长度可控杆状SBA-15的合成

以三嵌段共聚物P123为结构导向剂, 天然高聚物壳聚糖为添加剂, 合成出分散性较好的杆状结构SBA-15. 通过调节体系中壳聚糖的含量, 可以实现对产物形貌的控制, 即从颗粒到短杆状, 最后到长杆状. 壳聚糖的加入不仅使SBA-15的介孔结构更加长程有序, 同时也提高了其比表面积和孔容, 其最高值分别达到1157 m²/g和1.53 cm³/g.     

Ag/SBA-15低温气相选择性催化氧化苯甲醇合成苯甲醛（英文）

以SBA-15为载体,采用浸渍法制备了不同Ag含量的Ag/SBA-15,通过N2吸附-脱附、X射线衍射、扫描电子显微镜、高分辨透射电子显微镜、X射线光电子能谱和电感耦合等离子体质谱对催化剂进行了表征.将Ag/SBA-15用于苯甲醇气相选择性催化氧化合成苯甲醛,研究了反应条件对转化率和选择性的影响.结果表明,Ag/SBA-15具有均一的一维孔道结构、较厚的孔壁(3–5 nm)及较大的比表面积(411–541 m2/g),其规整纳米空间的限域作用使一定负载量的Ag以纳米尺寸均匀分散于介孔SBA-15孔道内,增加了活性组分的比表面积.亲核性氧物种从Ag到SBA-15表面的氧溢流,提高了低温下Ag/SBA-15对苯甲醇气相选择性氧化合成苯甲醛的催化性能.5.3%Ag/SBA-15中的Ag粒径为5–6 nm,且均匀分散于载体孔道中,反应温度为220°C时,苯甲醇转化率为87%,苯甲醛选择性为95%;240°C时,苯甲醇转化率和苯甲醛选择性分别高达94%和97%;并在240–300°C范围内,其催化活性和选择性保持不变,表现出了良好的温度耐受能力.催化剂经活化再生可以连续使用40 h,选择性基本保持不变.     

Co-Fe/SBA-15与过一硫酸盐联用非均相催化降解水中染料罗丹明B

由于硫酸根自由基(SO4?-)的强氧化性,基于SO4?-的高级氧化技术受到人们的高度关注.采用过渡金属活化过一硫酸盐(PMS)产生SO4?-用以分解有机物,反应体系简单,反应条件温和,且不需要额外的能量供给,因此,成为人们优先选用的方法,其中,采用高效、环境友好的非均相过渡金属催化剂活化PMS处理难降解有机物成为研究热点.本文研究了非均相CoFe/SBA-15-PMS体系对水中难降解染料罗丹明B(RhB)的降解.以SBA-15为载体, Co(NO3)2·6H2O和Fe(NO3)3·9H2O为前驱物,采用一步等体积浸渍法制备了CoFe/SBA-15,通过X射线衍射(XRD)、N2吸附-脱附、扫描电镜(SEM)、能谱(EDS)、透射电镜(TEM)和振动样品磁强计(VSM)等对其进行了表征.考察了焙烧温度、Co与Fe的负载量对CoFe/SBA-15催化性能的影响和该催化剂的重复使用性能,还考察了RhB降解动力学及催化剂CoFe/SBA-15投加量、氧化剂PMS投加量和反应物(RhB和PMS)初始浓度对其性能的影响,探讨了RhB的降解机理.结果表明：对于催化剂CoFe/SBA-15,合成焙烧后在SBA-15上负载的Fe、Co化合物主要是CoFe2O4复合物,它作为催化剂的活性中心负载在SBA-15的孔道内外.制备的焙烧温度对CoFe/SBA-15催化性能几乎无影响,但对Co浸出影响显著.与SBA-15相比,催化剂10Co9.5Fe/SBA-15-700(Co和Fe负载量分别为10 wt%和9.5 wt%,焙烧温度700 oC)的比表面积、孔体积和孔径均减小,分别为506.1 m2/g,0.669 cm3/g和7.4 nm,但仍然保持SBA-15的有序六方介孔结构.该催化剂以棒状体的聚集态存在,聚集体直径大于0.25μm,其磁化强度为8.3 emu/g,因此,可通过外磁铁容易地从水中分离.相比之下,10Co9.5Fe/SBA-15-700具有最佳的催化性能和稳定性,可使RhB的降解率达到96%以上, Co的浸出量小于32.4μg/L.在CoFe/SBA-15和PMS共存下, RhB的降解符合一级动力学方程, RhB降解速率随CoFe/SBA-15和PMS投加量的增加和初始反应物浓度的减小而提高.淬灭实验结果表明,在CoFe/SBA-15, PMS和RhB水溶液体系中,存在的主要活性自由基为SO4?-,它是由CoFe/SBA-15活化PMS产生的,对RhB的降解起决定性的作用. RhB降解过程的UV-vis结果表明, RhB的降解途径主要是蒽环打开, SO4?-优先攻击RhB的有色芳香烃环,然后RhB进一步分解为小分子有机物. CoFe/SBA-15循环使用10次仍能保持高催化活性和稳定性,在每次反应中RhB的降解率均大于84%, Co和Fe的浸出量均分别小于72.1和35μg/L. CoFe/SBA-15作为高效、环境友好的非均相催化剂可有效地活化PMS产生SO4?-降解水中RhB,具有实际应用的潜力.     

