纳米铁的低温热容和热力学性质研究

用扫描电子显微镜(SEM)测定了纳米铁试样的粒径, SEM结果表明Fe试样平均粒径d为25 nm. 在84～350 K温区, 用精密低温绝热量热计测定了该纳米铁试样的等压摩尔热容, 拟合出其等压摩尔热容与热力学温度的函数关系式: Cp=36.831+14.772x−5.4968x2−0.7099x3−1.3188x4, 其中x=(T−234)/156. 根据热容与热力学函数关系, 计算了以298.15 K为基准的纳米Fe(d=25 nm)热力学函数, 并与文献报导的粗晶Fe及粒径87 nm Fe的热容进行了比较, 从能量角度分析了不同粒径Fe热容曲线差别产生的原因.     

硼砂水溶液的低温热容及热化学性质研究

利用精密绝热量热仪测定了0.03355mol·kg-1的硼砂水溶液在78～351K温区的热容,从实验热容测定结果得到了该水溶液的凝固点为272.905K。用最小二乘法将实验热容值对温度进行拟合,建立了该溶液的热容随温度变化的多项式方程。根据热力学函数关系式,用此多项式方程进行数值积分,获得了以298.15K为基准的该溶液在80～350K温区每隔5K的热力学函数值,并计算出摩尔熔化焓和熔化熵分别为4.536kJ·mol-1和16.22J·K-1·mol-1。根据溶液凝固点降低值,计算出了该溶液的活度为0.99763。     

纳米氧化锌的低温热容和热力学性质

用扫描电子显微镜(SEM)测定了纳米氧化锌试样的粒径, SEM结果表明ZnO试样平均粒径为30 nm. 在83～350 K温区, 用精密低温绝热量热计测定了ZnO的等压摩尔热容, 拟合出其等压摩尔热容与热力学温度的函数关系式: C_p＝－3.249＋0.2400T－3.413×10^－4T ²＋4.485×10^－7T ³. 根据热容与热力学函数关系, 计算了以298.15 K为基准的纳米ZnO的热力学函数, 并与粗晶ZnO和18 nm ZnO热容文献报导值进行了比较, 从能量角度分析了不同粒径ZnO热容曲线差别产生的原因.     

二元有机液体混合物热容与过剩热容的测定

溶液的热容及过剩热容是热力学的重要函数，对其测定与研究具有理论与实际意义．首先，热容是化工传热计算中的基础数据，过剩热容则可检验溶液中分子间的相互作用，并可利用其计算混合物的热容．本文报告了用法国Setaram公司生产的MS-80型Calvet微量热仪对环己酮-芳烃（苯、甲     

尿嘧啶和5-溴尿嘧啶的低温热容

采用综合物性测量系统(PPMS)的热容测量模块在1.9-300 K温度区间内对两种药物中间体(尿嘧啶和5-溴尿嘧啶)的低温热容进行了测量与研究. 结果表明, 在测量温区内两种化合物的低温热容随温度的上升而逐步增加, 无任何热异常现象产生; 在相同温度下, 5-溴尿嘧啶的热容数值始终高于尿嘧啶. 利用低温热容理论模型对热容数据进行了拟合, 并计算得到了0-300 K温区的摩尔熵变、焓变等热力学函数. 此外, 通过热容拟合数据计算得到的尿嘧啶和5-溴尿嘧啶在298.15 K的标准摩尔规定熵分别为(132.48±1.32)和(165.39±1.65) J·K^-1·mol^-1.     

绝热量热和热分析研究8－羟基喹啉的热力学性质

采用绝热量热和热分析技术研究了8-羟基喹啉的热力学性质。用精密绝热量热仪测定了8-羟基喹啉在78 K ~370 K 温区的低温热容。根据实验测定的热容数据计算出了热容拟合方程及热力学函数,得到该物质的熔点、摩尔熔化焓和摩尔熔化熵分别是(345.74±0.15) K、(13.93±0.11) kJ· mol-1 和 (40.26±0.33) J·K-1·mol-1。 根据热力学函数关系式计算了其在78 K ~370 K 温区每隔5 K 的热力学函数 和 。通过部分熔化实验计算出该样品及其绝对纯物质的熔化温度分别是 345.601 K和345.761 K。根据Van’t Hoff方程计算出该样品纯度的摩尔分数为 0.9978。用DSC技术进一步考察了该物质的热稳定性。     

重铬酸钾晶体低温热容及热力学性质的研究

用精密自动绝热量热计测定了重铬酸钾晶体在100～390 K温区内的摩尔热容.实验结果表明在研究温度区间内重铬酸钾无相变和其它热反常现象发生,但其热容在不同的温度范围表现出不同的变化趋势.在100 K≤ T ≤ 275 K和350 K≤ T ≤390 K区间内,其热容随温度的升高明显增大,在275 K≤ T ≤350 K区间,其热容约为定值.将重铬酸钾摩尔热容实验值Cp,m(J•K－1•mol－1)拟合成温度T的多项式方程,在100 K≤ T ≤275 K,为Cp,m=0.0050T2－1.0320T＋125.22； 275 K≤ T ≤ 350 K,为Cp,m=209.37； 350 K≤ T ≤390 K,为Cp,m= 0.0266T2－18.823T＋3542.3.根据热力学函数关系式,从热容值计算出了298.15 K～ 400 K温区范围内每隔5 K的热力学函数值.     

