Electrokinetic study of adsorption of ionic surfactants on titania from organic solvents

The electrokinetic potential of titania was studied as a function of concentration of SDS, DOSS and CTMABr in a series of solvents. In water and 50–50 water–methanol mixture, which are the most polar studied solvents, the organic ion is adsorbed on titania and the small inorganic ion remains in solution. In hexane the adsorption behavior is reversed, that is, the organic ion remains in solution and the small inorganic ion is adsorbed on titania. The borderline between these two types of behavior corresponds to solvent dielectric constant of about 25. In solvents, which have a dielectric constant in this range (methanol and 1-propanol) the adsorption preferences vary from one surfactant to another. The affinities of the organic ion and of the small inorganic ion to the surface are often similar, and then none of the ionic components is preferentially adsorbed, and the electrokinetic potential is not affected. In such cases, ionic surfactants are not suitable as agents for regulation of zeta potential.     

Synthesis of high surface area nanocrystalline anatase-TiO2 powders derived from particulate sol-gel route by tailoring processing parameters

Stabilised titania sols were prepared using an additive free particulate sol-gel route, via electrostatic stabilisation mechanism, with various processing parameters. Peptisation temperature, 50°C and 70°C, and TiO₂ concentration, 0.1, 0.2 and 0.4 molar, were chosen as processing parameters during sol preparation. Results from TiO₂ particle size and zeta potential of sols revealed that the smallest titania hydrodynamic diameter (13 nm) and the highest zeta potential (47.7 mV) were obtained for the sol produced at the lower peptisation temperature of 50°C and lower TiO₂ concentration of 0.1 M. On the other hand, between the sols prepared at 70°C, smaller titania particles (20 nm) and higher zeta potential (46.3 mV) were achieved with increasing TiO₂ concentration up to 0.4 M. X-ray diffraction (XRD) and Brunauer-Emmett-Teller (BET) results of produced powders annealed at different temperatures showed that the 300°C annealed powder made from 0.1 M sol prepared at 50°C was a mixture of anatase and brookite, corresponding to a major phase of anatase (∼95% estimated), with the smallest average crystallite size of 1.3 nm and the highest specific surface area (SSA) of 193 m²/g. Furthermore, increasing TiO₂ concentration up to 0.4 molar for the sols prepared at 70°C resulted in decreasing the average crystallite size (1.9 nm at 300°C) and increasing SSA (116 m²/g at 300°C) of the powders annealed at different temperatures. Anatase-to-rutile phase transformation temperature was increased with decreasing peptisation temperature down to 50°C, whereas TiO₂ concentration had no effect on this transition. Anatase percentage increased with decreasing both peptisation temperature and TiO₂ concentration. Such prepared powders can be used in many applications in areas from photo catalysts to gas sensors.     

Water-in-Oil-in-Water Nanoemulsions Containing Temulawak (Curcuma xanthorriza Roxb) and Red Dragon Fruit (Hylocereus polyrhizus) Extracts

Hydrophobic curcumin in temulawak extract and hydrophilic betacyanin in red dragon fruit extract are high-value bioactive compounds with extensive applications in functional food. In this study, these extracts were encapsulated in water-in-oil-in-water (w/o/w) nanoemulsions as a delivery system using a two-step high-energy emulsification method. PGPR and Span 20 were used as lipophilic emulsifiers for the primary w/o emulsion. The most stable w/o/w formulation with the least oil phase separation of 5% v/v consisted of w/o emulsion (15% w/w) and Tween 80 (1.5% w/w) as hydrophilic emulsifier. The formulation was characterized by a 189-nm mean droplet diameter, 0.16 polydispersity index, and –32 mV zeta potential. The freeze–thaw stability may be attributed to the combination of low w/o emulsion content and high Tween 80 concentration in the outer water phase of the w/o/w nanoemulsions used in this study. The IC₅₀ values of the nanoemulsion and the red dragon fruit extract were similar. It means that the higher concentration of curcumin in the nanoemulsions and the lower IC₅₀ value of temulawak extract ensured sufficient antioxidant activities of the w/o/w nanoemulsions.     

