Multicomponent Adsorption of Pesticides onto Activated Carbon Fibers

The adsorption equilibria of pesticides and metabolites (atrazine, deethylatrazine, deisopropylatrazine and simazine) are studied onto activated carbon fibers –ACF– with a broad pore size distribution (32% mesopore volume, 68% micropore volume). Mono-and multi-component isotherms have been determined for low concentrations, from 0.23×10⁻⁶ to 9.52×10⁻⁶ mol L⁻¹. Single solute isotherms, modeled by Freundlich and Langmuir models, tend to prove the influence of the adsorbate's solubility in the adsorption capacity of activated carbon fibers. Binary solute isotherms confirm the strong influence of pesticide solubility on the competitive adsorption mechanism: the competition is higher in the case of adsorbates of different solubilities (atrazine and DEA or DIA for example). Multicomponent experimental data were modeled by extended Langmuir-based equations and the Ideal Adsorbed Solution theory. Whereas the first ones failed to model accurately binary adsorption due to restrictive hypothesis, the IAS model showed a good agreement between experimental and predicted data. It emphasised also the difficulty in satisfying the hypothesis of the model in the case of highly adsorbed compounds. Finally, the simultaneous adsorption of atrazine and NOM (in a natural water, DOC = 18.2 mg L⁻¹) shows no adsorption competition effects between natural organic matter and atrazine. This is due to the presence of secondary micropores (0.8–2 nm) and mesopores in the ACF, which limit a pore blockage phenomenon by NOM.     

Determination and Pharmacokinetic Study of Calycosin-7-O-β-d-glucoside in Rat Plasma After Intravenous Administration of Aidi Lyophilizer

Aidi injection is a clinical medicine used in China for the treatment of cancer. Calycosin-7-O-β-d-glucoside is the main effective components of the formulas. In this study, a high performance liquid chromatographic (LC) method was developed to quantify calycosin-7-O-β-d-glucoside in rat plasma using a liquid–liquid extraction and ultraviolet (UV) absorbance detection. LC analysis was performed on a Diamonsil C₁₈ column (200 × 4.6 mm i.d., 5 μm particle size) with isocratic mobile phase consisting of acetonitrile–0.05% phosphoric acid (19.5:80.5, v/v) of a flow rate of 1.0 mL min⁻¹. The linear range was 0.11–17.6 μg mL⁻¹ and the low quantification limit was 0.11 μg mL⁻¹ (S/N = 10). The intra- and inter-day relative standard deviations (RSD) in the measurement of quality control (QC) samples 0.11, 0.22, 1.32 and 8.80 μg mL⁻¹ ranged from 4.1 to 6.3 and 4.3 to 6.2%, respectively. The accuracy was from −6.7 to 4.3% in terms of relative error (RE). Calycosin-7-O-β-d-glucoside was stable in storage at −20 °C for 2 weeks and stable after three freeze–thaw cycles in rat plasma. This method was validated for specificity, accuracy, precision and was successfully applied to pharmacokinetic study of calycosin-7-O-β-d-glucoside in rat plasma after intravenous administration of Aidi lyophilizer.     

Analytical method for assessing potential dermal exposure to pesticides of a non-agricultural occupationally exposed population

To measure dermal exposure of a non-agricultural occupationally exposed population to pesticides, a new method has been developed for analysis of 13 pesticides from different classes (fungicides, herbicides, insecticides) on dermal patches. The method includes extraction of the patches and analysis of the pesticides by GC–MS and/or HPLC–fluorescence. Water-soluble pesticides (glyphosate and glufosinate) on patches were ultrasonically extracted twice with ultra-pure water for 10 min and analysed by HPLC–fluorescence after derivatisation with FMOC. Organic-soluble pesticides (bifenthrin, cyprodinil, difufenicanil, fludioxonil, oxadiazon, pyriproxyfen, clopyralid, 2,4-D, fluroxypyr, 2,4-MCPA, and triclopyr) were extracted ultrasonically twice for 10 min with 70:30 dichloromethane–acetonitrile and analysed by GC–MS directly or after derivatisation with N-methyl-N-tert-butyldimethylsilyltrifluoroacetamide. Detection limits varied between 3 and 4 μg L⁻¹ for water-soluble pesticides and between 1 and 10 μg L⁻¹ for organic-soluble pesticides.     

