双层非线性耦合反应扩散系统中复杂Turing斑图

采用双层耦合的Brusselator模型, 研究了两个子系统非线性耦合时Turing 模对斑图的影响, 发现两子系统Turing 模的波数比和耦合系数的大小对斑图的形成起着重要作用. 模拟结果表明: 斑图类型随波数比值的增加, 从简单斑图发展到复杂斑图; 非线性耦合项系数在0–0.1时, 系统1中短波模在系统2失稳模的影响下不仅可形成简单六边形、四边形和条纹斑图, 两模共振耦合还可以形成蜂窝六边形、超六边形和复杂的黑眼斑图等超点阵图形, 首次在一定范围内调整控制参量观察到由简单正四边形向超六边形斑图的转化过程; 耦合系数在0.1–1时, 系统1中短波模与系统2失稳模未发生共振耦合仅观察到与系统2相同形状的简单六边形、四边形和条纹斑图. 关键词： Brusselator模型 非线性耦合 Turing模     

气体放电系统中多臂螺旋波的数值分析

采用Purwins的三变量模型, 在二维空间对气体放电系统中多臂螺旋波的形成和转化进行了数值研究. 通过分析方程参数对系统空间的影响, 确定了系统获得稳定螺旋波的参数空间; 得到了斑图由简单静态六边形到螺旋波的演化过程, 分析了螺旋波的形成机制和时空特性; 进一步获得六种不同臂数的多臂螺旋波斑图(例如: 双臂、三臂、四臂、五臂、六臂和七臂螺旋波). 结果表明: 螺旋波斑图出现在图灵-霍普夫(Turing-Hopf)空间, 是Turing模和Hopf模相互竞争、相互作用的结果; 不同臂数的螺旋波波头均在持续地旋转运动, 其运动速度随螺旋波臂数的增加而增大; 随着螺旋波臂数的增加, 其波头的运动形式愈加复杂; 由于受微扰及边界条件的影响, 多臂螺旋波可以向臂数少一的螺旋波发生转变, 数值模拟结果与实验结果符合较好. 关键词： 螺旋波 数值模拟 气体放电     

流动氩气放电系统中条纹斑图形成的实验研究

采用双水电极介质阻挡放电装置, 在大气压下流动氩气中产生了稳定的条纹斑图, 并采用拍照和电学方法对其产生机理进行了研究. 研究发现, 条纹斑图仅出现在外加电压较低的情况下, 在较高电压下放电会过渡到均匀模式. 低电压下的条纹斑图是由于放电丝沿着气流方向定向移动形成的, 该定向移动速度几乎与电压无关, 主要由气体流量决定. 分析发现放电空间中活性粒子的记忆效应对条纹斑图的形成起决定作用. 电学测量发现放电电流和放电的气隙起始电压都随着气流的增加而减小, 本文对这一现象进行了定性解释. 本文结果对斑图动力学研究和介质阻挡放电的工业应用都具有很重要的意义.     

氩气介质阻挡放电不同放电模式的电学特性研究

采用水电极介质阻挡放电装置，在气压为40kPa的氩气中实现了弥散、流光和斑图三种不同 模式的放电，并对其光电特性进行测量.通过测量测试电容上的电压，从而将气隙电压计算 出来，发现随外加电压增加，放电起始时刻不断提前，放电占空比增加；对应放电时刻，气 隙电压减小、输运电荷突增，使得气隙电压和电量波形都远远偏离正弦.气隙电压与输运电 荷成非线性关系.给出了外加电压零点对应的气隙电压随外加电压峰值的变化关系.讨论了壁 电荷在放电中的作用及对气隙电压和电量波形的影响. 关键词： 介质阻挡放电 气隙电压 自组织斑图 输运电荷     