Co-Fe/SBA-15与过一硫酸盐联用非均相催化降解水中染料罗丹明B（英文）

由于硫酸根自由基(SO·-4)的强氧化性,基于SO·-4的高级氧化技术受到人们的高度关注.采用过渡金属活化过一硫酸盐(PMS)产生SO·-4用以分解有机物,反应体系简单,反应条件温和,且不需要额外的能量供给,因此,成为人们优先选用的方法,其中,采用高效、环境友好的非均相过渡金属催化剂活化PMS处理难降解有机物成为研究热点.本文研究了非均相CoFe/SBA-15-PMS体系对水中难降解染料罗丹明B(RhB)的降解.以SBA-15为载体,Co(NO3)2·6H2O和Fe(NO3)3·9H2O为前驱物,采用一步等体积浸渍法制备了CoFe/SBA-15,通过X射线衍射(XRD)、N2吸附-脱附、扫描电镜(SEM)、能谱(EDS)、透射电镜(TEM)和振动样品磁强计(VSM)等对其进行了表征.考察了焙烧温度、Co与Fe的负载量对CoFe/SBA-15催化性能的影响和该催化剂的重复使用性能,还考察了RhB降解动力学及催化剂CoF e/SBA-15投加量、氧化剂PMS投加量和反应物(Rh B和PMS)初始浓度对其性能的影响,探讨了Rh B的降解机理.结果表明:对于催化剂CoFe/SBA-15,合成焙烧后在SBA-15上负载的Fe、Co化合物主要是CoFe2O4复合物,它作为催化剂的活性中心负载在SBA-15的孔道内外.制备的焙烧温度对Co Fe/SBA-15催化性能几乎无影响,但对Co浸出影响显著.与SBA-15相比,催化剂10Co9.5Fe/SBA-15-700(Co和Fe负载量分别为10 wt%和9.5 wt%,焙烧温度700 oC)的比表面积、孔体积和孔径均减小,分别为506.1 m2/g,0.669 cm3/g和7.4 nm,但仍然保持SBA-15的有序六方介孔结构.该催化剂以棒状体的聚集态存在,聚集体直径大于0.25μm,其磁化强度为8.3 emu/g,因此,可通过外磁铁容易地从水中分离.相比之下,10Co9.5Fe/SBA-15-700具有最佳的催化性能和稳定性,可使Rh B的降解率达到96%以上,Co的浸出量小于32.4μg/L.在CoFe/SBA-15和PMS共存下,RhB的降解符合一级动力学方程,Rh B降解速率随CoFe/SBA-15和PMS投加量的增加和初始反应物浓度的减小而提高.淬灭实验结果表明,在Co Fe/SBA-15,PMS和RhB水溶液体系中,存在的主要活性自由基为SO·-4,它是由CoFe/SBA-15活化PMS产生的,对RhB的降解起决定性的作用.RhB降解过程的UV-vis结果表明,RhB的降解途径主要是蒽环打开,SO·-4优先攻击RhB的有色芳香烃环,然后RhB进一步分解为小分子有机物.CoF e/SBA-15循环使用10次仍能保持高催化活性和稳定性,在每次反应中RhB的降解率均大于84%,Co和Fe的浸出量均分别小于72.1和35μg/L.CoFe/SBA-15作为高效、环境友好的非均相催化剂可有效地活化PMS产生SO·-4降解水中RhB,具有实际应用的潜力.     