正二十二烷醇的热力学性质

用精密自动绝热量热仪测定了广谱抗病毒药物正二十二烷醇在78-400 K温区的热容. 根据实验测定的热容数据, 用最小二乘法拟合计算出热容对温度的多项式方程, 得到其相变温度、相变焓、相变熵分别为340.844 K、85.07 kJ·mol-1、249.6 J·K-1·mol-1. 根据热力学函数关系式计算了其在80-400 K温区每隔5 K的热力学函数[HT-H298.15]和[ST-298.15]. 用DSC、TG热分析技术进一步考查了该物质在400-900 K的热稳定性.     

苯氧乙酸嘧霉胺盐的低温热容和热力学性质研究

用精密自动绝热量热计测定了苯氧乙酸嘧霉胺盐在81-380 K之间的低温热容. 结果表明, 该化合物在81-328 K之间无相变和热异常现象发生, 在328-354 K之间发生固-液熔化, 其熔化温度、摩尔熔化焓和摩尔熔化熵分别为(349.38±0.03) K, (34.279±10) kJ/mol和(98.13±0.05) J/（K·mol）. 根据热力学函数关系式计算出苯氧乙酸嘧霉胺盐在80-325 K之间以标准状态(298.15 K)为基准的热力学函数值.     

四硼酸锂水溶液体系的热容及离子相互作用

采用Setaram BT 2.15微量热仪测定了Li₂B₄O₇-H₂O体系(Li₂B₄O₇的浓度为0.00415~0.4208 mol/kg)在298.15, 308.15和323.15 K下的热容, 分别计算了不同温度和浓度下的表观摩尔热容, 并获得了不同温度下表观摩尔热容与浓度的关系式. 基于Li₂B₄O₇-H₂O体系的热容测定结果, 应用Pitzer电解质溶液离子相互作用表观摩尔热容模型, 拟合获得了四硼酸锂在不同温度下的Pitzer单盐参数.     

Thermal Analysis of Binary Mixtures of Imidazolium,Pyridinium, Pyrrolidinium,and Piperidinium Ionic Liquids

Ionic liquids (ILs) are being widely studied due to their unique properties, which make them potential candidates for conventional solvents. To study whether binary mixtures of pure ionic liquids provide a viable alternative to pure ionic liquids for different applications, in this work, the thermal analysis and molar heat capacities of five equimolar binary mixtures of ionic liquids based on imidazolium, pyridinium, pyrrolidinium, and piperidinium cations with dicyanamide, trifluoromethanesulfonate, and bis(trifluoromethylsulfonyl)imide anions have been performed. Furthermore, two pure ionic liquids based on piperidinium cation have been thermally characterized and the heat capacity of one of them has been measured. The determination and evaluation of both the transition temperatures and the molar heat capacities was carried out using differential scanning calorimetry (DSC). It was observed that the thermal behavior of the mixtures was completely different than the thermal behavior of the pure ionic liquids present, while the molar heat capacities of the binary mixtures were very similar to the value of the average of molar heat capacities of the two pure ionic liquids.     

Evaluation of interfacial region of microphase-separated SEBS using modulated differential scanning calorimetry and dynamic mechanical thermal analysis

The continuous structural changes of Poly(styrene-b-ethylene-butylene-b-styrene) [SEBS] due to the effect of temperature are hard to evaluate using conventional differential scanning calorimetry (DSC). This paper presents an accurate and simple way to evaluate microstructural and glass transitions of SEBS using modulated differential scanning calorimetry (MDSC). The weak crystalline nature of –(CH₂-CH₂)–_n in the ethylene-butylene (EB) block melted around 36 °C. The premature molecular moment and Tg of the styrene block were at 62 °C and 96 °C, respectively. The interfacial region at high temperature was explained with respect to order-order transition (OOT) at 144 °C and a prominent Order-Disorder Transition (ODT) at around 202 °C. Dynamic mechanical thermal analysis (DMTA) and dynamic mechanical rheological testing (DMRT) measurements also revealed that the T_g of the PS transition were consistent at around 96 °C.     

