Characterization of partially inverse spinel ZnFe2O4 with high saturation magnetization synthesized via soft mechanochemically assisted route

ZnFe₂O₄ was prepared by a soft mechanochemical route from two starting combinations of powders: (1) Zn(OH)₂/α-Fe₂O₃ and (2) Zn(OH)₂/Fe(OH)₃ mixed in a planetary ball mill. The mechanochemical treatment provoked reaction leading to the formation of the ZnFe₂O₄ spinel phase that was monitored by XRD, TEM, IR and Raman spectroscopy. The spinel phase was first observed after 4 h of milling and its formation was completed after 18 h in both the cases of starting precursors. The synthesized ZnFe₂O₄ has a nanocrystalline structure with a crystallite size of about 20.3 and 17.6 nm, for the cases (1) and (2), respectively. In the far-infrared reflectivity spectra are seen four active modes. Raman spectra suggest an existence of mixed spinel structure in the obtained nanosamples. In order to confirm phase formation and cation arrangement, Mössbauer measurements were done. Estimated degree of inversion is about 0.58 for both starting mixtures. The magnetic properties of the prepared ZnFe₂O₄ powders were also studied. The results show that the samples have a typical superparamagnetic-like behavior at room temperature. Higher values of magnetization in the case of samples obtained with starting mixture (2) suggest somewhat higher degree of cation inversion.     

Third order optical nonlinearities in ZnFe2O4 nanocrystals

Using Z-scan method with picosecond laser at 532 nm, the third order optical nonlinearities of ZnFe₂O₄ were investigated. The nonlinear refractive index is positive for all ZnFe₂O₄ samples and decrease with the nanocrystal size. The nonlinear absorption dominated by saturable absorption for 19 nm and 11 nm ZnFe₂O₄ but by two photon absorption for 5 nm ZnFe₂O₄ organosol. Origin of the optical nonlinearities and the size effect has been discussed.     

Effect of size and synthesis route on the magnetic properties of chemically prepared nanosize ZnFe2O4

Magnetization of the ZnFe₂O₄ sample of average size 4 nm measured with SQUID in the temperature range 5–300 K shows anomalous behaviour in field cooled (FC) and zero-field-cooled (ZFC) conditions. The FC and ZFC curves measured in 50 Oe field cross each other a little before the peaks. No such anomaly is observed with samples of 6 nm particle size made with the same procedure. The characteristics of the FC and ZFC curves are very different in ZnFe₂O₄ samples of the same size (6 nm) made via two different chemical routes. The genesis of these differences are suggested to be in cationic configuration and spin disorder. Fe-extended X-ray absorption fine structure (EXAFS) studies show that there is around 80% inversion in case of zinc ferrite (ZnFe₂O₄) with the particle size 4 nm, whereas ZnFe₂O₄ of size 6 nm shows 40% inversion. The samples with an average particle size of 7 nm and more show negligible inversion. Theoretical simulations suggest that the electrostatic energy of the system plays a crucial role in deciding the cationic configuration of spinel ferrites.     

Visible luminescence of Al2O3 nanoparticles embedded in silica glass host matrix

This paper deals with the sol-gel elaboration and defects photoluminescence (PL) examination of Al₂O₃ nanocrystallites (size ∼30 nm) confined in glass based on silica aerogel. Aluminium oxide aerogels were synthesized using esterification reaction for hydrolysis of the precursor and supercritical conditions of ethyl alcohol for drying. The obtained nanopowder was incorporated in SiO₂ host matrix. After heating under natural atmosphere at 1150 °C for 2 h, the composite Al₂O₃/SiO₂ (AS) exhibited a strong PL bands at 400-600 and 700-900 nm in 78-300 K temperature range. PL excitation (PLE) measurements show different origins of the emission. It was suggested that OH-related radiative centres and non-bridging oxygen hole centres (NBOHCs) were responsible for the bands at 400-600 and 700-900 nm, respectively.     

