Differential Pulse Polarography for a First‐Order EC Process and Its Diagnostic Parameters

Theoretical expressions for differential pulse polarography (DPP) for a reversible electron transfer coupled with an irreversible follow‐up first‐order chemical reaction (E_rC_i) is derived approximately. The peaks as given by the current expressions are analyzed in terms of several parameters such as a ratio of anodic‐to‐cathodic peak‐currents (i_p^a/i_p^c), a separation of peak‐potentials (E_p^c?E_p^a), and a ratio of anodic‐to‐cathodic half‐peak‐widths (W_1/2^a/W_1/2^c) in order to characterize the E_rC_i process and distinguish it from other types of electrode processes. The anodic peak is found to be more susceptible to the post kinetics than the cathodic peak. The new parameter of W_1/2^a/W_1/2^c ratio is much more sensitive to the post kinetics than the peak separation (E_p^c?E_p^a). The peak current ratio (i_p^a/i_p^c) and the peak‐width ratio (W_1/2^a/W_1/2^c) have comparable sensitivities to the kinetics. Hence, W_1/2^a/W_1/2^c ratio is a better diagnostic parameters than (E_p^c?E_p^a) which has a poor sensitivity. This phenomenon is different from cyclic voltammetry (CV) in which E_p^c?E_p^a is as sensitive as i_p^a/i_p^c. The new criteria for EC with DPV is tested and successfully applied to several Co(III) complex systems, including coenzyme B₁₂. The homogeneous rate constant (k) for the follow‐up step is estimated from the measurements of the experimental values of the parameters. The present treatment is valid quantitatively at lower values of k, yielding relatively larger errors for higher k values (k>10 s^?1).     

Voltammetry of resazurin at a mercury electrode

Electrochemical behavior of resazurin on HMDE in Britton-Robinson (B-R) buffers (pH 2.0–10.0) was studied using the square-wave voltammetry (SWV), square-wave adsorptive stripping voltammetry (SWAdSV), and cyclic voltammetry (CV) techniques. The voltammogram of resazurin in B-R buffer at pH < 4.0 exhibited two cathodic reduction peaks. The voltammetric peaks were obtained at −0.144 V (reversible) and −1.250 V (irreversible) at pH 3.2, and correspond to the reduction of resorufin to dihydroresorufin and to the catalytic hydrogen wave, respectively. At pH > 4.0, a new irreversible cathodic reduction peak, assigned to the protonation of N-oxide on the phenoxazin ring, was observed. Electrochemical parameters (I _p/E _p, I _p/v, I _p/pH, I _p/t _acc) of the compound were determined. From the voltammetric data, electrochemical reduction mechanisms for all peaks have been suggested. Maximum peak current for the reversible peak was obtained at pH 4.1. A linear relationship between the current and concentration was determined, and also the lowest detection limit was found as 3.25 × 10⁻⁸ mol L⁻¹ and 1.98 × 10⁻¹⁰ mol L⁻¹ for SWV and SWAdSV, respectively.     

Studies on photo-electro-chemical catalytic degradation of acid scarlet 3R dye

The photocatalytic oxidation of poisonous or nonbiodegradable organic pollutants in wastewater has been the focus of numerous environmental investiga- tions in recent years. Selecting excellent-performance photocatalytic material is very important in thes…     

Quasi-reversible two-electron reduction of oxygen at gold electrodes modified with a self-assembled submonolayer of cysteine

The electrochemical reduction of molecular oxygen (O₂) has been performed at gold electrodes modified with a submonolayer of a self-assembly (sub-SAM/Au) of a thiol compound (typically cysteine (CYST)) in O₂-saturated 0.5 M KOH. At bare gold electrode O₂ reduction reaction proceeds irreversibly, while this reaction is totally hindered at gold electrodes with a compact structure of CYST over its surface. The partial reductive desorption of the compact CYST monolayer was achieved by controlling the potential of the CYST/Au electrode, leading to the formation of a submonolayer coverage of the thiol compound over the Au electrode surface (sub-SAM/Au), at which the CYST molecules selectively block the Au(1 0 0) and Au(1 1 0) fractions (the so-called rough domains) of the polycrystalline Au while the Au(1 1 1) component (the so-called smooth domains) remains bare (i.e., uncovered with CYST). This sub-SAM/Au electrode extraordinarily exhibits a quasi-reversible two-electron reduction of molecular oxygen (O₂) in alkaline medium with a peak separation (ΔE_p) between the cathodic and anodic peak potentials (E_p^c,E_p^a) of about 60 mV. The ratio of the anodic current to the cathodic one is close to unity. The formal potential (E^o′) of this reaction is found to equal −150 mV vs. Ag/AgCl/KCl(sat.).     