Characterization of a Thermostable Family 1 Glycosyl Hydrolase Enzyme from <Emphasis Type="Italic">Putranjiva roxburghii</Emphasis> Seeds

A 66-kDa thermostable family 1 Glycosyl Hydrolase (GH1) enzyme with β-glucosidase and β-galactosidase activities was purified to homogeneity from the seeds of Putranjiva roxburghii belonging to Euphorbiaceae family. N-terminal and partial internal amino acid sequences showed significant resemblance to plant GH1 enzymes. Kinetic studies showed that enzyme hydrolyzed p-nitrophenyl β-d-glucopyranoside (pNP-Glc) with higher efficiency (K _cat/K _m = 2.27 × 10⁴ M⁻¹ s⁻¹) as compared to p-nitrophenyl β-d-galactopyranoside (pNP-Gal; K _cat/K _m = 1.15 × 10⁴ M⁻¹ s⁻¹). The optimum pH for β-galactosidase activity was 4.8 and 4.4 in citrate phosphate and acetate buffers respectively, while for β-glucosidase it was 4.6 in both buffers. The activation energy was found to be 10.6 kcal/mol in the temperature range 30–65 °C. The enzyme showed maximum activity at 65 °C with half life of ~40 min and first-order rate constant of 0.0172 min⁻¹. Far-UV CD spectra of enzyme exhibited α, β pattern at room temperature at pH 8.0. This thermostable enzyme with dual specificity and higher catalytic efficiency can be utilized for different commercial applications.     

Determination of D-fagomine in buckwheat and mulberry by cation exchange HPLC/ESI-Q-MS

d-Fagomine is an iminosugar first found in buckwheat (Fagopyrum esculentum Moench) which if used as a dietary supplement or functional food component may reduce the risks of developing insulin resistance, becoming overweight and suffering from an excess of potentially pathogenic bacteria. As d-fagomine may become increasingly important to the food industry, a reliable analytical method for its determination in natural plant sources and foodstuffs is desirable. We have devised a method to separate d-fagomine from its diastereomers 3-epi-fagomine and 3,4-di-epi-fagomine in a single run by cation exchange high-performance liquid chromatography (HPLC) with detection and quantification by mass spectrometry using electrospray ionisation and a simple quadrupole analyser (ESI–Q-MS). The method is validated and applied to the determination of d-fagomine in buckwheat groats (6.7–44 mg kg⁻¹), leaves, bran and flour. We show that buckwheat contains 3,4-di-epi-fagomine (1.0–43 mg kg⁻¹), which has not previously been reported in this source. The procedure is also applied to mulberry (Morus alba) leaves, which contain d-fagomine and 3-epi-fagomine as minor components. The new method provides a means for convenient and accurate determination of d-fagomine in plant samples and foodstuffs.     

Sol–gel and impregnated prepared silver TiO<Subscript>2</Subscript> semiconductors as photocatalysts for the UV decomposition of 2,4-<Emphasis Type="SmallCaps">d</Emphasis>: a comparative study of the preparation method

UV-photocatalytic oxidation of 2,4-dichlorophenoxyacetic acid (2,4-d) was studied on Silver–TiO₂ semiconductors prepared by co-gelling silver acetylacetonate and titanium butoxide (TiO₂–Ag) or by incipient impregnation with silver acetylacetonate (0.5 wt% Ag) of bare TiO₂ sol–gel and TiO₂–P25 supports. The comparative study shows that only a slight modification on the specific surface area was obtained on the TiO₂–Ag sample (60 m²/g) as compared to the TiO₂ sol–gel bare support (65 m²/g). XRD patterns of the samples show anatase as the crystalline phase present in the sol–gel TiO₂ preparations. By means of HRTEM and HAADF-STEM electron microscopy techniques, silver nanoparticles (<12.0 nm) were identified which are very small to be detected by XRD. The photocatalytic oxidation of the herbicide 2,4-d used as a model of contaminant show for the kinetic parameter t_1/2 values of 45 min for the TiO₂–Ag sample, while for the impregnated Ag/TiO₂ and Ag/P25 nanomaterials t_1/2 was 124 and 66 min, respectively. The higher photoactivity of the TiO₂–Ag photocatalyst is attributed to a combined effect of the silver nanoparticles in interaction with the titania semiconductor.     

