弹性地基上转动FGM梁自由振动的DTM分析

基于Euler-Bernoulli梁理论,利用广义Hamilton原理推导得到弹性地基上转动功能梯度材料(FGM)梁横向自由振动的运动控制微分方程并进行无量纲化,采用微分变换法(DTM)对无量纲控制微分方程及其边界条件进行变换,计算了弹性地基上转动FGM梁在夹紧-夹紧、夹紧-简支和夹紧-自由三种边界条件下横向自由振动的无量纲固有频率,再将控制微分方程退化到无转动和地基时的FGM梁,计算其不同梯度指数时第一阶无量纲固有频率值,并和已有文献的FEM和Lagrange乘子法计算结果进行比较,数值完全吻合。计算结果表明,三种边界条件下FGM梁的无量纲固有频率随无量纲转速和无量纲弹性地基模量的增大而增大;在一定无量纲转速和无量纲弹性地基模量下,FGM梁的无量纲固有频率随着FGM梯度指数的增大而减小;但在夹紧-简支和夹紧-自由边界条件下,一阶无量纲固有频率几乎不变。     

Analytical solution for the electromechanical behavior of a rotating functionally graded piezoelectric hollow shaft

In the present paper, the analytical solution for a radially piezoelectric functionally graded rotating hollow shaft is presented. The variation of material properties is assumed to follow a power law along the radial direction of the shaft. Two resulting fully coupled differential equations in terms of the displacement and electric potential are solved directly. Numerical results for different shaft geometries with different profiles of inhomogeneity are also graphically displayed.     

Thermomagnetic viscoelastic responses in a functionally graded hollow structure

This paper presents an analytical solution for the interaction of electric potentials,electric displacements,elastic deformations,and thermoelasticity,and describes electromagnetoelastic responses and perturbation of the magnetic field vector in hollow structures(cylinder or sphere),subjected to mechanical load and electric potential.The material properties,thermal expansion coefficient and magnetic permeability of the structure are assumed to be graded in the radial direction by a power law distribution.In the present model we consider the solution for the case of a hollow structure made of viscoelastic isotropic material,reinforced by elastic isotropic fibers,this material is considered as structurally anisotropic material.The exact solutions for stresses and perturbations of the magnetic field vector in FGM hollow structures are determined using the infinitesimal theory of magnetothermoelasticity,and then the hollow structure model with viscoelastic material is solved using the correspondence principle and Illyushin’s approximation method.Finally,numerical results are carried out and discussed.     

Several three-dimensional solutions for transversely isotropic functionally graded material plate welded with circular inclusion

The problem of a transversely isotropic functionally graded material (FGM) plate welded with a circular inclusion is considered. The analysis starts with the generalized England-Spencer plate theory for transversely isotropic FGM plates, which expresses a three-dimensional (3D) general solution in terms of four analytic functions. Several analytical solutions are then obtained for an infinite FGM plate welded with a circular inclusion and subjected to the loads at infinity. Three different cases are considered, i.e., a rigid circular inclusion fixed in the space, a rigid circular inclusion rotating about the x-, y-, and z-axes, and an elastic circular inclusion with different material constants from the plate itself. The static responses of the plate and/or the inclusion are investigated through numerical examples.     

A Pressurized Functionally Graded Hollow Cylinder with Arbitrarily Varying Material Properties

The elastic analysis of a pressurized functionally graded material (FGM) annulus or tube is made in this paper. Different from existing studies, this study deals with an axisymmetrical FGM hollow cylinder or disk with arbitrarily varying material properties. A simple and efficient approach is suggested, which reduces the associated problem to solving a Fredholm integral equation. The resulting equation is approximately solved by expanding the solution as series of Legendre polynomials. The stresses and displacements can be represented in terms of the solution to the equation. For radius-dependent Young’s modulus, numerical results of the distribution of the radial and circumferential stresses are presented graphically. Our results indicate that change in the gradient of the FGM tube does not produce a substantial variation of the radial stress, but strongly affects the distribution of the hoop stress. In particular, the hoop stress may reach its maximum at an internal position or at the outer surface when the tube is internally pressurized. The results obtained are helpful in designing FGM cylindrical vessels to prevent failure.      

