阶梯AlGaN外延新型Al_(0.25)Ga_(0.75)N/GaNHEMTs击穿特性分析

为了优化AlGaN/GaN HEMTs器件表面电场,提高击穿电压,本文首次提出了一种新型阶梯AlGaN/GaN HEMTs结构.新结构利用AlGaN/GaN异质结形成的2DEG浓度随外延AlGaN层厚度降低而减小的规律,通过减薄靠近栅边缘外延的AlGaN层,使沟道2DEG浓度分区,形成栅边缘低浓度2DEG区,低的2DEG使阶梯AlGaN交界出现新的电场峰,新电场峰的出现有效降低了栅边缘的高峰电场,优化了AlGaN/GaN HEMTs器件的表面电场分布,使器件击穿电压从传统结构的446 V,提高到新结构的640 V.为了获得与实际测试结果一致的击穿曲线,本文在GaN缓冲层中设定了一定浓度的受主型缺陷,通过仿真分析验证了国际上外延GaN缓冲层时掺入受主型离子的原因,并通过仿真分析获得了与实际测试结果一致的击穿曲线.     

阶梯AlGaN外延新型Al0.25Ga0.75N/GaNHEMTs器件实验研究

本文报道了作者提出的阶梯AlGaN外延层新型AlGaN/GaN HEMTs结构的实验结果. 实验利用感应耦合等离子体刻蚀(ICP)刻蚀栅边缘的AlGaN外延层, 形成阶梯的AlGaN 外延层结构, 获得浓度分区的沟道2DEG, 使得阶梯AlGaN外延层边缘出现新的电场峰, 有效降低栅边缘的高峰电场, 从而优化了AlGaN/GaN HEMTs器件的表面电场分布. 实验获得了阈值电压-1.5 V的新型AlGaN/GaN HEMTs器件. 经过测试, 同样面积的器件击穿电压从传统结构的67 V提高到新结构的106 V, 提高了58%左右; 脉冲测试下电流崩塌量也比传统结构减少了30%左右, 电流崩塌效应得到了一定的缓解.     

具有N型缓冲层REBULF Super Junction LDMOS

针对功率集成电路对低损耗LDMOS (lateral double-diffused MOSFET)类器件的要求,在N型缓冲层super junction LDMOS (buffered SJ-LDMOS)结构基础上, 提出了一种具有N型缓冲层的REBULF (reduced BULk field) super junction LDMOS结构. 这种结构不但消除了N沟道SJ-LDMOS由于P型衬底带来的衬底辅助耗尽效应问题, 使super junction的N区和P区电荷完全补偿, 而且同时利用REBULF的部分N型缓冲层电场调制效应, 在表面电场分布中引入新的电场峰而使横向表面电场分布均匀, 提高了器件的击穿电压. 通过优化部分N型埋层的位置和参数, 利用仿真软件ISE分析表明, 新型REBULF SJ-LDMOS 的击穿电压较一般LDMOS提高了49%左右, 较文献提出的buffered SJ-LDMOS结构提高了30%左右. 关键词： lateral double-diffused MOSFET super junction 击穿电压 表面电场     

AlGaN/GaN场板结构高电子迁移率晶体管的场板尺寸优化分析

对不同场板尺寸的AlGaN/GaN 场板结构高电子迁移率晶体管进行了研究,建立简化模型分析场板长度对沟道电场分布的影响.结果表明,调整钝化层厚度和场板长度都可以调制沟道电场的分布形状,当场板长度较小时,随着长度的增大器件击穿电压随之增加,而当长度增大到一定程度后器件击穿电压不再增加.通过优化场板长度,器件击穿电压提高了64%,且实验结果与模拟结果相符. 关键词： AlGaN/GaN 击穿电压 场板长度     

新型缓冲层分区电场调制横向双扩散超结功率器件

为了突破传统横向双扩散金属-氧化物-半导体器件(lateral double-diffused MOSFET)击穿电压与比导通电阻的极限关系,本文在缓冲层横向双扩散超结功率器件(super junction LDMOS-SJ LDMOS)结构基础上,提出了具有缓冲层分区新型SJ-LDMOS结构.新结构利用电场调制效应将分区缓冲层产生的电场峰引入超结(super junction)表面而优化了SJ-LDMOS的表面电场分布,缓解了横向LDMOS器件由于受纵向电场影响使横向电场分布不均匀、横向单位耐压量低的问题.利用仿真分析软件ISE分析表明,优化条件下,当缓冲层分区为3时,提出的缓冲层分区SJ-LDMOS表面电场最优,击穿电压达到饱和时较一般LDMOS结构提高了50%左右,较缓冲层SJ-LDMOS结构提高了32%左右,横向单位耐压量达到18.48 V/μm.击穿电压为382 V的缓冲层分区SJ-LDMOS,比导通电阻为25.6 mΩ·cm2,突破了一般LDMOS击穿电压为254 V时比导通电阻为71.8 mΩ·cm2的极限关系.     