高稳定性Ni/SBA-15催化剂的结构特征及其对二氧化碳重整甲烷反应的催化性能

 采用浸渍法制备了Ni含量为2.5%～20%的系列Ni/SBA-15催化剂,在常压连续流动固定床反应器上考察了催化剂对二氧化碳重整甲烷制合成气的催化性能,并用X射线衍射和N2吸附法研究了Ni/SBA-15催化剂的结构特征. 结果表明, Ni/SBA-15催化剂具有很高的CH4和CO2转化率, 12.5%Ni/SBA-15催化剂在800 ℃反应600 h后活性没有明显下降,但反应710 h后CH4的转化率下降了约50%, CO2的转化率下降了约25%. 其活性下降的主要原因是催化剂积炭. 在高温条件下反应时, SBA-15的介孔结构也没有遭到破坏,分子筛的孔壁能有效阻止活性组分Ni的团聚. SBA-15孔中组装一定量的Ni活性组分后,除了SBA-15的介孔外,还会形成另外一种较小的孔,但这不影响SBA-15的有序介孔结构,只是其孔径、孔容和BET比表面积降低.     

Pt／SBA-15、Pt／SBA-16催化剂的合成、表征及甲烷催化燃烧性能

以Na2SiO3.9H2O为硅源,H2PtCl6为铂源,水热法一步合成了Pt质量分数约1%的Pt/SBA-15和Pt/SBA-16催化剂.采用XRF、XRD、HRTEM等方法对样品进行了表征.在微型固定床反应器中考察了催化剂的甲烷催化燃烧性能.结果表明:合成的Pt/SBA-15和Pt/SBA-16样品分别具有SBA-15和SBA-16的高度有序的介孔结构;通过这种简便、低成本的方法可将Pt颗粒高分散地引入到样品的孔道内;催化剂表现出了较好的甲烷催化燃烧性能,在常压、原料气为含3.5%CH4的空气和GHSV=6000mL/(gcat.h)的反应条件下,在大约580℃下甲烷即可完全转化.     

高分散TiO_2/SBA-15的制备及光催化性能

提出了一种制备高分散TiO2/SBA-15光催化剂的新方法.以钛酸四正丁酯(TB)和羧基改性的SBA-15(COOH/SBA-15)为原料,利用COOH/SBA-15表面上高分散的羧基与TB的配合作用将TB锚定,经过溶剂热及焙烧处理制得TiO2/SBA-15光催化剂.采用粉末X射线衍射(XRD),N2吸脱附,傅里叶变换红外光谱(FT-IR),透射电镜(TEM)等对所得催化剂进行了表征.结果表明:所得TiO2/SBA-15光催化剂为高结晶度的锐钛矿晶型,TiO2均匀地分散在SBA-15表面,TiO2/SBA-15光催化剂保持较好的介孔特征结构,具有较大比表面积.以降解罗丹明B(RhB)为探针反应,考察了所得TiO2/SBA-15光催化剂的光催化性能.与后处理浸渍法制备的光催化剂相比,本文制备的TiO2/SBA-15光催化剂表现出了更加优越的光催化性能.     