Analysis of priority pesticides and phenols in Portuguese river water by liquid chromatography-mass spectrometry

Summary The determination of selected pesticides and phenols in Portuguese river water samples was carried out from April to September, 1999. The method involved 200 mL samples taken by offline, solid phase extraction by OASIS polymeric cartridges followed by liquid chromatography-atmospheric pressure, chemical ionization-mass spectrometry (LC-APCI-MS). Recoveries of pesticides were 50–96% and 72–120% for the Platform and HP 1100 instruments, respectively. Chlorophenols gave recoveries of 60–91%. Triazines and transformation products like desethylatrazine (DEA) and desisopropylatrazine (DIA) and compounds such as diuron and chlorophenols were positively identified by LC-APCI-MS. The levels detected of the different compounds varied from 0.01–2.61 μg L⁻¹, the most frequently detected compounds being, atrazine, simazine, terbuthylazine, alachlor, metolachlor, Irgarol, diuron, 2,4,6-trichlorophenol, desisopropylatrazine and desethylatrazine.     

ABA- and BAB-triblock cooligomers of tri-<Emphasis Type="Italic">O</Emphasis>-methylated and unmodified cello-oligosaccharides: syntheses and structure-solubility relationship

Triblock cooligomers consisting of tri-O-methyl-glucopyranosyl and unmodified glucopyranosyl residues, methyl 2,3,4,6-tetra-O-methyl-β-d-glucopyranosyl-(1 → 4)-2,3,6-tri-O-methyl-β-d-glucopyranosyl-(1 → 4)-β-d-glucopyranosyl-(1 → 4)-β-d-glucopyranosyl-(1 → 4)-2,3,6-tri-O-methyl-β-d-glucopyranosyl-(1 → 4)-2,3,6-tri-O-methyl-α-d-glucopyranoside (1: ABA triblock cooligomer; DS = 2.1) and β-d-glucopyranosyl-(1 → 4)-2,3,6-tri-O-methyl-β-d-glucopyranosyl-(1 → 4)-2,3,6-tri-O-methyl-β-d-glucopyranosyl-(1 → 4)-2,3,6-tri-O-methyl-β-d-glucopyranosyl-(1 → 4)-2,3,6-tri-O-methyl-β-d-glucopyranosyl-(1 → 4)-d-glucopyranose (2: BAB triblock cooligomer; DS = 1.8) were prepared. Compound 1 dissolved both in distilled water and chloroform but compound 2 dissolved in distilled water not in chloroform, though compounds 1 and 2 consist of 4 tri-O-methyl-glucopyranosyl and 2 unmodified anhydro glucopyranosyl units.     

Synthesis of blockwise alkylated tetrasaccharide–organic quantum dot complexes and their utilization for live cell labeling with low cytotoxicity

Bioimaging is a key to understanding immune responses, cell differentiation, and development. Quantum dots (QDs) conjugated with monoclonal antibodies and other biomolecules are currently utilized for flow cytometry and immunohistochemistry, but monoclonal antibody–QD complexes are of limited use when cell surface markers are not available. In this study, we synthesized novel amphiphilic blockwise alkylated tetrasaccharides and developed a simple method for labeling a wide variety of live cells with organic QDs encapsulated with these carbohydrates. The novel amphiphilic blockwise alkylated tetrasaccharides were as follows: methyl β-d-glucopyranosyl-(1 → 4)-β-d-glucopyranosyl-(1 → 4)-2,3,6-tri-O-methyl-β-d-glucopyranosyl-(1 → 4)-2,3,6-tri-O-methyl-d-glucopyranoside (1), methyl β-d-galactopyranosyl-(1 → 4)-β-d-glucopyranosyl-(1 → 4)-2,3,6-tri-O-methyl-β-d-glucopyranosyl-(1 → 4)-2,3,6-tri-O-methyl-d-glucopyranoside (2), ethyl β-d-glucopyranosyl-(1 → 4)-β-d-glucopyranosyl-(1 → 4)-2,3,6-tri-O-ethyl-β-d-glucopyranosyl-(1 → 4)-2,3,6-tri-O-ethyl-d-glucopyranoside, (3), and ethyl β-d-galactopyranosyl-(1 → 4)-β-d-glucopyranosyl-(1 → 4)-2,3,6-tri-O-ethyl-β-d-glucopyranosyl-(1 → 4)-2,3,6-tri-O-ethyl-d-glucopyranoside (4). The newly synthesized blockwise alkylated tetrasaccharides spontaneously assembled into micelle-like particles, in which the hydrophobic moiety of the blockwise alkylated tetrasaccharides played an important role. They were less toxic to human cells than octyl β-d-glucopyranoside, a commonly used amphiphilic glucoside. Flow cytometry and confocal laser scanning microscopy revealed that the blockwise alkylated tetrasaccharide–organic QD complexes were stably attached to live cells. The affinity of compounds 1 and 2 to the live cell surface was slightly higher than that of compounds 3 and 4. Because the preparation of these carbohydrate–QD complexes is simple and does not require sophisticated equipment, and because the complexes can be autonomously attached to a wide spectrum of cell lines, they can be used as cell labeling reagents in biomedical studies.     

