苯氧乙酸烯丙酯的合成

对苯酚和氯乙酸的Williamson反应加以改进,使苯氧乙酸的收率达到95．4％。并以苯氧乙酸和烯丙醇为原料,活性碳负载磷钨酸为催化剂,合成了苯氧乙酸烯丙酯。考察了两个反应的主要影响因素。     

乙酰乙酸乙酯制备实验的改进

乙酰乙酸乙酯的制备,实验教材上是以乙酸乙酯为原料,钠作缩合试剂,通过Claisen缩合反应制备。其实验存在着安全性差、耗时长、产品纯度差和收率低等不足。依据实验的目的、原理、内容不变的原则,采用钠与乙酸乙酯物质的量比为0.52,回流下加入细砂搅拌制备钠珠,缩合反应过程加入环己烷,分馏提纯产品等措施进行改进实验。改进后的实验操作的安全性和产品的质量提高,产品收率可达70%以上。     

N-(1-环己烯基)吗啉制备实验的改进

实验教材上以吗啉和环己酮为原料,对甲基苯磺酸为催化剂,甲苯作带水剂,通过缩合反应制备N-(1-环己烯基)吗啉。实验存在着耗时长、易造成实验室内有毒气体甲苯含量高、产品色泽深和收率低(小于60%)等不足。依据实验的目的、原理、内容不变的原则,采用 n/n为1.6,预缩合反应1 h后加入共沸剂,反应加入对苯二酚,环己烷作共沸剂,分馏提纯产品等措施进行改进实验。改进后的实验,反应时间缩短了1 h、室内空气环境友好、产品近乎无色、收率可达80%以上。环己酮吗啉     

金属镝生产工艺的改良

实验主要针对金属Dy一次还原生产中的氩气充入量、还原剂Ca加入量、二次精炼过程中精炼时间以及精炼温度分别进行控制,在生产结束后对所产金属杂质含量进行汇总分析。结果表明:氩气压力过大或过小,对还原反应都会造成不利影响,将氩气压力设定在-0.07MPa时,所获得的金属收率可控制在97.5%以上;实验中加入过量25.8%的Ca所获得的金属收率超过97.5%,进入粗金属中的杂质Ca,Fe都控制在比较低的水平;在精炼时间为40 min的条件下,精炼温度保持在1500℃左右时,收率达到99.7%,金属中W,Fe等杂质含量相对较低。对于生产高纯金属Dy,通过改进相关工艺参数,完全可以实现产品品质的进一步提高。     

改性活性炭负载三聚磷酸二氢铝催化合成苯甲醛乙二醇缩醛

采用硝酸改性活性炭后负载三聚磷二氢铝用于催化合成苯甲醛乙二醇缩醛,通过单因素实验考察醇醛摩尔比、催化剂用量及反应时间等因素对产品收率的影响,并采用正交实验获取较佳工艺条件。 结果表明,该催化反应中,当反应温度为110 ℃时,各因素对收率的影响顺序为:醇醛比>反应时间>带水剂加入量>催化剂用量。 优化反应条件为:苯甲醛0.2 mol,醇醛摩尔比2.5,反应时间75 min,催化剂加入量4%(占反应物总质量),带水剂加入量25 mL,苯甲醛乙二醇缩醛收率86.5%,催化剂经5次重复使用后收率仍大于86.0%。     

N-(取代苯氧乙酰基)-N'-(4-苯基噻唑-2-基)硫脲的合成

以取代苯酚和氯乙酸为原料,合成取代苯氧乙酸,然后经过酰氯化,酯化得到取代苯氧乙酰基异硫氰酸酯,再和2-氨基-4-苯基噻唑反应得到4种N-(取代苯氧乙酰基)-N'-(4-苯基噻唑-2-基)硫脲类化合物,其中3种化合物为首次报道。化合物结构经1H NMR、IR和元素分析得到确证。初步室内生测结果表明该类化合物具有一定的抑菌活性。     

串联反应合成氟磺酸联苯酚酯

发展了一个以溴代苯酚为原料通过串联反应制备氟磺酸联苯酚酯的反应体系.该体系以钯碳为催化剂,无水碳酸钾为碱,乙醇水溶液为溶剂,室温下进行Suzuki反应后,通入硫酰氟气体,最终得到氟磺酸联苯酚酯.反应过程中无需分离中间体,无需加入有机膦配体及氮气保护反应,操作简便,反应条件温和,官能团底物兼容性好,产品分离收率最高达92.6%;此外,钯碳催化剂可回收使用三次几乎不失去活性.     