利用高速摄像研究沿面放电斑图的时空演化北大核心CSCD

在氩气柱垂直撞击介质的系统中,随峰值电压的增加,在介质靶上依次产生弥散点、单环和同心三环沿面放电斑图。在这些斑图的演变过程中,每一个电压周期内,正放电数增加,负放电数保持一个。利用高速摄像研究斑图的形成机制,结果表明,每种斑图正负放电都是流光机制,正负沿面放电在时间上叠加形成各种斑图;在每一个电压周期内,第一个正流光形成斑图的中心点,最后一个正流光形成斑图的弥散背景,其他正流光形成斑图的环;每种斑图对应的负流光总是弥散的。通过分析外加电场、残余电荷和空气扩散的影响,定性地讨论了正流光的传播特性。     

介质阻挡放电系统中超四边形斑图形成的实验研究

采用水电极介质阻挡放电装置,在氩气和空气的混合气体放电中,对超四边形斑图的形成进行了实验研究.发现随着外加电压的升高,斑图类型经历了四边形斑图、准超点阵斑图、超四边形斑图、条纹斑图或六边形斑图的演化顺序.对这些斑图进行了傅里叶谱分析,得到了空间模式随电压的变化关系.此外,在外加电压升高的过程中,出现了具有不同空间尺度的两种超四边形斑图,它们满足不同的驻波条件.分析了壁电荷在超四边形斑图形成中的作用.实验测量了斑图类型随气隙间距和外加电压变化的相图以及超四边形斑图随气隙间距和气隙气压变化的相图.测量了击穿电 关键词： 介质阻挡放电 斑图 壁电荷 放电参量     

大气压介质阻挡放电中的自组织斑图结构

采用水作为电极,对大气压介质阻挡放电中的自组织斑图结构进行了研究,观测到了规则的斑图结构(包括准六边形斑图和条带状斑图)和不规则的斑图结构.实验发现斑图中放电丝的密度随着电介质层厚度的增加及放电气隙宽度变大而减小,而随外加电压及频率增大而增大.采用空间相关函数的方法分析了准六边形斑图结构中的放电丝分布与驱动电源电压的关系 关键词： 介质阻挡放电 自组织斑图 放电丝密度 空间相关函数     

介质阻挡放电的电子密度及放电均匀性

建立介质阻挡放电实验系统,研究大气压下外加放电峰值电压和气体组分对气体放电效果的影响.实验研究表明,提高外加放电峰值电压,电子密度明显增加;添加氢气后,观察到明显的潘宁效应,并得出了大气压下获得气体均匀放电的途径.     

氩气/空气介质阻挡放电自组织超六边形斑图实验研究

采用双水电极介质阻挡放电装置,在氩气/空气混合气体放电中,在三种边界条件下得到了一种新型的超六边形斑图.给出了超六边形斑图的傅里叶变换及其不同模强度随旋转角的变化.实验测量了超六边形斑图随空气含量和外加电压变化的相图.研究了超六边形斑图的时空动力学,发现超六边形斑图是由两套子结构嵌套而成.在四边形边界条件下,研究了放电面积的大小对斑图模式选择的影响.发现超四边形斑图的形成受边界条件影响很大,而超六边形斑图则是自组织的结果. 关键词： 介质阻挡放电 超六边形斑图 时空动力学 边界条件     

介质阻挡放电六边形斑图稳定过程的光谱研究

采用发射光谱法,首次研究了等离子体参数及激发状态对介质阻挡放电六边形斑图稳定性的影响。在氩气/空气混合气体的介质阻挡放电中,随着电压的升高,放电丝直径增大,六边形斑图逐渐稳定,同时放电颜色由紫色逐渐变为灰白色,说明其等离子体状态及参数可能发生了变化。测量了六边形斑图放电过程中氮分子谱线和氩原子谱线相对于氩原子763.51 nm的相对强度、分子振动温度和电子激发温度随外加电压的变化。结果发现：氮分子谱线相对强度随电压增加而降低,氩原子谱线相对强度却升高;分子振动温度与电子激发温度均随电压增加而增大。这些现象表明：随着电压增大,电子能量增加。由此,氩原子激发增多,放电丝直径增大,介质表面上沉积的壁电荷面积增大,放电丝之间的相互作用增强,六边形斑图趋于稳定。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.