Al-SBA-15介孔分子筛的合成、表征及其在苯酚叔丁基化反应中的催化性能

 通过嫁接的方法合成了Al-SBA-15介孔分子筛,用X射线衍射、透射电子显微镜、低温N2吸附和NH3程序升温脱附等方法进行了表征,并研究了其在苯酚叔丁基化反应中的催化性能. 结果表明, Al-SBA-15保持了母体SBA-15高度有序的六方介孔结构,具有较强的酸性,且在苯酚叔丁基化反应中表现出比Al-MCM-41更好的催化活性和2,4-二叔丁基苯酚选择性.     

介孔分子筛SBA-15-SO3H催化合成油酸甲酯

在成功合成出含磺酸基的介孔分子筛SBA-15-SO3H的基础上，用于油酸与甲醇的酯化反应，考察该催化剂的催化性能，结果表明：在高级脂肪酸的酯化反应中，SBA-15-SO3H催化剂的活性高于沸石分子筛，与等摩尔数的硫酸的活性接近。考察了反应条件对SBA-15-SO3H催化剂性能的影响，得到油酸与甲醇酯化反应的最佳条件：反应温度60 ℃，甲醇与油酸的原料比为2∶1（摩尔），催化剂与原料比为1.5∶35（重量）。最后对催化剂的稳定性进行了考察，反应结果认为该催化剂在重复使用过程中活性未发生明显变化，反应前后的XRD分析结果认为，SBA-15-SO3H具有较高的水热稳定性。     

表面含磺酸基的介孔分子筛SBA-15-SO3H的直接合成

 采用水热法直接合成了含磺酸基的介孔分子筛SBA－15－SO3H．XRD表征结果表明，该分子筛具有规则的、六方立柱形的中孔结构，通过酸碱滴定和XRD确定了正硅酸乙酯／有机硅的最佳合成配比为9（α＝0．1）．29SiMASNMR固体核磁结果表明，含磺酸基的有机基团Si－（CH2）3－SO3H中的硅与SBA－15骨架上的氧通过Si－O键结合，形成稳定的有机／无机组成，FT－IR谱表明：在SBA－15－SO3H表面含有质子酸中心－SO3H．N2吸附－脱附和TEM结果表明，SBA－15－SO3H具有较大的比表面积、孔容和孔径，孔大小是单一的，孔分布是高度有序的．酯化反应结果表明，与后合成法相比，直接法合成的催化剂既具有较高的稳定性，又具有简便、快捷和高效的优点．     

表面含磺酸基的介孔分子筛催化剂SBA-15-SO3H的制备及其催化性能

采用直接和后合成两种方法制备出含磺酸基的介孔分子筛SBA-15-SO₃H,用XRD和红外光谱分析制备过程中催化剂结构和组成的变化.结果表明,两种方法制备出的含磺酸基的催化剂都保持了SBA-15分子筛的完整晶体结构,并含有质子酸中心-SO₃H;固体核磁共振表征结果证明,两种方法都使MPTMS存在于分子筛的表面;用N₂吸附-脱附测定了它们的比表面积、孔径和孔容;TGA分析认为,MPTMS在分子筛表面的热稳定性大于300℃,酸碱滴定结果说明,直接法获得的催化剂的酸中心多于后合成法.酯化反应结果表明,直接法合成的催化剂比后合成法具有更高的稳定性,且简便、快捷、高效.     

氨基功能化SBA-15介孔分子筛的制备与表征

以3-氨丙基三乙氧基硅烷为偶联剂,采用后合成法对介孔分子筛(SBA-15)的表面进行改性,制得氨基功能化的介孔NH<,2>-SBA-15材料(简称NH<,2>-SBA-15),其结构和性能经FT-IR,元素分析,XRD,SEM及低温N<,2>吸附-脱附表征.结果表明,氨基成功地嫁接到SBA-15表面,含量高达3.47 ...     

金复合介孔SBA-15吸附血红蛋白在H2O2电催化反应中的应用

以P123嵌段共聚物表面活性剂为模板剂制备介孔氧化硅SBA-15,并用沉积-沉淀(DP)法在SBA-15介孔表面负载纳米Au颗粒制备得到金复合介孔SBA-15材料(Au-SBA-15).再以Au-SBA-15材料制备玻碳修饰电极,将血红蛋白固定于修饰电极上用循环伏安法考察其对不同浓度H₂O₂溶液的电催化反应.在固定了血红蛋白的Hb/Au-SBA-15/GC修饰电极上,H₂O₂在+0.95 V处出现了氧化峰,且随着H₂O₂浓度的增大峰电流不断增加,说明金复合介孔氧化硅材料具有良好的生物兼容性,有利于血红蛋白的固定,其修饰电极对H₂O₂溶液具有一定的电催化作用.     