Potentiometric determination of α-L-fucosidase enzyme by using 2-chloro-4-nitrophenol-rhodamine B ion pair chemical recognition in PVC membrane sensor

The activity of the α-l-fucosidase (AFU) enzyme represents an excellent test for diagnosis of hepatocellular carcinoma (HCC) and fucosidosis recognized in inborn disorder of metabolism and increases the sensitivity of detection to 95.5% in patients with HCC. Therefore, the determination of the activity of AFU enzyme is very important and can be used as a screening tool for the early diagnosis of tumors for HCC patients. A simple, accurate, and sensitive potentiometric method was developed for measuring the activity of AFU. The method was based upon measuring the concentration of 2-chloro-4-nitrophenol (2-chloro-4-NP) using a 2-chloro-4-NP-rhodamine B ion pair in a PVC membrane sensor. The electrode shows a linear, reproducible, and stable potentiometric response with an anionic Nernstian slope of −51.13 ± 0.6 mV/decade over a wide range of concentrations 10⁻⁵–10⁻² M and a detection limit of 1.0 × 10⁻⁶ M of 2-chloro-4-NP. The membrane exhibits a fast response time of 30 s, over a pH range of 4.0–6.5. The selectivity coefficients indicate excellent selectivity for 2-chloro-4-NP over a number of interfering species, e.g., chloride, nitrate, sulfate, chromate urea, albumin, glucose, uric acid, and total protein. The prepared sensor has been used successfully for the determination of 2-chloro-4-NP produced from the hydrolysis of 2-chloro-4-NP-α-l-fucopyranoside substrate. It was also applied for the determination α-l-fucosidase enzyme of 33 serum samples of healthy subjects and patients. The average recoveries ± RSD for the healthy subjects, cirrhosis of chronic hepatitis C and B, and HCC serum samples were 102.6 ± 1.01%, 101.5 ± 0.95%, and 100.1 ± 1.1%, respectively. The results obtained are in good agreement with those obtained by standard methods.     

Low-temperature thermodynamic properties of <Emphasis Type="SmallCaps">dl</Emphasis>-cysteine

Heat capacity C _p(T) of the crystalline dl-cysteine was measured on heating the system from 6 to 309 K by adiabatic calorimetry; thermodynamic functions were calculated based on these data smoothed in the temperature range 6–273.15 K. The values of heat capacity, entropy, and enthalpy at 273.15 K were equal to 142.4, 153.3, and 213.80 J K⁻¹ mol⁻¹, respectively. At about 300 K, a heat capacity peak was observed, which was interpreted as an evidence of a first-order phase transition. The enthalpy and the entropy of the transition are equal, respectively, to 2300 ± 50 and 7.6 ± 0.1 J K⁻¹ mol⁻¹.     

Multiresidue analysis of atrazine, diuron and their degradation products in sewage sludge by liquid chromatography tandem mass spectrometry

A multiresidue method has been developed to analyze atrazine (ATZ), diuron (DIU), and their major degradation products, desethylatrazine (DEA), desisopropylatrazine (DIA), and dichlorophenylmethylurea in sewage sludge. Liquid chromatography coupled to electrospray tandem mass spectrometry (LC–ESI-MS–MS) allowed, in the multiple-reaction monitoring mode, the simultaneous analysis of these pesticides in only one run after their extraction with ethyl acetate–dichloromethane 90:10 (v/v) and a cleanup on a Florisil column. Stable isotopically labeled ATZ and DIU were used as internal standards to overcome matrix effects during the pesticide quantification. Using fortified samples, the method gave rise to 86–115% as mean recovery values depending on the analyte. Limits of detection (LODs) and of quantification (LOQs) ranging from 0.3 (DIA) to 1.5 (DEA) μg kg⁻¹ dw and from 0.4 (DIA) to 2.0 (DEA) μg kg⁻¹ dw, respectively, were sufficient to achieve the monitoring of these molecules in sludge from wastewater treatment plants of the Ile-de-France region.     

