有两种故障状态的两部件串联系统的预防维修策略

本文研究的是由两个部件串联组成且有两种故障状态的系统的预防维修策略, 当系统的工作时间达到T时进行预防维修, 预防维修使部件恢复到上一次故障维修后的状态。每个部件发生故障都有两种状态, 可维修和不可维修。当部件的故障为可维修故障时, 修理工对其进行故障维修, 且每次故障维修后的工作时间形成随机递减的几何过程, 每次故障后的维修时间形成随机递增的几何过程。当部件发生N次可维修故障或一次不可维修故障时进行更换。以部件进行预防维修的间隔和更换前的可维修故障次数N组成的二维策略(T, N) 为策略, 利用更新过程和几何过程理论求出了系统经长期运行单位时间内期望费用的表达式, 并给出了具体例子和数值分析。     

具有不同失效率和修理率的n中连续取k的可修系统

研究了具有不同失效率和修理率的,2中连续取k的可修系统．在假设失效部件的修理规则为后到先修,且修复如新的条件下,得到了具有不同失效率和修理率的n中连续取k的可修系统各状态的概率,并进一步获得了这类可修系统的一些重要的可靠性指标或者其Laplace变换．     

修理设备可更换的k/n(G)表决可修系统

研究了修理设备可更换的k/n(G)表决可修系统,其中修理设备在修理故障部件时可能发生失效.假定部件和修理设备的寿命服从负指数分布,故障部件的修理时间和修理设备的更换时间服从一般分布的条件下,利用马尔可夫更新过程理论和拉普拉斯变换(Laplace-Stieltjes变换),分别讨论了系统首次故障前的平均时间,可用度,故障频度及修理设备的不可用度和失效频度,获得了相关指标的递推表达式.在此基础上,给出了1/2(G)表决可修系统和(n-1)/n(G)表决可修系统相关可靠性指标的表达式.     

修理设备可更换和修理延迟的两类故障状态并联可修系统

考虑两同型部件组成的并联可修系统,每个部件有两类故障状态,部件故障后修理有延迟,且修理设备在修理故障部件的过程中也可能发生故障.假定部件的寿命和修理设备的寿命服从指数分布,部件发生故障后的修理延迟时间、修理时间和修理设备故障后的更换时间均服从一般分布,利用马尔可夫更新过程理论和拉普拉斯变换工具,求得了系统有关的可靠性指标.     

基于几何过程和位相分布休假的两部件并联可修系统的可靠性分析

主要以两不同型部件组成的并联可修系统为研究对象.在系统对失效相位存在记忆的基础上,考虑了修理工可单重休假且休假时间服从位相(PH)分布.每个工作部件均有可能因受到两种不同类型的故障而失效,且均"修复非新".在假定部件的工作时间,修理时间分别服从PH分布的几何过程和负指数分布的条件下,利用马尔可夫过程和矩阵分析的方法,对可修系统进行了可靠性分析,并给出了相应可靠性指标的数值算例.     

Mixture representation for the residual lifetime of a repairable system

In this paper, we consider a repairable system in which two types of failures can occur on each failure. One is a minor failure that can be corrected with minimal repair, whereas the other type is a catastrophic failure that destroys the system. The total number of failures until the catastrophic failure is a positive random variable with a given probability vector. It is assumed that there is some partial information about the failure status of the system, and then various properties of the conditional probability of the system failure are studied. Mixture representations of the reliability function for the system in terms of the reliability function of the residual lifetimes of record values are obtained. Some stochastic properties of the conditional probabilities and the residual lifetimes of two systems are finally discussed. Copyright © 2017 John Wiley & Sons, Ltd.     

专职修理工多重休假且修理设备可更换的k/n(G)表决系统研究

讨论专职修理工多重休假,修理设备可发生失效且可更换的k/n（G）表决可修系统.当系统中没有故障部件时,专职修理工开始一次休假,在此期间,若有工作部件发生故障,则立即指派普通修理工修理故障部件,一直持续到系统中无故障部件或专职修理工休假回来.利用马尔可夫过程理论和矩阵解法,给出了系统瞬态和稳态下的可用度和故障频度、可靠度、系统首次故障前的平均时间、修理设备处于更换状态的概率等指标的表达式.在此基础上,基于不同的初始条件研究了相关指标随时间的变化情况.最后,特殊情形的讨论验证了所得结果的正确性.     