Al-MCM-41介孔分子筛催化对甲酚叔丁基化反应的研究

2-叔丁基对甲酚是一种有机中间体,在有机合成领域中占有重要地位,被广泛应用于表面活性剂、高档酚类抗氧化剂2246和2246-S、紫外线吸收剂UV-326等的生产[1]。特别是近十年来,以抗热老化为特征的功能性高档酚类抗氧化剂在国内外相继问世,它们对于提高聚合物材料的成型加工性能、     

苯基改性的中孔分子筛SBA-15的合成及其磺化

 在酸性条件下用正硅酸乙酯(TEOS)和苯基三乙氧基硅(PTES)直接缩合制备了苯基改性的中孔分子筛Ph-SBA-15,并用紫外光谱、红外光谱、X射线衍射、透射电镜和核磁共振等对改性后的样品进行了表征. 结果表明,在300 ℃下焙烧后,模板剂被脱除,而苯基可完整保留,苯基改性的SBA-15分子筛具有有序结构. 进一步用氯磺酸磺化改性后,可得到苯磺酸化的分子筛,其酸度可达4.19 mmol/g.     

介孔分子筛SBA-15的脂肪酶固定量分析测定

利用吸附法将假丝酵母脂肪酶(candida rugosa lipase,CRL)固定在介孔分子筛SBA-15上,对比了由单波长紫外分光光度法、双波长紫外分光光度法和二辛可宁酸法(bicinchoninic acid method, BCA)法测定的酶蛋白浓度及酶蛋白固定量.结果表明: SBA-15对紫外吸收有明显干扰,单波长紫外法测定结果远大于双波长紫外法和BCA法,双波长紫外法和BCA法测定结果较接近.利用BCA法测定了不同浓度CRL在介孔分子筛上的固定量,考察了固定化酶的泄漏量.在编号分别为Lu001和LLSD1的介孔分子筛SBA-15上的载酶量分别为16.6和114.12 mg/g.在缓冲溶液中SBA-15固定化酶的泄漏率只约为0.5%,可作为良好的酶固定化载体.     

SBA-15介孔分子筛表面的磺酸基改性及其催化性能

 采用后合成方法，将含有巯基的化合物3－巯丙基三甲氧基硅烷（MPTMS）键合在大孔径、厚孔壁的新型纯硅介孔分子筛SBA－15表面上，经氧化和酸化后得到含有强酸性的磺酸基团的固体酸催化剂SBA－15－SO3H．用X射线衍射、红外光谱、固体核磁共振及热失重等方法对改性前后的SBA－15样品进行了表征．结果表明，改性后SBA－15分子筛的结构未发生变化，MPTMS键合于分子筛的表面，改性后的分子筛具有质子酸中心．SBA－15－SO3H催化剂对十八碳烯酸与甲醇的酯化反应具有较高的活性，催化剂上的磺酸基团在反应过程中具有较好的稳定性．     

Preparation and characterization of vanadium(IV) oxide supported on SBA-15 and its catalytic performance in benzene hydroxylation to phenol using molecular oxygen

Preparation of dispersed transition metal oxides catalyst with low oxidation state still remains a challenging task in heterogeneous catalysis.In this study,vanadium oxides supported on zeolite SBA-15 have been prepared under hydrothermal condition using V 2 O 5 and oxalic acid as sources of vanadium and reductant,respectively.The structures of samples,especially the oxidation state of vanadium,and the surface distribution of vanadium oxide species,have been thoroughly characterized using various techniques,including N 2-physisorption,X-ray diffraction(XRD),transmission electron microscopy(TEM),X-ray photoelectron spectroscopy(XPS),UV-visible spectra(UV-Vis) and UV-visible-near infrared spectra(UV-Vis-NIR).It is found that the majority of supported vanadium was in the form of vanadium(IV) oxide species with the low valence of vanadium.By adjusting hydrothermal treatment time,the surface distribution of vanadium(IV) oxide species can be tuned from vanadium(IV) oxide cluster to crystallites.These materials have been tested in the hydroxylation of benzene to phenol in liquid-phase with molecular oxygen in the absence of reductant.The catalyst exhibits high selectivity for phenol(61%) at benzene conversion of 4.6%,which is a relatively good result in comparison with other studies employing molecular oxygen as the oxidant.     

SBA-15 supported HPW: Effective catalytic performance in the alkylation of phenol

SBA-15 was synthesized using non-ionic surfactant as the structure directing agent at 40 °C. It was then impregnated with different loadings (10, 30, 50 and 70%) of phosphotungstic acid. They were characterized by XRD, N₂ adsorption, FT-IR and DRIFT techniques. The physicochemical characterization revealed that SBA-15 could accommodate discrete phosphotungstic acid due to its large pore volume and high surface area. The catalytic activity of these materials was examined in the vapour phase tert-butylation of phenol using tert-butyl alcohol as the alkylating agent. The influence of reaction parameters such as reaction temperature, reactant feed ratio, WHSV and time on stream was studied, and the results were correlated with physicochemical characteristics of the catalysts. 4-tert-Butyl phenol was observed as the major product with high selectivity. Among the catalysts, 30% phosphotungstic acid supported SBA-15 showed high phenol conversion under optimum conditions, which is significantly higher than either phosphotungstic acid loaded mesoporous AlPO or AlMCM-41.     