Magnetic properties of ZnFe2O4 nanoparticles produced by a low-temperature solid-state reaction method

ZnFe₂O₄ nanoparticles with average grain size ranging from 40 to 60 nm behaving superparamagnetic at room temperature have been produced using a low-temperature solid-state reaction (LTSSR) method without ball-milling process. Abnormal magnetic properties such as S-shape hysteresis loops and non-zero magnetic moments were observed. ZnFe₂O₄ nanoparticles were also synthesized using a NaOH coprecipitation method and a PVA sol-gel method to study the relationship between the preparation processes and the magnetic properties. Spin-glass behavior was observed in the low temperature solid-state reaction produced Zn ferrite in the zero-field cooled (ZFC) measurement. Our work proves that the various preparation methods will to some extent determine the properties of magnetic nanoparticles.     

Synthesis,photophysical properties,and photocatalytic applications of Bi doped NaTaO3 and Bi doped Na2Ta2O6 nanoparticles

Phase formation and photophysical properties of bismuth doped sodium tantalum oxide (perovskite, defect pyrochlore) nanoparticles prepared by a hydrothermal method were studied in detail. It was revealed that the synthesis conditions like NaOH concentration and bismuth precursor (NaBiO₃·2H₂O) markedly affect the crystal structure of sodium tantalum oxide. At low NaOH concentration and high bismuth precursor (NaBiO₃·2H₂O) content, Bi doped Na₂Ta₂O₆ (defect pyrochlore) phase was predominantly formed, while at higher NaOH concentration, Bi doped NaTaO₃ (perovskite) phase was formed. It was observed that the defect pyrochlore (Bi doped Na₂Ta₂O₆) phase was formed and stabilized by the presence of dopant precursor (NaBiO₃·2H₂O). The chemical analysis of the samples confirmed the doping of Bi³⁺ cations in both phases. Doping of bismuth enabled visible light absorption up to 500 nm in perovskite and defect pyrochlore type sodium tantalum oxide. Bi doped NaTaO₃ samples showed better performance for the photocatalytic degradation of rhodamine B than that of Bi doped Na₂Ta₂O₆, under visible light irritation (λ>420 nm). The present results shed light on phase formation of sodium tantalate and these results are useful in understanding properties of NaTaO₃ based compounds, synthesized by the hydrothermal method.     

Preparation of ferromagnetic γ - Fe2O3 nanocrystallites by oxidative co-decomposition of PEG 6000 and ferrocene

Highly crystalline and ferromagnetic γ-Fe₂O₃ nanocrystallites were prepared by controlled oxidative co-decomposition of PEG 6000 and ferrocene at a temperature of 450 ^°C under air atmosphere. The morphology, crystalline structure and preliminary magnetic properties of the as-synthesized nanocrystallites have been characterized by using transmission electron microscope (TEM), X-ray powder diffraction (XRD) and vibrating sample magnetometer (VSM). The highly crystalline γ-Fe₂O₃ nanocrystallites are in quasi-cubic shape with an average size of 30 nm and exhibit room-temperature ferromagnetism. The capping effect of PEG 6000 has also been investigated by thermogravimetry analysis (TGA) and Fourier transform infrared (FTIR) regarding controlling the size of the nanocrystallites and preventing the volatilization of ferrocene and thus raising the yield of the products. This simple method has a high yield of over 80% as well as low cost.     

Synthesis of ZnFe2O4 nanomagnets by Fe-ion implantation into ZnO and post-annealing

Fe ions of dose 8 × 10¹⁶ cm^-2 are implanted into a ZnO single crystal at 180 keV. Annealing at 1073 K leads to the formation of zinc ferrite (ZnFe₂O₄), which is verified by synchrotron radiation X-ray diffraction (SR-XRD) and X-ray photoelectron spectroscopy (XPS). The crystallographically oriented ZnFe₂O₄ is formed inside the ZnO with the orientation relationship of ZnFe₂O₄ (111)//ZnO (0001). Superconducting quantum interference device (SQUID) measurements show that the as-implanted and post-annealing samples are both ferromagnetic at 5 K. The synthesized ZnFe₂O₄ is superparamagnetic, with a blocking temperature (T_B = 25 K), indicated by zero field cooling and field cooling (ZFC/FC) measurements.     

