首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到19条相似文献,搜索用时 828 毫秒
1.
抽油杆杆体及过渡段的剩余寿命研究   总被引:2,自引:1,他引:2  
本文通过抽油杆材料疲劳裂纹扩展速率及抽油杆工作载荷的研究,对抽油杆杆体及过渡段存在表面缺陷时的剩余寿命进行了分析、推导、计算,得到了便于工程应用的剩余寿命图线,为抽油杆缺陷评定提供了依据。  相似文献   

2.
应用新的应力强度因子经验公式预测了拉伸和纯弯曲载荷下疲劳扩展过程中表面裂纹形状的演化,并与Newman和Raju的经验公式以及实验结果进行了比较。结果表明:虽然对应力强度因子估算有一定差别,但两者对裂纹形状演化的预测有很好的一致性,预测结果与实验结果也比较吻合,从而表明所提出的经验公式能够用于预测疲劳扩展过程中表面裂纹形状演化。  相似文献   

3.
根据Paris疲劳裂纹扩展规律,对拉伸和纯弯曲疲劳载荷下表面裂纹扩展进行了数值模拟。数值模型中,用三次样条函数曲线拟合裂纹尖端,在裂纹扩展增量计算中考虑了裂纹闭合影响。裂纹形状演化的模拟结果与Newman和Raju经验公式预测结果进行了比较,表明了所采用的数值模拟方法的实用性。研究发现,裂纹闭合对疲劳裂纹扩展过程中的裂纹形状演化以及裂纹尖端的应力强度因子(SIF)分布都有明显影响。同裂纹形状演化一样,疲劳裂纹扩展过程中裂纹尖端的SIF分布表现出明显的特征。最后,建议了一个简单函数来统一描述表面裂纹尖端的SIF分布。  相似文献   

4.
以Donahue等提出的疲劳裂纹扩展速率计算模型为基础,通过引入形状系数、张开比和残余应力等参数,建立了适用于焊接结构的疲劳裂纹扩展速率计算模型,分析了多种因素对焊接结构疲劳裂纹扩展速率的影响规律。结果表明,焊板厚度和焊缝余高的变化均会对焊接结构疲劳裂纹的扩展速率产生影响,在对焊接结构表面形状进行设计时应保有一定的焊缝余高;有效应力比的增大会降低焊接结构疲劳裂纹的扩展速率,且裂纹深度的变化不会改变有效应力比对焊接结构疲劳裂纹扩展速率的影响;残余应力的增大会提高焊接结构疲劳裂纹的扩展速率,且残余应力对疲劳裂纹扩展速率的促进作用随着裂纹深度的增加而增大,在对焊接结构的疲劳性能进行设计时须考虑残余应力对结构性能的影响。  相似文献   

5.
论文采用超声疲劳试验技术测试了发动机曲轴用球墨铸铁的超高周疲劳强度及超声疲劳载荷下的裂纹扩展速率.考虑高频载荷下疲劳裂纹扩展过程中的温升效应,测试了球墨铸铁超声疲劳裂纹扩展过程中的温度变化,研究了超声微幅循环载荷下球墨铸铁的疲劳裂纹萌生与扩展机制.根据超声疲劳试验控制位移的加载特点及超声疲劳试样几何形状特征,数值计算了超声疲劳裂纹扩展应力强度因子,给出了该球墨铸铁超声疲劳裂纹扩展速率曲线.  相似文献   

6.
对晶界平行裂纹和晶界垂直裂纹的双晶体进行三点弯曲疲劳实验,研究了双晶材料的疲劳裂纹扩展规律,测定了双晶的疲劳扩展速率,揭示了晶界对晶粒疲劳裂纹扩展的屏蔽效应:当裂纹距晶界某一特定长度时,裂纹扩展速率最快;而裂纹顶端交于晶界时,裂纹扩展速率最侵.进一步的晶体滑移有限元数值分析揭示了这种屏蔽效应的机理:晶界附近不协调的塑性变形,导致了裂纹尖端应力场的重新分布.  相似文献   

7.
疲劳裂纹形成、扩展统计特性的大子样试验研究   总被引:1,自引:0,他引:1  
针对疲劳损伤过程的随机性,该文开展了等幅谱大子样疲劳裂纹形成、扩展至破坏全寿命过程的试验研究.在计算确立了裂纹形成、扩展分界工程小裂纹长度的基础上,整理得到了裂纹形成,扩展寿命的统计分布数据.根据断口金相SEM观察,进一步定性分析了疲劳条纹分布的相关性特征.  相似文献   