具有p-GaN岛状埋层耐压结构的横向AlGaN/GaN高电子迁移率晶体管

GaN基高电子迁移率晶体管(HEMT)相对较低的击穿电压严重限制了其大功率应用.为了进一步改善器件的击穿特性,通过在n-GaN外延缓冲层中引入六个等间距p-GaN岛掩埋缓冲层(PIBL)构成p-n结,提出一种基于p-GaN埋层结构的新型高耐压AlGaN/GaN HEMT器件结构.Sentaurus TCAD仿真结果表明,在关态高漏极电压状态下,p-GaN埋层引入的多个反向p-n结不仅能够有效调制PIBL AlGaN/GaN HEMT的表面电场和体电场分布,而且对于缓冲层泄漏电流有一定的抑制作用,这保证了栅漏间距为10μm的PIBL HEMT能够达到超过1700 V的高击穿电压(BV),是常规结构AlGaN/GaN HEMT击穿电压(580 V)的3倍.同时,PIBL结构AlGaN/GaN HEMT的特征导通电阻仅为1.47 m?·cm~2,因此获得了高达1966 MW·cm~(-2)的品质因数(FOM=BV~2/R_(on,sp)).相比于常规的AlGaN/GaN HEMT,基于新型p-GaN埋岛结构的HEMT器件在保持较低特征导通电阻的同时具有更高的击穿电压,这使得该结构在高功率电力电子器件领域具有很好的应用前景.     

阶梯氧化层新型折叠硅横向双扩散功率器件

为了设计功率集成电路所需的低功耗横向功率器件, 提出了一种具有阶梯氧化层折叠硅横向双扩散金属-氧化物-半导体(step oxide folding LDMOS, SOFLDMOS)新结构. 这种结构将阶梯氧化层覆盖在具有周期分布的折叠硅表面, 利用阶梯氧化层的电场调制效应, 通过在表面电场分布中引入新的电场峰而使表面电场分布均匀, 提高了器件的耐压范围, 解决了文献提出的折叠积累型横向双扩散金属-氧化物-半导体器件击穿电压受限的问题. 通过三维仿真软件ISE分析获得, SOFLDMOS 结构打破了硅的极限关系, 充分利用了电场调制效应、多数载流子积累和硅表面导电区倍增效应, 漏极饱和电流比一般LDMOS 提高3.4倍左右, 可以在62 V左右的反向击穿电压条件下, 获得0.74 mΩ·cm²超低的比导通电阻, 远低于传统LDMOS相同击穿电压下2.0 mΩ·cm²比导通电阻, 为实现低压功率集成电路对低功耗横向功率器件的要求提供了一种可选的方案.     

F离子注入新型Al0．25Ga0．75N／GaNHEMT器件耐压分析

为了缓解AlGaN／GaNhighelectronmobilitytransistors（HEMT）器件n型GaN缓冲层高的泄漏电流,本文提出了具有氟离子注入新型Al0．25Ga0．75N／GaNHEMT器件新结构．首先分析得出n型GaN缓冲层没有受主型陷阱时,器件输出特性为欧姆特性,这样就从理论和仿真方面解释了文献生长GaN缓冲层掺杂Fe,Mg等离子的原因．利用器件输出特性分别分析了栅边缘有和没有低掺杂漏极时,氟离子分别注入源区、栅极区域和漏区的情况,得出当氟离子注入源区时,形成的受主型陷阱能有效俘获源极发射的电子而减小GaN缓冲层的泄漏电流,击穿电压达到262v通过减小GaN缓冲层体泄漏电流,提高器件击穿电压,设计具有一定输出功率新型A1GaN／GaNHEMT提供了科学依据．     

具有部分本征GaN帽层新型AlGaN/GaN高电子迁移率晶体管特性分析

为了优化传统Al GaN/GaN高电子迁移率晶体管(high electron mobility transistors,HEMTs)器件的表面电场,提高击穿电压,本文提出了一种具有部分本征GaN帽层的新型Al GaN/GaN HEMTs器件结构.新型结构通过在Al GaN势垒层顶部、栅电极到漏电极的漂移区之间引入部分本征GaN帽层,由于本征GaN帽层和Al GaN势垒层界面处的极化效应,降低了沟道二维电子气(two dimensional electron gas,2DEG)的浓度,形成了栅边缘低浓度2DEG区域,使得沟道2DEG浓度分区,由均匀分布变为阶梯分布.通过调制沟道2DEG的浓度分布,从而调制了Al GaN/GaN HEMTs器件的表面电场.利用电场调制效应,产生了新的电场峰,且有效降低了栅边缘的高峰电场,Al GaN/GaN HEMTs器件的表面电场分布更加均匀.利用ISE-TCAD软件仿真分析得出:通过设计一定厚度和长度的本征GaN帽层,Al GaN/GaN HEMTs器件的击穿电压从传统结构的427 V提高到新型结构的960 V.由于沟道2DEG浓度减小,沟道电阻增加,使得新型Al GaN/GaN HEMTs器件的最大输出电流减小了9.2%,截止频率几乎保持不变,而最大振荡频率提高了12%.     

具有纵向辅助耗尽衬底层的新型横向双扩散金属氧化物半导体场效应晶体管

为了优化横向双扩散金属氧化物半导体场效应晶体管(lateral double-diffused MOSFET,LDMOS)的击穿特性及器件性能,在传统LDMOS结构的基础上,提出了一种具有纵向辅助耗尽衬底层(assisted depletesubstrate layer,ADSL)的新型LDMOS.新加入的ADSL层使得漏端下方的纵向耗尽区大幅向衬底扩展,从而利用电场调制效应在ADSL层底部引入新的电场峰,使纵向电场得到优化,同时横向表面电场也因为电场调制效应而得到了优化.通过ISE仿真表明,当传统LDMOS与ADSL LDMOS的漂移区长度都是70μm时,击穿电压由462 V增大到897 V,提高了94%左右,并且优值也从0.55 MW/cm~2提升到1.24 MW/cm~2,提升了125%.因此,新结构ADSL LDMOS的器件性能较传统LDMOS有了极大的提升.进一步对ADSL层进行分区掺杂优化,在新结构的基础上,击穿电压在双分区时上升到938 V,三分区时为947 V.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.