New class of carbohydrate-based nonionic surfactants: diblock co-oligomers of tri-<Emphasis Type="Italic">O</Emphasis>-methylated and unmodified cello-oligosaccharides

Mixtures of diblock co-oligomers of tri-O-methylated and unmodified cello-oligosaccharides have been found to be amphiphilic, as reported before. In order to clarify their accurate amphiphilic property, diblock co-oligomers of tri-O-methylated and unmodified cello-oligosaccharides with monodispersity, methyl β-d-glucopyranosyl-(1→4)-2,3,6–tri-O-methyl-β-d-glucopyranosyl-(1→4)-2,3,6–tri-O-methyl-β-d-glucopyranosyl-(1→4)-2,3,6-tri-O-methyl-β-d-glucopyranosyl-(1→4)-2,3,6-tri-O-methyl-d-glucopyranoside (1, pentamer), methyl β-d-glucopyranosyl-(1→4)- β-d-glucopyranosyl-(1→4)-2,3,6-tri-O-methyl-β-d-glucopyranosyl-(1→4)-2,3,6-tri-O-methyl-β-d-glucopyranosyl-(1→4)-2,3,6-tri-O-methyl-β-d-glucopyranosyl-(1→4)-2,3,6-tri-O-methyl-d-glucopyranoside (2, hexamer), and methyl β-d-glucopyranosyl-(1→4)-2,3,6-tri-O-methyl-β-d-glucopyranosyl-(1→4)- 2,3,6-tri-O-methyl-d-glucopyranoside (3, trimer) were synthesized independently. These compounds had higher surface activities compared to the mixture of diblock co-oligomers of tri-O-methylated and unmodified cello-oligosaccharides and commercially available methylcellulose (MC) SM-4. This paper describes the methods of synthesis of these compounds, and the influence of amphiphilic character on their surface activity. A new class of carbohydrate-based nonionic surfactant without long alkyl chain was discovered.     

Production of <Emphasis Type="SmallCaps">d</Emphasis>-tagatose,a Functional Sweetener,Utilizing Alginate Immobilized <Emphasis Type="Italic">Lactobacillus fermentum</Emphasis> CGMCC2921 Cells

d-tagatose is a ketohexose that can be used as a novel functional sweetener in foods, beverages, and dietary supplements. This study was aimed at developing a high-yielding d-tagatose production process using alginate immobilized Lactobacillus fermentum CGMCC2921 cells. For the isomerization from d-galactose into d-tagatose, the immobilized cells showed optimum temperature and pH at 65 °C and 6.5, respectively. The alginate beads exhibited a good stability after glutaraldehyde treatment and retained 90% of the enzyme activity after eight cycles (192 h at 65 °C) of batch conversion. The addition of borate with a molar ratio of 1.0 to d-galactose led to a significant enhancement in the d-tagatose yield. Using commercial β-galactosidase and immobilized L. fermentum cells, d-tagatose was successfully obtained from lactose after a two-step biotransformation. The relatively high conversion rate and productivity from d-galactose to d-tagatose of 60% and 11.1 g l⁻¹ h⁻¹ were achieved in a packed-bed bioreactor. Moreover, lactobacilli have been approved as generally recognized as safe organisms, which makes this L. fermentum strain an attracting substitute for recombinant Escherichia coli cells among d-tagatose production progresses.     

Determination of viable <Emphasis Type="Italic">Escherichia coli</Emphasis> using antibody-coated paramagnetic beads with fluorescence detection

A rapid and convenient assay system was developed to detect viable Escherichia coli in water. The target bacteria were recovered from solution by immunomagnetic separation and incubated in tryptic soy broth with isopropyl-β-d-thiogalactopyranoside, which induces formation of β-galactosidase in viable bacteria. Lysozyme was used to lyse E. coli cells and release the β-galactosidase. β-Galactosidase converted 4-methylumbelliferyl-β-d-galactoside to 4-methylumbelliferone (4-MU), which was measured by fluorescence spectrophotometry using excitation and emission wavelengths of 355 and 460 nm, respectively. Calibration graphs of 4-MU fluorescence intensity versus E. coli concentration showed a detection range between 8 × 10⁴ and 1.6 × 10⁷ cfu mL⁻¹, with a total analysis time of less than 3 h. The advantage of this method is that it detects viable cells because it is based on the activity of the enzyme intrinsic to live E. coli.     