Thin films of Pd and Pd–1% MWCNT as new electrocatalysts for oxidation of phenol in acid medium

Thin films of pure Pd and composite of Pd and 1% multiwalled carbon nanotube have been obtained on glassy carbon electrodes by borohydride reduction method and investigated as electrocatalysts for the oxidation of phenol in acid medium at 25 °C, using cyclic voltammetry (CV), chronopotentiometry, and high-performance liquid chromatography. The CV study showed that both the electrocatalysts are quite stable and active for the phenol oxidation in acid medium. Further, these electrodes do not seem to undergo deactivation due to intermediates and products formed during the phenol oxidation. With the increase in phenol concentration from 2 to 25 mM, the peak current (I _p) increases initially, reaches maximum at about 15 mM, and tends to decrease thereafter. The peak potential (E _p) value was found to be practically unchanged with phenol concentration. The rate for phenol oxidation (I _p) at the surface of both the electrocatalysts increased with the decrease in pH of the reaction mixture. The electrocatalytic activity of the composite electrode was, however, higher than that of pure Pd under similar experimental conditions. Benzoquinone and hydroquinone were identified as the major phenol degradation intermediate products.     

Voltammetric study on interaction of cysteine with type I-collagen in the aqueous medium

Interaction of cysteine with type I-collagen from bovine achilles tendon in the aqueous solutions has been examined using square wave voltammetry (SWV) and cyclic voltammetry (CV) techniques. In the absence of cysteine, type I-collagen gives a reversible peak at ?0.114 V in Britton-Robinson (B-R) buffer (pH 4.0). The electrochemical parameters (I _p/f, E _p/f, E _p/pH, I _p/pH, I _p/v, I _p/v^1/2) of type I-collagen have been also studied. In addition, it has been determined that there is a linear relationship between current and concentration of type I-collagen. On the other hand, cysteine exhibits a reversible peak at ?0.383 V due to the reduction of mercurous cysteine thiolate. By using a hanging mercury drop electrode in aqueous solutions, SWV and CV voltammograms obtained for type I-collagen in the presence of cysteine indicate that there is an interaction between type I-collagen and cysteine. In the presence of cysteine, peak current of type I-collagen decreases and a new peak is observed at ?0.121 V for cysteine which is bonded to type I-collagen.     

Investigation of the electrochemical behaviour of lead dioxide in aqueous sulfuric acid solutions by using the in situ EQCM technique

The charge-discharge characteristics and the aging mechanism of PbO₂ layers in contact with sulfuric acid solutions of different concentrations (1.5–5.0 M) were studied by using combined cyclic voltammetry and electrochemical quartz crystal microbalance (EQCM) techniques. For this purpose, thick lead dioxide layers were electrodeposited on gold substrate from aqueous solutions of Pb(NO₃)₂ dissolved in nitric acid. Based on the electrochemical and the mass change responses, it was found that in more concentrated solutions of H₂SO₄, the main reduction reaction was the transformation of lead dioxide to lead sulfate. However, in less concentrated sulfuric acid media, the transformation of lead dioxide to lead(II) ion became the main reaction. These Pb²⁺ ions transformed into lead sulfate crystals later by a chemical reaction. Because the electrochemical oxidation of lead sulfate is less favourable in sulfuric acid medium of higher concentrations, thus, PbO₂ layers cannot be tested by continuous cyclization, which is necessary to study their aging parameters. Therefore, a delay step before each cyclic voltammogram was applied while the non-conductive lead sulfate dissolves or alternatively, by applying a pre-oxidation step prior to each cyclic voltammetry experiment to produce electrochemically significant amount of lead dioxide which can be reduced during the following negative potential sweep.

     

Electrochemical Behavior of a Glassy Carbon Electrode Chemically Modified with Nickel Pentacyanonitrosylferrate in Presence of Sulfur Compounds

The glassy carbon electrode was modified with a nickel pentacyanonitrosylferrate film by electrodeposition of Ni and subsequent derivatization with NaPCNF. The film was characterized by XPS and electrochemical methods. Cyclic voltammetry of the NiPCNF onto the GC shows a redox couple (Fe^III/Fe^II) with E°′ of 538 mV (I_pa/I_pc around 1) and ΔE_p of 93 mV in 0.5 mol L^?1 KNO₃, with a diffusion‐controlled process. There was a decrease of anodic peak currents of the film in the presence of sulfide and 2‐propanethiol due to a precipitation reaction on the film surface by nucleophilic attack.     

