首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 156 毫秒
1.
To determine and compare the differences in soil water suction between uncropped and cropped plots, a 52-plot experiment was used. Three average tyre to soil contact pressures of 31, 41 and 62 kPa as well as four numbers of machines passes (1, 5, 10 and 15) and control plots of zero traffic were used as pre-seeding machinery compaction treatments for the investigation. Soil dry bulk density, soil moisture content, soil suction, rainfall, water table depth and corn yield were all measured. The results showed that, with increasing tyre contact pressure, there was a corresponding increase in soil suction during the growing season in both uncropped and cropped plots. A family of curves was drawn for soil suction versus tyre contact pressure for different numbers of days and also for soil suction versus volumetric water content at varying contact pressures and times of the season. Growth performance of corn plants was best in moderately compacted plots. Dry bulk density and penetrometer resistance were related to traffic treatments.  相似文献   

2.
A 52 plot experiment was performed during the growing season of 1977 in a Ste. Rosalie clay soil, using a randomized complete-block design with 13 treatments of machinery traffic within each of four blocks. Three vehicle contact pressures, four numbers of tractor passes, and a control of zero traffic were used to relate the growth and yield variables to wheel traffic and the resulting soil compaction. The number of days required for (a) plant emergence, (b) tasselling, and (c) silking were minimum in moderately compacted plots. The plant growth rate monitored at 41, 54, 68, and 105 days from the seeding time was different from plot to plot. Growth models at different times of the season were derived in terms of the wheel traffic variables, and plant and ear moisture content variation with traffic treatment was investigated. Yield and ear yield increased with increases in machine contact pressure and passes reaching a peak around 500 kPa and dropped off for further increases. The reduction in yield was over 35% in some cases, suggesting that careful traffic planning is essential to obtain better production in agricultural fields. Prediction models were obtained for all the plant growth characteristics in terms of traffic variables. A relation for yield in terms of soil bulk density was established for a dry season.  相似文献   

3.
This paper discusses the loading of a typical central Anatolian soil by the most commonly used corn and wheat production agricultural equipment. It further describes the effect that loading and soil conditions have on soil strength, namely compaction, and proposes techniques for minimizing undesired soil compaction. Experiments were carried out on a typical central Anatolian medium-textured imperfectly drained clay loam soil (Cambisol). Three different tillage methods and subsequently the same field operations were used for each rotation. Shear strength, penetration resistance, bulk density and moisture variations were detected in four sampling periods at each rotation. Tillage reduced the soil strength with the mouldboard plough causing the greatest loosening. However, natural processes and the vehicular traffic caused the soil to be re-compacted to about the same values as before. In any of the cases the obtained parameters did not exceed the critical values for plant growth except the penetration resistance in the 20–30 cm depth layer during corn production.  相似文献   

4.
This four-year experiment was conducted in north-west Slavonia (agricultural area of Croatia) to evaluate the effects of different tillage systems on compaction of silty loam soil (Albic Luvisol). The compared tillage systems were: (1) conventional tillage (CT), (2) conservation tillage (CM), (3) no-tillage system (NT), and the crop rotation was corn (Zea mays L.) – winter wheat (Triticum aestivum L.) – corn – winter wheat. For detecting the soil compaction, bulk density and penetration resistance were measured during the growing seasons. In all seasons and tillage systems, the bulk density and penetration resistance increased with depth and the greatest increase from surface to the deepest layer in average was observed at CT system. The bulk density and penetration resistance increased at all tillage systems during the experiment, but the greatest increase was also observed at CT system. The greatest bulk density (1.66 Mg m−3) and the greatest increase of 6.4% were observed at CT system in the layer 30–35 cm. In the first season, the bulk density was the greatest at NT system, but during the experiment the lowest average increase of 1.9% was observed at this system. The greatest penetration resistance of all measurements (5.9 MPa) was observed in the last season at CT system in depth of 40 cm. The lowest average increase of penetration resistance 11.4% was also observed at NT system. The highest yield of corn in the first season was achieved with CT system while in other seasons the highest yield of winter wheat and corn was achieved with CM system.  相似文献   

