NOVEL RED LIGHT-EMITTING POLYMERS BASED ON 2,7-CARBAZOLE AND THIOPHENE DERIVATIVES

A series of conjugated copolymers derived from 9-ethylhexyl-2,7-carbazole(Cz)and 4,7-di(4-hexylthien-2-yl)- 2,1,3-benzothiadiazole(DHTBT)was synthesized by Suzuki polycondensation.The photo-and electro-luminescent properties of these polymers were investigated.Efficient energy transfer from the Cz segment to the DHTBT unit occurs even if the DHTBT content as low as 1 mol%.PL emission was red-shifted significantly from 645 nm to 700 nm with the increase in DHTBT content by 1-50 mol%.PL efficiencies decrea...     

超薄层在白色有机电致发光器件中的应用

以DCJTB为掺杂剂, 以BCP为空穴阻挡层, 研究了两种结构的有机电致发光器件ITO/NPB/BCP/Alq3:DCJTB/Alq3/Al(结构A)和ITO/NPB/BCP/Alq3/Alq3:DCJTB/Alq3/Al(结构B)的电致发光光谱. 实验结果显示, 在结构A器件的电致发光光谱中, 绿光的相对发光强度较弱,增加Alq3层的厚度对绿光的相对发光强度的影响也很小; 而在结构B器件的电致发光光谱中, BCP层与掺杂层(Alq3:DCJTB)之间的Alq3薄层对绿光的相对发光强度影响显著, 用很薄的Alq3层就可以得到强的绿光发射. 进一步改变器件结构, 利用有机超薄层就可以得到稳定的白光器件ITO/NPB(50 nm)/BCP(3 nm)/Alq3(3 nm)/Alq3:DCJTB(1%(w))(5 nm)/Alq3(7 nm)/Al. 随着电压的增加(14-18 V), 该器件的色坐标基本保持在(0.33, 0.37)处不动; 在432 mA·cm-2的电流密度下, 该器件的发光亮度可达11521 cd·m-2.     

新型基于3,6-咔唑与噻吩衍生物的红光聚合物的合成与性能研究

用Suzuki偶合反应制备了一系列N-(2-乙基己基)-3,6-咔唑(Cz)与4,7-二(4-己基噻吩)-2,1,3-苯并噻二唑(DHTBT)的共聚物, 研究该类聚合物的电化学、光学和电致发光性能. 在薄膜状态下, 即使DHTBT含量为1%的聚合物也发生了从Cz链段到DHTBT单元的有效的能量转移. 光致发光光谱随着DHTBT含量的增加, 从645 nm红移至690 nm. PCzDHTBT1获得了71%的薄膜光致发光效率. 以该类聚合物为发光层的器件的EL光谱也随着DHTBT含量的增加从635 nm红移至680 nm. 由PCzDHTBT15制作的结构为ITO/PEDOT:PSS/polymer/Ba/Al的器件得到了0.61%的外量子效率.     

新型水溶性萘啶基荧光材料的制备及性能研究

本文制备得到一种新型萘啶基的水溶性光致发光聚合物:聚丙烯酸(PAA)-2-苄氨基-7-甲基-1,8-萘啶,PAA₅-PAMN₂(PAMN是2-phenmethy-lamino-7-methyl-1,8-naphthyridine的缩写),经光谱分析和密度泛函理论计算,研究了化合物的结构和组成.这种聚合物在酸性和碱性条件下呈现最大的吸收波长分别为364和342 nm.Zn(OAc)₂的加入致使PAA₅-PAMN₂水溶液的荧光猝灭,而当OAc^-改变为NO₃^-时,在荧光强度不断降低的同时,由于NO₃^-离子的配位使最大发射波长从410 nm蓝移到400 nm.Na⁺+离子对其没有明显的荧光猝灭效应.     