Creep relaxation in FGM rotating disc with nonlinear axisymmetric distribution of heterogeneity

Rotating discs are the vital part of many types of machineries. Usually there is a tendency to make use of them in higher rotational speeds, but ahead of their complete break down the incidence of vibration, plastic failure or creep relaxation can create serious damages which finally prevent the increase of the rotational speed. The invention of new materials has provided new opportunities to increase the loading capacity and speed of the discs. Functionally graded materials(FGMs) are a kind of new materials utilized in the construction of rotating discs. Consequently an important aspect in the analyses of heterogeneous FGM discs is the study of their creep relaxation. One of the well known constitutive equations for the modeling of creep phenomenon is known as the Sherby's law. Based on the steady state creep, the behavior of a variety of FGM rotating discs are studied. The analysis considers the conditions in which the distribution of volume fraction follows a power-law pattern. The required mathematical model and its solution for the analysis of stress and creep strain rate is represented. Some case studies are considered in which the effects of nonlinearly distributed volume fractions are studied. In the case studies, the analysis of rotating FGM discs made of Aluminum-Silicon Carbide compounds is considered. Besides, the analyses of discs with outside tractions are considered and the effects of typical material compositions upon the creep deformations are studied. For instance, the investigation discloses the significance of the use of FGM hubs in the turbine constructions.     

Elastic and viscoelastic solutions to rotating functionally graded hollow and solid cylinders

Analytical solutions to rotating functionally graded hollow and solid long cylinders are developed. Young＇s modulus and material density of the cylinder are assumed to vary exponentially in the radial direction, and Poisson＇s ratio is assumed to be constant. A unified governing equation is derived from the equilibrium equations, compatibility equation, deformation theory of elasticity and the stress-strain relationship. The governing second-order differential equation is solved in terms of a hypergeometric function for the elastic deformation of rotating functionally graded cylinders. Dependence of stresses in the cylinder on the inhomogeneous parameters, geometry and boundary conditions is examined and discussed. The proposed solution is validated by comparing the results for rotating functionally graded hollow and solid cylinders with the results for rotating homogeneous isotropic cylinders. In addition, a viscoelastic solution to the rotating viscoelastic cylinder is presented, and dependence of stresses in hollow and solid cylinders on the time parameter is examined.     

变速旋转部件的弹塑性和安定分析

本文研究了变速旋转部件(空心长轴、等厚度和变厚度圆盘)的弹塑性和安定分析,得到了在弹性极限、塑性极限和安定情况下角速度和角加速度之间的关系曲线,并讨论了屈服极限和圆盘厚度对这些曲线的影响。     

考虑剪切效应的旋转FGM楔形梁刚柔耦合动力学建模与仿真

本文对一类中心刚体-柔性梁系统在大范围转动下的刚柔耦合动力学问题进行了研究. 柔性梁为功能梯度材料(functionally graded materials, FGM)楔形变截面梁,材料体积分数在梁轴向呈幂律分布变化. 以弧长坐标来描述柔性FGM梁的几何位移关系,分别使用倾角和拉伸应变变量描述柔性梁的横向弯曲和纵向拉伸变形,并计及剪切效应. 采用假设模态法离散变形场,运用第二类拉格朗日方程进行方程推导,得到系统考虑剪切效应的刚柔耦合动力学模型. 基于全新的刚柔耦合动力学建模理论,研究不同轴向材料梯度分布的FGM楔形梁,通过数值仿真计算,分析讨论不同的转速、梯度分布规律以及变截面参数对系统动力学特性的影响. 结果表明,剪切效应对大高跨比的FGM楔形梁的变形影响较为明显,不容忽略;材料梯度分布规律和截面参数的选取均会对旋转FGM楔形梁的动力学响应和频率产生较大影响. 本文提出的考虑剪切效应的倾角刚柔耦合动力学模型是对以往非剪切模型的进一步完善,可应用于工程中的 Timoshenko梁结构的动力学问题求解.      

Analysis of the thermal stress behaviour of functionally graded hollow circular cylinders

This paper presents an analysis of the thermomechanical behavior of hollow circular cylinders of functionally graded material (FGM). The solutions are obtained by a novel limiting process that employs the solutions of homogeneous hollow circular cylinders, with no recourse to the basic theory or the equations of non-homogeneous thermoelasticity. Several numerical cases are studied, and conclusions are drawn regarding the general properties of thermal stresses in the FGM cylinder. We conclude that thermal stresses necessarily occur in the FGM cylinder, except in the trivial case of zero temperature. While heat resistance may be improved by sagaciously designing the material composition, careful attention must be paid to the fact that thermal stresses in the FGM cylinder are governed by more factors than are its homogeneous counterparts. The results that are presented here will serve as benchmarks for future related work.     