Al3+离子介入提升（NH4）2SiF6对SBA-15介孔材料的水热稳定化作用

提出了一种(NH4)2SiF6处理提高SBA-15介孔材料水热稳定性的改良方法.采用SBA-15介孔材料中预引入Al3+离子,再进行1%SiO2计量的(NH4)2SiF6处理,最后用强酸洗脱预引入的Al3+.结果显示,由此处理的SBA-15材料,其水热稳定性明显优于相同条件下未预引入Al3+时(NH4)2SiF6处理的样品.两者在800°C、100%水蒸气处理12 h后,虽然均能很好保持其介观有序度、形貌及六方孔道结构,但前者的比表面积可高达271 m2/g,而后者仅为224 m2/g.表明Al3+离子介入能大幅度提升(NH4)2SiF6处理对SBA-15介孔材料的稳定化作用.这主要得益于预引入的骨架Al3+在保障(NH4)2SiF6处理修复SBA-15材料表面缺陷和进行表面疏水化、提升其水热稳定性的同时,能减缓(NH4)2SiF6释放的多余F-离子对SBA-15材料骨架的刻蚀破坏作用. Al3+离子介入的这种提升作用与其引入方式和SBA-15材料所经受的温度密切相关.     

Ag/SBA-15低温气相选择性催化氧化苯甲醇合成苯甲醛

以SBA-15为载体,采用浸渍法制备了不同Ag含量的Ag/SBA-15,通过N₂吸附-脱附、X射线衍射、扫描电子显微镜、高分辨透射电子显微镜、X射线光电子能谱和电感耦合等离子体质谱对催化剂进行了表征。将Ag/SBA-15用于苯甲醇气相选择性催化氧化合成苯甲醛,研究了反应条件对转化率和选择性的影响。结果表明,Ag/SBA-15具有均一的一维孔道结构、较厚的孔壁（3-5 nm）及较大的比表面积（411-541 m²/g）,其规整纳米空间的限域作用使一定负载量的Ag以纳米尺寸均匀分散于介孔SBA-15孔道内,增加了活性组分的比表面积。亲核性氧物种从Ag到SBA-15表面的氧溢流,提高了低温下Ag/SBA-15对苯甲醇气相选择性氧化合成苯甲醛的催化性能。5.3% Ag/SBA-15中的Ag粒径为5-6 nm,且均匀分散于载体孔道中,反应温度为220℃时,苯甲醇转化率为87%,苯甲醛选择性为95%;240℃时,苯甲醇转化率和苯甲醛选择性分别高达94%和97%;并在240-300℃范围内,其催化活性和选择性保持不变,表现出了良好的温度耐受能力。催化剂经活化再生可以连续使用40 h,选择性基本保持不变。     

Al~(3+)离子介入提升(NH_4)_2SiF_6对SBA-15介孔材料的水热稳定化作用（英文）

提出了一种(NH4)2Si F6处理提高SBA-15介孔材料水热稳定性的改良方法.采用SBA-15介孔材料中预引入Al3+离子,再进行1%SiO 2计量的(NH4)2Si F6处理,最后用强酸洗脱预引入的Al3+.结果显示,由此处理的SBA-15材料,其水热稳定性明显优于相同条件下未预引入Al3+时(NH4)2Si F6处理的样品.两者在800°C、100%水蒸气处理12 h后,虽然均能很好保持其介观有序度、形貌及六方孔道结构,但前者的比表面积可高达271 m2/g,而后者仅为224 m2/g.表明Al3+离子介入能大幅度提升(NH4)2Si F6处理对SBA-15介孔材料的稳定化作用.这主要得益于预引入的骨架Al3+在保障(NH4)2Si F6处理修复SBA-15材料表面缺陷和进行表面疏水化、提升其水热稳定性的同时,能减缓(NH4)2Si F6释放的多余F离子对SBA-15材料骨架的刻蚀破坏作用.Al3+离子介入的这种提升作用与其引入方式和SBA-15材料所经受的温度密切相关.     

