Ozonolysis of phenols in aqueous solution

In the ozonolysis of phenol in aqueous solution at pH 3, 7 and 10 the following products were quantified: catechol, hydroquinone, 1,4-benzoquinone, cis,cis-muconic acid, H2O2, 2,4-dihydroxybiphenyl and 4,4-dihydroxybiphenyl. At pH 10, material balance (products vs. phenol consumption) is obtained. Singlet dioxygen, O2(1 delta g), and .OH are formed as short-lived intermediates. The precursor of the latter, O3.-, and a phenoxyl radical is suggested to arise from electron transfer from phenol/phenolate to ozone. Addition of .OH to phenol gives rise to dihydroxycyclohexadienyl radicals which add dioxygen and eliminate HO2. thereby forming catechol/hydroquinone. In competition and catalysed by H+ and OH-, the dihydroxycyclohexadienyl radical eliminates water yielding a phenoxyl radical. At pH 10, they readily oxidize catechol and hydroquinone. This reforms phenol (accounting for the low phenol consumption) and yields higher-oxidised products, eventually 1,4-benzoquinone. cis,cis-Muconic acid can be accounted for by the Criegee mechanism, while O2(1 delta g) is released on the way to (some of the) catechol and hydroquinone. Similar reactions proceed with hydroquinone (products: 1,4-benzoquinone, 2-hydroxy-1,4-benzoquinone and H2O2, with high yields of O2(1 delta g) and .OH) and with catechol (products: 2-hydroxy-1,4-benzoquinone, cis,cis-muconic acid, H2O2 with high yields of O2(1 delta g) and .OH). Material balance is not obtained for these two systems. Pentachlorophenolate, pentabromophenolate and 2,4,6-triiodophenolate ions give rise to halide ions, O2(1 delta g) (58%/48%/10%) and .OH (27%/2%/0%). It is suggested that together with O2(1 delta g) the corresponding ortho- and para-quinones plus a halide ion are formed. Further halide ion is released upon the hydrolysis of these and other products. For pentachlorophenolate the material balance with respect to the short-lived intermediates is 85%. With the bromo- and iodophenolates the O2(1 delta g) yields are substantially lowered, most likely due to release of triplet (ground state) dioxygen induced by the heavy atom effect.     

醌类化合物在苯酚羟化反应中的电子传递作用

Fenton试剂是某些烃类化合物的有效氧化剂^[1],该体系对芳香化合物具有羟化作用。我们^[2]曾报道了含Cu类钙钛石型复合氧化物在苯酚烃化反应中的催化活性,并提出了相应的反应机理。高价态的过渡金属离子如C^3 [2]和Fe^3 [3]通常被认为是中间自由基的氧化剂。实际上,醌类化合物及其还原形式半醌、氢醌与生物体内许多电子转移过程密切相关^[4],如泛醌或辅酶Q在生物体呼吸链电子传递过程中起重要作用^[5]。在实验中我们观察到苯酚羟化反应中不仅有苯醌生成,而且生成的苯醌还能促进羟化反应。本文报道了醌类化合物在苯酚羟化循环中的传递电子作用。     

Photocatalytic mineralization of chlorinated organic pollutants in water by polyoxometallates. Determination of intermediates and final degradation products

Homogeneous aqueous solutions of organochlorine pesticides and chlorophenols, namely, lindane, hexachlorobenzene and 2,4-dichlorophenol (2,4DCP), undergo effective photodegradation upon photolysis with UV and near visible light in the presence of a characteristic polyoxometallate catalyst PW₁₂O₄₀ ³⁻. These substrates remained, practically, intact (lindane, HCB) or underwent minor degradation under similar conditions in absence of catalyst. The main oxidant appears to be OH radicals formed by the reaction of the excited polyoxometallate with H₂O. The system compares with the widely published TiO₂. Chlorohydroquinone (ClHQ), hydroquinone (HQ), chlorobenzoquinone (ClBQ), benzoquinone (BQ), 3,5-dichlorocatechol (3,5DCC) and 4-chlorocatechol (4CC), among others, were identified as the main aromatic intermediates in the photodegradation of 2,4DCP. Acetic acid was detected as ring cleavage product. In all cases the final photodegradation leads to complete mineralization of substrates to CO₂ and HCl.     