The Effect of the Liposomal Encapsulated Saffron Extract on the Physicochemical Properties of a Functional Ricotta Cheese

In this study, the encapsulation of saffron extract (SE) was examined at four various concentrations of soy lecithin (0.5%–4% w/v) and constant concentration of SE (0.25% w/v). Particle size and zeta potential of liposomes were in the range of 155.9–208.1 nm and −34.6–43.4 mV, respectively. Encapsulation efficiency was in the range of 50.73%–67.02%, with the stability of nanoliposomes in all treatments being >90%. Encapsulated SE (2% lecithin) was added to ricotta cheese at different concentrations (0%, 0.125%, 1%, and 2% w/v), and physicochemical and textural properties of the cheese were examined. Lecithin concentration significantly (p ≤ 0.05) affected the particle size, zeta potential, stability, and encapsulation efficiency of the manufactured liposomes. In terms of chemical composition and color of the functional cheese, the highest difference was observed between the control cheese and the cheese enriched with 2% liposomal encapsulated SE. Hardness and chewiness increased significantly (p ≤ 0.05) in the cheeses containing encapsulated SE compared to the control cheese. However, there was no significant difference in the case of adhesiveness, cohesiveness, and gumminess among different cheeses. Overall, based on the findings of this research, liposomal encapsulation was an efficient method for the delivery of SE in ricotta cheese as a novel functional food.     

Development,Characterization, and Immunomodulatory Evaluation of Carvacrol-loaded Nanoemulsion

Carvacrol (CV) is an essential oil with numerous therapeutic properties, including immunomodulatory activity. However, this effect has not been studied in nanoemulsion systems. The objective of this study was to develop an innovative carvacrol-loaded nanoemulsion (CVNE) for immunomodulatory action. The developed CVNE comprised of 5% w/w oily phase (medium chain triglycerides + CV), 2% w/w surfactants (Tween 80^®/Span 80^®), and 93% w/w water, and was produced by ultrasonication. Dynamic light scattering over 90 days was used to characterize CVNE. Cytotoxic activity and quantification of cytokines were evaluated in peripheral blood mononuclear cell (PBMC) culture supernatants. CVNE achieved a drug loading of 4.29 mg/mL, droplet size of 165.70 ± 0.46 nm, polydispersity index of 0.14 ± 0.03, zeta potential of −10.25 ± 0.52 mV, and good stability for 90 days. CVNE showed no cytotoxicity at concentrations up to 200 µM in PBMCs. CV diminished the production of IL-2 in the PBMC supernatant. However, CVNE reduced the levels of the pro-inflammatory cytokines IL-2, IL-17, and IFN-γ at 50 µM. In conclusion, a stable CVNE was produced, which improved the CV immunomodulatory activity in PBMCs.     

Dechlorination of poly(vinylidene chloride) in NaOH/ethylene glycol as a function of NaOH concentration, temperature, and solvent

The wet dechlorination treatment of poly(vinylidene chloride) (PVDC) was evaluated at atmospheric pressure in a solution of NaOH in ethylene glycol (EG), as a function of NaOH concentration, temperature, and solvent. Hydroxide ion from NaOH was required for dechlorination with EG acting solely as a solvent. The wet treatment exhibited significantly enhanced dechlorination efficiency over traditional thermal techniques, with a reaction efficiency as high as 92.8% in 1.0 M NaOH at 190 °C. Dechlorination reactions of PVDC in both NaOH/EG and NaOH/H₂O were expressed by an apparent first-order reaction. At 190 °C, the apparent rate constant in 1.0 M NaOH/EG was approximately 1.4 times larger than in 1.0 M NaOH/H₂O, with an apparent activation energy of 82.8 kJ mol⁻¹, indicating that the reaction proceeded under chemical control. The degree of dechlorination increased with increasing reaction temperature, favouring the elimination of HCl over the hydroxyl substitution of chloride.     