Enhanced magnetization and ferrimagnetic behavior of normal spinel ZnFe2O4 thin film irradiated with femtosecond laser

We report on spatially selective change of magnetism from paramagnetic to ferrimagnetic-like behaviors in normal spinel ZnFe₂O₄ thin film under irradiation with 780 nm femtosecond laser pulses. The distribution of Zn²⁺ and Fe³⁺ ions in the irradiated region on the film surface becomes disordered because of local heating to high temperatures, and the metastable phase of ZnFe₂O₄ is frozen in by the rapid quenching after irradiation, resulting in the formation of the ferrimagnetic phase. The ferrimagnetic phase reverts to the paramagnetic state by annealing at 800°C. The present technique is useful for two-dimensional patterning of magnetic thin films.     

High pressure Raman spectroscopy of spinel-type ferrite ZnFe2O4

An in-situ Raman spectroscopic study was conducted to explore the pressure induced phase transformation of spinel-type ferrite ZnFe₂O₄. Results indicate that ferrite ZnFe₂O₄ initially transforms to an orthorhombic structure phase (CaFe₂O₄-polymorph) at a pressure of 24.6 GPa. Such a phase transformation is complete at 34.2 GPa, and continuously remains stable to the peak pressure of 61.9 GPa. The coexistence of the two phases over a wide range of pressure implies a sluggish mechanism upon the spinel-to-orthorhombic phase transition. Upon release of pressure, the high pressure ZnFe₂O₄ polymorph is quenchable at ambient conditions.     

The structure and magnetic properties of Zn1−xNixFe2O4 ferrite nanoparticles prepared by sol–gel auto-combustion

Zn_1−xNi_xFe₂O₄ ferrite nanoparticles were prepared by sol–gel auto-combustion and then annealed at 700 °C for 4 h. The results of differential thermal analysis indicate that the thermal decomposition temperature is about 210 °C and Ni–Zn ferrite nanoparticles could be synthesized in the self-propagating combustion process. The microstructure and magnetic properties were investigated by means of X-ray diffraction, scanning electron microscope, and Vibrating sample magnetometer. It is observed that all the spherical nanoparticles with an average grain size of about 35 nm are of pure spinel cubic structure. The crystal lattice constant declines gradually with increasing x from 0.8435 nm (x=0.20) to 0.8352 nm (x=1.00). Different from the composition of Zn_0.5Ni_0.5Fe₂O₄ for the bulk, the maximum M_s is found in the composition of Zn_0.3Ni_0.7Fe₂O₄ for nanoparticles. The H_c of samples is much larger than the bulk ferrites and increases with the enlarging x. The results of Zn_0.3Ni_0.7Fe₂O₄ annealed at different temperatures indicate that the maximum M_s (83.2 emu/g) appears in the sample annealed at 900 °C. The H_c of Zn_0.3Ni_0.7Fe₂O₄ firstly increases slightly as the grain size increases, and presents a maximum value of 115 Oe when the grains grow up to about 30 nm, and then declines rapidly with the grains further growing. The critical diameter (under the critical diameter, the grain is of single domain) of Zn_0.3Ni_0.7Fe₂O₄ nanoparticles is found to be about 30 nm.     

Quantum confinement effects of CdTe nanocrystals sequestered in TiO2 matrix: effect of oxygen incorporation

Thin films of TiO₂ with high volume fraction (40–55%) and crystallite size (6–40 nm) of CdTe nanoparticles had been prepared by rf magnetron sputtering from a composite TiO₂:CdTe target at room temperature and 373 K. A detailed optical properties of nanocrystalline CdTe:TiO₂ films as-deposited and after thermal treatment (300 °C) are studied. The absorbance of the TiO₂ films with CdTe nanocrystallite dispersions depends both on the nanocrystallite size and volume fraction. The blue-shifts of the optical absorption edge concurrent with the CdTe nanocystal size reduction for as-deposited and after thermal treatment of nanocrystalline CdTe:TiO₂ thin films with respect to the bulk semiconductor agrees quite well with the strong quantum confinement theory. A slight deviation in absorption edge values than the predicted values from the strong quantum confinement model can be attributed to change in interplanar distance due to oxygen incorporation and inhomogeneous size distribution of CdTe nanocrystallites in these films.     