Simultaneous determination of hydroquinone and catechol based on glassy carbon electrode modified with gold-graphene nanocomposite

We have synthesized a virtually monodisperse gold-graphene (Au-G) nanocomposite by a single-step chemical reduction method in aqueous dimethylformamide solution. The nanoparticles are homogenously distributed over graphene nanosheets. A glassy carbon electrode was modified with this nanocomposite and displayed high electrocatalytic activity and extraordinary electronic transport properties due to its large surface area. It enabled the simultaneous determination of hydroquinone (HQ) and catechol (CC) in acetate buffer solution of pH?4.5. Two pairs of well-defined, quasi-reversible redox peaks are obtained, one for HQ and its oxidized form, with a 43 mV separation of peak potentials (ΔE_p), the other for CC and its oxidized form, with a ΔE_p of 39 mV. Due to the large separation of oxidation peak potentials (102 mV), the concentrations of HQ and CC can be easily determined simultaneously. The oxidation peak currents for both HQ and CC increase linearly with the respective concentrations in the 1.0 μM to 0.1 mM concentration range, with the detection limits of 0.2 and 0.15 μM (S/N?=?3), respectively. The modified electrode was successfully applied to the simultaneous determination of HQ and CC in spiked tap water, demonstrating that the Au-G nanocomposite may act as a high-performance sensing material in the selective detection of some environmental pollutants.

Quantum Chemical Approach for Determining Degradation Pathways of Phenol by Electrical Discharge Plasmas

This study uses density functional theory (DFT) simulations to predict the main pathways by which hydroxyl (OH) radicals oxidize phenol into monohydroxylated products during an electrical discharge directly in or contacting water. The calculated activation energies and reaction rate constants indicate that phenol ring H abstraction is less likely to occur than OH addition, which will be the fastest in the ortho and para positions. The chain propagation with molecular oxygen of such formed ortho and para radicals will result in the production of hydroquinone and catechol, which are, concurrently, the most likely products of phenol degradation by OH radicals. Electron transfer reactions between dihydroxycyclohexadienyl radicals and plasma oxidative species are another important reaction mechanism which may be contributing significantly to the formation of products. Good agreement between computed kinetic and experimental data demonstrates the feasibility of applying DFT to investigate chemical reaction mechanisms.     

Sensitive simultaneous determination of catechol and hydroquinone using a gold electrode modified with carbon nanofibers and gold nanoparticles

A highly sensitive electrochemical sensor for the simultaneous determination of catechol (CC) and hydroquinone (HQ) was fabricated by electrodeposition of gold nanoparticles onto carbon nanofiber film pre-cast on an Au electrode. Both CC and HQ cause a pair of quasi-reversible and well-defined redox peaks at the modified electrode in pH?7.0 solution. Simultaneously, the oxidation peak potentials of CC and HQ become separated by 112?mV. When simultaneously changing the concentrations of both CC and HQ, the response is linear between 9.0???M and 1.50?mM. In the presence of 0.15?mM of the respective isomer, the electrode gives a linear response in the range from 5.0 to 350???M, and from 9.0 to 500???M for CC and HQ, respectively, and detection limits are 0.36 and 0.86???M. The method was successfully examined for real sample analysis with high selectivity and sensitivity.

Enhanced Sensitive Electrochemical Sensor for Simultaneous Catechol and Hydroquinone Detection by Using Ultrasmall Ternary Pt-based Nanomaterial

The simple and effective method for the novel synthesis of Pt-based nanoparticle was presented with high efficiency. The sensitive catalyst for the simultaneous detection of catechol and hydroquinone was prepared by depositing ternary metal complex on fluorine-doped tin-oxide (FTO). The composition and morphology of nanomaterials were characterized by TEM, HRTEM, XRD, XPS, and EDS (energy dispersive spectroscopy). The size of the Pt-based nanomaterial was about 5±1 nm. The electrochemical performance of the modified catalyst was studied by CV, DPV, and EIS. The modified PtNiCu@FTO catalyst possessed good electro-oxidation activity for hydroquinone and catechol and used for simultaneous detection of catechol and hydroquinone at scan rate of 20 mV s⁻¹ (vs. Ag/AgCl). Detection responses were found in the ranges of 5–2900 μM for hydroquinone and 5–3000 μM for catechol. The detection limits (LOD) for HQ and CC were observed as 0.35 and 0.29 μM, respectively. The sensitivity of HQ and CC were 1515.55 and 1485 μA mM⁻¹ cm⁻², respectively. The prepared nanomaterial were effectively applied for the determination of CC and HQ in real samples.     