故障相关的表决可修系统可用度计算

为解决k/n(F)表决可修系统中零部件的故障相关干涉问题,根据零部件工作寿命之间的正相关结构,运用Copula函数的相关性理论,提出微时间差t→t+Δt内系统一步状态转移矩阵概念,建立了故障相关的表决可修系统可靠性模型.模型全面考虑了共因故障、零件工作寿命和修复时间分布的一般性,从而突破传统独立指数型可修系统可靠性模型的三类局限性.验证了k/n(F)可修系统相关性模型的通用性,给出了Copula模型选择和估计相关程度参数的方法.     

Optimal repair–replacement policies for a system with two types of failures

In this paper, the optimal replacement problem is investigated for a system with two types of failures. One type of failure is repairable, which is conducted by a repairman when it occurs, and the other is unrepairable, which leads to a replacement of the system at once. The repair of the system is not “as good as new”. The consecutive operating times of the system after repair form a decreasing geometric process, while the repair times after failure are assumed to be independent and identically distributed. Replacement policy N is adopted, where N is the number of repairable failures. The system will be replaced at the Nth repairable failure or at the unrepairable failure, whichever occurs first. Two replacement models are considered, one is based on the limiting availability and the other based on the long-run average cost rate of the system. We give the explicit expressions for the limiting availability and the long-run average cost rate of the system under policy N, respectively. By maximizing the limiting availability A(N) and minimizing the long-run average cost rate C(N), we theoretically obtain the optimal replacement policies N^∗ in both cases. Finally, some numerical simulations are presented to verify the theoretical results.     

具有单重休假和修复不如新的两部件并联系统

为了解决由"修复非新"部件组成的具有休假的可修型系统,运用几何过程理论、补充变量法和拉普拉斯变换工具,研究了由两个不同型部件和一个修理工组成的可修型并联系统.假设两个部件的工作寿命和修理时间均服从不同的指数分布,修理工可休假,对部件1的修理是几何修理而对部件2的修理则是修复如新,得到了系统的可用度、可靠度和系统首次故障前平均时间等可靠性指标.成果具有一定的理论和实际意义.     

修复率可变化的表决系统可靠性分析

研究了具有维修速率可变化的k/n(G)表决可修系统,其中部件的工作时间和修理时间均服从负指数分布.开始时,当系统中的故障部件数小于某一阈值L时,修理工以较低的维修率修理故障的部件.如果修理工修理工作进展不顺利,故障部件数增加到阈值L时,将立即以较快的速度修理故障部件,此状态一直持续到系统中没有故障部件为止.使用马尔可夫过程理论和分析方法,得到了系统可用度、故障频度、系统首次故障前的平均时间等指标的表达式.进一步,讨论了不同条件下系统相关指标随系统参数变化的情况,并通过对特殊情形的讨论数值验证了所得结果的正确性.     

The average optimality of a repair-limit replacement policy

We consider a minimal-repair and replacement problem of a reliability system whose state at a failure is described by a pair of two attributes, i.e., the total number of its past failures and the current failure level. It is assumed that the system is bothered by more frequent and more costly failures as time passes. Our problem is to find and/or characterize a minimal-repair and replacement policy of minimizing the long-run average expected maintenance cost per unit time over the infinite time horizon. Formulating the problem as a semi-Markov decision process, we show that a repairlimit replacement policy is average optimal. That is, for each total number of past system failures, there exists a threshold, called a repair limit, such that it is optimal to repair minimally if the current failure level is lower than the repair limit, and to replace otherwise. Furthermore, the repair limit is decreasing in the total number of past system failures.     

可修C(2,3:F)系统的可靠性分析

考虑了由三个部件和一个维修工组成的线形可修系统.假定可修系统中的三个部件是相互独立的,每个部件的工作时间和维修时间均服从负指数分布.部件故障后不能修复如新以及关键部件具有优先维修权的情形下,利用几何过程与广义马尔可夫过程等数学工具对该系统的可靠性指标进行了深入的研究.我们得到了该系统的瞬时可用度,可靠度的L ap lace变换表达式.从而得到系统的稳态可用度及首次故障前的平均时间.为进一步探索线形可修系统、复杂串并联和复杂并串联系统提供了一条新途径.     

A deteriorating cold standby repairable system with priority in use

In this paper, a cold standby repairable system consisting of two dissimilar components and one repairman is studied. In this system, it is assumed that the working time distributions and the repair time distributions of the two components are both exponential and component 1 is given priority in use. After repair, component 2 is “as good as new” while component 1 follows a geometric process repair. Under these assumptions, using the geometric process and a supplementary variable technique, some important reliability indices such as the system availability, reliability, mean time to first failure (MTTFF), rate of occurrence of failure (ROCOF) and the idle probability of the repairman are derived. A numerical example for the system reliability R(t) is given. And it is considered that a repair-replacement policy based on the working age T of component 1 under which the system is replaced when the working age of component 1 reaches T. Our problem is to determine an optimal policy T^∗ such that the long-run average cost per unit time of the system is minimized. The explicit expression for the long-run average cost per unit time of the system is evaluated, and the corresponding optimal replacement policy T^∗ can be found analytically or numerically. Another numerical example for replacement model is also given.     