Rapid synthesis of SBA-15 rods with variable lengths, widths, and tunable large pores

Dispersed SBA-15 rods have been synthesized with varying lengths, widths, and pore sizes in a low-temperature synthesis in the presence of heptane and NH(4)F. The pore size of the material can systematically be varied between 11 and 17 nm using different hydrothermal treatment times and/or temperatures. The particle length (400-600 nm) and width (100-400 nm) were tuned by varying the HCl concentration. All the synthesized materials possess a large surface area of 400-600 m(2)/g and a pore volume of 1.05-1.30 cm(3). A mechanism for the effect of the HCl concentration on the particle morphology is suggested. Furthermore, it is shown that the reaction time can be decreased to 1 h, with well-retained pore size and morphology. This work has resulted in SBA-15 rods with the largest pore size reported for this morphology.     

Novel modified nanoporous silica for oral drug delivery: loading and release of clarithromycin

Nanoporous silica SBA-15 was prepared to evaluate its application as an oral drug delivery system. A series of surface-functionalized nanopore materials as efficient clarithromycin delivery carriers was investigated. An efficient pH-responsive carrier system was constructed by hydrogen bond interaction between carboxyl and hydroxyl groups in the clarithromycin and the amine group in modified SBA-15. HPLC analyses of clarithromycin were run on a C₁₈ column using a mobile phase comprised of potassium dihydrogen phosphate, acetonitrile and methanol (30:40:30, v/v/v). Active molecules such as clarithromycin could be stored and released from the pore voids of SBA-15 by changing the pH. The amount of clarithromycin stored in the pores of nanoporous silica based on TREN [tris(2-aminoethyl) amine]-modified SBA-15 rods was up to 46 ± 4.8 wt% at pH 8. In addition, when the pH was below 4, clarithromycin was steadily released from the pores of SBA-15 (up to 97 wt% in simulated gastric medium).     

SBA-15负载CeO2纳米晶的溶胶-凝胶一步合成

以P123为模板剂, 正硅酸乙酯和硝酸铈为前驱体, 通过溶胶-凝胶路线在酸性条件下合成了SBA-15负载氧化铈(CeO2与SiO2质量比为28.7%)有序介孔材料. 采用热重/差热分析(TGA/DTA)、X射线衍射(XRD)、透射电镜(TEM)和氮气吸附等手段对所合成材料进行了表征. 结果表明, 合成的材料具有类似于SBA-15的结构, 孔径、孔容和比表面积分别为38.7 Å, 0.46 cm3/g和570 m2/g. X射线衍射(XRD)、透射电镜(TEM)、X射线能谱(EDS)和选区电子衍射花样联合表征证实了铈物种以高分散的CeO2纳米晶的形式分布在介孔基体中.     

Methane sorption in ordered mesoporous silica SBA-15 in the presence of water

Methane or natural gas is a practical alternative fuel of vehicles. To develop more efficient technology of on-board storage, a possibility of using SBA-15 as the methane carrier is tested. An ordered mesoporous silica molecular sieve SBA-15 is synthesized aimed at collecting the data of methane sorption in the presence of water. The synthesized material is examined with SEM, TEM, and XRD analyses, and the hexagonal channel structure is confirmed. Its textual parameters are evaluated on the basis of the adsorption data for nitrogen at 77 K, and it gives the results of 802 m2/g for the specific surface area, 1.31 cm3/g for the pore volume, a narrow pore size distribution centered at 7.7 nm, and 4 nm for the width of the partition wall. Methane sorption isotherms on SBA-15 are collected with a volumetric method for samples of different contents of water, and the enhancement of the sorption capacity due to the presence of water is observed. A discussion on the mechanism of the sorption enhancement is presented.     