Simultaneous Determination of Hydroquinone and Catechol by Differential Alternative Pulses Voltammetry

The second order voltammetric technique of high resolution, Differential Alternative Pulses Voltammetry (DAPV), was applied for the simultaneous determination of hydroquinone (HQ) and catechol (CC) on bare spectroscopic graphite electrode. Well resolved anodic and cathodic peaks situated on both sides of the zero line were obtained, while the differential pulse voltammograms were overlapped. The linear concentration range for HQ and CC quantification by DAPV was extended up to 20 μmol L⁻¹ for both the isomers. The sensitivity of the determination was found to be 6.00 μA L μmol⁻¹ and 3.61 μA L μmol⁻¹, while the limit of detection reached was 0.2 μmol L⁻¹ and 0.5 μmol L⁻¹ for HQ and CC, respectively. No interference was observed from the commonly coexisting organic species such as resorcinol, phenol and p‐benzoquinone. The great resolution power of DAPV permitted obtaining excellent results without any electrode modification and any mathematical data processing.     

Selective determination of hydroquinone in the presence of catechol based on over-oxidized poly(hydroquinone)

Selective determination of hydroquinone (HQ) in the presence of catechol (CC) was developed at an over-oxidized poly(hydroquinone) (PHQ) electrode. The electrochemical polymerization of HQ was carried out by potentiostatic method on a glassy carbon electrode. The resulting PHQ was over-oxidized in 0.10?mol/L NaOH solution and thus poly(p-benzoquinone) was obtained. Two dihydroxybenzene isomers, HQ and CC, show different voltammetric behavior at the over-oxidized PHQ electrode. The peak current of HQ is much larger than that of CC with the same concentration, which is attributed to the different position of the hydroxyl groups in benzene ring of the two isomers. The results from electrochemical impedance spectroscopy also demonstrates that the over-oxidized PHQ electrode has a stronger affinity for HQ over CC.     

Covalent modification of glassy carbon electrode with aspartic acid for simultaneous determination of hydroquinone and catechol

Glassy carbon electrode (GCE) is covalently modified with aspartic acid (Asp). The modified electrode is used for the simultaneous electrochemical determination of hydroquinone (HQ) and catechol (CC) and shows an excellent electrocatalytical effect on the oxidation of HQ and CC by cyclic voltammetry (CV) in 0.1 mol/L acetate buffer solution (pH 4.5). In differential pulse voltammetric (DPV) measurements, the modified electrode could separate the oxidation peak potentials of HQ and CC present in binary mixtures by about 101 mV though the bare electrode gave a single broad response. A successful elimination of the fouling effect by the oxidized product of HQ on the response of CC has been achieved at the modified electrode. The determination limit of HQ in the presence of 0.1 mmol/L CC was 9.0 x 10(-7) mol/L and the determination limit of CC in the presence of 0.1 mmol/L HQ was 5.0 x 10(-7) mol/L. The proposed method has been applied to the simultaneous determination of HQ and CC in a water sample with simplicity and high selectivity.     

A graphene-based electrochemical sensor for sensitive and selective determination of hydroquinone

Graphene was prepared by electrochemical reduction of exfoliated graphite oxide at cathodic potentials, and used to fabricate a graphene-modified glassy carbon electrode (GCE) which was applied in a sensor for highly sensitive and selective voltammetric determination of hydroquinone (HQ). Compared to a bare (conventional) GCE, the redox peak current for HQ in pH 5.7 acetate buffer solution is significantly increased, indicating that graphene possesses electrocatalytic activity towards HQ. In addition, the peak-to-peak separation is significantly improved. The modified electrode enables sensing of HQ without interference by catechol or resorcinol. Under optimal conditions, the sensor exhibits excellent performance for detecting HQ with a detection limit of 0.8?μM, a reproducibility of 2.5% (expressed as the RSD), and a recoveries from 98.4 to 101.2%.