Voltammetric determination of quercetin at a multi-walled carbon nanotubes paste electrode

Quercetin can effectively accumulate at multi-walled carbon nanotubes-paraffin oil paste electrodes (CNTPE) and cause a sensitive anodic peak at around 0.32 V (vs. SCE) in a 0.10 M phosphate buffer solution (pH = 4.0). Under optimized conditions, the anodic peak current is linear to quercetin concentration in the ranges of 2.0 × 10^− 9−1.0 × 10^− 7 M and 1.0 × 10^− 7−2.0 × 10^− 5 M, and the regression equations are i_p (μA) = 0.0017 + 0.928c (μM, r = 0.999) and i_p (μA) = 0.183 + 0.0731c (μM, r = 0.995), respectively. This paste electrode can be regenerated by repetitively cycling in a blank solution for about 2 min. A 1.0 × 10^− 6 M quercetin solution is measured for 10 times using the same electrode regenerated after every determination, and the relative standard deviation of the peak current is 1.7%. The method has been applied to the determination of quercetin in hydrolysate product of rutin and the recovery is 99.2–102.6%. In comparison with graphite paste electrode, carbon nanotubes-nujol paste electrode and carbon nanotubes casting film modified glassy carbon electrode, the CNTPE gives higher ratio of signal to background current and better defined voltammetric peak.     

The influence of different variables on the electrochemical behavior of mild steel in circulating cooling water containing aggressive anionic species

Cyclic voltammetric, potentiodynamic anodic polarization and current–time transient studies were carried out on mild steel in circulating cooling water containing Cl⁻ and SO₄⁻² ions under the effect of different variables such as coolant flow, the availability of oxygen, cooling system temperature, and cooling system pH. The anodic excursion span of mild steel in cooling corrosive solution was characterized by the occurrence of a well-defined anodic peak (A1), while the reverse sweep was characterized by the appearance of two cathodic peaks (C1 and C2). The presence of Cl⁻ and SO₄⁻² ions in cooling water enhance the active dissolution of mild steel and tend to breakdown the passive film and induce pitting attack. The data reveal that increasing flow rate and temperature of cooling solution enhances the anodic peak current density (j _A1) and shifts the pitting potential (E _pit) towards more active values. It is seen that the peak current density of the anodic peak A1 increases and the pitting potential (E _pit) displaced in the noble direction in the aerated solution compared that in de-aerated solution. The pitting corrosion of mild steel by Cl⁻ and SO₄⁻² ions initiates more readily in acidic medium (pH 2.0). It was found that the incubation time (t _i) increase and in turn the pitting corrosion decrease in the order: pH 10 > pH 6.8 > pH 2.0.     

Kinetics of electrode processes on a bismuth electrode in acid solutions containing thiourea and formamidine disulphide

A study of the mechanism by which bismuth is electrodissolved in an aqueous solution of thiourea on the background of H₂SO₄ demonstrated that, in the thiourea concentration range 0.001 M < c < 0.5 M, a current oscillation is observed in cyclic voltammograms at E ≈ 0.4–0.3 V when the potential is swept from the anodic to the cathodic region. This oscillation is due to the loosening of the passivating film formed in the anodic process. It is shown that thiourea is not oxidized to formamidine disulphide at the bismuth electrode. thiourea and formamidine disulphide have mutually opposite effects on the height of the cathodic peak: the peak current falls with increasing thiourea concentration and grows with increasing formamidine disulphide concentration. According to the results of an X-ray fl uorescence analysis, sulfur is formed on the bismuth electrode upon its prolonged polarization of in a 0.5 M solution of thiourea. An explanation is provided for the experimental facts observed in the study.     