Nearly monochromatic red electroluminescence from a nonconjugated polymer containing carbazole segments and phenanthroline [Eu(β‐diketonate)3] moieties

A novel nonconjugated copolymer (PVKEu) with carbazole segments and phenanthroline [Eu(β‐diketonate)₃] moieties was synthesized via free radical copolymerization, and characterized by FTIR, ¹H NMR spectroscopy, GPC, ICP, and elemental analysis. The copolymer exhibited good solubility, as well as good thermal stability and high glass transition temperature. The photoluminescence (PL) of this polymer in solution and in solid film has been studied. A multi‐layer device with the configuration of ITO/PEDOT: PSS (40 nm)/PVKEu (70 nm)/BCP (15 nm)/AlQ₃ (30 nm)/LiF/Al exhibited nearly monochromatic red emission at 615 nm and voltage‐independent spectral stability. Our results suggest that enhancing the ligand‐mediated energy transfer between the matrix polymer and europium complex is a potential method to improve the electroluminescence performance of the Eu‐chelated polymers. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 210–221, 2009     

基于萘二甲酸及邻菲咯啉衍生物的铅配位聚合物的合成及结构

利用水热合成法得到了二维配位聚合物[Pb2(L)(1,4-NDC)2].0.5H2O(1),并对该化合物进行了元素分析、红外、热重和单晶X-射线表征,其中L为邻菲咯啉衍生物配体(1-(1H-imidazo[4,5-f][1,10]phenanthrolin-2-yl)naphthalen-2-ol),1,4-NDC为1,4-萘二甲酸根。该化合物属于三斜晶系,空间群P1,晶胞参数a=0.95078(6)nm,b=1.26511(8)nm,c=1.78591(12)nm,α=78.441(2)°,β=78.620(1)°,γ=77.124(1)°,V=2.025 3(2)nm3。该化合物为二维层状结构,层与层之间又进一步地通过π-π相互作用形成二维双层超分子结构。     

Metal-free phthalocyanine single crystal: Solvothermal synthesis and near-infrared electroluminescence

A metal-free purple H₂Pc single crystal was synthesized by a facile solvothermal method, and its solubility and near-infrared (NIR) optical properties were also investigated due to its potential applications as a light-emitting layer for OLEDs. The H₂Pc single crystal is insoluble in 1-chlorine naphthalene and other organic solvents. It gives a wide absorption in the range from 620 nm to 679 nm and a wide emission in near 922 nm. As an active light-emitting layer, H₂Pc was employed to fabricate electroluminescent (EL) devices with a structure of ITO/NPB (30 nm)/Alq₃:H₂Pc (30 nm)/BCP (20 nm)/Alq₃ (20 nm)/Al. The emission center is at 936 nm when the H₂Pc doping concentration is 20 wt%. The doping concentration strongly governs the emission intensity. When doping concentration decreases from 10 wt% to 1 wt%, the emission intensity remarkably fades, and simultaneously the emission center undergoes a blue shift.     

Synthesis of an electroluminescent polymer and its non‐doped light‐emitting diodes with stable green emission

An electroluminescent polymer was synthesized by Wittig condensation and characterized by the measurements of ¹H‐NMR, IR, gel permeation chromatography (GPC), UV–Vis, PL, and cyclic voltammetry (CV). The polymer can be dissolved in common organic solvents such as tetrahydrofuran (THF), chloroform, and dichloromethane. The electroluminescent investigation showed that the non‐doped devices with a double‐layer configuration (ITO/PEDOT:PSS/Polymer/Mg:Ag) have a stable green emission property. The maximum luminance of the annealed device reaches 2317 cd/m². The emission maximum and the CIE 1931 coordinate values are respectively stabilized at 552 nm and near (x, y) = (0.43, 0.55) with different voltages. Copyright © 2008 John Wiley & Sons, Ltd.     

