硅橡胶/氟橡胶并用胶的制备及力学性能

硅橡胶和氟橡胶作为国防、航天等重要领域的耐热材料一直被人们青睐,但其有着各自地优缺点且价格昂贵,本文尝试将这两种橡胶制成并用胶以解决氟橡胶不耐低温和加工性差的问题,以期增大其使用温度范围。采用机械共混法制备硅橡胶/氟橡胶并用胶,研究了硅橡胶和氟橡胶的混炼工艺、并用比、共硫化体系和硫化条件对并用胶力学性能的影响。结果表明,当硅橡胶/氟橡胶的质量比为10∶90,共硫化体系为3~#硫化剂/过氧化二异丙苯(DCP),一段硫化温度为170℃、硫化压力为10MPa、硫化时间为30min,二段硫化温度为200℃、硫化时间为6h时,并用胶的力学性能达到最好。     

偶氮四唑非金属盐的分子结构和热分解参数与其撞击感度间关联关系的研究

采用DFT 方法对偶氮四唑胍盐(GZT)等6 种偶氮四唑非金属盐进行了B3LYP/6-31G 水平的几何结构全优化, 计算了分子的最低空轨道能量(E_LUMO)、最高占有轨道能量(E_HOMO)及原子上的电荷分布等分子结构参数. 研究了偶氮四唑非金属盐的分子结构参数(包括氧平衡)和热分解参数(热分解温度和热分解活化能等)与其撞击感度之间的相关性. 结果表明, 偶氮四唑非金属盐的氧平衡越低, 撞击感度越低; 热分解温度和热分解活化能越低, 撞击感度越高; 取代基团上所带正电荷越大, 撞击感度越低.     

N,N′-二苯胺基己二酰胺β-晶型成核剂的热分解动力学分析

基于热重分析、微商热重分析及示差热分析研究了N,N′-二苯胺基己二酰胺β-晶型成核剂在空气气氛中的热分解动力学;通过利用Friedman方程和Flynn-Wall-Ozawa(FWO)方程对其热分解过程进行动力学分析求得了其热分解表观活化能;同时利用Achar-Brindly-Sharp方程和Coats-Redfern方程研究了其热分解机理,用等温热重分析法测得了失重10%时的寿命方程.结果表明,N,N′-二苯胺基己二酰胺β-晶型成核剂的表观活化能为138.66kJ.mol-1,其热分解反应的机理函数符合Mample法则,反应级数n=3/2,动力学方程为G(α)=α3/2,寿命方程为:lnτ=-51.877+2.922 2×104/T.     

La(NO3)3和Pr(NO3)3对高岭石脱羟基动力学的影响

采用热重和微商热重(TG/DTA)综合热分析技术在不同升温速率下研究了掺入La(NO₃)₃和Pr(NO₃)₃的高岭石的热分解过程, 利用Coats-Redfern积分法和Achar微分法对热分析实验数据进行动力学计算, 得到了高岭石脱羟基反应过程中的控制机理函数、 活化能和指前因子等动力学参数; 分析了2种稀土掺入对高岭石脱羟基过程动力学参数的影响, 并用Ozawa法对活化能进行了验证. 结果表明, 未掺稀土和掺入Pr(NO₃)₃的高岭石的脱羟基反应过程均受化学反应模型F₃控制, 反应的活化能分别为307.94和282.86 kJ/mol, 指前因子lnA的值分别为47.8980和44.1718; 掺入La(NO₃)₃的高岭石脱羟基反应过程控制机理函数发生改变, 受化学反应模型F₂控制, 反应活化能为196.02 kJ/mol, 指前因子lnA的值为29.5551. 与未掺稀土的高岭石对比, 掺入Pr(NO₃)₃后活化能和指前因子略有降低; 而掺入La(NO₃)₃后则显著降低, 分别降低了36.34%和38.30%. 采用Ozawa法验证得到的活化能与Coats-Redfern积分法和Achar微分法结果一致.     