5.
Enhancement of the potential root growth volume is the main objective of farmers when they establish a conventional tillage system. Therefore, the main function of primary tillage is to increase soil’s structural macroporosity. In spite of this, during secondary tillage operations on these freshly tilled soils, the traffic on seedbeds causes significant increases in soil compaction. The aim of this paper was to quantify soil compaction induced by tractor traffic on a recently tilled non consolidated soil, to match ballast and tyre size on the tractors used during secondary tillage. The work was performed in the South of the Rolling Pampa region, Argentina. Secondary tillage traffic was simulated by one pass of a conventional 2WD tractor, using four configurations of bias-ply rear tyres: 18.4×34, 23.1×30, 18.4×38 and 18.4×38 duals, two ballast conditions were used in each configuration. Soil bulk density and cone index in a 0 to 600 mm profile were measured before and after traffic. Topsoil compaction increased as did ground pressure. Subsoil compaction increased as total axle load increased and was independent from ground pressure. At heavy conditions, topsoil levels always showed higher cone index values. From 150 to 450 mm depth, the same tendency was found, but with smaller increases in the cone index parameter, 22 to 48%, averaging 35%. Finally, at the deepest layer considered, 600 mm, differential increases due to the axle load are great enough as to be considered similar to those found in the upper horizon, 36 to 64%, averaging 55%. On the other hand, bulk density tended to be less responsive than cone index to the traffic treatments. Topsoil compaction can be reduced by matching conventional bias-ply tyres with an optimized axle weight.  相似文献   

6.
The changes in soil bulk density resulting from passage of tractor tires were measured for two typical agricultural soils at various water contents. These density changes were used to calculate relative compaction and variation in porosity with wheel sinkage. The results were displayed in graph form, and conclusions are drawn concerning achieving optimum porosity for various initial bulk densities and water contents.  相似文献   

7.
This is a documentary article describing the Institute's work concerning terramechanics. A brief history of the Soil Section outlines its purpose in relating the characteristics of agricultural machinery, the physical properties of soils and crop growth behaviour. The facilities of the Soil Section are described and its success in developing a high-resolution gamma-ray probe to measure soil bulk density and a recording penetrometer is described. Soil compaction measurements have been carried out for alternatives to the conventional tractor wheel and use of a drop-cone to measure soil plastic limit has been developed. Current efforts are focused on performance measurements of multiple-wheel configurations, four-wheel-drive tractors, consideration of soil compaction under modern crawler tracks and research on the effects on crop yield of soil loosening below normal ploughing depth. Development of prediction models for soil compaction is a major interest.  相似文献   

8.
Twenty-five treatments consisting of three vehicle contact pressures, 62, 41 and 31 kPa (0.63, 0.42, 0.32 kg/cm2), four numbers of tractor passes (1, 5, 10, 15,) before and after seeding groups, and a control of zero traffic were used to study the effect of soil compaction on corn plant root growth and distribution in a Ste. Rodalie clay soil. The average dry bulk density values for 0–20 cm depths measured during the season varied from a minimum of 0.89 g/cm3 to a maximum of 1.12 g/cm3 depending on the severity of the treatment. Root distribution maps were obtained for all the treatments by field measurements coupled with root washing methods. An average root density of 5.7 mg/g of soil in an uncompacted control plot was reduced to less than 2 mg/g in a plot with 15 passes of 0.63 kg/cm2 contact pressure. Soil penetration resistance values in various plots were compared, and a statistical model was obtained in terms of the traffic treatments, soil moisture content and depth. Yield reductions and penetration resistance were compared to root distrubution density results.  相似文献   

9.
Soil compactions are widely dispersed in the world but tend to be the most prevalent, where heavy machinery is used in agriculture. The increasing use of heavy machinery is the primary cause of soil and subsoil compaction. The impact of subsoil compaction on root growth and yield of wheat (Triticum aestivum L) were evaluated during 2006 and 2007. Sub-soil compactions were created by three normal loads, i.e. 4.40, 6.40 and 8.40 kg and four number of passes of tractor, i.e. 1, 6, 11 and 16. The field was divided into 39 plots including a control plot, i.e. no passes of the tractor. The size of each plot was 400 square meter. A factorial randomized block design was followed in laying out the experiment and care was taken that all the 13 treatments and their replications are included in field experiments. It was observed that for all the compaction treatments in the field experiment on the wheat crop, 51–61% of wheat roots were confined in 0–15 cm, 17–20% in 15–30 cm and the rest 22–28% is below 30 cm soil layer. Sub-soil compaction reduced the wheat crop yields to a maximum of 23%. A statistical model is developed to predict crop yield considering the root length density of the crop. Average root diameters increased with the increase of the sub-soil compaction level. In sub-soil zone, average root diameter decreased with the increase of sub-soil compaction level.  相似文献   

10.
Research was conducted to quantify the effect of tire variables (section width, diameter, inflation pressure); soil variables (soil moisture content, initial cone index, initial bulk density); and external variables (travel speed, axle load, number of tire passes) on soil compaction and to develop models to assess compaction in agricultural soils. Experiments were conducted in a laboratory soil bin at the Asian Institute of Technology in three soils, namely: clay soil (CS), silty clay loam soil (SCLS), and silty loam soil (SLS). A dimensional analysis technique was used to develop the compaction models. The axle load and the number of tire passes proved to be the most dominant factors which influenced compaction. Up to 13% increase in bulk density and cone index were observed when working at 3 kN axle load in a single pass using a 8.0–16 tire. Most of the compaction occurred during the first three passes of the tire. It was also found that the aspect ratio, tire inflation pressure and soil moisture content have significant effect on soil compaction. The initial cone index did not show significant effect. The compaction models provided good predictions even when tested with actual field data from previous studies. Thus, using the models, a decision support system could be developed which may be able to provide useful recommendations for appropriate soil management practices and solutions to site-specific compaction problems.  相似文献   