Selective and Simultaneous Determination of Dihydroxybenzene Isomers Based on Green Synthesized Gold Nanoparticles Decorated Reduced Graphene Oxide

In the present study, we report the simultaneous electrochemical determination of hydroquinone (HQ), catechol (CC) and resorcinol (RC) at gold nanoparticles (Au‐NPs) decorated reduced graphene oxide (RGO) modified electrode. An enhanced and well defined peak current response with a better peak separation of HQ, CC and RC is observed at RGO/Au‐NPs composite than that of RGO and Au‐NPs modified electrodes. The fabricated modified electrode shows a wide linear response in the concentration range of 3–90 µM, 3–300 µM and 15–150 µM for HQ, CC and RC, respectively. The detection limit of HQ, CC and RC is found as 0.15 µM, 0.12 µM and 0.78 µM, respectively.     

基于碳纳米管-石墨烯纳米片复合膜修饰金电极同时测定邻苯二酚和对苯二酚

制备了一种碳纳米管-石墨烯纳米片复合膜修饰金电极的用于同时测定邻苯二酚和对苯二酚电化学传感器。 并应用循环伏安法研究了邻苯二酚和对苯二酚在该电极上的电化学行为,邻苯二酚和对苯二酚的浓度检测采用差分脉冲伏安法,结果表明,碳纳米管-石墨烯纳米片复合膜极大的增强了邻苯二酚和对苯二酚的电催化活性。 并在0.5~6.0×10-4 mol/L浓度范围内与响应电流有良好的线性关系。邻苯二酚和对苯二酚的最低检测限分别是5.0×10-9和4.8×10-9 mol/L。 该电化学传感器能用于实际样品中的酚类化合物的检测。     

Electrochemical behavior of dihydroxybenzene isomers at MWCNTs modified electrode and simultaneous determination in neutral condition

Simultaneous determination of dihydroxybenzene isomers in neutral condition was successfully realized by a simple and easy prepared modified electrode without previous chemical or physical separations. The multi-walled carbon nanotubes modified glassy carbon electrode (MWCNTs/GCE), which was prepared by the drop-coating method, was characterized by FE-SEM and TEM. Then, the electrochemical behavior of dihydroxybenzene isomers at MWCNTs/GCE was systematically studied at different temperature and pH conditions. The oxidation peak potentials were separated in neutral condition with 105 mV to hydroquinone (HQ) and catechol (CC) and 390 mV to CC and resorcinol (RS). And in neutral condition, the amperometric current were found to be linear with concentration of HQ, CC, and RS (20–140 μM) with the presence of 100 μM other isomers. Furthermore, excellent anti-interference, stability, and reproducibility were also presented by this modified electrode.     

Covalent modification of a glassy carbon electrode with penicillamine for simultaneous determination of hydroquinone and catechol

A simple and highly selective electrochemical method has been developed for the simultaneous determination of hydroquinone (HQ) and catechol (CC) at a glassy carbon electrode covalently modified with penicillamine (Pen). The electrode is used for the simultaneous electrochemical determination of HQ and CC and shows an excellent electrocatalytical effect on the oxidation of HQ and CC upon cyclic voltammetry in acetate buffer solution of pH 5.0. In differential pulse voltammetric measurements, the modified electrode was able to separate the oxidation peak potentials of HQ and CC present in binary mixtures by about 103 mV although the bare electrode gave a single broad response. The determination limit of HQ in the presence of 0.1 mmol L⁻¹ CC was 1.0 × 10⁻⁶ mol L⁻¹, and the determination limit of CC in the presence of 0.1 mmol L⁻¹ HQ was 6.0 × 10⁻⁷ mol L⁻¹. The method was applied to the simultaneous determination of HQ and CC in a water sample. It is simple and highly selective.     

A Novel Sensor Based on Manganese azo‐Macrocycle/Carbon Nanotubes to Perform the Oxidation and Reduction Processes of Two Diphenol Isomers

The present work describes the development of a selective and sensitive voltammetric sensor for simultaneous determination of catechol (CC) and hydroquinone (HQ), based on a glassy carbon (GC) electrode modified with manganese phthalocyanine azo‐macrocycle (MnPc) adsorbed on multiwalled carbon nanotubes (MWCNT). Scanning electron microscopy and scanning electrochemical microscopy were used to characterize the composite material (MnPc/MWCNT) on the glassy carbon electrode surface. The modified electrode showed excellent electrochemical activity towards the simultaneous oxidation and reduction of CC and HQ. On the MnPc/MWCNT/GC electrode, both CC and HQ can generate a pair of quasi‐reversible and well‐defined redox peaks. Under optimized experimental and operational conditions, the cathodic peak currents were linear over the range 1–600 µmol L^?1 for both CC and HQ, with limits of detection of 0.095 and 0.041 µmol L^?1, respectively. The anodic peak currents were also linear over the range 1–600 µmol L^?1 for both CC and HQ, with limits of detection of 0.096 and 0.048 µmol L^?1, respectively. The proposed method was effectively applied for the simultaneous detection of hydroquinone and catechol in water samples and the results were in agreement with those obtained by a comparative method described in the literature.     