磷钨酸催化合成氯乙酸异丙酯

研究了磷钨酸催化氯乙酸与异丙醇合成氯乙酸异丙酯的反应 ,讨论了影响合成的因素 ,找出了最佳合成条件 ,收率达到 90 %。     

氨基磺酸催化合成氯乙酸正丁酯

氨基磺酸能够代替硫酸作为酯化催化剂。研究了以氨基磺酸为催化剂,氯乙酸与正丁醇合成氯乙酸正丁酯。研究了反应的影响因素和催化剂的重复使用性能。当氯乙酸、正丁醇和氨基磺酸的摩尔比为0.05:0.15:0.00773,回流分水90min时,酯收率达82.4%。并以氨基磺酸为催化剂合成了氯乙酸异丁酯、氯乙酸仲丁酯、氯乙酸正戊酯、氯乙酸异戊酯和氯乙酸2-戊酯。     

高浓度含酚废水中酚类的转化回收及脱除

以含量30 g/L的苯酚水溶液为模型,提出氯化联合氧化工艺,实现对高浓度含酚废水中苯酚的转化回收及残余酚类的氧化脱除。 首先以pH值作为指示,向溶液中引入足够量的氯离子和氢离子,通过加入氯酸钠与之反应定量产生氯气;在所控制的实验条件下,氯气与溶液中的苯酚选择性反应转化为低溶解度的三氯苯酚沉淀,经气相色谱-质谱（GC-MS）面积归一法测得其含量可达97.76%;过滤所得滤液化学需氧量（COD）降低至1125 mg/L,苯酚回收率约98.7%。 采用Fenton氧化技术对该滤液进行氧化降解,结果表明,在优化的实验条件pH=3、Fe2+浓度为1 mmol/L下,H2O2用量为15 mL/L时,残余的氯酚类即可以被有效降解,降解后的水样经调碱性将铁或亚铁离子沉淀后为无色透明的溶液;联合处理后,水样COD减小到52 mg/L,该值满足国家工业污水排放标准。     

电堆集富集非水毛细管电泳同时测定水杨酸、肉桂酸、阿魏酸和香草酸

建立了同时分离测定水杨酸、肉桂酸、阿魏酸和香草酸的电堆集富集-非水毛细管电泳(NACE)的新方法。运行缓冲溶液为40mmol/L乙酸钠-2.5mmol/L氢氧化钠甲醇溶液,电压-25kV,在225nm波长下紫外检测。对电压、乙酸钠浓度、氢氧化钠浓度、进样时间、样品溶液等因素对电堆集及分离的影响做了系统的研究。水杨酸、肉桂酸、阿魏酸和香草酸分别在1.4~28mg/L、0.40~8.0mg/L、0.7~18mg/L和0.7~30mg/L范围内线性关系良好(r=0.9999、r=0.9997、r=0.9994、r=0.9997);回收率分别为95.8~99.6%、96.2~98·2%、95.7~105%和98.9~103%,基于3倍信噪比(S/N=3),4种有机酸的检出限分别为0.069、0.051、0.107和0.089mg/L。     

离子色谱法测定乙醛酸中的顺丁烯二酸和乙二酸

采用抑制电导离子色谱法测定高浓度乙醛酸基体中痕量的顺丁烯二酸和乙二酸。将乙醛酸样品稀释至1 000倍体积后,采用高浓度的淋洗液,以高容量色谱柱对样品进行分析。实验结果表明,顺丁烯二酸和乙二酸最低检出限分别为12.7,19.6μg/L,重现性(n=5)分别为1.13%,1.11%,回收率分别为97.9%,94.7%。该方法具有较高的灵敏度,适用于乙醛酸的例行检测。     