Enhanced Production of an Extracellular β-<Emphasis Type="SmallCaps">d</Emphasis>-Fructofuranosidase Fructohydrolase from a 2-Deoxy-<Emphasis Type="SmallCaps">d</Emphasis>-glucose Stabilized Mutant of <Emphasis Type="Italic">Candida utilis</Emphasis>

The enzyme β-d-fructofuranosidase fructohydrolase (FFH) cleaves the α-1,4 glycosidic linkage between α-d-glucose and β-d-fructose molecules of sucrose, releasing monosaccharides by hydrolysis. In the present study, FFH production in Candida utilis GC-46, a lipolytic wild yeast strain was improved by exposure to N-methyl N-nitro N-nitroso guanidine (NG) and 2-deoxy-d-glucose (2dg) at various levels. The mutant strain NG-5 was obtained after exposure to 0.06 mg/ml of NG for 20 min. NG-5 offers improved extracellular FFH production (34 ± 2.6 U/ml/min) when compared to the wild strain (1.15 ± 0.01 U/ml/min). A 40-fold increase of FFH (45.65 ± 2.0 U/ml/min) was achieved when the process parameters, including incubation period (48 h), sucrose concentration (5.0 g/l), initial pH (6.0), inoculum size (2.0% v/v, 16 h old), and urea concentration (0.2%, w/v) were identified using Plackett–Burman design. The kinetic parameters viz. Q _p (0.723 U/g/h), Y _p/s (2.036 U/g), and q _p (0.091 U/g yeast cells/h) indicate that NG-5 is a hyperproducer of extracellular FFH with a concomitant increase in growth rate. The volumetric productivity of NG-5 was over sixfold improved over the parental strain. The enzyme production improvement is highly significant (HS, LSD 0.042, p ≤ 0.05), indicating commercial utility.     

Mechanistic studies on the intramolecular electron transfer in an adduct species of the oxo-centred trinuclear iron(III) cation and <Emphasis Type="SmallCaps">l</Emphasis>-ascorbic acid in aqueous solution

The kinetics of the intra-molecular electron transfer of an adduct of l-ascorbic acid and the [Fe₃^IIIO(CH₃COO)₆(H₂O)₃]⁺ cation in aqueous acetate buffer was studied spectrophotometrically, over the ranges 2.55 ≤ pH ≤ 3.74, 20.0 ≤ θ ≤ 35.0 °C, at an ionic strength of 0.50 and 1.0 mol dm⁻³ (NaClO₄). The reaction of l-ascorbic acid and the complex cation involves the rapid formation of an adduct species followed by a slower reduction in the iron centres through consecutive one-electron transfer processes. The final product of the reaction is aqueous iron(II) in acetate buffer. The proposed mechanism involves the triaqua and diaqua-hydroxo species of the complex cation, both of which form adducts with l-ascorbic acid. At 25 °C, the equilibrium constant for the adduct formation was found to be 86 ± 15 and 5.8 ± 0.2 dm³ mol⁻¹ for the triaqua and diaqua-hydroxo species, respectively. The kinetic parameters derived from the rate expression have been found to be: k ₀ = (1.12 ± 0.02) × 10⁻² s⁻¹ for the combined spontaneous decomposition and k ₁ = (4.47 ± 0.06) × 10⁻² s⁻¹ (ΔH ₁^‡ = 51.0 ± 2.3 kJ mol⁻¹, ΔS ₁^‡ = −100 ± 8 J K⁻¹ mol⁻¹), k ₂ = (4.79 ± 0.38) × 10⁻¹ s⁻¹ (ΔH ₂^‡ = 76.5 ± 0.8 kJ mol⁻¹, ΔS ₂^‡ = 6 ± 3 J K⁻¹ mol⁻¹) for the triaqua and diaqua-hydoxo species, respectively.     