11.
Cone index, as determined by a cone penetrometer, is frequently used as a measure of soil strength. The index is a compound parameter involving components of shear, compressive and tensile strength and soil metal friction. In order to assess the effect of soil type and condition on the relative contributions of these components to penetration resistance, the forces required to push blunt and sharp probes into two soils under a range of moisture contents and bulk densities were investigated. The maximum penetration force in homogeneous soil was not uniquely related to dry bulk density or cohesion, but varied with soil moisture content.At high and low moisture contents, the soil tended to interact with the shaft of the penetrometer thus increasing the resistance to penetration. At low moisture content, bodies of compressed soil formed in front of the probe, effectively changing the probe geometry.It was concluded that interpretation of cone index in typical layered field soils is difficult. Even in homogeneous soils, the proportion of shear, compressive and tensile components that the cone index reflects varies with soil condition.  相似文献   

12.
The mechanical behaviour of the upper layers of a sandy loam soil was studied under standard triaxial compression and direct shear box tests. Variations of soil material properties were investigated at four different initial dry bulk densities of 1410, 1520, 1610 and 1670 kg/m3. Soil deformation and volume change under the triaxial compression loading were also studied at these bulk densities. Results from the two tests showed increases in the soil mechanical properties with the initial dry bulk density. The internal friction angle values measured with the triaxial compression apparatus exceeded those measured with the direct shear box. In contrast, the soil cohesion values measured with the direct shear box exceeded those measured with the triaxial compression apparatus. Under the triaxial compression test, the loose soil samples underwent contraction and volume reduction, whereas the dense samples swelled and failure cracks appeared clearly at various planes. The soil contraction for the former case characterizes the occurrence of soil compaction, whereas the cracks propagation and volume increase in the latter case characterizes the breaking up and loosening of soil during tillage operations. For the loose and moderately compacted states, the engineering Poisson's ratio increased with the axial strain until loading was completed. It also increased at the compacted and very compacted states until reaching given loading stages, after which its value started to decrease. This shifting in the engineering Poisson's ratio during loading may provide another identification of the moment of soil failure occurrence, in addition to that of the maximum shear stress.  相似文献   

13.
A 580/70R38 tractor drive tire with an aspect ratio of 0.756 and a 650/75R32 tire with an aspect ratio of 0.804 were operated at two dynamic loads and two inflation pressures on a sandy loam and a clay loam with loose soil above a hardpan. Soil bulk density and cone index were measured just above the hardpan beneath the centerline and edge of the tires. The bulk densities were essentially equal for the two tires and cone indices were also essentially equal for the two tires. Soil bulk density and cone index increased with increasing dynamic load at constant inflation pressure, and with increasing inflation pressure at constant dynamic load. In comparisons of the centerline and edge locations, soil bulk density and cone index were significantly less beneath the edge than beneath the centerline of the tires. Soil compaction is not likely to be affected by the aspect ratio of radial-ply tractor drive tires when aspect ratios are between 0.75 and 0.80.  相似文献   

14.
A statistical method for describing the distribution of aggregates and voids within tilled soil is used as the basis for a prediction technique. Transforms of aggregate-void and void-void transition probabilities are used in such a way that factors can be defined which describe how the soil structure differs under a range of circumstances. A standard structure is defined for a given soil as that which is produced at the 5 cm depth by one pass of a set of tines working at 10 cm depth when tillage is done at a speed of 1.4 m/s in soil at a water content equal to the plastic limit and which has previously grown a cereal crop. Factors are defined which describe deviations from this standard structure as a function of depth in the tilled layer, implement type, previous use of the soil, number of implement passes, water content at time of tillage, and subsequent compaction of thettilled layer. Application of the inverse transform then enables estimates of the distributions of aggregates and voids in the tilled layer to be predicted for required, specified conditions.  相似文献   

15.
A statistical method for describing the distribution of aggregates and voids within tilled soil is used as the basis for a prediction technique. Transforms of aggregate-void and void-void transition probabilities are used in such a way that factors can be defined which describe how the soil structure differs under a range of circumstances. A standard structure is defined for a given soil as that which is produced at the 5 cm depth by one pass of a set of tines working at 10 cm depth when tillage is done at a speed of 1.4 m/s in soil at a water content equal to the plastic limit and which has previously grown a cereal crop. Factors are defined which describe deviations from this standard structure as a function of depth in the tilled layer, implement type, previous use of the soil, number of implement passes, water content at time of tillage, and subsequent compaction of thettilled layer. Application of the inverse transform then enables estimates of the distributions of aggregates and voids in the tilled layer to be predicted for required, specified conditions.  相似文献   