Comparative study of photo- and thermal catalytic hydroxylation of phenol with H2O2over TS-1

The hydroxylation of phenol into catechol (CAT) and hydroquinone (HQ) with hydrogen peroxide and TS-1 catalyst was carried out via both photo- and dark (thermal) reactions. The conversion of phenol and the product ratio of CAT/HQ in the photocatalytic reaction were higher than those in dark (thermal) reaction. This revised version was published online in June 2006 with corrections to the Cover Date.     

Electrochemical oxidation of phenolic and other organic compounds at boron doped diamond electrodes for wastewater treatment: effect of mass transfer

The paper presents the results of an experimental study on oxidation at boron doped diamond electrodes (BDD) of some phenolic compounds: phenol (PH), para-hydroxibenzoic acid (PHB), cathecole (CT), hydroquinone (HQ) are considered, singularly contained in aqueous solutions or in the presence of glucose (G), which was selected to represent the class of biodegradable compounds. Oxidation of benzoquinone (BQ) and maleic acid (MA), generally detected as intermediates products from phenol degradation, is also investigated. Great attention is paid to verify the feasibility of a selective process in which the oxidation is specifically addressed to the phenolic fraction up to non toxic intermediate products which are more biodegradable than the original phenols.     

Simultaneous determination of hydroquinone and catechol using a glassy carbon electrode modified with gold nanoparticles,ZnS/NiS@ZnS quantum dots and L-cysteine

We describe an electrochemical sensor for simultaneous determination of hydroquinone (HQ) and catechol (CC). A glassy carbon electrode (GCE) was modified with gold nanoparticles, L-cysteine, and ZnS/NiS@ZnS quantum dots using a layer-by-layer technique. The materials were characterized by X-ray diffractometry, field emission scanning electron microscopy, and electrochemical impedance and Fourier transform infrared spectroscopy. Cyclic voltammetry and differential pulse voltammetry revealed this modified GCE to represent a highly sensitive sensor for the simultaneous determination of HQ and CC. The anodic peak current for HQ at a working voltage of 80 mV (vs. Ag/AgCl) is related to its concentration in the 0.1 to 300 μM range (even in the presence of 0.1 mM of CC). The anodic peak current for CC at a working voltage of 184 mV is related to its concentration in the 0.5 to 400 μM range (even in the presence of 0.1 mM of HQ). The detection limits (at an S/N ratio of 3) are 24 and 71 nM for HQ and CC, respectively. The modified GCE was successfully applied to the determination of HQ and CC in aqueous solutions and gave satisfactory results.

A glassy carbon electrode was modified with gold nanoparticles, ZnS/NiS@ZnS quantum dots and L-cysteine and used for simultaneous determination of hydroquinone and catechol.

     

Simultaneous Determination of Catechol and Hydroquinone on Nano-Co/L-Cysteine Modified Glassy Carbon Electrode

In this study, a novel and highly sensitive electrochemical method for simultaneous determination of catechol (CC) and hydroquinone (HQ) was developed, which worked at GCE modified with Nano cobalt (Nano-Co) by electrodeposition and L-Cysteine by electrochemical polymerization. The Nano-Co/L-Cysteine GCE was investigated by cyclic voltammetry (CV), SEM and EIS. The excellent conditions have been selected including supporting electrolyte, pH, accumulation time and scan rate. The calibration curves of were obtained that the linear regression equation was I=0.0734c+6×10⁻⁶ in the range of 5.8 μM to 103 μM (R²=0.9942) for CC and the linear regression equation was I=0.0566c+5×10⁻⁶ in the range of 5.8 μM to 100 μM (R²=0.9967) for HQ. The obtained detection limits of CC and HQ both were 6×10⁻⁷ M. The modified electrode was successfully applied to the simultaneous determination of CC and HQ in water samples.