新型磷系阻燃剂1,3,5-三(5,5-二甲基-1,3-二氧杂-2-氧代己内磷酰基- 2-氧)苯的合成及热分解动力学研究

以新戊二醇、三氯氧磷及1,3,5-三羟基苯等为原料, 经过两步反应合成新型磷系阻燃剂1,3,5-三(5,5-二甲基-1,3-二氧杂-2-氧代己内磷酰基-2-氧)苯, 采用元素分析、FT-IR、MS及1H NMR等技术确定了标题化合物的分子结构. 以TG-DTG为手段, 研究该新型磷系阻燃剂在氮气气氛中的热分解动力学; 利用Kissinger法、Flynn-Wall-Ozawa (FWO)法对其进行热分解动力学研究, 求出该阻燃剂的热分解动力学参数; 利用Coast-Redfern法研究该阻燃剂的热分解机理. 结果表明, Kissinger法所求得的表观活化能为171.72 kJ•mol－1, 指前因子ln A为37.57; Flynn-Wall-Ozawa法所求得的表观活化能为172.05 kJ•mol－1. 标题化合物的热分解动力学方程g(α)＝α1/4, 反应级数n＝1/4.     

硅藻土负载AgO复合材料的制备及热分解非等温动力学

采用化学氧化沉淀法, 以过硫酸钾为氧化剂制备了硅藻土负载过氧化银(AgO)复合材料, 并使用X射线衍射仪(XRD)、扫描电子显微镜(SEM)和激光粒度仪对其进行了表征, 借助热重(TG)分析研究了复合材料的热分解过程和非等温热分解动力学. 结果表明, 制备的复合材料为正方晶系方英石和单斜晶系AgO混合体, 且AgO质量分数为12.7%; 复合材料的中位径为18.53 μm, 比表面积为203.32 m²/kg, 颗粒的粒度分布在0.614~116.5 μm之间. 复合材料中AgO在171 ℃开始分解成Ag₂O, 在更高温度时Ag₂O进一步分解成Ag; 热分解反应服从以核生成和核成长为控制步骤的A1机理, 其热分解表观活化能为131.37 kJ/mol, 反应频率因子为3.19×10¹³ s^-1. 同自制的AgO粉末相比, 复合材料中AgO的热分解温度升高, 表观活化能上升约40 kJ/mol.     

TBIR改性BIIR/NR共混物的结构与性能

研究了新型合成橡胶——高反式-1,4-丁二烯-异戊二烯共聚橡胶(TBIR)对全钢轮胎气密层并用橡胶——溴化丁基橡胶(BIIR)/天然橡胶(NR)(质量比70/30)的改性作用,探讨了BIIR/NR/TBIR共混物的交联密度、填料分散性及力学性能,特别是并用硫化胶的气密性及屈挠疲劳性能等.结果表明,与无定型的BIIR和NR相比,结晶性TBIR的引入提高了炭黑填充的BIIR/NR/TBIR混炼胶的强度和模量,且随着TBIR用量的增大,混炼胶中TBIR的结晶熔融峰更明显,混炼胶的强度与模量显著提高.硫化特性结果表明,随着TBIR用量的增大,BIIR/NR/TBIR共混物的硫化速率略有提高,交联密度略有降低;TBIR用量为10~30份(生胶总质量的10%~30%)时,BIIR/NR/TBIR硫化胶在机械性能基本保持不变的情况下,耐热氧老化性能提高10%以上,耐一级屈挠疲劳性能提升2~5倍,气密性提高17%.炭黑分散结果表明,经过动态疲劳实验BIIR/NR硫化胶中炭黑聚集体的平均粒径增大至11.5μm,明显大于BIIR/NR/TBIR硫化胶中炭黑聚集体的平均粒径.对含TBIR硫化胶在周期性应力应变过程中的结构演变及对耐疲劳裂纹引发性能的影响机制进行了探讨,结果表明,TBIR可改性BIIR或者BIIR/NR制备高抗裂口引发的全钢轮胎气密层材料.     