Polymerized Whey Protein Concentrate-Based Glutathione Delivery System: Physicochemical Characterization,Bioavailability and Sub-Chronic Toxicity Evaluation

Glutathione (GSH) is a powerful antioxidant, but its application is limited due to poor storage stability and low bioavailability. A novel nutrient encapsulation and delivery system, consisting of polymerized whey protein concentrate and GSH, was prepared and in vivo bioavailability, antioxidant capacity and toxicity were evaluated. Polymerized whey protein concentrate encapsulated GSH (PWPC-GSH) showed a diameter of roughly 1115 ± 7.07 nm (D₅₀) and zeta potential of 30.37 ± 0.75 mV. Differential scanning calorimetry (DSC) confirmed that GSH was successfully dispersed in PWPC particles. In vivo pharmacokinetics study suggested that PWPC-GSH displayed 2.5-times and 2.6-fold enhancement in maximum concentration (C_max) and area under the concentration–time curve (AUC) as compared to free GSH. Additionally, compared with plasma of mice gavage with free GSH, significantly increased antioxidant capacity of plasma in mice with PWPC-GSH was observed (p < 0.05). Sub-chronic toxicity evaluation indicated that no adverse toxicological reactions related to oral administration of PWPC-GSH were observed on male and female rats with a diet containing PWPC-GSH up to 4% (w/w). Data indicated that PWPC may be an effective carrier for GSH to improve bioavailability and antioxidant capacity.     

Rp-HPLC Determination of Quercetin in a Novel D-α-Tocopherol Polyethylene Glycol 1000 Succinate Based SNEDDS Formulation: Pharmacokinetics in Rat Plasma

Despite its proven efficacy in diverse metabolic disorders, quercetin (QU) for clinical use is still limited because of its low bioavailability. D-α-Tocopherol polyethylene glycol 1000 succinate (TPGS) is approved as a safe pharmaceutical adjuvant with marked antioxidant and anti-inflammatory activities. In the current study, several QU-loaded self-nanoemulsifying drug delivery systems (SNEDDS) were investigated to improve QU bioavailability. A reversed phase high performance liquid chromatography (RP-HPLC) method was developed, for the first time, as a simple and sensitive technique for pharmacokinetic studies of QU in the presence of TPGS SNEDDS formula in rat plasma. The analyses were performed on a Xterra C₁₈ column (4.6 × 100 mm, 5 µm) and UV detection at 280 nm. The analytes were separated by a gradient system of methanol and phosphate buffer of pH 3. The developed RP-HPLC method showed low limit of detection (LODs) of 7.65 and 22.09 ng/mL and LOQs of 23.19 and 66.96 ng/mL for QU and TPGS, respectively, which allowed their determination in real rat plasma samples. The method was linear over a wide range, (30–10,000) and (100–10,000) ng/mL for QU and TPGS, respectively. The selected SNEDDS formula, containing 50% w/w TPGS, 30% polyethylene glycol 200 (PEG 200), and 20% w/w pumpkin seed oil (PSO), showed a globule size of 320 nm and −28.6 mV zeta potential. Results of the pharmacokinetic studies showed 149.8% improvement in bioavailability of QU in SNEDDS relative to its suspension. The developed HPLC method proved to be simple and sensitive for QU and TPGS simultaneous determination in rat plasma after oral administration of the new SNEDDS formula.     

Synthesis and Characterization of Doxorubicin-Loaded Poly(Lactide-co-glycolide) Nanoparticles as a Sustained-Release Anticancer Drug Delivery System

The objective of the present study was to prepare a polymeric drug delivery system with no burst effect. To attain this goal, doxorubicin (Dox) as an effective anticancer drug was loaded into poly(lactide-co-glycolide) (PLGA) nanoparticles (NPs) to improve the drug performance and also maximize the release period. After the synthesis process, the freshly made PLGA NPs with two different lactide-to-glycolide ratios (75:25 and 50:50) were evaluated physically and chemically. To determine the encapsulation efficiency, a centrifugation method was applied. Also, the drug loading effect on particle size, polydispersity index, and zeta potential was examined. The results indicated that the NPs had nearly the same diameters around 360?nm, and the entrapment efficiencies for 75:25 PLGA and 50:50 PLGA were reported around 39 and 48?%, respectively. A slight increase in all parameters was observed due to the increase of the drug loading content. The primary release was 7.91?% (w/w) and 14.70?% (w/w) for 75:25 and 50:50 drug-loaded NPs, respectively; no burst effect was observed. After 20?days, the drug release was around 70.98 and 62.22?% of the total entrapped drug for 75:25 and 50:50 drug-loaded NPs, respectively. Finally, it was found that Dox was an appropriate anticancer agent with good capability to be encapsulated in polymeric NPs and could be released from the carriers with no burst effect and favor rate.     