二维层状磺酸银(Ⅰ)配位聚合物的合成、晶体结构与性能研究

本文合成了1个二维层状磺酸银配位聚合物[Ag2(HL)(MeCN)]n,(H3L=2-羟基-3-羧基-5-溴苯磺酸),并且进行了元素分析、红外、热重、荧光、粉末及单晶X射线衍射等表征及研究。标题化合物属于三斜晶系,空间群P1,a=0.702 71(14)nm,b=0.828 98(17)nm,c=1.233 1(3)nm,α=84.32(3)°,β=73.90(3)°,γ=67.26(3)°,V=0.636 5(2)nm3,Z=2,R=0.056 5。Ag1离子分别与来自3个不同HL2-配体的4个氧原子和1个乙腈分子中的氮原子配位,展示出扭曲的四方锥几何构型,而Ag2离子则分别与来自4个不同HL2-配体的6个氧原子配位,展示出扭曲的八面体几何构型。相邻的银离子间通过磺酸基氧原子、羟基氧原子连接形成一维带状结构,该一维带进一步通过羧基氧桥联成二维层状结构。此外,该配合物在室温下具有较强的蓝光发射峰。     

一种新的配位聚合物[Cd(SCN)2(POM)2]n的合成和晶体结构(英)

The one-dimensional chain self-assembled coordination polymer, [Cd(SCN)₂(POM)₂]_n(where POM is 3-methyl-4-nitropyridine-N-oxide), was synthesized and characterized. The crystal data for the title coordination polymer: monoclinic, space group P2₁/c, a = 1.182 3(1) nm, b = 0.591 1(1) nm, c = 1.419 2(1) nm, β = 102.875(1)°, Z=2, μ = 1.391 mm^-1, final R₁ = 0.062 8, wR₂ = 0.145 2. The coordination polymer exhibits a strong fluorescent emission band at ca. 518 nm. CCDC: 211506.     

Polymer sheets with a thin nanocomposite layer acting as a UV filter

A surface layer (thickness 1–10 μm) containing colloidal TiO₂ or ZnO particles was prepared in EVA (a copolymer of ethylene and vinyl acetate). The inorganic particles were formed in situ by hydrolysis of incorporated titanium tetrachloride or diethyl zinc. The resulting materials were analyzed with UV spectroscopy, electron microscopy, X-ray diffraction, thermogravimetric analysis and atomic emission spectroscopy. The average diameter of the embedded TiO₂ particles was 70 nm; these particles absorb UV radiation but also induce opacity in the polymer sheets in the visible wavelengths range. The ZnO particles were smaller (average diameter 15 nm); with a surface layer of embedded ZnO, transparent polymer sheets can be obtained that absorb UV radiation. © 1997 John Wiley & Sons, Ltd.     

原位水热合成一个新颖的银四唑配位聚合物(英)

在水热条件下，硝酸(3-氰基吡啶)银以及叠氮化纳反应,成功地组装了一个二维层状银四唑配位聚合物[mono(5-(3-pyridyl)tetrazolato)Ag] (1),并对其进行了表征。晶体结构分析表明，化合物1结晶在三斜晶系，其空间群分别为P1(a=0.626 08(10) nm，b=0.784 98(13) nm，c=0.805 84(12) nm，α=75.171(4)°，β=76.653(3)°，γ=68.332(3)°，V=0.351 67(10) nm³，Z=2)，银的配位环境为四配位并形成略为变形的四面体构型。室温下，化合物1显示强的蓝色荧光(495 nm和521 nm)。     

发光的二维Cu(Ⅰ)分子箱[CuCl(DBBD)2]n

Hydrothermal treatment of CuCl and atropisomeric ligand racemic-diethyl (R,S)-4,4′-biquinoline-6,6′-diethyl-3,3′-dicarboxylate (DBBD) (1) in the presence of H₂O and C₂H₅OH over 4 days at 104～109 ℃ yielded colorless block crystals [CuCl(DBBD)₂]_n (2). The compound exhibits strong red fluorescent emission with a wavelength of 650 nm. The crystal of [CuCl(DBBD)₂]_n belongs to monoclinic system with space group C2/c, and a=1.656 58(17) nm, b=2.025 0(2) nm, c=1.548 73(16) nm, β=107.879(2)°, V=4.944 4(9) nm³, D_c=1.417 g·cm^-3, Z=8. CCDC: 292932.     

