老化产生的深能级对GaP纯绿发光二极管发光效率的影响

测量了GaP纯绿发光二极管老化前后的可见和近红外发光光谱,研究了老化产生的深能级的来源及其对二极管发光效率的影响.在老化后的发光光谱中观测到650nm和1260nm发光带,发现1260nm发光带的发光强度随老化时间的增加而增强.实验结果表明老化产生的与磷相关的深能级严重地影响了GaP纯绿LED的发光效率.     

发光二极管用红色荧光粉SrMoO4:Eu3+的制备和发射性质

采用化学共沉淀法制备了适合于紫外、近紫外、蓝光发光二极管(LED)激发的红色荧光粉SrMoO4:Eu3+.研究了样品的晶体结构和发光性质.结果表明:化学共沉淀法合成的SrMoO4:Eu3+荧光粉为四方纯相,其激发光谱包括一个宽带峰和一系列尖峰,峰值位于280nm(宽带峰中心),395nm,465nm,可以被紫外LED和蓝光LED有效激发.在395nm的激发下,测得发射光谱的强发射峰位于613nm,对应Eu3+离子的5D0→7F2跃迁.Eu3+离子掺杂浓度的改变对基质的晶格常数、Eu3+离子在晶体中对称性及发光性能有较大影响.通过对比不同掺杂浓度Eu3+离子的发射谱,发现在SrMoO4基质中Eu3+离子掺杂存在浓度猝灭现象,其最佳掺杂浓度为15%.     

GaN基蓝光发光二极管的波长稳定性研究

尽管GaN基蓝绿光发光二极管（LED）已进入大规模商品化阶段，但其发光波长随注入电流的变化仍是一个尚未解决的关键技术难题.同时，蓝绿光LED电注入发光光谱的半高全宽多为25nm以上.通过优化LED器件材料的生长条件和总应变量，获得了高质量的InGaN/GaN多量子阱LED外延片.由此制作的LED器件在0—120?mA的注入电流下，发光波长变化小于1nm.在20mA的正向电流下，其光谱半高全宽只有18nm，且随注入电流变化较小. 关键词： GaN 发光二极管 波长稳定性     

纳米压印技术制备表面光子晶体LED的研究

利用表面光子晶体能大幅提高发光二极管(LED)的外量子效率, 但如何制备大面积的纳米光子晶体是该研究方向的主要难点之一. 本文基于纳米压印技术在氮化镓基发光二极管(GaN-LED)表面制作孔状二维光子晶体. 通过以金属和聚合物双层掩膜干法刻蚀法, 得到了很好的光子晶体图形转移效果. 最终在LED的p-GaN层表面获得了大面积光子晶体, 周期为450 nm, 纳米孔直径为240 nm. 器件测试结果显示, 有表面光子晶体的LED比没有光子晶体的LED, 光致发光强度峰值提高到了7.2倍.     

用于POF的高性能共振腔发光二极管

提出用AlGaAs材料为n型下DBR,AlGaInP材料为p型上DBR,GaInP/AlGaInP多量子阱为有源区来制备650nm波长的共振腔发光二极管（RCLED）.用传输矩阵法对器件的结构进行了理论设计,并制备了RCLED和普通LED两种结构.测试结果表明,RCLED有更高的发光效率,是普通LED的近1.3倍,当注入电流从3mA增加到30mA时,RCLED的峰值波长只变化了1nm,而普通LED的波长则变化了7nm,且RCLED的光谱半宽窄,远场发散角小. 关键词： 发光二极管 共振腔 金属有机物化学气相淀积     

白光LED用LiSrBO_3∶Sm~(3+)材料的光谱特性(英文)

采用固相法制备了一种新型的白光LED用LiSrBO3∶Sm3+红色发光材料,并研究了材料的光谱特性.材料的激发与发射光谱显示其能够被404nm近紫外光激发,发射599nm红光,很好的符合近紫外光激发下白光LED的需要.研究了Sm3+浓度对材料发射强度的影响,发现Sm3+浓度为3mol%时,强度最大.添加Na+或K+也可提高LiSrBO3∶Sm3+材料的发射强度.     

白光发光二极管的制备技术及主要特性

利用发射波长为470nm的蓝光发光二极管作为基础光源，通过荧光粉转换方法制备白光发光二极管，荧光粉主要采用稀土激活的铝酸盐Y3Al5Ol2：Ce3 (YAG)。在工作电流为15mA条件下，所研制的白光LED的法向光强为2890mcd；色坐标为x=0.29，y=0．33；显色指数为77；流明效率为14．9lm／w。研究制备了不同色温的白光LED，色温范围从2700～8000K，研究了色温与色坐标之间的对应关系。并且与国外同类产品进行比较。部分指标已经超过了国外同类产品水平。     

400nm高性能紫光LED的制作与表征(英文)

利用金属有机物化学气相沉积技术在蓝宝石衬底表面制备了带有p-AlGaN电子阻挡层的400 nm高性能紫光InGaN多量子阱发光二极管。制作了3种紫光LED,分别带有不同p-AlGaN电子阻挡层结构:Al摩尔分数为9%的p-AlGaN电子阻挡层;Al摩尔分数为11%的p-AlGaN电子阻挡层;Al摩尔分数为20%的10对p-AlGaN/GaN超晶格电子阻挡层。带有高浓度Al电子阻挡层的紫光LED的光输出功率高于低浓度Al电子阻挡层的紫光LED。带有10对p-AlGaN/GaN超晶格电子阻挡层的紫光LED的光输出功率获得了极大的提高,在20 mA注入电流时测试得到的光输出功率为21 mW。此外,该LED同时显示了在高注入电流下接近线性的I-L特性曲线和在LED芯片表面均匀的发光强度分布。     

光谱分布可调光源的LED筛选研究

针对LED光谱分布可调光源对LED寿命以及光谱一致性的要求,对可见光和近红外波段的29种LED分别进行200 h的电流加速老化试验,并提出LED光谱一致性筛选算法。老化试验结果表明:峰值波长为385 nm、400 nm 和420 1 nm 3种LED的辐射通量平均衰减分别为24.8 %、10.7 %和25.6 %,不能用于LED光谱分布可调光源;剩余的26种LED的辐射通量平均衰减量均低于3.5 %,可作为光谱分布可调光源的内部光源。LED光谱一致性筛选算法以LED光谱数据为基础,计算同类LED间的相对光谱偏差,26种LED的相对光谱偏差均小于4.5 %,保证了所筛选出LED的光谱一致性。     

基于外延层转移的超薄垂直结构深紫外LED

AlGaN基深紫外(Deep ultraviolet,DUV)发光二极管(Light-emitting diode,LED)可用于杀菌、水体净化、光疗、固化、传感和非视距通信等场合,在生物、环境、工业、医疗和军事等领域具有广阔的应用前景。针对现阶段DUV LED外量子效率较低的问题,本文提出了一种超薄垂直结构的DUV LED方案。该方案基于蓝宝石-硅晶圆键合和物理减薄工艺实现了高质量DUV LED外延层从蓝宝石衬底到高导热硅基板的转移,并采用转移后亚微米厚度的超薄外延层制备出垂直结构的AlGaN DUV LED。器件的出光面在减薄工艺后无需特殊的化学处理便可实现纳米级的粗化,配合超薄外延层结构具备显著的失谐微腔效应,有助于破坏高阶波导模式,从而增加TM波的出光并提升器件的出光效率。测试表明,转移后的外延层厚度约为710 nm,制备出的DUV LED发光光谱峰值波长约为271 nm。该垂直结构DUV LED制备方案为实现高效DUV光源提供了可行路径。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.