16.
High axle loads, duration of strain as well as strain rate due to applied stresses, and field moisture condition have been found to contribute to compaction in the field. Numerous previous investigations on agricultural soil compaction were carried out with relatively dry soil. The aim of this study was to investigate the interrelationships between compaction, applied load, vehicle speed and a certain practical range of soil moisture content through a soil bin investigation of the compaction which results from the passage of a towed and a driven wheel. Soil pressure and the corresponding bulk density were analysed using a model proposed by Bailey et al. (J. agric Engng Res. 33, 257–262 (1986)) and ANOVA techniques. The results showed that compaction was higher at the higher moisture content level for both towed and driven conditions of the wheel, and that it was applied load that had the greatest contributory effect. Also, compaction was higher in the case of the driven wheel as compared to the towed wheel due to the phenomenon of slip sinkage. Bailey's model, it appears, can be utilized in the field for a practical estimation of compaction resulting from the passage of a towed wheel.  相似文献   

17.
Soil and test conditions important to earthmoving machinery have been found to be significantly different from all other fields of endeavour with the partial exception of tillage studies. This could be the subject of a long dissertation. Broadly, however, soil conditions which produce critical mobility problems are much too soft and/or wet to be of concern to the earthmoving contractor who has to meet rigid specifications on acceptable types and moisture contents of fill soils. Occasional soft spots are considered as nuisances instead of indicators of the need for major design compromises.

Civil engineers are concerned with the same types of soil, but in a vastly different context. They must design soil structures which will never reach initial soil failure. Earthmoving processes, on the other hand, must accept soil failures in many different forms and degrees and utilize post-failure soil strength to perform their tasks efficiently.

Tillage studies display many important similarities to earthmoving studies, particularly in regard to the types of soil failures of importance. They are, in reality, merely another form of earthmoving; by definition, if nothing more. Earthmoving processes can range into much stronger soils, but this alone is insufficient to set them apart.

The term Earthmoving Soil Mechanics was introduced in 1962(20). This paper more clearly defines the implications of the new terminology and illustrates the first successful application of soil mechanics and model analysis principles in the earthmoving industry.  相似文献   


18.
Studies were conducted for the establishment of safe axle loads for sugarcane hauling vehicles beyond which detrimental soil compaction would be induced. The treatments involved running a loaded test vehicle in field strips previously chosen at random. Safe loads were established by testing the level of significance of the difference in induced soil compaction between treated and non-treated sections. Working under soil moisture contents of 21.4–27.1% (dry basis), safe axle loads for two 18.4 × 30 tires were found to be 55.6 and 60.0 kN for sandy clay loam and sandy loam soils with initial dry bulk density about 1.434 g/cm3. These corresponded to ground contact pressures of 111 and 120 kPa, respectively.  相似文献   

19.
Agricultural traffic impacts on soil   总被引:2,自引:0,他引:2  
Alternate configurations of tires and tracks vary in their ability to generate tractive forces. These tractive elements also vary in the way that they impact the soil with some causing more soil disturbance than others. This soil disturbance includes soil compaction and rut formation which negatively impacts rainfall infiltration, rooting, and crop production while potentially increasing soil erosion and runoff. This paper will review a portion of the agricultural research that has been conducted related to soil impacts caused by the use of vehicle traffic in agricultural fields. Recommendations will also be made for ways to minimize the effects of vehicle traffic on soils when trafficking is necessary. These include: reducing axle load; reducing tractive element–soil contact stress by using radial tires, duals, and tracks; increasing soil drying prior to traffic; using conservation tillage systems which minimize vehicle traffic; using controlled traffic systems which eliminate random vehicle traffic across fields; and subsoiling to eliminate compacted soil profiles in crop growth zones. Soil compaction resulting from vehicle traffic may not be able to be completely eliminated, but it can be controlled and reduced through intelligent management of vehicle traffic.  相似文献   

20.
Three prior state-of-the-art reviews are used as a foundation for this one. Soil compaction research is divided into three areas: (1) Machines designed to compact the soil, or vehicles used intentionally to do so; (2) Incidental compaction of soil by machinery being used for other purposes; and (3) Management practices for controlling undersired soil compaction. Background research is discussed in each category, and the relevant papers for the Eight International Conference are summarized. It is concluded that the soil compaction problem is better understood and more effectively researched today than ever before. Continuation of the trend of the past half century toward larger and heavier agricultural machinery appears to be in jeopardy with the recognition of (1) total axle loads as the basic cause of subsoil compaction and (2) the nearly opposite soil conditions required for effective performance by wheels and crops.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号