Limit angular velocities of variable thickness rotating disks

Elastic and plastic limit angular velocities are calculated for rotating disks of variable thickness in power function form. Analytical solution is obtained and used to calculate elastic limit angular velocities of variable thickness rotating annular disks and annular disks with rigid inclusion. An efficient numerical solution procedure is designed and used to obtain the elastic limit angular velocities of variable thickness rotating solid disks. Von Mises yield criterion and its flow rule is used to estimate plastic limit angular velocities. Both linear and nonlinear hardening material behaviors are treated numerically. The results are verified by comparing with those of uniform thickness rotating solid disks available in the literature. Elastic and plastic limit angular velocities are found to increase with the reduction of the disk thickness at the edge as well as the reduction in the disk mass due to the shape of the profile.     

Elastodynamic solution for plane-strain response of functionally graded thick hollow cylinders by analytical method

An elastodynamic solution for plane-strain response of functionally graded thick hollow cylinders subjected to uniformly-distributed dynamic pressures at boundary surfaces is presented. The material properties, except Poisson’s ratio, are assumed to vary through the thickness according to a power law function. To achieve an exact solution, the dynamic radial displacement is divided into two quasi-static and dynamic parts, and for each part, an analytical solution is derived. The quasi-static solution is obtained by means of Euler’s equation, and the dynamic solution is derived using the method of the separation of variables and the orthogonal expansion technique. The radial displacement and stress distributions are plotted for various functionally graded material (FGM) hollow cylinders under different dynamic loads, and the advantages of the presented method are discussed. The proposed analytical solution is suitable for analyzing various arrangements of hollow FGM cylinders with arbitrary thickness and arbitrary initial conditions, which are subjected to arbitrary forms of dynamic pressures distributed uniformly on their boundary surfaces.     

Development of instability in a rotating elastoplastic annular disk

The paper proposes a method, based on perfect-plasticity and perturbation theories, for instability analysis of an annular flat disk tightly set on a shaft with no interference fit. The perturbed elastoplastic state of the rotating disk is analyzed by determining the stress–strain state of a fixed elastic annular plate under in-plane loading. A characteristic equation of the first order for the critical radius of the plastic zone in the disk subject to internal pressure is derived. The critical rotation rate is calculated for different parameters of the disk     

Elastodynamic solution for plane-strain response of functionally graded thick hollow cylinders by analytical method

An elastodynamic solution for plane-strain response of functionally graded thick hollow cylinders subjected to uniformly-distributed dynamic pressures at boundary surfaces is presented. The material properties, except Poisson’s ratio, are assumed to vary through the thickness according to a power law function. To achieve an exact solution, the dynamic radial displacement is divided into two quasi-static and dynamic parts, and for each part, an analytical solution is derived. The quasi-static solution is obtained by means of Euler’s equation, and the dynamic solution is derived using the method of the separation of variables and the orthogonal expansion technique. The radial displacement and stress distributions are plotted for various functionally graded material (FGM) hollow cylinders under different dynamic loads, and the advantages of the presented method are discussed. The proposed analytical solution is suitable for analyzing various arrangements of hollow FGM cylinders with arbitrary thickness and arbitrary initial conditions, which are subjected to arbitrary forms of dynamic pressures distributed uniformly on their boundary surfaces.     

Acoustic radiation from a submerged hollow FGM sphere

An exact study based on the linear theory of elasticity is presented for the steady-state sound radiation characteristics of an arbitrarily thick radially inhomogeneous elastic isotropic hollow sphere, immersed in and filled with ideal compressible fluids, and subjected to an arbitrary axisymmetric time-harmonic driving force at its internal surface. A modal state equation with variable coefficients is set up in terms of appropriate displacement and stress functions and their spherical harmonics by means of the laminated approximation approach. Taylor’s expansion theorem is subsequently employed to solve the modal state equation, ultimately calculating a global transfer matrix. Numerical results are presented for a water-submerged/air-filled steel/zirconia FGM hollow sphere under an axisymmetric distributed internal pressure force. The effects of shell wall thickness, the material compositional gradient, frequency, and subtended polar angle of the internal pressure force on the far-field radiated pressure directivity patterns as well as the total radiated power are examined. It is demonstrated that the material gradient can significantly change the acoustical characteristics of hollow inhomogeneous sphere, especially for thick shells at high excitation frequencies. Limiting cases are considered and good agreements with available results as well as with the computations made by using a finite element package are obtained.     