Conductivity and Electrokinetic Potential of Microcrystalline Cellulose Particles in Aqueous HCl and NaOH Solutions

The conductivity of microcrystalline cellulose (MCC) dispersions in aqueous 10^–5–10^–2 M HCl and NaOH solutions was measured as a function of the particle volume fraction by the conductometry. The dependence of the relative conductivity of MCC particles on pH of equilibrium solutions was determined using the Wagner equation. The electrophoretic mobility of MCC particles in the aforementioned solutions was measured by the microelectrophoresis, and corresponding dependences of the particle potentials on pH of aqueous HCl and NaOH solutions (pH 2–11) were calculated using the Smoluchowski and Henry equations of the electrophoresis theory. It was shown that, in the case of MCC, the Henry equation, which allows for the significant conductivity of the dispersed particles, as compared with the dispersion medium, makes it possible to calculate more accurate potential values and, consequently, to derive the (pH) dependence, which is satisfactorily consistent with the effect of the surface charge and solution ionic strength on the potential in a wide pH range.     

Effect of Complexation on the Zeta Potential of Titanium Dioxide Dispersions

Abstract

The present paper deals with the surface charge properties and the dispersion stability of an aqueous titania suspension. Generally the titania powder surface is negatively charged. The dispersion stability of TiO₂ suspension is governed by the value of zeta potential. The zeta potential was measured as a function of barium acetate and zinc acetate concentrations, at pH 6.0, and the addition of electrolytes caused sharp decrease of surface charge. Ethylenediaminetetraacetic acid (EDTA) was used to chelate the bivalent metal ions, so that the charge of counterions was reduced. The complexation of bivalent counterions favors the increase of the negative zeta potential and the dispersion stability of aqueous TiO₂ suspension.     

The Effect of pH and Sodium Caseinate on the Aqueous Solubility,Stability, and Crystallinity of Rutin towards Concentrated Colloidally Stable Particles for the Incorporation into Functional Foods

Poor water solubility and low bioavailability of hydrophobic flavonoids such as rutin remain as substantial challenges to their oral delivery via functional foods. In this study, the effect of pH and the addition of a protein (sodium caseinate; NaCas) on the aqueous solubility and stability of rutin was studied, from which an efficient delivery system for the incorporation of rutin into functional food products was developed. The aqueous solubility, chemical stability, crystallinity, and morphology of rutin (0.1–5% w/v) under various pH (1–11) and protein concentrations (0.2–8% w/v) were studied. To manufacture the concentrated colloidally stable rutin–NaCas particles, rutin was dissolved and deprotonated in a NaCas solution at alkaline pH before its subsequent neutralisation at pH 7. The excess water was removed using ultrafiltration to improve the loading capacity. Rutin showed the highest solubility at pH 11, while the addition of NaCas resulted in the improvement of both solubility and chemical stability. Critically, to achieve particles with colloidal stability, the NaCas:rutin ratio (w/w) had to be greater than 2.5 and 40 respectively for the lowest (0.2% w/v) and highest (4 to 8% w/v) concentrations of NaCas. The rutin–NaCas particles in the concentrated formulations were physically stable, with a size in the range of 185 to 230 nm and zeta potential of −36.8 to −38.1 mV, depending on the NaCas:rutin ratio. Encapsulation efficiency and loading capacity of rutin in different systems were 76% to 83% and 2% to 22%, respectively. The concentrated formulation containing 5% w/v NaCas and 2% w/v rutin was chosen as the most efficient delivery system due to the ideal protein:flavonoid ratio (2.5:1), which resulted in the highest loading capacity (22%). Taken together, the findings show that the delivery system developed in this study can be a promising method for the incorporation of a high concentration of hydrophobic flavonoids such as rutin into functional foods.     