双核铕-苯甲酸-邻菲咯啉三元络合物非等温热分解动力学研究

采用TG-DTG和DTA技术研究了Eu2(BA)6(PHEN)2 (BA苯甲酸根离子;PHEN1,10-邻菲咯啉)在静态空气中的热分解过程,根据TG曲线确定了热分解过程中的中间产物及最终产物,运用Acher法、Madhusudanan-Krishnan-Ninan (MKN)法和Flynn-Wall-Ozawa法对非等温动力学数据进行分析,推断出第一步热分解反应的动力学方程为dα/dt=Aexp(-E/RT)(1-α)2, 第一步热分解反应的活化能为135 kJ/mol, 活化自由能ΔG为149 kJ/mol, 活化焓ΔH为129 kJ/mol, 活化熵ΔS为-33 J/(mol·k), 同时用等温TG法得到失重10%为寿终指标的寿命方程为lnτ=-22.66+1.646×104/T.     

硅烷偶联剂改性碳纤维/硅橡胶/氟橡胶复合材料耐磨性和热性能研究

为了提高氟橡胶的耐磨性和耐低温性能,以硅橡胶与氟橡胶并用作为基相,偶联剂处理的碳纤维为增强相制备了碳纤维/硅橡胶/氟橡胶复合材料,研究了偶联剂种类及其用量对复合材料力学性能的影响,通过红外光谱和X射线光电子能谱证明偶联剂与碳纤维和橡胶基体发生了偶联作用,通过原子力显微镜和红外光谱成像对复合材料的表面形貌和相组成进行表征,通过动态热机械分析和热重分析研究复合材料的热性能。结果表明:偶联剂与碳纤维和氟/硅并用胶发生了交联反应,当选取2份KH590时复合材料的综合力学性能最佳,与氟橡胶相比,KH590/碳纤维/硅橡胶/氟橡胶复合材料的磨耗由0.0314cm~3·km~(-1)降低为0.0218cm~3·km~(-1),玻璃化转变温度由-20℃降低为-30℃,初始分解温度由231℃升高到304℃。     

配合物[Ni（H2B（pyrazolyl）2）2]的非等温热分解动力学研究

在甲醇溶液中用Ni(CH3COO)2.4H2O和NaH2B(pz)2常温下合成出了配合物[Ni(H2B(pz)2)2](pz=pyrazolyl),并用元素分析、红外光谱和X射线衍射等对配合物的结构进行了表征,对此配合物进行了非等温热分解动力学研究.采用了微分Achar和积分Coats-Redfern法分别拟合出配合物2个热分解阶段的动力学方程及相应的动力学参数.配合物第一热分解阶段可能的机理为三维扩散,球形对称,其动力学方程为dα/dT=3(A/β)e-E/RT[(1-α)-1/3-1]-1/2.配合物第二热分解阶段可能的机理为相边界反应,圆柱形对称(n=1/2),其动力学方程为dα/dT=2(A/β)e-E/RT(1-α)1/2.2个反应阶段的表观活化能平均值分别为260.87和176.27kJ/mol,lnA的平均值分别为65.65和37.11s-1.     

聚氨酯胶粘剂的热分解动力学研究

采用热分析技术考察了通用型聚氨酯胶粘剂在空气中的热解过程, 并通过TG方法和动力学方法研究了各步反应的活化能E、指前因子A等动力学参数. 通过等失重转化率法校验了两种方法所获得的E和A值. 结果表明, 聚氨酯胶粘剂有三个主要降解阶段, 第一降解阶段的活化能为144.31-148.35 kJ·mol^-1, 第二个降解阶段的活化能为196.96-204.26 kJ·mol^-1, 第三个降解阶段的活化能为202.97-205.27 kJ·mol^-1; 热降解过程为一级反应, 随着失重百分率的增大, 热分解反应活化能增大. 此外, 聚氨酯胶粘剂具有较高的热稳定性, 预测其在35 ℃的空气中失重5%时的热老化寿命为10年.     