旋转中心刚体-FGM梁刚柔热耦合动力学特性研究

对旋转中心刚体-功能梯度材料(functionally graded material,FGM)梁刚柔热耦合动力学特性进行研究.FGM梁为物理性能参数沿厚度方向呈幂律分布的欧拉伯努利梁.考虑柔性梁的横向弯曲变形和轴向拉伸变形, 并计入横向弯曲变形引起的纵向缩短,即非线性耦合变形量.考虑变截面空心梁在外部高温、内冷通道冷却情况下的热力耦合对系统动力学特性的影响,求解得到FGM梁沿厚度方向分布的温度场, 进而在本构关系中计入热应变.采用假设模态法对柔性梁变形场进行离散,运用第二类拉格朗日方程推导得到系统的刚柔热耦合动力学方程,并编制动力学仿真软件, 然后通过仿真算例对系统的动力学问题进行研究.结果表明:不同截面梁动力学响应差异较大, 因此需对实际系统合理建模;大范围运动已知时, 考虑热冲击载荷的FGM梁将有效抑制横向弯曲变形,而大范围运动恒定时随热冲击的叠加会出现高频振荡; 大范围运动未知时,外力矩和热冲击载荷相互作用产生热力耦合效应, 导致系统呈现高频振荡,同时与中心刚体大范围旋转运动产生刚柔热耦合效应.      

Irreversible deformation and subsequent unloading of a spherical elastoviscoplastic layer

Analytical solutions of a number of one-dimensional quasi-static problems that describe the processes of elastic deformation of the material of a hollow sphere and of generation and development of the plastic flow in this material with increasing pressure on the external boundary are presented. The process of unloading during slow removal of the loading pressure is studied. Stress fields, fields of elastic and plastic strains in the material of the spherical layer, the law of motion of the elastoplastic boundary, and residual stresses are determined. It is demonstrated that (in contrast to the ideal plasticity case) the allowance for the viscous properties of the material during its plastic flow eliminates the possibility of plastic flow emergence during unloading.     

Effects of electrorheological fluid core and functionally graded layers on the vibration behavior of a rotating composite beam

Vibration properties of a rotating Functionally Graded Electro-Rheological (FGER) beam are investigated. In the composition of three layered beam, an electrorheological fluid layer is embedded between two functionally graded material layers. Classical beam theory is applied in the analysis of Functionally Graded Material (FGM) layers. Using Hamilton??s principle and finite element method (FEM), equations of motion of the FGER beam are derived. The effects of various parameters such as FGM volume fraction index, rotating speed, thickness of the viscoelastic core and electric field on the resonant frequencies and modal loss factors are studied. The results quantify the significant effect of the FGM distribution and the ER core on the vibration suppression of the rotating composite beam.     

Buckling analysis of sandwich plates with FGM face sheets resting on elastic foundation with various boundary conditions: an analytical approach

This paper presents an analytical investigation on the buckling analysis of symmetric sandwich plates with functionally graded material (FGM) face sheets resting on an elastic foundation based on the first-order shear deformation plate theory (FSDT) and subjected to mechanical, thermal and thermo-mechanical loads. The material properties of FGM face sheets are assumed to be graded in the thickness direction according to a simple power law distribution in terms of the volume fractions of the constituents. The core layer is still homogeneous and made of an isotropic material. An analytical approach is used to reduce the governing equations of stability and then solved using an analytical solution which is named as power series Frobenius method for symmetric sandwich plates with six different boundary conditions. A detailed numerical study is carried out to examine the influence of the plate aspect ratio, side-to-thickness ratio, loading type, sandwich plate type, volume fraction index, elastic foundation coefficients and boundary conditions on the buckling response of FGM sandwich plates. This has not been done before and serves to fill the gap of knowledge in this area.     

Irreversible deformation with subsequent unloading of a spherical viscoelastoplastic layer

Analytic solutions are obtained for a sequence of one-dimensional quasistatic problems describing viscoelastic deformation processes in the material of a hollow ball and the plastic flow nucleation and evolution processes occurring in the ball as the pressure on the outer boundary increases. The unloading process under slow removal of the loading pressure is considered as well. The stress fields and the elastic and plastic strain fields in the spherical layer material, the law of motion of the elastoplastic boundary, and the residual stress level and distribution are computed. It is assumed that at the stage preceding the plastic flow the material obeys the viscoelastic Voigt model and the loading surface is determined by the von Mises plastic flow condition.