Electrocatalytic oxidation of methanol on a glassy carbon modified electrode by bis(1,2-phenylenediamine) nickel(II) complex

Electrocatalytic oxidation of methanol on a glassy carbon electrode coated with Ni(II)-(1,2-phenylendiamine)₂ (GC/NiOPD), conditioned by the potential recycling in a potential range of 100–650 mV (vs. SCE) is studied by cyclic voltammetry in an alkaline medium (0.10 M NaOH). The results show that the NiOPD layer formed at the surface of the electrode behaves as an efficient electrocatalyst for the oxidation of methanol in the alkaline medium via the Ni(III) species with a cross exchange reaction occurring throughout the layer at a low concentration of methanol. The effects of various parameters such as potential scan rates, methanol concentration and NiOPD surface concentration on the electro-oxidation of methanol are also investigated.     

Surfactant-assisted polyol preparation of nickel powders with different morphologies

Sub-micrometer nickel powders of controlled size and morphology were produced by a surfactant-assisted polyol method, using ethylene glycol (EG) as solvent and reductant in the presence of sodium dodecyl sulfate (SDS) surfactant and NaOH. The resultant Ni powders were characterized by XRD, SEM, EDS, and FTIR. Spherical, hexagonal, and triangular fcc Ni powders from 0.30 to 0.60 μm were obtained in the presence of SDS; irregular spherical fcc Ni powders were obtained in its absence. The concentrations of SDS, NaOH and Ni(CH₃COO)₂·4H₂O greatly influence the product morphology and size.      

Analysis of Nonsteroidal Anti-inflammatory Drugs in Water Samples Using Microemulsion Electrokinetic Capillary Chromatography Under pH-Suppressed Electroosmotic Flow with an On-Column Preconcentration Technique

Microemulsion electrokinetic capillary chromatography (MEEKC) in a suppressed electroosmotic flow (EOF) strategy was investigated for analysing a group of nonsteroidal anti-inflammatory drugs (NSAIDs) in water samples. The EOF was effectively suppressed with an acidic buffer as the aqueous phase. Four water immiscible solvents, oils (n-heptane, n-octane, ethyl acetate and di-n-butyl tartrate) and three organic solvents (methanol, 2-propanol and acetonitrile) were tested to optimise the pseudostationary phase and to obtain efficient separations. The optimum microemulsion background electrolyte (BGE) solution consisted of 0.8% (w/w) n-heptane, 6.6 (w/w) butan-1-ol, 15.0% (w/w) acetonitrile, 3.3% (w/w) sodium dodecyl sulfate (SDS), and 74.3% (w/w) of 25 mM sodium phosphate at pH 2.5. Stacking with reverse migrating pseudostationary phase (SRMP) was applied to enhance the concentration sensitivity of the NSAIDs. When this preconcentration technique was used, the sample stacking and the separation processes took place successively with the same voltage without an intermediate polarity switching step. Detection limits (LODs) in the order of 5–15 μg L⁻¹ for the NSAIDs were obtained using SRMP for standard solutions. The developed method was validated for the analysis of NSAIDs in tap water samples by combining an off-line solid-phase extraction (SPE) step and the on-column preconcentration technique SRMP. The LODs were in the 100–230 ng L⁻¹ range.     

On-line tracking of the coating of nanoscaled silica with titania nanoparticles via zeta-potential measurements

Nanoscaled spherical silica particles were directly coated with the titania nanoparticles by means of a heterogenic coagulation. Silica was prepared by the Stöber method, titania by a hydrolysis–condensation reaction of tetrapropylorthotitanate under acidic conditions. The on-line tracking of the coating process was performed by measuring the change in zeta potential during the gradual addition of a titania sol to the spherical silica particles. Silica particles of various sizes were used to determine the consumption of the titania sol in the dependence upon the particle size. The coated and uncoated particles were characterized by zeta-potential measurements, acoustic attenuation spectroscopy, dynamic light scattering, and scanning electron microscopy.     