一维梯形蓝色荧光磺酸锶配位聚合物

The reaction of 3-carboxy-4-hydroxybenzenesulfonic acid with SrCl₂·6H₂O yields one-dimensional double-chain coordination polymer {[Sr(H₂SSA)₂(H₂O)₄]·2H₂O}_n (1), which displays strong blue fluorescence emission (λ_max=423 nm) in the solid-state at room temperature. Crystal data for 1: Triclinic, space group P1, a=0.688 48(2) nm, b=0.706 86(2) nm, c=2.474 22(7) nm. α=96.458(2)°, β=90.796(2)°, γ=108.628 0(10)°, V=1.132 19(6) nm³, Z=2, 16 575 unique data (θ_max=25.99°), R=0.021 1 (4 411 [I≥2σ(I)] reflections), wR=0.052 5 (all data), ρ_max=0.881 e·nm^-3. CCDC: 279677.     

High-performance blue electroluminescent devices based on 2-(4-biphenylyl)-5-(4-carbazole-9-yl)phenyl-1,3,4-oxadiazole

An electron transporting moiety (1,3,4-oxadiazole) and a hole transporting moiety (carbazole) were combined to create 2-(4-biphenylyl)-5-(4-carbazole-9-yl)phenyl-1,3,4-oxadiazole (CzOxa), a three layer device with a configuration of ITO/TPD(50 nm)/CzOxa(40 nm)/AlQ(40 nm)/Mg0.9Ag0.1(200 nm)/Ag(80 nm) which exhibited a blue emission peak at approximately 470 nm (x = 0.14, y = 0.19) with a maximum luminance of 26,200 cd m(-2) at a drive voltage of 15 V and a maximum luminous efficiency of 2.25 lm W(-1).     

基于蓝黄磷光二元互补色的高效聚合物白光器件

研究了基于互补色的高效聚合物白光器件,双色材料包括蓝绿光材料双(4,6-二氟苯基吡啶-N,C2)吡啶甲酰合铱(Firpic)和黄光材料三[3-(2,6-二甲基苯氧基)-6-(2-噻吩基)-哒嗪]铱(Fs-1),器件结构为ITO/PEDOT(40 nm)/PVK:OXD-7:Firpic:Fs-1(80 nm)/Ba(4 nm)/Al(120 nm).当发光层材料PVK∶OXD-7∶Firpic∶Fs-1质量比为63∶27∶10∶0.25时,用溶液加工方法得到高效白光器件,此时CIE色坐标为(0.30,0.39),最大电流效率为10.8 cd.A-1,亮度可达到4200 cd.m-2.在此基础上,引入水溶性电子注入材料聚[9,9-二(3′-N,N-二甲基胺基丙基-2,7-芴-2,7-交-(9,9-二辛基芴)](PFN)修饰阴极界面,使载流子注入和传输更平衡,当阴极为PFN(20 nm)/Al(120 nm)时,电流效率获得显著改善,达到13.1 cd.A-1,此时电流密度为4.9 mA.cm-2,亮度可达到6096 cd.m-2,白光器件的色坐标为(0.33,0.39),同时发光光谱稳定.另外通过电致发光(EL)、光致发光(PL)光谱及能级结构图分析了载流子俘获和能量转移在发光中的作用.     