8.
考虑材料循环塑性的疲劳裂纹扩展模拟   总被引:1,自引:1,他引:1  
提出了一种考虑材料循环塑性性能的研究疲劳裂纹扩展与闭合行为的有限元模拟方法.对所选用的循环塑性本构关系进行了基本实验检验.探讨了在疲劳裂纹扩展有限元分析中网格尺寸的影响,给出了网格优化准则.研究了在循环硬化条件下考虑裂纹合效应时裂纹面张开廓形、裂纹尖端应力、应变场和正反向塑性区的演变规律.对于循环硬化和不同循环应力比R等因素对裂纹张开应力水平的影响也作了考察  相似文献   

9.
本文提出了裂纹在硬区的软对硬不均匀裂纹体的力学分析模型.疲劳实验研究表明,这种不均匀性影响疲劳裂纹扩展速率.文中的疲劳载荷下不均匀裂纹体的边界元数值计算结果表明,随着疲劳裂纹的扩展,在相同扩展步下,裂纹距软硬区界面越近,裂纹张开位移的幅值△COD 越小,J 积分幅值△J 亦越小.不均匀性对疲劳裂纹扩展速率的影响,主要通过影响△J 来实现.裂纹与软硬区界面的距离越近,疲劳裂纹扩展速率越小.  相似文献   

10.
飞机谱载下铝合金锪窝孔结构腐蚀疲劳研究   总被引:5,自引:0,他引:5  
通过战斗机谱载下7475—T761铝合金紧固孔试件空气与3.5%NaCl环境中的疲劳试验和断口分析,得到了相应结构疲劳全寿命和孔边角裂纹的裂纹长度-寿命数据.通过三维有限元分析得到了孔边角裂纹的应力强度因子.采用我们新近发展的三维疲劳寿命分析软件,基于材料裂纹扩展基准曲线和一组直通孔实验数据,对锪窝孔结构角裂纹的疲劳和腐蚀疲劳扩展寿命进行了预测.结果表明,提出的基于三维断裂力学的寿命预测方法和软件对复杂结构的全寿命有精确的预测能力,比传统的局部应变法优越,可适用于复杂环境下三维结构的疲劳寿命分析.  相似文献   

11.
Fatigue crack growth behavior of in-plane gusset welded joints is studied using the strain energy density factor approach. Fatigue tests were performed in order to estimate fatigue strength under tension. Fatigue crack growth analysis was carried out to show the effects of the initial crack shape, the initial crack length, and the stress ratio on the crack types of in-plane gusset welded joints. The assumed crack types were edge crack, semi-elliptical crack, and corner crack. Fatigue crack growth parameters were obtained from crack growth curves assuming constant crack shapes for the given crack types. The results of analysis for the assumed crack types agreed well with the experimental data. The fatigue life did not change as initial crack shape varied for a given initial crack length.  相似文献   

12.
Fatigue growth behavior of out-of-plane gusset welded joints is studied using the strain energy density factor approach. Fatigue tests on two types of specimens with curvatures of ρ = 0 and ρ = 30 were performed in order to estimate fatigue strength under tension. Fatigue crack growth analysis is carried out to show the effects of initial crack shape, initial crack length and stress ratio. Fatigue crack growth parameters were obtained from crack growth curves assuming constant crack shapes. The results of analysis for the assumed crack shapes agreed well with the experimental data. Fatigue propagation life of the ρ = 30 specimen was larger than that of the ρ = 0 specimen.  相似文献   

13.
Three-dimensional crack closure correction methods are investigated in this paper.The fatigue crack growth tests of surface cracks in 14MnNbq steel for bridge plate subjected to tensile and bending loadings are systematically conducted.The experimentally measured fatigue crack growth rates of surface cracks are compared with those of through-thickness cracks in detail.It is found that the crack growth rates of surface cracks are lower than those of through-thickness cracks.In order to correct their differences in fatigue crack growth rates, a dimensionless crack closure correction model is proposed.Although this correction model is determined only by the experimental data of surface cracks under tensile loading with a constant ratio R=0.05, it can correlate the surface crack growth rates with reasonable accuracy under tensile and bending loadings with various stress ratios ranging from 0 to 0.5.Furthermore, predictions of fatigue life and crack aspect ratio for surface cracks are discussed, and the predicted results are also compared with those obtained from other prediction approaches.Comparison results show that the proposed crack closure correction model gives better prediction of fatigue life than other models.  相似文献   