Conventional residual liquid junction potentials in dilute solutions

Conventional residual liquid junction potentials were measured between NBS 1:1 phosphate buffer and various dilute solutions with ionic strengths of 1-100 mmol kg^?1, using 3.5 mol kg^?1 potassium chloride as the bridge electrolyte. All junctions were of the free-diffusion type, formed within a 1-mm capillary. The conventional residual junction potential was indistinguishable from zero (± 0.5 mV), for dilute solutions of primary reference standards, for which calculations based on the Henderson equation predict values of 0.8–1.3 mV. Solutions of Tris-HCl (20–100 mmol kg^?1) and dilute HCl (1–50 mmol kg^?1) had appreciable conventional residual liquid junction potentials (1.1–3.3 mV). The experimental values for dilute HCl solutions compare favourably with those calculated with the Henderson equation. These results suggest that the pH of hard waters, measured using the NBS pH scale, will be a good approximation (within 0.01 pH) to pa_H, so that pH can be interpreted in terms of the activity of the hydrogen ions. Further measurements are required to ascertain whether this approximation is true for soft and acidic waters.     

Infrared spectra of carbon monoxide adsorbed on a smooth gold electrode Part I. EMIRS spectra in acid and alkaline solutions

Electrochemically modulated infrared spectroscopy (EMIRS) was applied to the study of adsorption of CO on gold in 0.5 M sulfuric acid and 1 M sodium hydroxide solutions. A CO stretch band was observed with a peak intensity of ca. 0.2 % between 1850 and 2000 cm⁻¹ in 1 M NaOH, while a very weak band was detected between 1950 and 2050 cm⁻¹ in 0.5 M H₂SO₄. The bands were assigned to linear CO species adsorbed on the gold surface. In 1 M NaOH, electrooxidation of the strongly adsorbed CO species, which was detected by EMIRS, starts from ca. 0.5 V (RHE) with a sharp voltammetric current peak at 1.0 V at 50 mV/s, while electrooxidation of the bulk CO starts from ca. 0 V in the absence of the strongly adsorbed CO species on Au. The strongly adsorbed CO species acts as a poison for the electrooxidation of CO in the lower potential region.     

Removal of Copper(II) in the Presence of Sodium Dodecylobenzene Sulfonate from Acidic Effluents Using Adsorption on Ion Exchangers and Micellar-Enhanced Ultrafiltration Methods

The selective removal of Cu(II) in the presence of sodium dodecylobenzene sulfonate from acidic effluents was made using the adsorption and micellar-enhanced ultrafiltration methods. Lewatit MonoPlus TP220 showed the best adsorption behavior in the systems containing Cu(II) in the presence of ABSNa50 surfactant compared to the other adsorbents (removal efficiency ≈ 100%, sorption capacity ≈ 10 mg/g). The kinetics followed the pseudo-second order kinetic equation. The Langmuir adsorption capacities were 110 mg/g (the system with ABSNa50 above CMC) and 130.38 mg/g (the system with ABSNa50 below CMC). The working ion exchange capacities were C_w = 0.0216 g/mL and C_w = 0.0135 g/mL. The copper removal by the micellar-enhanced ultrafiltration method was 76.46% (0.1 mol/L HCl).     

PVC matrix membrane sensor for potentiometric determination of dodecylsulfate

The construction and performance characteristics of a new potentiometric PVC membrane sensor for the determination of sodium dodecyl sulfate (SDS) are described. The sensor was based on the use of an N-cetyl-N,N,N trimethyl ammonium (CTA) dodecyl sulfate (DS) ion pair as ion exchange sites in PVC matrix in the presence of o-nitrophenyl octylether as plasticiser. The sensor exhibited a fast, stable, and near-Nernstian response for SDS over the concentration range of 1 × 10^?3 to 10^?6 M at 25°C and the pH range 4–8.5 with anionic slope of 52.5 ± 0.5 mV decade^?1. The lower detection limit was 3 × 10^?6 M, and the response time was 25 s. Selectivity coefficients of SDS with respect to a number of different species were investigated. There were negligible interferences caused by most of the investigated anions. The determination of 1.0–280.0 µg mL^?1 of SDS in aqueous solutions showed an average recovery of 99.1%, and the mean relative standard deviation was 1.4 at 100 µg mL^?1. The results obtained in the determination of SDS in liquid soap, water and in some pharmaceutical preparations compared favourably with those obtained by the Methylene Blue active substance method (MBAS). In the present investigation, the DS sensor has been used as an end-point indicator electrode for some precipitation titration reactions, e.g. titration of SDS with CTMABr and cetylpyridinium chloride with SDS.