对氨基苯甲酸的合成研究进展

综述了以对硝基苯甲酸为原料合成对氨基苯甲酸的近期研究进展。并从技术和经济角度讨论了各种合成方法的优点与不足。     

Determination of Cyanuric Acid or Trichloroisocyanuric Acid in Air

Abstract

An analytical procedure for measurement of cyanuric acid or trichlor oisocyanuric acid in air has been developed. The procedure involves air sampling with a 37-mm PVC membrane filter, recovery with a phosphate buffer, and analysis by high performance liquid chromatography with a UV detector at 225 nm. The interior surface of the front piece of the cassette filter holder also is analyzed. Average recoveries were 0.98 to 1.00 after fortification of PVC filters with 12- to 412-μg quantities of cyanuric acid. Average recoveries of trichloroisocyanuric acid were 0.83 to 0.98 after fortification of glass surfaces with 12- to 424-μg quantities (these are reasonable approximations for recoveries of trichloroisocyanuric acid from PVC filters). The analyst should ascertain which analyte is present at the sampling site because trichloroisocyanuric acid reacts with water in the phosphate buffer to form cyanuric acid in high yield.     

Surface Functionalization of Magnetite Nanoparticles with Sulfonic Acid and Heteropoly Acid: Efficient Magnetically Recoverable Solid Acid Catalysts

New magnetically recoverable solid acid catalysts for acid‐catalyzed reactions were designed via the surface chemical functionalization of silica‐coated magnetite nanoparticles (SCMNPs) with sulfonic acid groups. First, the SCMNPs were covalently functionalized with 3‐aminopropyl groups to achieve Amp‐SCMNPs. Then, reaction of the Amp‐SCMNPs with 1,4‐butane sultone followed by acidification with phosphotungstic acid (HPW) or diluted sulfuric acid produced magnetically recoverable solid acid catalysts, HPW‐ampsul‐SCMNPs and H‐ampsul‐SCMNPs, respectively. Both catalysts were characterized by various physicochemical analyses such as Fourier transform infrared (FT‐IR) and inductively coupled plasma‐optical emission (ICP‐OES) spectroscopies, vibrating sample magnetometry (VSM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X‐ray diffraction (XRD), and energy‐dispersive X‐ray (EDX) analyses. Finally, the catalytic activities of the prepared catalysts were examined in the esterification of acetic acid with butanol and acetalization of benzaldehyde with ethylene glycol. Excellent catalytic efficiencies were obtained in both cases. The catalysts were consecutively recovered and reused five times without significant loss of their activities.     

以对甲基苯磺酸作为淋洗液用离子色谱法测定酸雨中的有机酸

本文研究了用对甲基苯磺酸作为淋洗液测定液相中HCOO~-和CH_3COO~-的离子色谱条件,该方法对HCOO~-和CH_3COO~-的最低检出限分别为48ppb和93ppb。该方法与用进口的辛磺酸作为淋洗液的方法进行了对比实验,并用于两广实际酸雨样品中甲酸和乙酸的测量。     

Mechanochemical Complexation between Deoxycholic Acid and Salicylic Acid

A complex between deoxycholic acid (DCA) and salicylic acid (SA) was prepared by grinding and coprecipitation methods. The resultant complex was characterized by means of powder X-ray diffractometry, IR spectroscopy and thermal analysis. The stoichiometry (DCA : SA 1 : 1) of the complex obtained by grinding was identical to that obtained by coprecipitation. The powder X-ray diffraction pattern of the DCA–SA complex differed from the typical pattern of DCA–guest complexes such as DCA–camphor and DCA–phenanthrene complexes. IR spectra suggested that a different kind of hydrogen bonding was formed in the crystal of the DCA–SA complex, compared with the other DCA–guest complexes. This was in good agreement with data from the crystal structure.     

硝酸氧解法提高泥炭中黄腐酸的产率

硝酸氧解法提高泥炭中黄腐酸的产率;腐植酸;硝酸氧化降解     

Determination of Monochloroacetic Acid and Dichloroacetic Acid for Quality Control of Acetic Acid Chlorination Industry by Ion Chromatography

An ion chromatographic method is described for the purpose of quality control in the process of monochloroacetic acid production. Using 2.5 mM NaOH–10% methanol as eluent, the simultaneous determination of acetic acid, monochloroacetic acid, dichloroacetic acid, and Cl⁻ was obtained in a single run. Monochloroacetic acid and dichloroacetic acid showed good linearity in the range 0.1–20 and 0.15–20 μg/ml and correlation coefficients were 0.9999 and 0.9998, respectively. The detection limits (signal-to-noise ratio 3:1) of monochloroacetic acid and dichloroacetic acid were 17 and 25 ng/ml. This simple, sensitive, and time-saving method can be applied for composition analysis in acetic acid chlorination production.