Magnetoelectric characterization of xNi0.75Co0.25Fe2O4-(1−x)BiFeO3 nanocomposites

Magnetoelectric (ME) nanocomposites containing Ni_0.75Co_0.25Fe₂O₄-BiFeO₃ phases were prepared by citrate sol-gel process. X-ray diffraction (XRD) analysis showed phase formation of xNi_0.75Co_0.25Fe₂O₄-(1−x)BiFeO₃ (x=0.1, 0.2, 0.3 and 0.4) composites on heating at 700 °C. Transmission electron microscopy revealed the formation of powders of nano order size and the crystal size was found to vary from 30 to 85 nm. Dispersion in dielectric constant (ε) and dielectric loss (tan δ) in the low-frequency range have been observed. It is seen that nanocomposites exhibit strong magnetic properties and a large ME effect. On increasing Ni_0.75Co_0.25Fe₂O₄ contents in the nanocomposites, the saturation magnetization (M_S) and coercivity (H_C) increased after annealing at 700 °C. The large ME output in the nanocomposites exhibits strong dependence on magnetic bias and magnetic field frequency. The large value of ME output can be attributed to small grain size of ferrite phase of nanocomposite being prepared by citrate precursor process.     

Synthesis of Ni-doped InTaO4 nanocrystallites by reactive pulsed laser ablation for application to visible-light-operating photocatalysts

Ni-doped InTaO₄ nanocrystallites were synthesized by a reactive pulsed laser ablation process, aiming at visible-light-operating photocatalysts. The third harmonics beam of a Nd:YAG laser was focused onto a sintered In_0.9Ni_0.1TaO_4−δ target in mixture background gases (O₂ + He). The deposited species were columnar-structured porous films consisting of primary nanocrystallites. The mean diameter of the primary nanocrystallites was 4 nm. Optical absorption characteristics, especially in low absorbance (sub-band) regions, were evaluated by photoacoustic spectroscopy. Absorption in the sub-band region decreased drastically with increasing O₂ partial pressures. It is inferred that oxygen deficiencies are suppressed, because of enough oxygen vapors in the reactive background gases. An absorption band around 420 nm appeared obviously in O₂ partial pressures above 5%, in the Ni-doped InTaO₄ nanocrystallites. The visible region absorption band is presumably attributed to the Ni 3d-eg orbitals. In contrast, pure InTaO₄ nanocrystallites showed a sharp band edge, without the visible absorption band.     

An optimal low-temperature tartrate precursor method for the synthesis of monophasic nanosized ZnFe2O4

In this study, the synthesis of monophasic nanocrystalline zinc ferrite (ZnFe₂O₄) was achieved by controlling the thermal decomposition conditions of a zinc–iron tartrate precursor method. Differential thermal analysis/thermogravimetry (DTA/TG), X-ray diffraction (XRD), Fe²⁺ content analysis, transmission electron microscopy (TEM), and Brunauer-Emmett-Teller (BET) techniques were used to investigate the effect of heat treatment conditions on the calcined powders. The thermal decomposition of the precursor led to an intermediate phase formation of ZnO, Fe₃O₄, and γ-Fe₂O₃. It was found that the Fe₃O₄ → γ-Fe₂O₃ oxidation reaction is the key step in producing monophasic nanosized ZnFe₂O₄. The monophasic nanoparticles of ZnFe₂O₄ can be obtained when the precursor is heat treated under a low temperature (300–400 °C) and long residence time (4 h) process that can prompt the Fe₃O₄ oxidation and prevent the formation of α-Fe₂O₃.     