Effect of acetic acid on CO2 corrosion of carbon steel in NaCl solution

Potentiodynamic sweep and electrochemical impedance spectroscopy measurements were applied to investigate the effects of both temperature and acetic acid (HAc) on the anodic and cathodic reactions in CO₂ corrosion of P110 steel in 3.5% NaCl solution. The temperatures were controlled at 30 and 60 °C. The concentrations of HAc were controlled at 0, 1000, 3000 and 5000 ppm. In this work, the corrosion parameters of polarization curves, such as corrosion potential (E_corr), corrosion current density (i_corr), and anodic and cathodic branch slopes (b_a and b_c), are presented and discussed in detail. In addition, the equivalent circuit models and ZsimpWin software were utilized to discuss the Nyquist plots. The plots showed that the E_corr values shifted in the positive direction as the HAc concentration increased. The i_corr values increased with the increase in HAc concentration, indicating that HAc could accelerate the corrosion. The impedance spectra measured at 30 and 60 °C have different time constants and characterization. The coverage fraction θ and the thickness L of corrosion film are two most important controlled variables that influence and control the CO₂ corrosion mechanisms. Copyright © 2010 John Wiley & Sons, Ltd.     

Experimental study of a closed system in the chlorine dioxide–iodine–ethyl acetoacetate–sulfuric acid oscillation reaction by UV–vis and online FTIR spectrophotometric methods

The appearance of oscillations depends critically on the pH for a closed system of ClO₂–I₂–ethyl acetoacetate in the absence of sulfuric acid, and was investigated by determining the absorbance of I₃⁻ with reaction time at 280 nm. The pH should be 2.2–3.8. The initial concentration of ethyl acetoacetate, chlorine dioxide, iodine, and sulfuric acid has great influence on the oscillation at 581 nm for I₃⁻–starch complex (SI₃⁻). The oscillation occurs as long as the reactants are mixed at 280 nm. There is no pre-oscillatory period. However, at 581 nm, there is an induction period. The curve’s shape at 581 nm is very different from that at 280 nm. The oscillation becomes more obvious by adding starch at 581 nm for I₃⁻–starch complex (SI₃⁻) than that observed without adding starch at 280 nm. The oscillation curve is more regular and smooth by adding starch at 581 nm than that without adding starch at 280 nm. The amplitude and the number of oscillations are associated with the initial concentration of reactants. The higher the initial concentration of ethyl acetoacetate, the bigger the amplitude. Also, the number of oscillations becomes small. An opposite influence exists for chlorine dioxide and iodine. The higher the initial concentration of sulfuric acid, the bigger the amplitude. Also, the number of oscillations becomes large. The equations for the triiodide ion reaction rate changing with reaction time and the initial concentrations on the oscillation stage were obtained. The intermediates were detected by the online FTIR analysis. Based upon the experimental data in this work and in the literature, a plausible reaction mechanism was proposed for the oscillation reaction.     

Voltammetric determination of pyrocatechol at a mechanically renewed electrode made of a graphite-epoxy composite

The reversibility of a two-electron pyrocatechol/o-benzoquinone system (ΔE _p = 28 ± 1 mV) is found by cyclic voltammetry at a mechanically renewed electrode from a graphite-epoxy composite. The closeness of the found and theoretical values of ΔE _p indicates the high electrochemical activity of the graphite-epoxy composite electrode renewed in situ by cutting a thin surface layer. The potentials of pyrocatechol anodic and cathodic peaks are proportional to E ₀ ± 0.059pH in the pH range of 1–9. The pyrocatechol anodic and cathodic peak currents remain linear functions of pyrocatechol concentration in the concentration range from 0.01 to 0.08 and from 0.08 to 0.9 g/L, respectively. A procedure for the voltammetric determination of pyrocatechol in its individual solutions and in the presence of hydroquinone is proposed. Good precision and the absence of a systematic error in the determination of pyrocatechol by measuring its cathodic peak are demonstrated.     

A study on the electronic effect of <Emphasis Type="Italic">para</Emphasis> substituents in the aryloxy ring of the hydrazone ligands on the vanadium centre in a family of mixed-ligand [V<Superscript>V</Superscript>O(ONO)(OO)] complexes