单一手性锌配位聚合物：晶体结构，荧光及介电性质

在原位水热条件下,单一手性有机配体(S)-甲基-2-(4-氰基苯胺)-3-(4-羟基苯)丙酸甲酯与叠氮化钠和氯化锌反应,得到了一个新的四唑锌配位聚合物{[Zn(TBHPA)H2O].H2O}n(1,TBHPA=(S)-2-(4-(2H-tetrazol-5-yl)benzylamino)-3-(4-hydroxy-phenyl)propa-noic acid)。单晶结构表明该化合物结晶在手性空间群P212121,CD谱进一步证实该化合物固体粉末具有单一手性。倍频实验结果表明化合物1的SHG(倍频效应)响应大概是尿素的0.6倍。荧光测定结果显示该化合物在428 nm处有较强的荧光发射峰(激发波长319 nm)。另外,还研究了化合物1在室温条件下不同频率的介电常数变化。     

混合蓝色和绿色发射的高亮度白色有机电致发光器件

使用星形六苯芴类新材料1,2,3,4,5,6-hexakis(9,9-diethyl-9H-fluoren-2-yl)benzene (HKEthFLYPh)分别制备了三种不同结构的有机电致发光器件. 在结构为indium-tin oxide (ITO)/NPB (40 nm)/HKEthFLYPh (10 nm)/Alq3(50 nm)/Mg:Ag (200 nm)的器件中, 获得了两个电致发光谱峰分别位于435 和530 nm处的明亮白光. HKEth-FLYPh是能量传输层; N,N’-bis-(1-naphthyl)-N,N’-diphenyl-(1,1’-biphenyl)-4,4’-diamine (NPB)是空穴传输层和蓝色发光层; tris(8-hydroxyquinoline)aluminum (Alq3)是电子传输层和绿色发光层. 结果表明, 当驱动电压为15 V时, 器件的最大亮度达到8523 cd·m-2; 在5.5 V时, 器件达到最大流明效率为1.0 lm·W-1. 在电压为9 V时, CIE色坐标为(0.29, 0.34). 此外, 通过改变HKEthFLYPh层的厚度, 发现蓝色发射的相对强度随着HKEthFLYPh层厚度的增加而增强.     

以4-[(羧甲基)硫代]-苯甲酸为配体的Pb(Ⅱ)和Cd(Ⅱ)配位聚合物的合成、结构以及荧光性质

在混合溶剂热条件下,以4-[(羧甲基)硫代]-苯甲酸(CMTB)为配体合成了[Pb(CMTB)H2O]n(1)和[Cd(CMTB)]n(2)两个配位聚合物,并用X-射线单晶结构分析、电感耦合等离子光谱和红外光谱对其进行了表征。化合物1属于三斜晶系,空间群为P1,晶胞参数为a=0.645 08(13)nm,b=0.847 83(17)nm,c=0.956 30(19)nm,α=90.37(3)°,β=92.75(3)°,γ=106.40(3)°,Z=2;化合物1具有二维层状结构,每1个Pb(Ⅱ)与来自4个配体的5个氧原子以及1个来自水分子的氧原子配位,形成了1个变形八面体的几何构型。化合物2为单斜晶系,空间群是P21,晶胞参数为a=0.786 27(16)nm,b=0.600 55(12)nm,c=1.001 3(2)nm,β=91.14(3)°,Z=2。化合物2是一个二维层状化合物,Cd(Ⅱ)与5个氧原子和1个硫原子配位形成了六配位的八面体构型。同时,我们对两个配合物的荧光性质进行了研究。     

Dye-labeled silver nanoshell-bright particle

Silica beads with average diameters of 40-600 nm were prepared, and Ru(bpy)3(2+) complexes were incorporated into the beads. These beads were coated by silver layer by layer to generate porous but continuous metal nanoshells. The thicknesses of these metal shells were 5-50 nm. The emission band from the dyes in the silica cores was more narrow and the intensity was enhanced with growth of silver shell thickness due to coupling of the emission light from Ru(bpy)3(2+) in the cores with the metal plasmon from the silver shells. The enhancement of emission intensity was also dependent on the size of the silica core, showing that the enhancement efficiency decreased with an increase in the size of the silica beads. Lifetime measurements support the coupling mechanism between the dye and metal shell. This study can be used to develop novel dye-labeled metal particles with bright and narrow emission bands.