Mapping the location of grafted PNIPAAM in mesoporous SBA-15 silica using gas adsorption analysis

The thermoresponsive polymer poly-N-isopropylacrylamide (PNIPAAM) was grafted in mesoporous SBA-15 silica. The grafting process consists of three steps: (i) increasing the amount of surface silanol groups of SBA-15 by hydroxylation, (ii) attachment of an anchor (1-(trichlorosilyl)-2-(m/p-(chloromethylphenyl)ethane) and finally (iii) the polymerization of the monomers (NIPAAM) onto the anchor. After each step, the materials were characterized regarding the porosity, using inert gas (argon, nitrogen) physisorption measurements. Also, the structure was investigated by small-angle X-ray diffraction analysis and thermogravimetric analysis was used for determination of the amount of grafted material. A total of 17% by weight of organic material was introduced in the porous host and the structure was preserved during the grafting process. Physisorption measurements revealed that the anchor is mainly located in the intrawall pores present in SBA-15. Consequently, the polymer is preferentially located in the intrawall pores or in the vicinity thereof. The final mesopore volume is 0.47 cm(3) g(-1) as compared to 0.96 cm(3) g(-1) for the pure SBA-15. The surprisingly large loss of mesopore volume and an almost constant mesopore diameter is consistent with a partial sealing of the mesopore volume in the composite materials. The potential thermocontrol combined with the large mesoporosity and the possible "storage space" provided by the sealed mesopore volume leads to a material with possibilities for various applications.     

Controlled drug release from bifunctionalized mesoporous silica

Serial of trimethylsilyl-carboxyl bifunctionalized SBA-15 (TMS/COOH/SBA-15) have been studied as carriers for controlled release of drug famotidine (Famo). To load Famo with large capacity, SBA-15 with high content of carboxyl groups was successfully synthesized by one-pot synthesis under the assistance of KCl. The mesostructure of carboxyl functionalized SBA-15 (COOH/SBA-15) could still be kept even though the content of carboxyl groups was up to 57.2%. Increasing carboxyl content could effectively enhance the loading capacity of Famo. Compared with pure SBA-15, into which Famo could be hardly adsorbed, the largest drug loading capacity of COOH/SBA-15 could achieve 396.9 mg/g. The release of Famo from mesoporous silica was studied in simulated intestine fluid (SIF, pH=7.4). For COOH/SBA-15, the release rate of Famo decreased with narrowing pore size. After grafting TMS groups on the surface of COOH/SBA-15 with hexamethyldisilazane, the release of Famo was greatly delayed with the increasing content of TMS groups.     

Simple synthesis route to monodispersed SBA-15 silica rods

A simple, flexible, reproducible, high-yielding (ca. 100%) synthesis of hexagonally facetted SBA-15 straight rods with uniform sizes (ca. 1.5 x 0.4 mum) under static conditions without using inorganic salts is provided. This method affords rodlike particles with temperature-dependent pore sizes ranging from 5.8 to 12.5 nm but with similar external dimensions. This work shows that in order to prepare short monodispersed SBA-15 rods, (i) the absence of stirring is essential, (ii) the temperature of the first stage should not exceed 60 degrees C, and (iii) addition of inorganic salts is not required.     

Study on the adsorption of lanthanum ion imprinted on SBA-15/Y

The lanthanum ion imprinted polymer (La-IIP/SBA-15/Y) was successfully synthesized by the surface ion imprinting method. Using La-IIP/SBA-15/Y as the adsorbent to adsorb lanthanum ions, the overall empirical conditions were optimized, and the best exploratory conditions were finally found. The pH of the solution was 2; the adsorption equilibrium was reached in 60 min and the saturated adsorption capacity was 562.95 mg/g La-IIP/SBA-15/Y adsorbed gadolinium ions in the study of its adsorption process and found that it conforms to the Langmuir isotherm adsorption model, and the adsorption reaction is a spontaneous reaction, and it also conforms to the quasi-second-order kinetic model. The selectivity of the adsorbent was explored experimentally, and the results showed that La-IIP/SBA-15/Y has good selectivity, and experimental elution and regeneration performance. The best elution effect is 2 mol/L hydrochloric acid. La-IIP/SBA-15/Y has good stability and can be reused.