A general model for consecutive-k-out-of-n: F repairable system with exponential distribution and (k−1)-step Markov dependence

In this paper, a general model for consecutive-k-out-of-n: F repairable system with exponential distribution and (k−1)-step Markov dependence is introduced. The lifetime of a component is an exponential random variable, its parameter depends on the number of consecutive failed components that precede the component. The repair time is also an exponential random variable. A priority repair rule on the basis of the system failure risk is adopted. Then the transition density matrix of the system is determined. Some reliability indices, including the system availability, rate of occurrence of failures and reliability are evaluated accordingly. For the demonstration of the model and methodology, a linear system example and a circular system example are investigated.     

退化可修系统最优更换数学模型研究

研究了单部件组成的退化可修系统,在假定故障部件“修复非新”的条件下,以系统中部件的故障次数N为更换策略进行了研究,我们推导出系统经长期运行后,单位时间内期望效益的明显表达式,而且在一定条件下证明了最优策略N*是所有更换策略中最优的.最后还通过几何过程对此进行了讨论.     

开关寿命连续型二部件温贮备可修系统的可靠性分析

本文对由2个部件组成的开关寿命为连续随机变量的温贮备可修系统,当部件的工作时间和维修时间以及转换开关的寿命和修理时间均服从指数分布,所有随机变量均相互独立,故障部件和转换开关能修复如新的情况下作了可靠性分析,建立了该类系统模型,给出了系统可靠度R（t)和首次故障前的平均时间MTTFF的解析表达式。     

Optimum Burn-in Time for a Bathtub Shaped Failure Distribution

An important problem in reliability is to define and estimate the optimal burn-in time. For bathtub shaped failure-rate lifetime distributions, the optimal burn-in time is frequently defined as the point where the corresponding mean residual life function achieves its maximum. For this point, we construct an empirical estimator and develop the corresponding statistical inferential theory. Theoretical results are accompanied with simulation studies and applications to real data. Furthermore, we develop a statistical inferential theory for the difference between the minimum point of the corresponding failure rate function and the aforementioned maximum point of the mean residual life function. The difference measures the length of the time interval after the optimal burn-in time during which the failure rate function continues to decrease and thus the burn-in process can be stopped.      

A bivariate optimal replacement policy for a cold standby repairable system with preventive repair

In this paper, the repair-replacement problem for a deteriorating cold standby repairable system is investigated. The system consists of two dissimilar components, in which component 1 is the main component with use priority and component 2 is a supplementary component. In order to extend the working time and economize the running cost of the system, preventive repair for component 1 is performed every time interval T, and the preventive repair is “as good as new”. As a supplementary component, component 2 is only used at the time that component 1 is under preventive repair or failure repair. Assumed that the failure repair of component 1 follows geometric process repair while the repair of component 2 is “as good as new”. A bivariate repair-replacement policy (T, N) is adopted for the system, where T is the interval length between preventive repairs, and N is the number of failures of component 1. The aim is to determine an optimal bivariate policy (T, N)^∗ such that the average cost rate of the system is minimized. The explicit expression of the average cost rate is derived and the corresponding optimal bivariate policy can be determined analytically or numerically. Finally, a Gamma distributed example is given to illustrate the theoretical results for the proposed model.     

Reliability analysis of a k-out-of-n:G repairable system with single vacation

This paper analyzes a k-out-of-n:G   repairable system with one repairman who takes a single vacation, the duration of which follows a general distribution. The working time of each component is an exponentially distributed random variable and the repair time of each failed component is governed by an arbitrary distribution. Moreover, we assume that every component is “as good as new” after being repaired. Under these assumptions, several important reliability measures such as the availability, the rate of occurrence of failures, and the mean time to first failure of the system are derived by employing the supplementary variable technique and the Laplace transform. Meanwhile, their recursive expressions are obtained. Furthermore, through numerical examples, we study the influence of various parameters on the system reliability measures. Finally, the Monte Carlo simulation and two special cases of the system which are (n-1)$(n-1)$-out-of-n:G repairable system and 1-out-of-n:G repairable system are presented to illustrate the correctness of the analytical results.