全光纤光反馈环形腔结构多路激光被动相干合成

提出了基于全光纤光反馈环形腔结构的多路光纤激光相干合成方案,实现了多路激光的被动相干合成。全光纤结构避免了传统孔径拼接输出结构的旁斑能量耗散问题,保证了合成光束的光束质量。开展了实验研究,实现了4路光纤激光的相干锁相输出,获得时域、空域特性均十分稳定的合成光束,合成效率为96.1%,取得较好的合成效果。     

产生钠导引星星群的钠信标激光合/分束技术

研究了脉冲光束的偏振和时序非相干合成技术,通过偏振合束器将两路50 W级500 Hz的589 nm钠信标激光在空间上合为一束光线,成功突破了100 W级μs脉冲全固态钠信标激光输出;利用脉冲激光同步延时器控制两路激光脉冲的时序,使其按先后顺序合成一束脉冲激光,重复频率提升到1 kHz。合束后的激光光束质量M²约为1.41,与单光束的光束质量基本保持一致,光斑抖动性约为40μrad,可满足激光钠导引星自适应光学系统的应用需求。与传统的相干合成方法相比,该偏振和时序非相干合成方案具有结构简单、稳定、效率高的优点,且整个系统无需复杂的相位控制机制,为脉冲激光功率扩展提供了新途径。基于上述技术基础,结合自主提出的精密偏振分光专利技术,在丽江天文台通过一台发射望远镜将四束25 W/束的μs脉冲黄激光发射到钠层,成功产生了四颗钠导引星,这一结果将有助于推动大型地基光学望远镜中多层共轭自适应光学技术的发展。     

亚周期超快光场相干合成技术

随着超快激光脉冲宽度不断变窄,进一步产生单周期乃至亚周期的脉冲面临着巨大的技术挑战。通过脉冲载波包络相位精密控制技术相干合成多路超快光场,不仅是目前超快光学的重要前沿内容,也是实现亚周期脉冲极为有效的方案。结合本课题组近年来在相干合成方面的研究进展,介绍相干合成超快光场的主要技术内容,包括超宽带光谱的产生、色散管理及载波包络相位控制等技术。     

主振荡功率放大器结构光纤激光相干合成系统对谱线需求的实验研究

主振荡功率放大器(MOPA)结构光纤激光相干合成通常被认为需要种子源保持单频输出,而由此引入的非线性效应限制了单链路光纤激光的输出功率。采用宽谱种子源和多波长种子源是抑制非线性效应的有效方式。利用随机并行梯度下降法对三路宽谱光纤放大器和三路多波长光纤放大器相干合成进行了实验研究,取得了理想的相干合成效果。实验结果表明,谱线宽度不是制约MOPA结构相干合成的因素,宽谱放大器和多波长放大器的使用有望使MOPA结构光纤激光相干合成系统获得更高功率的输出。     

基于目标在回路的三路光纤传输激光相干合成实验

实验验证了一种利用目标回光在远场实现相干合成的技术——目标在回路技术.建立了目标在回路相干合成的物理模型,利用可同时调整光程和光束倾斜的自适应光纤光源准直器,同时补偿合成光束间的平移和倾斜相差,实现了基于目标在回路的三路光纤传输激光间相干合成,获得了接近理想情况的合成效果.文章为在实际大气环境中实现多路相干组束的长距离传输提供了参考.     

主振荡功率放大短脉冲光纤激光系统的偏振特性研究

对自行研制的主振荡功率放大结构短脉冲双包层光纤激光系统(2W,30ps)的偏振特性进行了研究.分别研究了种子源激光和经过包层泵浦放大后输出激光在连续工作和脉冲输出情况下的偏振特性,结果表明在不加偏振控制措施情况下,系统输出为椭圆偏振光,偏振度和偏振角都容易受到光纤扰动的影响;在激光腔内加入起偏器后,输出线偏振光,偏振态相对比较稳定,但是偏振角度仍然容易受到光纤扰动的影响.实验证明:经过高功率放大后,输出激光的偏振态稳定性有一定程度的下降,在进行激光相干合成前需进一步加以控制.     

利用全光纤结构Michelson腔实现两路高功率双包层光纤激光器相干合成

Michelson腔技术是实现激光相干合成的有效方案. 利用Michelson腔技术, 实现了全光纤结构下的两路光纤激光器的相干合成, 获得了功率为11.75 W, 效率为95.76%的相干输出. 实验研究了相干合成效率与激光腔长差的关系以及抽运对称性对相干合成效率的影响. 实验表明相干合成效率极易受激光腔长差的影响, 不同腔长差下相干合成效率差异可达18%以上, 且存在最佳腔长差; 抽运对称性对相干合成效率的影响在2%以内.     

主振荡功率放大 (MOPA)短脉冲光纤激光系统的偏振特性研究

对自行研制的MOPA（master oscillator power amplifier）结构短脉冲双包层光纤激光系统（2W,35ps）的偏振特性进行了系统的研究。分别研究了种子源激光和经过包层泵浦放大后输出激光在连续工作和脉冲输出情况下的偏振特性,结果表明在不加偏振控制措施情况下,系统输出为椭圆偏振光,偏振度和偏振角都容易受到光纤扰动的影响;在激光腔内加入起偏器后,输出线偏振光,偏振态相对比较稳定,但是偏振角度仍然容易受到光纤扰动的影响,可以加偏振控制器加以改善。实验证明,经过高功率放大后,输出激光的偏振态稳定性有一定程度的下降,在进行激光相干合成前需进一步加以控制。     

基于并行梯度下降算法模拟高功率固体激光装置的相干合成

 多路光的相干合成是高功率固体激光装置的关键技术之一。基于合成模型,对4组tilt/tip-piston镜采用并行梯度算法,通过模拟计算实现了光束间的位相锁定和相干合成。结果表明有限次算法迭代次数内,相干合成时远场焦斑10 μm半径范围内的强度比约为非相干合成时的4倍。基于高频响应驱动器和对应的高速控制算法将有可能实现高功率固体激光装置多路输出光束间的相干合成。     

不同波形脉冲激光的时域误差对相干合成的影响

相干合成技术是实现高功率、高亮度光纤激光系统的重要技术途径.然而, 脉冲激光阵列中常常存在时域误差,这将影响脉冲激光的相干合成效果. 建立了脉冲激光存在时域误差时的相干合成理论模型,并在不同波形(方波、三角波、正弦波) 的脉冲激光存在时域误差时,对相干合成光束在远场的脉冲波形、峰值功率、 光强分布和桶中功率(PIB)等特性进行了数值计算和对比分析.计算结果表明: 方波脉冲激光相干合成光束的脉冲波形受时域误差影响严重,光强分布和PIB随着时域误差 的增大发生线性变化;三角波脉冲激光相干合成光束的脉冲波形和峰值功率受时域误差 影响严重,光强分布和PIB在时域误差较大时随着时域误差的增大发生较为剧烈的变化; 正弦波脉冲激光相干合成光束具有较好的输出特性,在两路正弦波脉冲激光相干合成中, 将两脉冲之间的时延控制在脉冲持续时间的10%以内,就能取得良好的合成效果.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.