14.
论文针对中密度聚乙烯材料(MDPE),采用平板试样进行了I型疲劳裂纹扩展和单次过载下裂纹扩展试验.发现与金属材料类似,单次拉伸过载对聚乙烯(PE)的疲劳裂纹扩展有明显的迟滞作用,降低了裂纹扩展速率.试验还通过变载荷刻线法获取疲劳裂纹扩展前缘的实际形貌和变化规律,对常规变载荷刻线方法进行了调整和验证,其修正方法对高分子材料的疲劳裂纹扩展前缘刻线具有较好的效果.通过观察发现含楔形塑性区的裂尖钝化是裂纹迟滞的主要原因.过载引入的塑性区内残余应力对裂纹迟滞也起了重要作用.论文利用Dugdale模型计算了塑性区尺寸,使用基于残余应力的Wheeler模型对过载迟滞进行了很好的拟合.  相似文献   

15.
查子初  王志群 《实验力学》1991,6(2):169-176
本文提供了一种可以进行自增强处理的圆筒试样,通过实验用柔度法确定了该试样的表面裂纹的应力强度因子,介绍了含表面裂纹试样的柔度测试技术,导出了柔度与表面裂纹尖端前缘各点的应力强度因子的关系式,该式可作为各种含表面裂纹试样柔度法测表面裂纹 K_1因子的参考,本文还测定了不同自增强程度下,自增强圆筒的表面裂纹疲劳扩展规律。  相似文献   

16.
In this paper, a circumferential external surface flaw in a metallic round pipe under cyclic bending loading is considered. Because of very rapid changes in the geometrical parameters around the crack front region, the mesh generation of this region must be done with great care. This may lead to an increase in the run time which makes it difficult to reach valid results and conclusions. Because of the advantages of the sub-modeling technique in problems which need very high mesh density, this method is used. Stress intensity factors in mode I condition are determined using three-dimensional finite element modeling with 20 node iso-parametric brick elements in the ANSYS 9.0 standard code and the singular form of these finite elements at the crack front. In order to estimate the analysis error, the structural parameter error in energy norm criterion was used. Because of the advantages of non-dimensional analysis, this method is employed, and the stress intensity factors are normalized. For the analysis of the fatigue crack growth, the Paris law is used. The propagation path of the surface flaw is obtained from the diagram of aspect ratio versus relative crack depth. The fatigue crack growth analysis (the relative crack depth against loading cycles diagram) of different initial crack aspect ratio under cyclic loading is also considered. Fatigue shape development of initially semi-elliptical external surface defects is illustrated. The effect of the Paris exponent (material constant) on fatigue crack propagation is shown as well. Moreover, the fatigue crack growth of several specimens is assessed experimentally using a manually-constructed experimental set up. Finally, the experimental results obtained by cyclic bending loading tests are compared with the numerical results. The experimental results show good conformity with the finite element results.  相似文献   

17.
18.
The semi-elliptical surface crack growth of structural components withuncertain material resistance under random loading is studied by using the stochasticaveraging principle.The FPK equation governing the transition probability densityfunction of crack lengths is derived.The analytical solution of the FPK equation forthe case of that the equations for the crack growth in the surface and depth directionsare uncoupled is obtained.The effects of the parameters of the stress process and of thematerial property on the behavior of semi-elliptical fatigue crack growth of thecomponents with deterministic resistance to crack growth in the stationary Gaussianstress process are examined.The comparison of the analytical result with digitalsimulation shows the effectiveness of the present method.  相似文献   

19.
本文应用随机平均原理研究了在随机载荷作用下具有随机抗裂特性的构件所含半椭圆型表面裂纹的疲劳扩展。导出了支配半椭圆型表面裂纹尺寸的转移概率密度的FPK方程,给出了裂纹扩展方程在表面和深度两个方向互不耦合情形下的解析解。通过数例详细考察了具有确定性抗裂特性的构件所含半椭圆型表面疲劳裂纹在平稳窄带高斯应力作用下的扩展行为,并有和数字模拟验证方法的有效性。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号