介孔分子筛SBA-15的研究进展

介孔分子筛SBA-15具有独特的物理化学性质和广阔的应用前景,成为众多研究领域的一个研究热点.本文结合我们自己的工作和国内外相关研究,较全面地介绍了近年来SBA-15的研究状况,并展望了今后的发展方向和应用前景.     

不同助剂对CuO-ZnO/SBA-15催化CO_2加氢制甲醇性能影响的研究

以硅质骨架结构介孔分子筛SBA-15为载体,采用浸渍法合成CuO-ZnO/SBA-15(CZ/SBA-15)、CuO-ZnO-MnO_2/SBA-15(CZM/SBA-15)、CuO-ZnO-ZrO_2/SBA-15(CZZ/SBA-15)三组多孔催化剂,在固定床反应器上评价了各组催化剂催化CO_2加氢合成甲醇的性能,同时结合N_2吸附-脱附(BET)、X射线衍射(XRD)、H_2程序升温还原(H_2-TPR)、程序升温脱附(H_2-TPD、CO_2-TPD)、N_2O滴定、X射线光电子能谱(XPS)、透射电子显微镜(TEM)等表征研究了不同助剂对CO_2催化加氢制甲醇的影响。结果表明,催化剂中的金属氧化物改变了SBA-15分子筛载体的孔径大小和比表面积;催化剂CuO-ZnO-MnO_2/SBA-15、CuO-Zn O-ZrO_2/SBA-15中铜的分散度(D_(Cu))和比表面积(A_(Cu))更大,表面CuO粒径更小,更易被还原;相比Mn-O簇,Zr-O簇为增强了碱性位点,提高了甲醇选择性。此外,CuO-ZnO-ZrO_2/SBA-15具有更高的氧空位浓度,催化活性更好,其甲醇选择性为25.02%,与CuO-ZnO/SBA-15、CuO-ZnO-Mn O_2/SBA-15相比分别提高了28%和136.9%,催化效果最好。     

Carbon dioxide reforming of methane over Ni/Mo/SBA-15-La2O3 catalyst: Its characterization and catalytic performance

The Ni/Mo/SBA-15 catalyst was modified by La2O3 in order to improve its thermal stability and carbon deposition resistance during the CO2 reforming of methane to syngas. The catalytic performance, thermal stability, structure, dispersion of nickel and carbon deposition of the modified and unmodified catalysts were comparatively investigated by many characterization techniques such as N2 adsorption, H2-TPR, CO2-TPD, XRD, FT-IR and SEM. It was found that the major role of La2O3 additive was to improve the pore structure and inhibit carbon deposition on the catalyst surface. The La2O3 modified Ni/Mo/SBA-15 catalyst possessed a mesoporous structure and high surface area. The high surface area of the La2O3 modified catalysts resulted in strong interaction between Ni and Mo-La, which improved the dispersion of Ni, and retarded the sintering of Ni during the CO2 reforming process. The reaction evaluation results also showed that the La2O3 modified Ni/Mo/SBA-15 catalysts exhibited high stability.     

Ru/SBA-15的制备及其对水煤气变换反应的催化作用

制备了中孔分子筛SBA-15,以SBA-15为载体采用真空浸渍法制备了负载型Ru基水煤气变换反应的催化剂。利用透射电子显微镜、X-射线粉末衍射等方法对样品进行了表征。结果表明,合成的SBA-15分子筛孔径约为8 nm,粒径约为1 nm的Ru纳米粒子均匀分布在分子筛孔道中,添加适量的La2O3助剂可以显著提高催化剂的低温活性。当Ru和La2O3的负载量分别为4%和8%时,R4L8/SBA-15催化剂对CO转化率在255℃和265℃下分别达到56%和98%。     

Immobilization of acetylcholinesterase on functionalized SBA-15 mesoporous molecular sieve for detection of organophosphorus and carbamate pesticide

A novel method for the immobilization of acetylcholinesterase (AChE) on amino modified SBA-15 mesoporous molecular sieves was developed via electrostatic adsorption and glutaraldehyde crosslinking. The immobilized AChE could be exploited as a fast, sensitive and low-cost biocatalyst towards the detection of pesticides residues which could be stored at room temperature for a long time.     

SBA-15中异双核金属配合物的结构和催化性能

合成了四个具有混合价态的大环d-f异双核配合物[M1M2L](NO3)(H2O)n(L代表配体).采用浸渍法将四个d-f异双核配合物分别固载在中孔分子筛SBA-15上制得负载催化材料.SBA-15采用微波加热法合成.IR、UV-vis、 XRD、 ICP-AES和 TG/DTA技术表征表明,异双核配合物被固载后,配合物结构仍保持完整.以环己烷氧化为探针反应, 考察了上述负载催化材料的催化性能,并分析了不同金属离子或取代基对催化剂活性及选择性的影响.同时还系统考察了溶剂、反应时间、反应温度、对环己烷氧化反应的影响.结果表明,该催化剂在环己烷氧化反应中具有较好的活性及稳定性.