Some elements in specific heat capacity measurement and numerical simulation of temperature modulated DSC (TMDSC) with R/C network

One important application of temperature modulated DSC (TMDSC) is the measurement of specific heat of materials. In this paper, a thermal resistance/capacitance (R/C) numerical model is used to analyze the effects of experimental parameters and calibration on the measurement of specific heat in TMDSC under isothermal conditions. The actual TMDSC experiments were conducted with sapphire and pure copper samples, respectively. Both simulation and experiments showed that in TMDSC, the measured sample specific heat is a non-linear function of many factors such as sample mass, the heat transfer properties of the TMDSC instrument, temperature modulation period, the heat capacity difference between calibration material and the test material, but modulation amplitude has very little effect on the results. The typical behavior of a heat flux type TMDSC can be described as a low pass filter in terms of specific heat capacity measurement when the instrument heat transfer properties are taken into account. At least for metallic materials, where the temperature gradient inside the sample can normally be ignored, the sample should be chosen in such a way that its total heat capacity (mass times specific heat) is close to that of the calibration material in order to get a more accurate result. Also, a large modulation period is beneficial to improving the test accuracy.     

Study on the capacities,heats of dilution and properties of concentrated potassium carnallite solutions at 298.15 K

The heats of dilution of the infinitesimally dilute potassium carnallite solutions at 298.15 K have been studied by continuous titration from 1.8942 to 0.01044 mol·kg^?1, and an equation for the curve of heats of dilution has been fitted. It was shown that the enthalpy of dilution for the same concentration of the carnallite solution is equal to the sum of those of KCl and MgCl₂ solutions. The equation for the curve of enthalpy of dilution corresponds to that of natural carnallite.     

Thermal behaviour of transition-and tetravalentmetal oxides and phosphorous oxide composites

The heat capacity of the solid indium nitride was measured, using the Calvet TG-DSC 111 differential scanning microcalorimeter (Setaram, France), in the temperature between (314–978 K). The temperature dependence of the heat capacity can be presented in the following form: C _p=41.400+0.499·10⁻³ T−135502T ⁻²−26169900 T ⁻³.     

Low temperature micro-calorimetry by differential scanning

We describe the construction, operation and performance of a fully automated low temperature differential micro-calorimeter for heat capacity measurements on small samples (m < 100 mg) in the temperature range from 15 K to 300 K. The instrument is operated using different calorimetric methods, in particular adiabatic differential scanning. Its reliability is demonstrated by measuring the heat capacity of 23 mg of copper and 37 mg of cyclopentane with an error of less than 2%.

---

Zusammenfassung Es wird der Aufbau, die Funktions- und Arbeitsweise eines vollautomatisierten Differential-Mikrokalorimeters für Wärmekapazitätsmessungen kleiner Proben (m < 100 mg) im Temperaturbereich 15–300 K beschrieben. Die Funktionsweise des Gerätes beruht auf verschiedenen kalorimetrischen Methoden, insbesondere aufadiabatischem Differential-Scanning, Seine Zuverlässigkeit wird durch die Messung der Wärmekapazität einer 23 mg-Kupferprobe und einer 37 rag-Cyclopentanprobe mit einem Me\fehler von kleiner als 2% demonstriert.

     

Heat capacity measurement by modulated DSC at constant temperature

The mathematical equations for step-wise measurement of heat capacity (C _p ) by modulated differential scanning calorimetry (MDSC) are discussed for the conditions of negligible temperature gradients within sample and reference. Using a commercial MDSC, applications are evaluated and the limits explored. This new technique permits the determination ofC _p by keeping the sample continually close to equilibrium, a condition conventional DSC is unable to meet. Heat capacity is measured at ‘practically isothermal condition’ (often changing not more than ±1 K). The method provides data with good precision. The effects of sample mass, amplitude and frequency of temperature modulation were studied and methods for optimizing the instrument are proposed. The correction for the differences in sample and reference heating rates, needed for high-precision data by standard DSC, do not apply for this method. Presented in preliminary from at the 22nd NATAS Conference in Denver, CO 9/19-22/93 (Proceedings, pages 59–64, editor K. R. Williams).     

Heat capacity of crystalline GaN

The heat capacity of gallium nitride has been measured by DSC method using DuPont Thermal Analyst 2100, DSC 951 unit in the temperature range (300–850 K). The temperature dependence of the heat capacity can be presented in the following form: C _p=32.960+0.162·10⁻¹ T+2360170T ⁻²-775370000T ⁻³.     

Polymorphic and Thermodynamic Study of Indomethacin

Indomethacin is known to exhibit polymorphism. As a consequence the various forms have different solubilities and may have different bioavailabilities. This study has been carried out with the following techniques: calorimetry, differential scanning calorimetry (DSC), thermogravimetric analysis (TG), X-ray diffraction and thermomicroscopy. Two solid forms have been prepared and studied: their melting temperature and their enthalpy of fusion are determined. The heat capacity and heat content were measured vs. the temperature for these two solid forms and for the liquid phase. This is fundamental for the determination of the stable form. More of this, with a view to study phase diagrams of indomethacin with another compound (solvent or not), the knowledge of the C _p of the various forms is necessary for calculation of the liquidus curve, this allows to minimize the number of experiments. This revised version was published online in August 2006 with corrections to the Cover Date.