[V^IVO(acac)₂] reacts with the methanolic solutions of tridentate dibasic ONO donor hydrazone ligands derived from the condensation of benzoyl hydrazine with either 2-hydroxyacetophenone (H₂L¹) or its para-substituted derivatives (H₂L^2–4) (general abbreviation H₂L), in the presence of vanillin (Hvan) in equimolar ratio under aerobic conditions generating the mixed-ligand oxovanadium(V) complexes of the type [V^VO(L)(van)], (1)–(4) in good yield. All the complexes are diamagnetic and exhibit only ligand-to-metal charge transfer (l.m.c.t.) band near 510 nm in addition to intra-ligand (π → π*) transition band near 330 nm in CH₂Cl₂ solution. ¹H-n.m.r. spectra of the complexes in CDCl₃ solution indicate the presence of two isomeric forms [(1A), (1B); (2A), (2B); (3A), (3B) and (4A), (4B)] in different ratios, which is explained by the interchange of the two binding sites of van⁻ motif between its coordinated equatorial and axial positions. Complexes display two quasi-reversible one electron reduction peaks near +0.10 V and near +0.30 V versus s.c.e. in CH₂Cl₂ solution which are attributed to the successive reduction of V^V→ V^IV and the V^IV→ V^III motifs, respectively. λ_max (for l.m.c.t. transition), and the two reduction potential values (E _1/2)^I (average of the first step anodic and first step cathodic peak potentials) and (E _1/2)^II (average of the second step anodic and second step cathodic peak potentials) of the complexes, are found to be linearly related to the Hammett constants (σ) of the substituents in the aryloxy ring of the hydrazone ligands. λ_max, (E _1/2)^I and (E _1/2)^II values show large dependence: dλ_max/dσ = 37.29 nm, d(E _1/2)^I/dσ = 0.21 V and d(E _1/2)^II/dσ = 0.21 V, respectively, on σ.     

Chemical Speciation of Antimony(III and V) in Water by Adsorptive Cathodic Stripping Voltammetry Using the 4‐(2‐Thiazolylazo) – Resorcinol

A simple adsorptive cathodic stripping voltammetry method has been developed for antimony (III and V) speciation using 4‐(2‐thiazolylazo) – resorcinol (TAR). The methodology involves controlled preconcentration at pH 5, during which antimony(III) – TAR complex is adsorbed onto a hanging mercury drop electrode followed by measuring the cathodic peak current (I_p,c) at ?0.39 V versus Ag/AgCl electrode. The plot of I_p,c versus antimony(III) concentration was linear in the range 1.35×10^?9–9.53×10^?8 mol L^?1.The LOD and LOQ for Sb(III) were found 4.06×10^?10 and 1.35×10^?9 mol L^?1, respectively. Antimony(V) species after reduction to antimony(III) with Na₂SO₃ were also determined. Analysis of antimony in environment water samples was applied satisfactorily.     

Direct electrochemistry of myoglobin in a layer-by-layer film on an ionic liquid modified electrode containing CeO2 nanoparticles and hyaluronic acid

We describe an ionic liquid modified electrode (CPE-IL) for sensing hydrogen peroxide (HP) that was modified by the layer-by-layer technique with myoglobin (Mb). In addition, the surface of the electrode was modified with CeO₂ nanoparticles (nano-CeO₂) and hyaluronic acid. UV-vis and FTIR spectroscopy confirmed that Mb retains its native structure in the composite film. Scanning electron microscopy showed that the nano-CeO₂ closely interact with Mb to form an inhomogeneously distributed film. Cyclic voltammetry reveals a pair of quasi-reversible redox peaks of Mb, with the cathodic peak at ?0.357?V and the anodic peak at ?0.269?V. The peak separation (??E _p) and the formal potential (E ^0??) are 88?mV and ?0.313?V (vs. Ag/AgCl), respectively. The Mb immobilized in the modified electrode displays an excellent electrocatalytic activity towards HP in the 0.6 to 78.0???M concentration range. The limit of detection is 50?nM (S/N?=?3), and then the Michaelis-Menten constant is 71.8???M. We believe that such a composite film has potential to further investigate other redox proteins and in the fabrication of third-generation biosensors.

Sensitive and Profitable Electrochemical Detection of Uric Acid in the Presence of Dopamine with a Novel Carbon Paste Electrode Decorated with a Copper(II) Complex

