) complexes bearing tridentate cyclometalated C^N^N (C^N^N=6-phenyl-2,2'-bipyridine and π-extended R-C^N^N=3-[6'-(naphthalen-2'-yl)pyridin-2'-yl]isoquinoline) ligands with fluorene units have been synthesised and their photophysical properties have been studied. The fluorene units are incorporated into the cyclometalated ligands by a Suzuki coupling reaction. An increase in the π-conjugation of the cyclometalated ligands confers favourable photophysical properties compared to the 6-phenyl-2,2'-bipyridine analogues. The fluorene-based platinum(II) complexes display vibronic-structured emission bands with λ(max)=558-601 nm, and high emission quantum yields up to 0.76 in degassed dichloromethane. Their emissions are tentatively assigned to excited states with mixed (3)IL/(3)MLCT parentage (IL=intraligand, MLCT=metal-to-ligand charge transfer). The crystal structures of these platinum(II) complexes reveal extensive Pt(II)···π and/or π-π interactions. The fluorene-based platinum(II) complexes are soluble in organic solvents, have high thermal stability with decomposition temperature >350 °C, and can be thermally vacuum-sublimed or solution-processed as phosphorescent dopants for the fabrication of organic light-emitting diodes (OLEDs). A monochromic OLED with 3d as dopant (2 wt%) fabricated by vacuum deposition gave a current efficiency of 14.7 cd A(-1) and maximum brightness of 27000 cd m(-2). A high current efficiency (9.2 cd A(-1)) has been achieved in a solution-processed OLED using complex 3f (5 wt%) doped in a PVK (poly(9-vinylcarbazole)) host.     

A class of fascinating optoelectronic materials: Triarylboron compounds

Triarylboron compounds are significant optoelectronic materials due to their excellent emissive and electron-transport properties,and could be applied in organic light-emitting diodes as emissive and/or electron-transport layers.Triarylboron compounds have vacant pπ orbital and have received increasing interest as fluoride ion and cyanide ion sensors utilizing specific Lewis acid-base interaction.This review summarizes their structural characteristics,optical properties and applications in chemosensors for anions and optoelectronic devices developed in recent years and discusses the problems and prospects.     

含芳胺和1,3,4-噁二唑的星型有机分子合成及光电性质

通过分子设计, 采用多步反应合成了2种新型的具有“双极”(Bipolar)性质和发光性能的以N原子为中心的星型有机分子. 用1H NMR, MS和元素分析进行了表征, 研究了化合物的热稳定性和固体粉末的光致发光性质, 并用循环伏安法测定了其电化学性能. 结果表明, 这种同时具备空穴传导和电子输入双重功能基团的星型有机小分子的光致发光性能优良(量子效率达到82%—95%), 热稳定性好, 可以作为有机电致发光器件材料.     

Solid-state highly fluorescent diphenylaminospirobifluorenylfumaronitrile red emitters for non-doped organic light-emitting diodes

Bright (maximum 11,000 cd m(-2) and 500 cd m(-2) at 20 mA cm(-2)) and efficient (maximum external quantum efficiency of 3.1% at 1 mA cm(-2)) red (CIE, x = 0.66, y = 0.34) organic light-emitting diodes (OLEDs) employ arylaminospirobifluorene-substituted fumaronitriles as the novel non-dopant red emitter.     

Red phosphorescent organic light-emitting diodes based on a novel host material with thermally activated delayed fluorescent properties

High cost of phosphors and significant efficiency roll-off at high brightness are the two main factors that limit the wide application of phosphorescent organic light-emitting diodes (PHOLEDs). Efforts have been paid to find ways to reduce the phosphors’ concentration and efficiency roll-off of PHOLEDs. In this work, we reported red emission PHOLEDs with low dopant concentration and low efficiency roll-off based on a novel host material 2,4-biscyanophenyl-6-(12-phenylindole[2,3-a]carbazole-11-yl)-1,3,5-triazine (BCPICT), with thermally activated delayed fluorescent(TADF) properties. The device with 1.0% dopant concentration displayed a maximum external quantum efficiency of 10.7%.When the dopant concentration was increased to 2.0%, the device displayed a maximum external quantum efficiency of 10.5% and a low efficiency roll-off of 5.7% at 1000 cd/m2.     

Performance and defects in phosphorescent organic light-emitting diodes

Phosphorescent heavy metal complexes can utilize both singlet and triplet excitons and thus are interesting for doping polymer to obtain highly efficient organic light-emitting diodes. In this study, we have investigated devices using a new phosphorescent–metal complex containing fluorene and platinum added to a luminescent polymer blend, composed of 2-(4-biphenylyl)-5-(4-tert-butyl-phenyl)-(1,3,4-oxadiazole) (PBD) and poly(9-vinylcarbazole) (PVK). The performance of devices (luminance and yield) is measured in indium tin oxide (ITO)/poly(3-4 ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS)/(PVK–PBD-complex)/Al diodes. The devices emit an orange light with a brightness of 607 cd/m² and an external quantum efficiency of 0.28 cd/A at 25 V. In order to investigate the structural modifications of the polymer by the incorporation of phosphorescent–metal complex, we have studied the defect states in diodes by charge-based Deep Level Transient Spectroscopy (Q-DLTS). Analysis of Q-DLTS spectra obtained in undoped and doped devices, revealed at least three trap levels distributed in the range 0.2–0.5 eV within the band gap of the hybrid composite with trap density in the range around 10¹⁶ cm^?3. Incorporation of Pt complex into the polymer blend modified the trap states by reducing the density of traps in the blend and by creating new trap levels in the band gap.     

A luminescent cyclometalated platinum(II) complex and its green organic light emitting device with high device performance

A luminescent cyclometalated platinum(II) complex has been demonstrated to show green electrophosphorescence in multilayer organic light-emitting devices (OLEDs) using a dual emissive layer with high current and external quantum efficiencies of 38.9 cd A(-1) and 11.5%, respectively.