Aging behavior and thermal degradation of fluoroelastomer reactive blends with poly-phenol hydroxy EPDM

In this paper, the aging behavior of the reactive blends of fluoroelastomer (FPM) with poly-phenol hydroxy ethylene propylene diene monomer rubber (PHEPDM) in hot air was firstly investigated. The aging mechanism was analyzed by the swelling experiment, attenuated total-reflectance Fourier-transform infrared (FTIR-ATR) spectroscopy and X-ray photoelectron spectroscopy (XPS). The results showed that the aging process increased the crosslinking density and the content of double bond. The O/F or O/C ratios increased and then decreased during aging because of the oxidation reaction of molecular chain and the surface migration of fluoro group. Secondly, thermogravimetric analysis (TGA) was used to study the thermal degradation behavior of the reactive blends. The apparent degradation activation energy (E) of FPM/PHEPDM reactive blends was calculated by the Kissinger and Coats-Redfern methods, respectively. The results showed that the FPM/PHEPDM reactive blends had higher thermal degradation temperature but lower E than FPM. Both the thermal degradation process of FPM/PHEPDM reactive blends and FPM were determined by nucleation and growth mechanism (Am). The general mechanism function was [−ln(1 − α)]^1/m. The optimum value of m was between 1/3 and 1/2 for FPM/PHEPDM reactive blends, but 1/2 for FPM. From the results above, it was deduced that the special structure of PHEPDM made itself surrounded by fluoroelastomer and protected from hot-air aging and thermal degradation.     

Kinetics of thermal degradation applied to biocomposites with TPS, PCL and sisal fibers by non-isothermal procedures

The thermal degradation behavior of the biocomposite with thermoplastic starch (TPS), poly(ε-caprolactone) (PCL) and bleached sisal fibers were investigated by thermogravimetry analysis (TG/DTG) under synthetic air atmosphere, differential scanning calorimetry, and their crystal structure by X-ray diffraction. Applying the non-isothermal Ozawa method, the TG/DTG curves average activation energy could be obtained for thermal degradation of the biocomposites with 5, 10, and 20 % of bleached sisal fibers. The apparent activation energy values for the biocomposites decreased when compared with the TPS/PCL blend, requiring lower energy to recycle this material. However, continuous addition of sisal fibers increased the activation energy of composites.     

New Regional Editor

Thermal decomposition of an agrowaste, namely banana trunk fibers (BTF) were investigated by thermogravimetry (TG) and derivative thermogravimetry (DTG) up to 900 °C at different heating rates (from 5 to 100 °C/min). The BTF was subjected to modification by means of various known chemical methods (mercerization, acetylation, peroxide treatment, esterification, and sulfuric acid treatment). Various degradation models, such as the Kissinger, Friedman, and Flynn–Wall–Ozawa were used to determine the apparent activation energy. The obtained apparent activation energy values (149–210 kJ/mol) allow in developing a simplified approach to understand the thermal decomposition behavior of natural fibers as a function of polymer composite processing.     

Thermodynamic analysis of decomposition of thiourea and thiourea oxides

Thiourea has exhibited extremely rich dynamical behavior when being oxidized either through a chemical approach or via an electrochemical method. In this study, thermodynamic properties of thiourea and its oxides are investigated by measuring their thermogravimetry (TG), differential thermogravimetry (DTG), and differential scanning calorimetry (DSC) simultaneously. Online FT-IR measurements show that products of the thermal decomposition vary significantly with the reaction temperature. In addition to the determination of their apparent activation energy (E), preexponential factor (A), and entropy (DeltaS++), enthalpy (DeltaH++), and Gibbs energy (DeltaG++) of thermal decomposition, our investigation further illustrates that the decomposition kinetics of thiourea and thiourea oxides follows the Johnson-Mehl-Avrami Equation, f (alpha) = n(1 - alpha)[-ln(1 - alpha)](1-1/n) and G(alpha) = [-ln(1 - alpha)](1/n) with n equal to 2, 3.43, and 3, respectively.     