A new microcomposite with copper(II) complex and carbon paste (Cu_C/CPE) was developed to determine the uric acid (UA) content in the presence of dopamine (DP) and was characterized via cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and energy dispersive spectroscopy (EDS). The results showed high selectivity for UA compared with DP because the anodic peak currents for DP were near those of a CPE without Cu_c and were considerably increased for UA. The UA and DP increases were 86.9 % and 14.3 %, respectively, according to CV and 96.6 % and 25.5 %, respectively, according to square wave voltammetry (SWV) with the Cu_C/CPE. Moreover, the anodic peak separation for UA and DP was 0.17 V. With optimal parameters (pH, 3.3; adsorption time(t_ADS), 30 s;adsorption potential (E_ADS)_, 0.10 V), the anodic peak currents for UA were proportional to concentrations between 1.6 and 14.4 μmol L^?1 using standard solutions with UA concentrations ranging from 8.0–40.5 μmol L^?1 and real samples. The UA detection limit was 0.13 μmol L^?1. The new sensor was used to determine the UA contentin human urine samples, and the method was checked with a urine chemistry control from Bio‐Rad based on human urine spiked with quantities of UA and showed a recovery between 84 % and 106 % at concentrations below 10.0 μmol L^?1.     

Investigation of the electrode reaction of EDTA and other complexanes at the lead dioxide electrode in aqueous solutions

Summary By using an electrodeposited lead dioxide electrode as an indicator electrode, the electrode reaction of ethylenediaminetetraacetic acid (EDTA) and other complexanes was investigated in unbuffered solution covering a pH range of about 2–12. Well-defined anodic and cathodic peaks, the heights of which increase with EDTA concentration, were observed. In an anodic single-sweep process, one anodic pre-peak appeared only at a pH higher than 4. It was found that in the cathodic process lead dioxide on the electrode is reduced to lead ion which reacts with EDTA to form the complex and in the anodic process the lead complex is oxidized again and deposited onto the electrode as lead dioxide. The height of the anodic and cathodic peaks is directly proportional to the EDTA concentration. The lead dioxide electrode seems to be useful for determining a chelating agent such as the EDTA-type complexanes.

---

Untersuchung der Elektrodenreaktion von EDTA und anderen Komplexanen in wäßriger Lösung an der Bleidioxidelektrode

Zusammenfassung Mit Hilfe der elektrolytisch belegten PbO₂-Elektrode wurde die Elektrodenreaktion von EDTA (sowie von IDA, NTA und DTPA) in ungepufferter Lösung im pH-Bereich 2–12 untersucht. Gut ausgebildete anodische und kathodische Peaks wurden beobachtet, deren Höhe mit der EDTA-Konzentration zunimmt. Im anodischen single-sweep-Prozeß erschien nur ein anodischer Vorpeak bei pH>4. Es wurde festgestellt, daß bei dem kathodischen Vorgang PbO₂ an der Elektrode zu Pb-Ion reduziert wird, das mit EDTA unter Komplexbildung reagiert, während an der Anode der Pb-Komplex wieder oxidiert und PbO₂ abgeschieden wird. Die Peakhöhen sind der EDTA-Konzentration direkt proportional. Die PbO₂-Elektrode erscheint daher von Nutzen für die Bestimmung von Komplexanen vom Typ des EDTA.

     

Voltammetry of immobilized cytochrome c on novel binary self-assembled monolayers of thioctic acid and thioctic amide modified gold electrodes

Horse heart cytochrome c (cyt c) was adsorbed on the binary self-assembled monolayers (SAMs) composed of thioctic acid (T-COOH) and thioctic amide (T-NH₂) at gold electrodes via electrostatic interaction. The cyt c adsorbed on the modified gold electrode exhibited well-defined reversible electrochemical behavior in 10 mM phosphate buffer solution (PBS, pH 7.0). The surface concentration (Γ) of electroactive species, cyt c, on the binary SAMs was higher than that in single-component SAMs of T-COOH, and reached a maximum value of 9.2 × 10⁻¹² mol cm⁻² when the ratio of T-COOH to T-NH₂ in adsorption solution was of 3:2, and the formal potential (E^0′=(E_pa+E_pc)/2) of cyt c was −0.032 V (vs. Ag|AgCl (3 M NaCl)) in a 10 mM PBS. The interaction between cyt c and the binary SAMs made the E^0′ shift negatively when compared with that of cyt c in solution (+0.258 V vs. NHE, i.e., +0.058 V vs. Ag|AgCl (3 M NaCl)). The fractional coverage of bound cyt c was a 0.64 theoretical monolayer. The standard electron transfer rate constant of cyt c immobilized on the binary SAMs was also higher than that on single-component SAMs of T-COOH, and the maximum value of 15.8 ± 0.6 s⁻¹ was obtained when the ratio of T-COOH to T-NH₂ in adsorption solution was at 3:2. The results suggest that the electrode modified with the binary SAMs functions better than the electrode modified with single-component SAMs of T-COOH.