Mechanistic aspects of ligand substitution on <Emphasis Type="Italic">cis</Emphasis>-diaqua(<Emphasis Type="Italic">cis</Emphasis>-1,2-diaminocyclohexane)platinum(II) by Glycine-<Emphasis Type="SmallCaps">l</Emphasis>-Leucine

The kinetics of the interaction of glycine-l-leucine (Glyleu) with cis-[Pt(cis-dach)(OH₂)₂]²⁺ (dach = 1,2-diaminocyclohexane) has been studied spectrophotometrically as a function of [cis-[Pt(cis-dach)(OH₂)₂]²⁺], [Glyleu] and temperature at pH 4.0, where the complex exists predominantly as the diaqua species and Glyleu as a zwitterion. The substitution reaction shows two consecutive steps: the first is the ligand-assisted anation and the second is the chelation step. The activation parameters for both the steps were evaluated using Eyring’s equation. The low ∆H₁^≠ (51.9 ± 2.8 kJmol⁻¹) and large negative value of ∆S₁^≠ (−152 ± 8 JK⁻¹mol⁻¹) as well as ∆H₂^≠ (54.4 ± 1.7 kJmol⁻¹) and ∆S₂^≠ (−162 ± 5 JK⁻¹mol⁻¹) indicate an associative mode of activation for both the aqua ligand substitution processes.     

Β-d-Xylosidase from Selenomonas ruminantium: Catalyzed Reactions with Natural and Artificial Substrates

Catalytically efficient β-d-xylosidase from Selenomonas ruminantium (SXA) exhibits pK _as 5 and 7 (assigned to catalytic base, D14, and catalytic acid, E186) for k _cat/K _m with substrates 1,4-β-d-xylobiose (X2) and 1,4-β-d-xylotriose (X3). Catalytically inactive, dianionic SXA (D14⁻E186⁻) has threefold lower affinity than catalytically active, monoanionic SXA (D14⁻E186^H) for X2 and X3, whereas D14⁻E186⁻ has twofold higher affinity than D14⁻E186^H for 4-nitrophenyl-β-d-xylopyranoside (4NPX), and D14⁻E186⁻ has no affinity for 4-nitrophenyl-α-l-arabinofuranoside. Anomeric isomers, α-d-xylose and β-d-xylose, have similar affinity for SXA. 4-Nitrophenol competitively inhibits SXA-catalyzed hydrolysis of 4NPX. SXA steady-state kinetic parameters account for complete progress curves of SXA-catalyzed hydrolysis reactions. The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

Preparation of antibodies and development of a sensitive immunoassay with fluorescence detection for triazine herbicides

Specific polyclonal antibodies against s-triazine herbicides were obtained by preparing immunogens coupling home-synthesized haptens derivatives of simazine (6-chloro-N-ethyl-N′-ethyl-1,3,5-triazine-2,4-diamine) to lysine groups of hemocyanin from keyhole limpets and bovine serum albumin carrier proteins. Three highly sensitive rabbit antisera were obtained and evaluated with a battery of six enzyme tracers derived from triazine structures in an optimized ELISA format. The antiserum As8 and the HRP-2f tracer, which yield the best assay sensitivity for simazine (detection limit 0.11 ± 0.02 μg L⁻¹, IC₅₀ 0.88 ± 0.04 μg L⁻¹), were applied to the development of a sensitive flow-through immunoassay for the analysis of this herbicide. The automated assay was based on a direct competitive immunosorbent assay and fluorescence detection. The optimized method presents an IC₅₀ value of 0.35 ± 0.04 μg L⁻¹ with a detection limit of 1.3 ± 0.9 ng L⁻¹ and a dynamic range from 0.010 to 7.5 μg L⁻¹ simazine. The generic nature of the antiserum was shown by good relative cross-reactivities with other triazines such as atrazine (420%) or propazine (130%) and a lower response to terbutylazine (6.4%) and desethyl-atrazine (2.2%). No cross-reactivity was obtained for nonrelated pesticides such as 2,4-dichlorophenoxyacetic acid or linuron and the assay could be applied as a screening method for triazine herbicides. The total analysis time was 30 min per determination and the immunosensor could be reused for more than 150 cycles without significant loss of activity. The immunosensor has been successfully applied to the direct analysis of simazine in surface water samples at the nanogram per liter level. The results obtained by comparative analysis of the immunosensor with a chromatographic procedure for triazines showed a close correspondence.