Kinetics Analysis of the Thermal Decomposition of Poly(Butylene Adipate) Ionomers by Thermogravimetry (TG) and Derivate (DTG) Analysis

Kinetics analysis and thermal decomposition study of poly(butylene adipate) ionomers (PBAi) synthesized using the dimethyl 5‐sulfoisophthalate sodium salt (DMSI) of the diacid monomer were carried out by thermogravimetry (TG) and derivate (DTG) analysis. The decomposition kinetic parameters (activation energy, frequency factor) were calculated. The activation energy values of the PBAi‐2, PBAi‐3 and PBAi‐5 ionomers were respectively found as 164.51, 141.91 and 78.07 kJ/mol. The influence of DMSI content on the decomposition of the ionomers was investigated. The activation energy values decrease with increasing the content of DMSI. This suggests that increasing the content of DMSI makes the thermal decomposition of the ionomers easier.     

紫外光照射对皮胶原热降解活化能的影响

将皮胶原经不同时间的紫外光照射,采用热重法(TG)和微分热重分析(DTG)研究了照射前后皮胶原的热降解行为,用Horowitz-Metzger法和Coats-Redfern法计算了其热降解活化能,得到了未照射皮胶原和经过不同紫外线照射时间处理后的皮胶原的热降解活化能。研究发现,在较短时间(0~4h)的照射后,皮胶原的热降解活化能略有增大;在较长时间(8~64h)的照射后,皮胶原的热降解活化能大幅降低。这可能是由于在紫外光照射的过程中,皮胶原分子链发生了以交联为主和以断链为主的复杂光化学反应。     

TG studies of a composite solid rocket propellant based on HTPB-binder

Thermal decomposition kinetics of solid rocket propellants based on hydroxyl-terminated polybutadiene-HTPB binder was studied by applying the Arrhenius and Flynn-Wall-Ozawa's methods. The thermal decomposition data of the propellant samples were analyzed by thermogravimetric analysis (TG/DTG) at different heating rates in the temperature range of 300-1200 K. TG curves showed that the thermal degradation occurred in three main stages regardless of the plasticizer (DOA) raw material, the partial HTPB/IPDI binder and the total ammonium perchlorate decompositions. The kinetic parameters E _a (activation energy) and A (pre-exponential factor) and the compensation parameter (S _p) were determined. The apparent activation energies obtained from different methods showed a very good agreement. This revised version was published online in August 2006 with corrections to the Cover Date.     

N-(苯乙酰氨基)-N’-(α-萘乙酰基)硫脲的热解机理及热动力学研究

采用热重法(TG)和微分热重法(DTG)对合成的新型酰氨基硫脲类化合物——N-(苯乙酰氨基)-N’-(α-萘乙酰基)硫脲进行了热稳定性研究, 在25～600 ℃范围内有两次失重过程. 通过量子化学方法计算了分子的Mayer键级, 据此计算结果和热重分析结果提出了其热解机理. 并运用Kissinger和Ozawa等方法计算了其热解动力学参数. 得到第一阶段热解动力学方程为: dα/dt＝541.5exp(－38350/RT)(1－α)2.58; 第二阶段热解动力学方程为: dα/dt＝505.2exp(－64810/RT)• (1－α)2.12.     

Kinetic study of the polymeric binder burnout in green low temperature co-fired ceramic tapes

The binder decomposition and burnout process of a commercial low temperature co-fired ceramic (LTCC) tape and an alumina tape which is used as a sacrificial tape for the constrained sintering process of the LTCC-tape was investigated by thermogravimetry (TG) and derivative thermogravimetry (DTG) up to 550 °C at different heating rates (from 1.5 to 10 K min⁻¹) in air. TG revealed a multistage degradation behaviour of the binder system for both tapes, but the temperature range of the different degradation stages varied. The activation energy of decomposition was determined by the Flynn–Wall isoconversional method and the Coats–Redfern method.