Biocompatibility of various ferrite nanoparticles evaluated by in vitro cytotoxicity assays using HeLa cells

Magnetic nanoparticles for thermotherapy must be biocompatible and possess high thermal efficiency as heating elements. The biocompatibility of Fe₃O₄ (20-30 nm), ZnFe₂O₄ (15-30 nm) and NiFe₂O₄ (20-30 nm) nanoparticles was studied using a cytotoxicity colony formation assay and a cell viability assay. The Fe₃O₄ sample was found to be biocompatible on HeLa cells. While ZnFe₂O₄ and NiFe₂O₄ were non-toxic at low concentrations, HeLa cells exhibited cytotoxic effects when exposed to concentrations of 100 μg/ml nanoparticles.     

Nanocrystallite formation in Pd capped PrH3−δ films

Restricting the palladium cap layer thickness to ≤9 nm on top of 170 nm Pr films during in situ hydrogen loading has been shown to result in nanocrystallite size PrH_3−δ films even though the deposited Pr films are of large crystallite size. The effect is attributed to hydrogen-induced stresses in the PrH_3−δ films, which trigger structural rearrangement. These nanocrystalline films show a blue shift of the transmittance edge with respect to PrH_3−δ films of large crystallite size. The approximate size of the nanocrystallites calculated from the blue shift using an effective mass approximation (EMA) theory is supported by XRD, TEM and AFM measurements.     

Preparation and properties of disordered NaBi(XO4)2, X=W or Mo, crystals doped with rare earths

NaBi_1−xRE_x(XO₄)₂, X=W or Mo and RE=Pr, Nd, Ho, Er and Yb single crystals have been grown by the Czochralski technique. Rare earth concentrations about 3.5×10²⁰ cm⁻³ have been achieved in crystals with good optical quality. Melt stability is obtained by synthesising NaBi(XO₄)₂ from the precursor Na₂X₄O₁₃ phase and minimising Mo volatility. The strength of W and Mo compounds to chemical attack and thermal annealing in several atmospheres is reported. Mo compound is etched by inorganic acids and becomes coloured after vacuum annealing. The optical absorption, photoluminescence and refractive indices of the hosts are characterised and show a dichroic character. The lattice disorder induces broadening of the 10 K optical absorption of the rare earth impurities.     

Bismuth zinc niobate (Bi1.5ZnNb1.5O7) ceramics derived from metallo-organic decomposition precursor solution

The preparation, microstructure development and dielectric properties of Bi_1.5ZnNb_1.5O₇ pyrochlore ceramics by metallo-organic decomposition (MOD) route are reported. Homogeneous precalcined ceramic powders of 13-36 nm crystallite size were obtained at temperatures ranging from 500 to 700 °C. The thermal decomposition/oxidation of the gelled precursor solution was chemically analyzed, TG/DTA, XRD, and SEM, led to the formation of a pure cubic pyrochlore phase with a stoichiometry close to Bi_1.5ZnNb_1.5O₇ which begins to form at 500 °C. The metallo-organic precursor synthesis method, where Bi, Zn and Nb ions are chelated to form metal complexes, allows the control of Bi/Zn/Nb stoichiometric ratio on a molecular scale leading to the rapid formation of bismuth zinc niobate (Bi_1.5ZnNb_1.5O₇) ceramic fine powders with pure pyrochlore structure. The powders were pressed into pellets and can be sintered at temperatures as low as 800-1000 °C. Fine crystalline ceramics with the grain size in the range of 200-500 nm have been obtained at the sintering temperature of 800 °C. The dielectric properties in high frequency to microwave range were measured and discussed.     

Magnetization anomalies of nanosize zinc ferrite particles prepared using electrodeposition

Nanosize zinc ferrite particles have been prepared for the first time using electrodeposition. Zinc and iron are deposited on the cathode from a common bath containing the salts of zinc and iron. The deposited materials were forced to undergo electrochemical oxidation in a strong alkaline solution (1 M KOH) to convert them into oxides. Crystallization in ZnFe₂O₄ structure was obtained by heating the deposited material at appropriate temperature. X-ray diffraction pattern confirmed that the procedure leads to the formation of pure phase of ZnFe₂O₄. The magnetization value for the smallest size ZnFe₂O₄ is much smaller than that for the ZnFe₂O₄ made by most of the other methods although it shows a nice hysteresis shape. The magnetization shows very little variation with size in the range studied.